February 2014 - U-Boot

[U-Boot] [PATCH] at91sam9263ek: add mmc support
by Andreas Henriksson 09 Mar '14

09 Mar '14

Add support for using the Atmel MCI driver on at91sam9263ek. This change is modeled after the existing at91sam9260ek support. Please note that this hooks up slot1 (MCI1) for SD. Not both. Tested with at91bootstrap and u-boot on dataflash in slot 0 and fat-formatted 8GB SDHC in slot 1 on first revision at91sam9263ek (which must use dataflash in slot0 to boot). CONFIG_ATMEL_MCI_PORTB not tested. Signed-off-by: Andreas Henriksson <andreas.henriksson(a)endian.se> --- arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c | 26 +++++++++++++++++++++ board/atmel/at91sam9263ek/at91sam9263ek.c | 10 ++++++++ include/configs/at91sam9263ek.h | 13 ++++++++++ 3 files changed, 49 insertions(+), 0 deletions(-) diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c index 99a3913..5496e55 100644 --- a/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c +++ b/arch/arm/cpu/arm926ejs/at91/at91sam9263_devices.c @@ -143,6 +143,32 @@ void at91_spi1_hw_init(unsigned long cs_mask) } #endif +#if defined(CONFIG_GENERIC_ATMEL_MCI) +void at91_mci_hw_init(void) +{ + /* Enable mci clock */ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + writel(1 << ATMEL_ID_MCI1, &pmc->pcer); + + at91_set_a_periph(AT91_PIO_PORTA, 6, PUP); /* MCI1_CK */ + +#if defined(CONFIG_ATMEL_MCI_PORTB) + at91_set_a_periph(AT91_PIO_PORTA, 21, PUP); /* MCI1_CDB */ + at91_set_a_periph(AT91_PIO_PORTA, 22, PUP); /* MCI1_DB0 */ + at91_set_a_periph(AT91_PIO_PORTA, 23, PUP); /* MCI1_DB1 */ + at91_set_a_periph(AT91_PIO_PORTA, 24, PUP); /* MCI1_DB2 */ + at91_set_a_periph(AT91_PIO_PORTA, 25, PUP); /* MCI1_DB3 */ +#else + at91_set_a_periph(AT91_PIO_PORTA, 7, PUP); /* MCI1_CDA */ + at91_set_a_periph(AT91_PIO_PORTA, 8, PUP); /* MCI1_DA0 */ + at91_set_a_periph(AT91_PIO_PORTA, 9, PUP); /* MCI1_DA1 */ + at91_set_a_periph(AT91_PIO_PORTA, 10, PUP); /* MCI1_DA2 */ + at91_set_a_periph(AT91_PIO_PORTA, 11, PUP); /* MCI1_DA3 */ +#endif +} +#endif + + #ifdef CONFIG_MACB void at91_macb_hw_init(void) { diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c index d42a173..4b14554 100644 --- a/board/atmel/at91sam9263ek/at91sam9263ek.c +++ b/board/atmel/at91sam9263ek/at91sam9263ek.c @@ -24,6 +24,7 @@ #include <net.h> #endif #include <netdev.h> +#include <atmel_mci.h> DECLARE_GLOBAL_DATA_PTR; @@ -214,6 +215,15 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif +#ifdef CONFIG_GENERIC_ATMEL_MCI +int board_mmc_init(bd_t *bd) +{ + at91_mci_hw_init(); + + return atmel_mci_init((void *)ATMEL_BASE_MCI1); +} +#endif + int board_early_init_f(void) { struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index b9aa036..48c12ea 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -103,6 +103,7 @@ #define CONFIG_CMD_PING 1 #define CONFIG_CMD_DHCP 1 #define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_MMC #define CONFIG_CMD_USB 1 /* SDRAM */ @@ -123,6 +124,18 @@ #define DATAFLASH_TCSS (0x1a << 16) #define DATAFLASH_TCHS (0x1 << 24) +/* MMC */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_GENERIC_ATMEL_MCI +#endif + +/* FAT */ +#ifdef CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + /* NOR flash, if populated */ #ifdef CONFIG_SYS_USE_NORFLASH #define CONFIG_SYS_FLASH_CFI 1 -- 1.5.4.3

2 1

[U-Boot] Questions on adding a new type to mkimage
by Charles Manning 09 Mar '14

09 Mar '14

I am in the throes of extending mkimage to add socfpga support. This is my first time in mkimage, so please forgive me being on a learning curve. It seems that the most "normal" path for mkimage signers is to append some sort of header to the front of the image ie the flow is write header out copy image data with copy_file call set_header The socfpga preloader needs something a bit different. It does not add a header, but instead adds a tail (CRC+padding) and mashes some bytes into a known place in the image. Unfortunately the mkimage framework does not seem to provide an "add tail" function which is really what is needed here. The only way I can see to extend the size of the image, using the normal mkimage workflow would be to do something like this: *Provide vrec_header which adds a fake header of 64k - input_size. * Allow copy_file to then do the copy step. * I now have a 64k "image" which is 64k-size 0 bytes, followed by the actual input_data. * When set_header is called, shift the actual input data to where it should be, add the CRC and fix up the padding. This seems needlessly contrived to work with the framework. Or the alternative might be just to treat this as a special case.... Thoughts/opinions??? Thanks Charles

2 1

[U-Boot] [PATCH][v2] powerpc/t104xrdb: Update DDR initialization related settings
by Priyanka Jain 08 Mar '14

08 Mar '14

Update following DDR related settings for T1040RDB, T1042RDB_PI -Correct number of chip selects to two as t1040 supports two Chip selects. -Update board_specific_parameters udimm structure with settings derived via calibration. -Update ddr_raw_timing sructure corresponding to DIMM. -Set ODT to off. Typically on FSL board, ODT is set to 75 ohm, but on T104xRDB, on setting this , DDR instability is observed. Board-level debugging is in progress. Verified the updated settings to be working fine with dual-ranked Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s. Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> Signed-off-by: York Sun <yorksun(a)freescale.com> --- Changes for v2: Udpated description related to ODT off, Removed cpo, write_data_delay, force_2t parameters as they are not longer used. board/freescale/t104xrdb/ddr.c | 13 +++---------- board/freescale/t104xrdb/ddr.h | 38 ++++++++++++++++++++------------------ include/configs/T1040RDB.h | 2 +- include/configs/T1042RDB_PI.h | 2 +- 4 files changed, 25 insertions(+), 30 deletions(-) diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c index 9009afa..57d0f9c 100644 --- a/board/freescale/t104xrdb/ddr.c +++ b/board/freescale/t104xrdb/ddr.c @@ -46,7 +46,7 @@ void fsl_ddr_board_options(memctl_options_t *popts, pbsp = udimms[0]; - /* Get clk_adjust, cpo, write_data_delay,2t, according to the board ddr + /* Get clk_adjust according to the board ddr * freqency and n_banks specified in board_specific_parameters table. */ ddr_freq = get_ddr_freq(0) / 1000000; @@ -54,14 +54,10 @@ void fsl_ddr_board_options(memctl_options_t *popts, if (pbsp->n_ranks == pdimm->n_ranks && (pdimm->rank_density >> 30) >= pbsp->rank_gb) { if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->cpo_override = pbsp->cpo; - popts->write_data_delay = - pbsp->write_data_delay; popts->clk_adjust = pbsp->clk_adjust; popts->wrlvl_start = pbsp->wrlvl_start; popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp->force_2t; goto found; } pbsp_highest = pbsp; @@ -74,13 +70,10 @@ void fsl_ddr_board_options(memctl_options_t *popts, printf("for data rate %lu MT/s\n", ddr_freq); printf("Trying to use the highest speed (%u) parameters\n", pbsp_highest->datarate_mhz_high); - popts->cpo_override = pbsp_highest->cpo; - popts->write_data_delay = pbsp_highest->write_data_delay; popts->clk_adjust = pbsp_highest->clk_adjust; popts->wrlvl_start = pbsp_highest->wrlvl_start; popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp_highest->force_2t; } else { panic("DIMM is not supported by this board"); } @@ -112,8 +105,8 @@ found: popts->zq_en = 1; /* DHC_EN =1, ODT = 75 Ohm */ - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF); } phys_size_t initdram(int board_type) diff --git a/board/freescale/t104xrdb/ddr.h b/board/freescale/t104xrdb/ddr.h index 9276b59..09b30b9 100644 --- a/board/freescale/t104xrdb/ddr.h +++ b/board/freescale/t104xrdb/ddr.h @@ -6,7 +6,6 @@ #ifndef __DDR_H__ #define __DDR_H__ - dimm_params_t ddr_raw_timing = { .n_ranks = 2, .rank_density = 2147483648u, @@ -14,22 +13,21 @@ dimm_params_t ddr_raw_timing = { .primary_sdram_width = 64, .ec_sdram_width = 8, .registered_dimm = 0, - .mirrored_dimm = 1, + .mirrored_dimm = 0, .n_row_addr = 15, .n_col_addr = 10, .n_banks_per_sdram_device = 8, .edc_config = 2, /* ECC */ .burst_lengths_bitmask = 0x0c, - .tckmin_x_ps = 1071, - .caslat_x = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */ - .taa_ps = 13910, + .caslat_x = 0xfe << 4, /* 5,6,7,8,9,10,11 */ + .taa_ps = 13125, .twr_ps = 15000, - .trcd_ps = 13910, + .trcd_ps = 13125, .trrd_ps = 6000, - .trp_ps = 13910, + .trp_ps = 13125, .tras_ps = 34000, - .trc_ps = 48910, + .trc_ps = 48125, .trfc_ps = 260000, .twtr_ps = 7500, .trtp_ps = 7500, @@ -45,9 +43,6 @@ struct board_specific_parameters { u32 wrlvl_start; u32 wrlvl_ctl_2; u32 wrlvl_ctl_3; - u32 cpo; - u32 write_data_delay; - u32 force_2t; }; /* @@ -59,14 +54,21 @@ struct board_specific_parameters { static const struct board_specific_parameters udimm0[] = { /* * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + * num| hi| rank| clk| wrlvl | wrlvl + * ranks| mhz| GB |adjst| start | ctl2 */ - {2, 1066, 4, 8, 4, 0x05070609, 0x08090a08, 0xff, 2, 0}, - {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, - {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, - {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, + {2, 833, 4, 4, 6, 0x06060607, 0x08080807}, + {2, 833, 0, 4, 6, 0x06060607, 0x08080807}, + {2, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09}, + {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09}, + {2, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A}, + {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A}, + {1, 833, 4, 4, 6, 0x06060607, 0x08080807}, + {1, 833, 0, 4, 6, 0x06060607, 0x08080807}, + {1, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09}, + {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09}, + {1, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A}, + {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A}, {} }; diff --git a/include/configs/T1040RDB.h b/include/configs/T1040RDB.h index 7cfda50..c6c214c 100644 --- a/include/configs/T1040RDB.h +++ b/include/configs/T1040RDB.h @@ -147,7 +147,7 @@ /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ #define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) #define CONFIG_DDR_SPD #define CONFIG_SYS_DDR_RAW_TIMING diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h index ed9ca8a..5102d49 100644 --- a/include/configs/T1042RDB_PI.h +++ b/include/configs/T1042RDB_PI.h @@ -147,7 +147,7 @@ /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ #define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) #define CONFIG_DDR_SPD #define CONFIG_SYS_DDR_RAW_TIMING -- 1.7.4.1

2 1

[U-Boot] [PATCH][v2] powerpc/t1040qds: Add Video - HDMI support
by Priyanka Jain 08 Mar '14

08 Mar '14

T1040 has internal display interface unit (DIU) for driving video. T1040QDS supports video mode via -LCD using TI enconder -HDMI type interface via HDMI encoder Chrontel, CH7301C encoder which is I2C programmable is used as HDMI connector on T1040QDS. This patch add support to -enable Video interface for T1040QDS -route qixis multiplexing to enable DIU-HDMI interface on board -program DIU pixel clock gerenartor for T1040 -program HDMI encoder via I2C on board Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> --- Changes for v2: Fix compilation warnings Depends on http://patchwork.ozlabs.org/patch/315294/ board/freescale/t1040qds/Makefile | 1 + board/freescale/t1040qds/diu.c | 215 +++++++++++++++++++++++++++++ board/freescale/t1040qds/t1040qds.h | 1 + board/freescale/t1040qds/t1040qds_qixis.h | 12 ++ include/configs/T1040QDS.h | 27 ++++- 5 files changed, 255 insertions(+), 1 deletions(-) create mode 100644 board/freescale/t1040qds/diu.c diff --git a/board/freescale/t1040qds/Makefile b/board/freescale/t1040qds/Makefile index c7470d7..19ed21b 100644 --- a/board/freescale/t1040qds/Makefile +++ b/board/freescale/t1040qds/Makefile @@ -10,3 +10,4 @@ obj-$(CONFIG_PCI) += pci.o obj-y += law.o obj-y += tlb.o obj-y += eth.o +obj-y += diu.o diff --git a/board/freescale/t1040qds/diu.c b/board/freescale/t1040qds/diu.c new file mode 100644 index 0000000..ffd074b --- /dev/null +++ b/board/freescale/t1040qds/diu.c @@ -0,0 +1,215 @@ +/* + * Copyright 2014 Freescale Semiconductor, Inc. + * Author: Priyanka Jain <Priyanka.Jain(a)freescale.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <linux/ctype.h> +#include <asm/io.h> +#include <stdio_dev.h> +#include <video_fb.h> +#include <fsl_diu_fb.h> +#include "../common/qixis.h" +#include "t1040qds.h" +#include "t1040qds_qixis.h" +#include <i2c.h> + + +#define I2C_DVI_INPUT_DATA_FORMAT_REG 0x1F +#define I2C_DVI_PLL_CHARGE_CNTL_REG 0x33 +#define I2C_DVI_PLL_DIVIDER_REG 0x34 +#define I2C_DVI_PLL_SUPPLY_CNTL_REG 0x35 +#define I2C_DVI_PLL_FILTER_REG 0x36 +#define I2C_DVI_TEST_PATTERN_REG 0x48 +#define I2C_DVI_POWER_MGMT_REG 0x49 +#define I2C_DVI_LOCK_STATE_REG 0x4D +#define I2C_DVI_SYNC_POLARITY_REG 0x56 + +/* + * Set VSYNC/HSYNC to active high. This is polarity of sync signals + * from DIU->DVI. The DIU default is active igh, so DVI is set to + * active high. + */ +#define I2C_DVI_INPUT_DATA_FORMAT_VAL 0x98 + +#define I2C_DVI_PLL_CHARGE_CNTL_HIGH_SPEED_VAL 0x06 +#define I2C_DVI_PLL_DIVIDER_HIGH_SPEED_VAL 0x26 +#define I2C_DVI_PLL_FILTER_HIGH_SPEED_VAL 0xA0 +#define I2C_DVI_PLL_CHARGE_CNTL_LOW_SPEED_VAL 0x08 +#define I2C_DVI_PLL_DIVIDER_LOW_SPEED_VAL 0x16 +#define I2C_DVI_PLL_FILTER_LOW_SPEED_VAL 0x60 + +/* Clear test pattern */ +#define I2C_DVI_TEST_PATTERN_VAL 0x18 +/* Exit Power-down mode */ +#define I2C_DVI_POWER_MGMT_VAL 0xC0 + +/* Monitor polarity is handled via DVI Sync Polarity Register */ +#define I2C_DVI_SYNC_POLARITY_VAL 0x00 + +/* + * DIU Area Descriptor + * + * Note that we need to byte-swap the value before it's written to the AD + * register. So even though the registers don't look like they're in the same + * bit positions as they are on the MPC8610, the same value is written to the + * AD register on the MPC8610 and on the P1022. + */ +#define AD_BYTE_F 0x10000000 +#define AD_ALPHA_C_SHIFT 25 +#define AD_BLUE_C_SHIFT 23 +#define AD_GREEN_C_SHIFT 21 +#define AD_RED_C_SHIFT 19 +#define AD_PIXEL_S_SHIFT 16 +#define AD_COMP_3_SHIFT 12 +#define AD_COMP_2_SHIFT 8 +#define AD_COMP_1_SHIFT 4 +#define AD_COMP_0_SHIFT 0 + +/* Programming of HDMI Chrontel CH7301 connector */ +int diu_set_dvi_encoder(unsigned int pixclock) +{ + int ret; + u8 temp; + select_i2c_ch_pca9547(I2C_MUX_CH_DIU); + + temp = I2C_DVI_TEST_PATTERN_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, I2C_DVI_TEST_PATTERN_REG, 1, + &temp, 1); + if (ret) { + puts("I2C: failed to select proper dvi test pattern\n"); + return ret; + } + temp = I2C_DVI_INPUT_DATA_FORMAT_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, I2C_DVI_INPUT_DATA_FORMAT_REG, + 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi input data format\n"); + return ret; + } + + /* Set Sync polarity register */ + temp = I2C_DVI_SYNC_POLARITY_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, I2C_DVI_SYNC_POLARITY_REG, 1, + &temp, 1); + if (ret) { + puts("I2C: failed to select dvi syc polarity\n"); + return ret; + } + + /* Set PLL registers based on pixel clock rate*/ + if (pixclock > 65000000) { + temp = I2C_DVI_PLL_CHARGE_CNTL_HIGH_SPEED_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, + I2C_DVI_PLL_CHARGE_CNTL_REG, 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll charge_cntl\n"); + return ret; + } + temp = I2C_DVI_PLL_DIVIDER_HIGH_SPEED_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, + I2C_DVI_PLL_DIVIDER_REG, 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll divider\n"); + return ret; + } + temp = I2C_DVI_PLL_FILTER_HIGH_SPEED_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, + I2C_DVI_PLL_FILTER_REG, 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll filter\n"); + return ret; + } + } else { + temp = I2C_DVI_PLL_CHARGE_CNTL_LOW_SPEED_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, + I2C_DVI_PLL_CHARGE_CNTL_REG, 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll charge_cntl\n"); + return ret; + } + temp = I2C_DVI_PLL_DIVIDER_LOW_SPEED_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, + I2C_DVI_PLL_DIVIDER_REG, 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll divider\n"); + return ret; + } + temp = I2C_DVI_PLL_FILTER_LOW_SPEED_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, + I2C_DVI_PLL_FILTER_REG, 1, &temp, 1); + if (ret) { + puts("I2C: failed to select dvi pll filter\n"); + return ret; + } + } + + temp = I2C_DVI_POWER_MGMT_VAL; + ret = i2c_write(CONFIG_SYS_I2C_DVI_ADDR, I2C_DVI_POWER_MGMT_REG, 1, + &temp, 1); + if (ret) { + puts("I2C: failed to select dvi power mgmt\n"); + return ret; + } + + udelay(500); + + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + return 0; +} + +void diu_set_pixel_clock(unsigned int pixclock) +{ + unsigned long speed_ccb, temp; + u32 pixval; + int ret = 0; + speed_ccb = get_bus_freq(0); + temp = 1000000000 / pixclock; + temp *= 1000; + pixval = speed_ccb / temp; + + /* Program HDMI encoder */ + ret = diu_set_dvi_encoder(temp); + if (ret) { + puts("Failed to set DVI encoder\n"); + return; + } + + /* Program pixel clock */ + out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR, + ((pixval << PXCK_BITS_START) & PXCK_MASK)); + /* enable clock*/ + out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR, PXCKEN_MASK | + ((pixval << PXCK_BITS_START) & PXCK_MASK)); +} + +int platform_diu_init(unsigned int xres, unsigned int yres, const char *port) +{ + u32 pixel_format; + u8 sw; + + /*Route I2C4 to DIU system as HSYNC/VSYNC*/ + sw = QIXIS_READ(brdcfg[5]); + QIXIS_WRITE(brdcfg[5], + ((sw & ~(BRDCFG5_IMX_MASK)) | (BRDCFG5_IMX_DIU))); + + /*Configure Display ouput port as HDMI*/ + sw = QIXIS_READ(brdcfg[15]); + QIXIS_WRITE(brdcfg[15], + ((sw & ~(BRDCFG15_LCDPD_MASK | BRDCFG15_DIUSEL_MASK)) + | (BRDCFG15_LCDPD_ENABLED | BRDCFG15_DIUSEL_HDMI))); + + pixel_format = cpu_to_le32(AD_BYTE_F | (3 << AD_ALPHA_C_SHIFT) | + (0 << AD_BLUE_C_SHIFT) | (1 << AD_GREEN_C_SHIFT) | + (2 << AD_RED_C_SHIFT) | (8 << AD_COMP_3_SHIFT) | + (8 << AD_COMP_2_SHIFT) | (8 << AD_COMP_1_SHIFT) | + (8 << AD_COMP_0_SHIFT) | (3 << AD_PIXEL_S_SHIFT)); + + printf("DIU: Switching to monitor @ %ux%u\n", xres, yres); + + + return fsl_diu_init(xres, yres, pixel_format, 0); +} diff --git a/board/freescale/t1040qds/t1040qds.h b/board/freescale/t1040qds/t1040qds.h index 79bdeda..5041f37 100644 --- a/board/freescale/t1040qds/t1040qds.h +++ b/board/freescale/t1040qds/t1040qds.h @@ -9,5 +9,6 @@ void fdt_fixup_board_enet(void *blob); void pci_of_setup(void *blob, bd_t *bd); +int select_i2c_ch_pca9547(u8 ch); #endif diff --git a/board/freescale/t1040qds/t1040qds_qixis.h b/board/freescale/t1040qds/t1040qds_qixis.h index 2ce8795..98d2d39 100644 --- a/board/freescale/t1040qds/t1040qds_qixis.h +++ b/board/freescale/t1040qds/t1040qds_qixis.h @@ -13,6 +13,18 @@ #define BRDCFG4_EMISEL_MASK 0xE0 #define BRDCFG4_EMISEL_SHIFT 5 +/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/ +#define BRDCFG5_IMX_MASK 0xC0 +#define BRDCFG5_IMX_DIU 0x80 + +/* BRDCFG15[3] controls LCD Panel Powerdown*/ +#define BRDCFG15_LCDPD_MASK 0x10 +#define BRDCFG15_LCDPD_ENABLED 0x00 + +/* BRDCFG15[6:7] controls DIU MUX selction*/ +#define BRDCFG15_DIUSEL_MASK 0x03 +#define BRDCFG15_DIUSEL_HDMI 0x00 + /* SYSCLK */ #define QIXIS_SYSCLK_66 0x0 #define QIXIS_SYSCLK_83 0x1 diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index 75ea125..3f26559 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -375,7 +375,7 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (512 * 1024) -#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) +#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) /* Serial Port - controlled on board with jumper J8 * open - index 2 @@ -401,6 +401,25 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +/* Video */ +#define CONFIG_FSL_DIU_FB +#ifdef CONFIG_FSL_DIU_FB +#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000) +#define CONFIG_VIDEO +#define CONFIG_CMD_BMP +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +/* + * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so + * disable empty flash sector detection, which is I/O-intensive. + */ +#undef CONFIG_SYS_FLASH_EMPTY_INFO +#endif + /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT #define CONFIG_OF_BOARD_SETUP @@ -426,6 +445,11 @@ unsigned long get_board_ddr_clk(void); /* I2C bus multiplexer */ #define I2C_MUX_CH_DEFAULT 0x8 +#define I2C_MUX_CH_DIU 0xC + +/* LDI/DVI Encoder for display */ +#define CONFIG_SYS_I2C_LDI_ADDR 0x38 +#define CONFIG_SYS_I2C_DVI_ADDR 0x75 /* * RTC configuration @@ -704,6 +728,7 @@ unsigned long get_board_ddr_clk(void); "bank_intlv=cs0_cs1;" \ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ + "video-mode=fslfb:1024x768-32@60,monitor=dvi\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ "tftpflash=tftpboot $loadaddr $uboot && " \ -- 1.7.4.1

2 1

[U-Boot] [PATCH 1/2] powerpc/mpc85xx: Add SCFG_PIXCLKCR register support for T1040
by Priyanka Jain 08 Mar '14

08 Mar '14

T1040 SoC has SCFG (Supplement Configuration) Block which provides chip specific configuration and status support. The base address of SCFG block in T1040 is 0xfc000. SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register) at offset 0x28. Add definition of -SCFG block -SCFG_PIXCLKCR register -Bits definition of SCFG_PIXCLK register Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> --- arch/powerpc/include/asm/immap_85xx.h | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 9d08321..0251265 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -1770,6 +1770,10 @@ defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022) #define FSL_CORENET_RCWSR13_MAC2_GMII_SEL 0x00000080 #define FSL_CORENET_RCWSR13_MAC2_GMII_SEL_L2_SWITCH 0x00000000 #define FSL_CORENET_RCWSR13_MAC2_GMII_SEL_ENET_PORT 0x80000000 +#define CONFIG_SYS_FSL_SCFG_PIXCLKCR_OFFSET 0x28 +#define PXCKEN_MASK 0x80000000 +#define PXCK_MASK 0x00FF0000 +#define PXCK_BITS_START 16 #elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081) #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xff000000 #define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24 @@ -2845,6 +2849,7 @@ struct ccsr_pman { #define CONFIG_SYS_FSL_CORENET_SERDES_OFFSET 0xEA000 #define CONFIG_SYS_FSL_CORENET_SERDES2_OFFSET 0xEB000 #define CONFIG_SYS_FSL_CPC_OFFSET 0x10000 +#define CONFIG_SYS_FSL_SCFG_OFFSET 0xFC000 #define CONFIG_SYS_MPC85xx_DMA1_OFFSET 0x100000 #define CONFIG_SYS_MPC85xx_DMA2_OFFSET 0x101000 #define CONFIG_SYS_MPC85xx_DMA3_OFFSET 0x102000 @@ -2962,6 +2967,10 @@ struct ccsr_pman { #define CONFIG_SYS_FSL_CPC_ADDR \ (CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_CPC_OFFSET) +#define CONFIG_SYS_FSL_SCFG_ADDR \ + (CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_SCFG_OFFSET) +#define CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR \ + (CONFIG_SYS_FSL_SCFG_ADDR + CONFIG_SYS_FSL_SCFG_PIXCLKCR_OFFSET) #define CONFIG_SYS_FSL_QMAN_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_FSL_QMAN_OFFSET) #define CONFIG_SYS_FSL_BMAN_ADDR \ -- 1.7.4.1

2 1

[U-Boot] [PATCH v2] powerpc/usb: Workaround for erratum-A006261
by Suresh Gupta 07 Mar '14

07 Mar '14

USB spec says that the minimum disconnect threshold should be over 525 mV. However, internal USB PHY threshold value is below this specified value. Due to this some devices disconnect at run-time. Hence, phy settings are tweaked to increased disconnect threshold to be above 525mV by using this workaround. Signed-off-by: Suresh Gupta <suresh.gupta(a)freescale.com> --- Changes for v2: - Incorporated missing SOC's affected by errata arch/powerpc/cpu/mpc85xx/cmd_errata.c | 4 ++ arch/powerpc/cpu/mpc85xx/cpu_init.c | 62 +++++++++++++++++++++++++++++++ arch/powerpc/include/asm/config_mpc85xx.h | 7 ++++ arch/powerpc/include/asm/fsl_errata.h | 34 +++++++++++++++++ include/fsl_usb.h | 23 +++++++++++- 5 files changed, 128 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 7693899..2a15802 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -265,6 +265,10 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) (SVR_REV(svr) <= CONFIG_SYS_FSL_A004447_SVR_REV)) puts("Work-around for Erratum I2C-A004447 enabled\n"); #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A006261 + if (has_erratum_a006261()) + puts("Work-around for Erratum A006261 enabled\n"); +#endif return 0; } diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index b31efb7..81aeadd 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -36,6 +36,54 @@ DECLARE_GLOBAL_DATA_PTR; +#ifdef CONFIG_SYS_FSL_ERRATUM_A006261 +void fsl_erratum_a006261_workaround(struct ccsr_usb_phy __iomem *usb_phy) +{ +#ifdef CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE + u32 xcvrprg = in_be32(&usb_phy->port1.xcvrprg); + + /* Increase Disconnect Threshold by 50mV */ + xcvrprg &= ~CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_MASK | + INC_DCNT_THRESHOLD_50MV; + /* Enable programming of USB High speed Disconnect threshold */ + xcvrprg |= CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_EN; + out_be32(&usb_phy->port1.xcvrprg, xcvrprg); + + xcvrprg = in_be32(&usb_phy->port2.xcvrprg); + /* Increase Disconnect Threshold by 50mV */ + xcvrprg &= ~CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_MASK | + INC_DCNT_THRESHOLD_50MV; + /* Enable programming of USB High speed Disconnect threshold */ + xcvrprg |= CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_EN; + out_be32(&usb_phy->port2.xcvrprg, xcvrprg); +#else + + u32 temp = 0; + u32 status = in_be32(&usb_phy->status1); + + u32 squelch_prog_rd_0_2 = + (status >> CONFIG_SYS_FSL_USB_SQUELCH_PROG_RD_0) + & CONFIG_SYS_FSL_USB_SQUELCH_PROG_MASK; + + u32 squelch_prog_rd_3_5 = + (status >> CONFIG_SYS_FSL_USB_SQUELCH_PROG_RD_3) + & CONFIG_SYS_FSL_USB_SQUELCH_PROG_MASK; + + setbits_be32(&usb_phy->config1, + CONFIG_SYS_FSL_USB_HS_DISCNCT_INC); + setbits_be32(&usb_phy->config2, + CONFIG_SYS_FSL_USB_RX_AUTO_CAL_RD_WR_SEL); + + temp = squelch_prog_rd_0_2 << CONFIG_SYS_FSL_USB_SQUELCH_PROG_WR_0; + out_be32(&usb_phy->config2, in_be32(&usb_phy->config2) | temp); + + temp = squelch_prog_rd_3_5 << CONFIG_SYS_FSL_USB_SQUELCH_PROG_WR_3; + out_be32(&usb_phy->config2, in_be32(&usb_phy->config2) | temp); +#endif +} +#endif + + #ifdef CONFIG_QE extern qe_iop_conf_t qe_iop_conf_tab[]; extern void qe_config_iopin(u8 port, u8 pin, int dir, @@ -625,6 +673,10 @@ skip_l2: { struct ccsr_usb_phy __iomem *usb_phy1 = (void *)CONFIG_SYS_MPC85xx_USB1_PHY_ADDR; +#ifdef CONFIG_SYS_FSL_ERRATUM_A006261 + if (has_erratum_a006261()) + fsl_erratum_a006261_workaround(usb_phy1); +#endif out_be32(&usb_phy1->usb_enable_override, CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE); } @@ -633,6 +685,10 @@ skip_l2: { struct ccsr_usb_phy __iomem *usb_phy2 = (void *)CONFIG_SYS_MPC85xx_USB2_PHY_ADDR; +#ifdef CONFIG_SYS_FSL_ERRATUM_A006261 + if (has_erratum_a006261()) + fsl_erratum_a006261_workaround(usb_phy2); +#endif out_be32(&usb_phy2->usb_enable_override, CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE); } @@ -672,8 +728,14 @@ skip_l2: CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN); setbits_be32(&usb_phy->port2.pwrfltcfg, CONFIG_SYS_FSL_USB_PWRFLT_CR_EN); + +#ifdef CONFIG_SYS_FSL_ERRATUM_A006261 + if (has_erratum_a006261()) + fsl_erratum_a006261_workaround(usb_phy); #endif +#endif /* CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE */ + #ifdef CONFIG_FMAN_ENET fman_enet_init(); #endif diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 56587ae..844e0dd 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -154,6 +154,7 @@ #define CONFIG_SYS_FSL_ERRATUM_IFC_A003399 #define CONFIG_SYS_FSL_ERRATUM_A005125 #define CONFIG_SYS_FSL_ERRATUM_I2C_A004447 +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_FSL_A004447_SVR_REV 0x10 #define CONFIG_ESDHC_HC_BLK_ADDR @@ -386,6 +387,7 @@ #define CONFIG_SYS_FSL_ERRATUM_SRIO_A004034 #define CONFIG_SYS_FSL_ERRATUM_A004849 #define CONFIG_SYS_FSL_ERRATUM_I2C_A004447 +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_FSL_A004447_SVR_REV 0x11 #elif defined(CONFIG_PPC_P3041) @@ -424,6 +426,7 @@ #define CONFIG_SYS_FSL_ERRATUM_A004849 #define CONFIG_SYS_FSL_ERRATUM_A005812 #define CONFIG_SYS_FSL_ERRATUM_I2C_A004447 +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_FSL_A004447_SVR_REV 0x20 #elif defined(CONFIG_PPC_P4080) /* also supports P4040 */ @@ -507,6 +510,7 @@ #define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xc0000000 #define CONFIG_SYS_FSL_ERRATUM_SRIO_A004034 #define CONFIG_SYS_FSL_ERRATUM_I2C_A004447 +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_FSL_A004447_SVR_REV 0x20 #elif defined(CONFIG_PPC_P5040) @@ -538,6 +542,7 @@ #define CONFIG_SYS_FSL_ERRATUM_A004699 #define CONFIG_SYS_FSL_ERRATUM_A004510 #define CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV 0x10 +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 0xf0000000 #define CONFIG_SYS_FSL_ERRATUM_A005812 @@ -633,6 +638,7 @@ #define CONFIG_SYS_FSL_ERRATUM_A004468 #define CONFIG_SYS_FSL_ERRATUM_A_004934 #define CONFIG_SYS_FSL_ERRATUM_A005871 +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_FSL_ERRATUM_A006379 #define CONFIG_SYS_FSL_ERRATUM_A006593 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 @@ -722,6 +728,7 @@ defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022) #define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4" #define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE #define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY +#define CONFIG_SYS_FSL_ERRATUM_A006261 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081) diff --git a/arch/powerpc/include/asm/fsl_errata.h b/arch/powerpc/include/asm/fsl_errata.h index a590919..c9982cc 100644 --- a/arch/powerpc/include/asm/fsl_errata.h +++ b/arch/powerpc/include/asm/fsl_errata.h @@ -26,4 +26,38 @@ static inline bool has_erratum_a006379(void) } #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A006261 +static inline bool has_erratum_a006261(void) +{ + u32 svr = get_svr(); + u32 soc = SVR_SOC_VER(svr); + + switch (soc) { + case SVR_P1010: + return IS_SVR_REV(svr, 1, 0) || IS_SVR_REV(svr, 2, 0); + case SVR_P2041: + case SVR_P2040: + return IS_SVR_REV(svr, 1, 0) || + IS_SVR_REV(svr, 1, 1) || IS_SVR_REV(svr, 2, 1); + case SVR_P3041: + return IS_SVR_REV(svr, 1, 0) || + IS_SVR_REV(svr, 1, 1) || + IS_SVR_REV(svr, 2, 0) || IS_SVR_REV(svr, 2, 1); + case SVR_P5010: + case SVR_P5020: + case SVR_P5021: + return IS_SVR_REV(svr, 1, 0) || IS_SVR_REV(svr, 2, 0); + case SVR_T4240: + case SVR_T4160: + return IS_SVR_REV(svr, 1, 0) || IS_SVR_REV(svr, 2, 0); + case SVR_T1040: + return IS_SVR_REV(svr, 1, 0); + case SVR_P5040: + return IS_SVR_REV(svr, 1, 0); + } + + return false; +} +#endif + #endif diff --git a/include/fsl_usb.h b/include/fsl_usb.h index 915774c..8b63cdd 100644 --- a/include/fsl_usb.h +++ b/include/fsl_usb.h @@ -52,13 +52,32 @@ struct ccsr_usb_phy { #define CONFIG_SYS_FSL_USB_PLLPRG2_MFI (5 << 16) #define CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN (1 << 21) #define CONFIG_SYS_FSL_USB_SYS_CLK_VALID (1 << 0) +#define CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_EN (1 << 7) +#define CONFIG_SYS_FSL_USB_XCVRPRG_HS_DCNT_PROG_MASK (3 << 4) + +#define INC_DCNT_THRESHOLD_25MV (0 << 4) +#define INC_DCNT_THRESHOLD_50MV (1 << 4) +#define DEC_DCNT_THRESHOLD_25MV (2 << 4) +#define DEC_DCNT_THRESHOLD_50MV (3 << 4) #else struct ccsr_usb_phy { - u8 res0[0x18]; + u32 config1; + u32 config2; + u32 config3; + u32 config4; + u32 config5; + u32 status1; u32 usb_enable_override; u8 res[0xe4]; }; -#define CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE 1 +#define CONFIG_SYS_FSL_USB_HS_DISCNCT_INC (3 << 22) +#define CONFIG_SYS_FSL_USB_RX_AUTO_CAL_RD_WR_SEL (1 << 20) +#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_WR_0 13 +#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_WR_3 16 +#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_RD_0 0 +#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_RD_3 3 +#define CONFIG_SYS_FSL_USB_ENABLE_OVERRIDE 1 +#define CONFIG_SYS_FSL_USB_SQUELCH_PROG_MASK 0x07 #endif #endif /*_ASM_FSL_USB_H_ */ -- 1.7.11.7

2 1

[U-Boot] [PATCH] powerpc/b4860: Add workaround for errata A006384 and A006475
by Shaveta Leekha 07 Mar '14

07 Mar '14

SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384) and at cold temperatures(A006475), workaround recalibrate the PLLs with some SerDes configuration Both these errata are only applicable for b4 rev1. So, make workaround for these errata conditional, depending upon soc version. Signed-off-by: Shaveta Leekha <shaveta(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/cmd_errata.c | 8 ++ arch/powerpc/include/asm/config_mpc85xx.h | 2 + arch/powerpc/include/asm/immap_85xx.h | 19 +++- board/freescale/b4860qds/b4860qds.c | 193 +++++++++++++++++++++++++++++ 4 files changed, 220 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c index 7693899..d0a1c51 100644 --- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c +++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c @@ -229,6 +229,14 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) if (IS_SVR_REV(svr, 1, 0)) puts("Work-around for Erratum A005871 enabled\n"); #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A006475 + if (SVR_MAJ(get_svr()) == 1) + puts("Work-around for Erratum A006475 enabled\n"); +#endif +#ifdef CONFIG_SYS_FSL_ERRATUM_A006384 + if (SVR_MAJ(get_svr()) == 1) + puts("Work-around for Erratum A006384 enabled\n"); +#endif #ifdef CONFIG_SYS_FSL_ERRATUM_A004849 /* This work-around is implemented in PBI, so just check for it */ check_erratum_a4849(svr); diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 0ec1417..2f47b3f 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -662,6 +662,8 @@ #define CONFIG_SYS_FSL_ERRATUM_A005871 #define CONFIG_SYS_FSL_ERRATUM_A006379 #define CONFIG_SYS_FSL_ERRATUM_A006593 +#define CONFIG_SYS_FSL_ERRATUM_A006475 +#define CONFIG_SYS_FSL_ERRATUM_A006384 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000 #ifdef CONFIG_PPC_B4860 diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index e0efc7e..edd7888 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -2495,6 +2495,7 @@ typedef struct serdes_corenet { #define SRDS_RSTCTL_SDEN 0x00000020 #define SRDS_RSTCTL_SDRST_B 0x00000040 #define SRDS_RSTCTL_PLLRST_B 0x00000080 +#define SRDS_RSTCTL_RSTERR_SHIFT 29 u32 pllcr0; /* PLL Control Register 0 */ #define SRDS_PLLCR0_POFF 0x80000000 #define SRDS_PLLCR0_RFCK_SEL_MASK 0x70000000 @@ -2504,6 +2505,7 @@ typedef struct serdes_corenet { #define SRDS_PLLCR0_RFCK_SEL_150 0x30000000 #define SRDS_PLLCR0_RFCK_SEL_161_13 0x40000000 #define SRDS_PLLCR0_RFCK_SEL_122_88 0x50000000 +#define SRDS_PLLCR0_DCBIAS_OUT_EN 0x02000000 #define SRDS_PLLCR0_FRATE_SEL_MASK 0x000f0000 #define SRDS_PLLCR0_FRATE_SEL_5 0x00000000 #define SRDS_PLLCR0_FRATE_SEL_3_75 0x00050000 @@ -2511,9 +2513,22 @@ typedef struct serdes_corenet { #define SRDS_PLLCR0_FRATE_SEL_4 0x00070000 #define SRDS_PLLCR0_FRATE_SEL_3_12 0x00090000 #define SRDS_PLLCR0_FRATE_SEL_3 0x000a0000 +#define SRDS_PLLCR0_DCBIAS_OVRD 0x000000F0 +#define SRDS_PLLCR0_DCBIAS_OVRD_SHIFT 4 u32 pllcr1; /* PLL Control Register 1 */ -#define SRDS_PLLCR1_PLL_BWSEL 0x08000000 - u32 res_0c; /* 0x00c */ +#define SRDS_PLLCR1_BCAP_EN 0x20000000 +#define SRDS_PLLCR1_BCAP_OVD 0x10000000 +#define SRDS_PLLCR1_PLL_FCAP 0x001F8000 +#define SRDS_PLLCR1_PLL_FCAP_SHIFT 15 +#define SRDS_PLLCR1_PLL_BWSEL 0x08000000 +#define SRDS_PLLCR1_BYP_CAL 0x02000000 + u32 pllsr2; /* At 0x00c, PLL Status Register 2 */ +#define SRDS_PLLSR2_BCAP_EN 0x00800000 +#define SRDS_PLLSR2_BCAP_EN_SHIFT 23 +#define SRDS_PLLSR2_FCAP 0x003F0000 +#define SRDS_PLLSR2_FCAP_SHIFT 16 +#define SRDS_PLLSR2_DCBIAS 0x000F0000 +#define SRDS_PLLSR2_DCBIAS_SHIFT 16 u32 pllcr3; u32 pllcr4; u8 res_18[0x20-0x18]; diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 15b3f62..264d8c7 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -286,6 +286,182 @@ int configure_vsc3316_3308(void) return 0; } +static int calibrate_pll(serdes_corenet_t *srds_regs, int pll_num) +{ + u32 rst_err; + + /* Steps For SerDes PLLs reset and reconfiguration + * or PLL power-up procedure + */ + debug("CALIBRATE PLL:%d\n", pll_num); + clrbits_be32(&srds_regs->bank[pll_num].rstctl, + SRDS_RSTCTL_SDRST_B); + udelay(10); + clrbits_be32(&srds_regs->bank[pll_num].rstctl, + (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B)); + udelay(10); + setbits_be32(&srds_regs->bank[pll_num].rstctl, + SRDS_RSTCTL_RST); + setbits_be32(&srds_regs->bank[pll_num].rstctl, + (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B + | SRDS_RSTCTL_SDRST_B)); + + udelay(20); + + /* Check whether PLL has been locked or not */ + rst_err = in_be32(&srds_regs->bank[pll_num].rstctl) & + SRDS_RSTCTL_RSTERR; + rst_err >>= SRDS_RSTCTL_RSTERR_SHIFT; + debug("RST_ERR value for PLL %d is: 0x%x:\n", pll_num, rst_err); + if (rst_err) + return rst_err; + + return rst_err; +} + +static int check_pll_locks(serdes_corenet_t *srds_regs, int pll_num) +{ + int ret = 0; + u32 fcap, dcbias, bcap, pllcr1, pllcr0; + + if (calibrate_pll(srds_regs, pll_num)) { + /* STEP 1 */ + /* Read fcap, dcbias and bcap value */ + clrbits_be32(&srds_regs->bank[pll_num].pllcr0, + SRDS_PLLCR0_DCBIAS_OUT_EN); + fcap = in_be32(&srds_regs->bank[pll_num].pllsr2) & + SRDS_PLLSR2_FCAP; + fcap >>= SRDS_PLLSR2_FCAP_SHIFT; + bcap = in_be32(&srds_regs->bank[pll_num].pllsr2) & + SRDS_PLLSR2_BCAP_EN; + bcap >>= SRDS_PLLSR2_BCAP_EN_SHIFT; + setbits_be32(&srds_regs->bank[pll_num].pllcr0, + SRDS_PLLCR0_DCBIAS_OUT_EN); + dcbias = in_be32(&srds_regs->bank[pll_num].pllsr2) & + SRDS_PLLSR2_DCBIAS; + dcbias >>= SRDS_PLLSR2_DCBIAS_SHIFT; + debug("values of bcap:%x, fcap:%x and dcbias:%x\n", + bcap, fcap, dcbias); + if (fcap == 0 && bcap == 1) { + /* Step 3 */ + clrbits_be32(&srds_regs->bank[pll_num].rstctl, + (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B + | SRDS_RSTCTL_SDRST_B)); + clrbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BCAP_EN); + setbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BCAP_OVD); + if (calibrate_pll(srds_regs, pll_num)) { + /*save the fcap, dcbias and bcap values*/ + clrbits_be32(&srds_regs->bank[pll_num].pllcr0, + SRDS_PLLCR0_DCBIAS_OUT_EN); + fcap = in_be32(&srds_regs->bank[pll_num].pllsr2) + & SRDS_PLLSR2_FCAP; + fcap >>= SRDS_PLLSR2_FCAP_SHIFT; + bcap = in_be32(&srds_regs->bank[pll_num].pllsr2) + & SRDS_PLLSR2_BCAP_EN; + bcap >>= SRDS_PLLSR2_BCAP_EN_SHIFT; + setbits_be32(&srds_regs->bank[pll_num].pllcr0, + SRDS_PLLCR0_DCBIAS_OUT_EN); + dcbias = in_be32 + (&srds_regs->bank[pll_num].pllsr2) & + SRDS_PLLSR2_DCBIAS; + dcbias >>= SRDS_PLLSR2_DCBIAS_SHIFT; + + /* Step 4*/ + clrbits_be32(&srds_regs->bank[pll_num].rstctl, + (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B + | SRDS_RSTCTL_SDRST_B)); + setbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BYP_CAL); + clrbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BCAP_EN); + setbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BCAP_OVD); + /* change the fcap and dcbias to the saved + * values from Step 3 */ + clrbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_PLL_FCAP); + pllcr1 = (in_be32 + (&srds_regs->bank[pll_num].pllcr1)| + (fcap << SRDS_PLLCR1_PLL_FCAP_SHIFT)); + out_be32(&srds_regs->bank[pll_num].pllcr1, + pllcr1); + clrbits_be32(&srds_regs->bank[pll_num].pllcr0, + SRDS_PLLCR0_DCBIAS_OVRD); + pllcr0 = (in_be32 + (&srds_regs->bank[pll_num].pllcr0)| + (dcbias << SRDS_PLLCR0_DCBIAS_OVRD_SHIFT)); + out_be32(&srds_regs->bank[pll_num].pllcr0, + pllcr0); + ret = calibrate_pll(srds_regs, pll_num); + if (ret) + return ret; + } else { + goto out; + } + } else { /* Step 5 */ + clrbits_be32(&srds_regs->bank[pll_num].rstctl, + (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B + | SRDS_RSTCTL_SDRST_B)); + udelay(10); + /* Change the fcap, dcbias, and bcap to the + * values from Step 1 */ + setbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BYP_CAL); + clrbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_PLL_FCAP); + pllcr1 = (in_be32(&srds_regs->bank[pll_num].pllcr1)| + (fcap << SRDS_PLLCR1_PLL_FCAP_SHIFT)); + out_be32(&srds_regs->bank[pll_num].pllcr1, + pllcr1); + clrbits_be32(&srds_regs->bank[pll_num].pllcr0, + SRDS_PLLCR0_DCBIAS_OVRD); + pllcr0 = (in_be32(&srds_regs->bank[pll_num].pllcr0)| + (dcbias << SRDS_PLLCR0_DCBIAS_OVRD_SHIFT)); + out_be32(&srds_regs->bank[pll_num].pllcr0, + pllcr0); + clrbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BCAP_EN); + setbits_be32(&srds_regs->bank[pll_num].pllcr1, + SRDS_PLLCR1_BCAP_OVD); + ret = calibrate_pll(srds_regs, pll_num); + if (ret) + return ret; + } + } +out: + return 0; +} + +static int check_serdes_pll_locks(void) +{ + serdes_corenet_t *srds1_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + serdes_corenet_t *srds2_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES2_ADDR; + int i, ret1, ret2; + + debug("\nSerDes1 Lock check\n"); + for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { + ret1 = check_pll_locks(srds1_regs, i); + if (ret1) { + printf("SerDes1, PLL:%d didnt lock\n", i); + return ret1; + } + } + debug("\nSerDes2 Lock check\n"); + for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { + ret2 = check_pll_locks(srds2_regs, i); + if (ret2) { + printf("SerDes2, PLL:%d didnt lock\n", i); + return ret2; + } + } + + return 0; +} + int config_serdes1_refclks(void) { ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); @@ -476,6 +652,8 @@ int config_serdes2_refclks(void) setbits_be32(&srds2_regs->bank[i].rstctl, (SRDS_RSTCTL_SDEN | SRDS_RSTCTL_PLLRST_B | SRDS_RSTCTL_SDRST_B)); + + udelay(10); } break; default: @@ -542,6 +720,21 @@ int board_early_init_r(void) else printf("SerDes2 Refclk reconfiguring failed.\n"); +#if defined(CONFIG_SYS_FSL_ERRATUM_A006384) || \ + defined(CONFIG_SYS_FSL_ERRATUM_A006475) + /* Rechecking the SerDes locks after all SerDes configurations + * are done, As SerDes PLLs may not lock reliably at 5 G VCO + * and at cold temperatures. + * Following sequence ensure the proper locking of SerDes PLLs. + */ + if (SVR_MAJ(get_svr()) == 1) { + if (check_serdes_pll_locks()) + printf("SerDes plls still not locked properly.\n"); + else + printf("SerDes plls have been locked well.\n"); + } +#endif + /* Configure VSC3316 and VSC3308 crossbar switches */ if (configure_vsc3316_3308()) printf("VSC:failed to configure VSC3316/3308.\n"); -- 1.7.6.GIT

2 1

[U-Boot] [PATCH 2/2] B4860qds: Set SerDes2 refclk2 at to 156.25MHz for XFI to work
by Shaveta Leekha 07 Mar '14

07 Mar '14

- Change setting of SerDes2 refclk2 to have the default value as it is coming on board that is 156.25MHz, for XFI to work - Also change PLL_NUM variable to the one defined in config_mpc85xx.h for B4860 and B4420 Signed-off-by: Shaveta Leekha <shaveta(a)freescale.com> --- board/freescale/b4860qds/b4860qds.c | 7 +++---- 1 files changed, 3 insertions(+), 4 deletions(-) diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index 9d51864..15b3f62 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -29,7 +29,6 @@ #define CLK_MUX_SEL_MASK 0x4 #define ETH_PHY_CLK_OUT 0x4 -#define PLL_NUM 2 DECLARE_GLOBAL_DATA_PTR; @@ -384,7 +383,7 @@ int config_serdes1_refclks(void) /* Steps For SerDes PLLs reset and reconfiguration after * changing SerDes's refclks */ - for (i = 0; i < PLL_NUM; i++) { + for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { debug("For PLL%d reset and reconfiguration after" " changing refclks\n", i+1); clrbits_be32(&srds_regs->bank[i].rstctl, @@ -451,7 +450,7 @@ int config_serdes2_refclks(void) if (!ret) { ret = set_serdes_refclk(IDT_SERDES2_ADDRESS, 2, SERDES_REFCLK_100, - SERDES_REFCLK_100, 0); + SERDES_REFCLK_156_25, 0); if (ret) { printf("IDT8T49N222A configuration failed.\n"); goto out; @@ -465,7 +464,7 @@ int config_serdes2_refclks(void) /* Steps For SerDes PLLs reset and reconfiguration after * changing SerDes's refclks */ - for (i = 0; i < PLL_NUM; i++) { + for (i = 0; i < CONFIG_SYS_FSL_SRDS_NUM_PLLS; i++) { clrbits_be32(&srds2_regs->bank[i].rstctl, SRDS_RSTCTL_SDRST_B); udelay(10); -- 1.7.6.GIT

2 1

[U-Boot] [PATCH 1/2] B4860/B4420: Add PLL_NUM define for B4420/B4860 to use SerDes2 Refclks re-configuration
by Shaveta Leekha 07 Mar '14

07 Mar '14

- B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes, add their defines in arch/powerpc/include/asm/config_mpc85xx.h Signed-off-by: Shaveta Leekha <shaveta(a)freescale.com> --- arch/powerpc/include/asm/config_mpc85xx.h | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h index 56587ae..0ec1417 100644 --- a/arch/powerpc/include/asm/config_mpc85xx.h +++ b/arch/powerpc/include/asm/config_mpc85xx.h @@ -667,6 +667,7 @@ #ifdef CONFIG_PPC_B4860 #define CONFIG_SYS_FSL_CORES_PER_CLUSTER 4 #define CONFIG_MAX_CPUS 4 +#define CONFIG_SYS_FSL_SRDS_NUM_PLLS 2 #define CONFIG_SYS_FSL_NUM_CC_PLLS 4 #define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 4, 4, 4 } #define CONFIG_SYS_NUM_FM1_DTSEC 6 @@ -679,6 +680,7 @@ #define CONFIG_SYS_FSL_SRIO_LIODN #else #define CONFIG_MAX_CPUS 2 +#define CONFIG_SYS_FSL_SRDS_NUM_PLLS 1 #define CONFIG_SYS_FSL_CORES_PER_CLUSTER 2 #define CONFIG_SYS_FSL_NUM_CC_PLLS 4 #define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 4 } -- 1.7.6.GIT

2 1

[U-Boot] [PATCH] 85xx/b4860: Alternate serdes protocols for B4860/B4420
by Poonam Aggrwal 07 Mar '14

07 Mar '14

On B4860 and B4420, some serdes protocols can be used with LC VCO as well as Ring VCO options. Addded Alternate options with LC VCO for such protocols. For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO. The alternate option has the same functionality as the original option; the only difference being LC VCO rather than Ring VCO. Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/b4860_serdes.c | 29 +++++++++++++++++++++++++++++ board/freescale/b4860qds/b4860qds.c | 2 ++ board/freescale/b4860qds/eth_b4860qds.c | 5 +++++ 3 files changed, 36 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/b4860_serdes.c b/arch/powerpc/cpu/mpc85xx/b4860_serdes.c index 6ff6a70..d7b5950 100644 --- a/arch/powerpc/cpu/mpc85xx/b4860_serdes.c +++ b/arch/powerpc/cpu/mpc85xx/b4860_serdes.c @@ -24,6 +24,8 @@ static struct serdes_config serdes1_cfg_tbl[] = { CPRI4, CPRI3, CPRI2, CPRI1}}, {0x12, {CPRI8, CPRI7, CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1}}, + {0x29, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, + CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1} }, {0x2a, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1}}, {0x2C, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, @@ -32,6 +34,9 @@ static struct serdes_config serdes1_cfg_tbl[] = { CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1}}, {0x2E, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, CPRI6, CPRI5, CPRI4, CPRI3, CPRI2, CPRI1}}, + {0x2F, {AURORA, AURORA, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + CPRI4, CPRI3, CPRI2, CPRI1} }, {0x30, {AURORA, AURORA, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, CPRI4, CPRI3, CPRI2, CPRI1}}, @@ -50,12 +55,18 @@ static struct serdes_config serdes1_cfg_tbl[] = { }; static struct serdes_config serdes2_cfg_tbl[] = { /* SerDes 2 */ + {0x17, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + AURORA, AURORA, SRIO1, SRIO1} }, {0x18, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, AURORA, AURORA, SRIO1, SRIO1}}, {0x1D, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, AURORA, AURORA, SRIO1, SRIO1}}, + {0x2A, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SRIO2, SRIO2, + AURORA, AURORA, SRIO1, SRIO1} }, {0x2B, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SRIO2, SRIO2, AURORA, AURORA, SRIO1, SRIO1}}, @@ -63,6 +74,9 @@ static struct serdes_config serdes2_cfg_tbl[] = { SRIO2, SRIO2, AURORA, AURORA, SRIO1, SRIO1}}, + {0x48, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SGMII_FM1_DTSEC3, AURORA, + SRIO1, SRIO1, SRIO1, SRIO1} }, {0x49, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, AURORA, SRIO1, SRIO1, SRIO1, SRIO1}}, @@ -75,18 +89,30 @@ static struct serdes_config serdes2_cfg_tbl[] = { {0x4E, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC3, AURORA, SRIO1, SRIO1, SRIO1, SRIO1}}, + {0x79, {SRIO2, SRIO2, SRIO2, SRIO2, + SRIO1, SRIO1, SRIO1, SRIO1} }, {0x7A, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1}}, + {0x83, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SRIO2, SRIO2, AURORA, AURORA, + XFI_FM1_MAC9, XFI_FM1_MAC10} }, {0x84, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SRIO2, SRIO2, AURORA, AURORA, XFI_FM1_MAC9, XFI_FM1_MAC10}}, {0x85, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SRIO2, SRIO2, AURORA, AURORA, XFI_FM1_MAC9, XFI_FM1_MAC10}}, + {0x86, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, + SRIO2, SRIO2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + XFI_FM1_MAC9, XFI_FM1_MAC10} }, {0x87, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, SRIO2, SRIO2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, XFI_FM1_MAC9, XFI_FM1_MAC10}}, + {0x8C, {SRIO2, SRIO2, SRIO2, SRIO2, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + XFI_FM1_MAC9, XFI_FM1_MAC10} }, {0x8D, {SRIO2, SRIO2, SRIO2, SRIO2, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, XFI_FM1_MAC9, XFI_FM1_MAC10}}, @@ -101,6 +127,9 @@ static struct serdes_config serdes2_cfg_tbl[] = { SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, XAUI_FM1_MAC10, XAUI_FM1_MAC10, XAUI_FM1_MAC10, XAUI_FM1_MAC10}}, + {0xB1, {PCIE1, PCIE1, PCIE1, PCIE1, + SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, + XFI_FM1_MAC9, XFI_FM1_MAC10} }, {0xB2, {PCIE1, PCIE1, PCIE1, PCIE1, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4, XFI_FM1_MAC9, XFI_FM1_MAC10}}, diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c index f6b012d..901c956 100644 --- a/board/freescale/b4860qds/b4860qds.c +++ b/board/freescale/b4860qds/b4860qds.c @@ -120,6 +120,7 @@ int configure_vsc3316_3308(void) debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl); switch (serdes1_prtcl) { + case 0x29: case 0x2a: case 0x2C: case 0x2D: @@ -152,6 +153,7 @@ int configure_vsc3316_3308(void) break; #ifdef CONFIG_PPC_B4420 + case 0x17: case 0x18: /* * Configuration: diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c index a8fc845..12df9a8 100644 --- a/board/freescale/b4860qds/eth_b4860qds.c +++ b/board/freescale/b4860qds/eth_b4860qds.c @@ -66,6 +66,7 @@ static void initialize_lane_to_slot(void) serdes2_prtcl); switch (serdes2_prtcl) { + case 0x17: case 0x18: /* * Configuration: @@ -198,6 +199,7 @@ int board_eth_init(bd_t *bis) fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); switch (serdes1_prtcl) { + case 0x29: case 0x2a: /* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */ debug("Setting phy addresses for FM1_DTSEC5: %x and" @@ -209,6 +211,7 @@ int board_eth_init(bd_t *bis) CONFIG_SYS_FM1_DTSEC6_PHY_ADDR); break; #ifdef CONFIG_PPC_B4420 + case 0x17: case 0x18: /* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */ debug("Setting phy addresses for FM1_DTSEC3: %x and" @@ -228,6 +231,7 @@ int board_eth_init(bd_t *bis) break; } switch (serdes2_prtcl) { + case 0x17: case 0x18: debug("Setting phy addresses on SGMII Riser card for" "FM1_DTSEC ports: \n"); @@ -240,6 +244,7 @@ int board_eth_init(bd_t *bis) fm_info_set_phy_address(FM1_DTSEC4, CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR); break; + case 0x48: case 0x49: debug("Setting phy addresses on SGMII Riser card for" "FM1_DTSEC ports: \n"); -- 1.7.4.1

2 1