January 2014 - U-Boot

[U-Boot] [PATCH v3] t2080qds/ddr: update ddr parameters
by Shengzhou Liu 22 Jan '14

22 Jan '14

- Optimize UDIMM parameters for whole range from 1500MT/s to 2140MT/s. - Remove unused patameters: 'cpo', 'wrdata delay', '2T', which are unrelated to DDR3/3L. Tested with UDIMM 9JSF25672AZ-2G1K1 and verified speed 1200/1866/2133MT/s. Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- v3: fix issue of two line with same parameters and add more commit description. v2: rebase. board/freescale/t2080qds/ddr.c | 12 ++------ board/freescale/t2080qds/ddr.h | 65 +++++++++++++++++------------------------- 2 files changed, 28 insertions(+), 49 deletions(-) diff --git a/board/freescale/t2080qds/ddr.c b/board/freescale/t2080qds/ddr.c index 5db5d21..ed1334d 100644 --- a/board/freescale/t2080qds/ddr.c +++ b/board/freescale/t2080qds/ddr.c @@ -24,7 +24,7 @@ void fsl_ddr_board_options(memctl_options_t *popts, const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; ulong ddr_freq; - if (ctrl_num > 2) { + if (ctrl_num > 1) { printf("Not supported controller number %d\n", ctrl_num); return; } @@ -40,8 +40,7 @@ void fsl_ddr_board_options(memctl_options_t *popts, else pbsp = udimms[0]; - - /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr * freqency and n_banks specified in board_specific_parameters table. */ ddr_freq = get_ddr_freq(0) / 1000000; @@ -49,14 +48,10 @@ void fsl_ddr_board_options(memctl_options_t *popts, if (pbsp->n_ranks == pdimm->n_ranks && (pdimm->rank_density >> 30) >= pbsp->rank_gb) { if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->cpo_override = pbsp->cpo; - popts->write_data_delay = - pbsp->write_data_delay; popts->clk_adjust = pbsp->clk_adjust; popts->wrlvl_start = pbsp->wrlvl_start; popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp->force_2t; goto found; } pbsp_highest = pbsp; @@ -69,13 +64,10 @@ void fsl_ddr_board_options(memctl_options_t *popts, printf("for data rate %lu MT/s\n", ddr_freq); printf("Trying to use the highest speed (%u) parameters\n", pbsp_highest->datarate_mhz_high); - popts->cpo_override = pbsp_highest->cpo; - popts->write_data_delay = pbsp_highest->write_data_delay; popts->clk_adjust = pbsp_highest->clk_adjust; popts->wrlvl_start = pbsp_highest->wrlvl_start; popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp_highest->force_2t; } else { panic("DIMM is not supported by this board"); } diff --git a/board/freescale/t2080qds/ddr.h b/board/freescale/t2080qds/ddr.h index 964eaad..9fc879a 100644 --- a/board/freescale/t2080qds/ddr.h +++ b/board/freescale/t2080qds/ddr.h @@ -14,9 +14,6 @@ struct board_specific_parameters { u32 wrlvl_start; u32 wrlvl_ctl_2; u32 wrlvl_ctl_3; - u32 cpo; - u32 write_data_delay; - u32 force_2t; }; /* @@ -28,58 +25,48 @@ struct board_specific_parameters { static const struct board_specific_parameters udimm0[] = { /* * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | */ - {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, - {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, - {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, - {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, - {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, - {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, - {1, 1800, 2, 5, 6, 0x06070709, 0x110a0b08, 0xff, 2, 0}, - {1, 1866, 2, 4, 6, 0x06060708, 0x09090a07, 0xff, 2, 0}, - {1, 1900, 2, 4, 6, 0x06060708, 0x09090a07, 0xff, 2, 0}, - {1, 2000, 2, 4, 8, 0x090a0b0d, 0x0e0f110b, 0xff, 2, 0}, - {1, 2133, 2, 4, 8, 0x090a0b0d, 0x0e0f110b, 0xff, 2, 0}, + {2, 1200, 2, 5, 7, 0x0808090a, 0x0b0c0c0a}, + {2, 1500, 2, 5, 6, 0x07070809, 0x0a0b0b09}, + {2, 1600, 2, 5, 8, 0x090b0b0d, 0x0d0e0f0b}, + {2, 1700, 2, 4, 7, 0x080a0a0c, 0x0c0d0e0a}, + {2, 1900, 2, 5, 9, 0x0a0b0c0e, 0x0f10120c}, + {2, 2140, 2, 4, 8, 0x090a0b0d, 0x0e0f110b}, + {1, 1200, 2, 5, 7, 0x0808090a, 0x0b0c0c0a}, + {1, 1500, 2, 5, 6, 0x07070809, 0x0a0b0b09}, + {1, 1600, 2, 5, 8, 0x090b0b0d, 0x0d0e0f0b}, + {1, 1700, 2, 4, 7, 0x080a0a0c, 0x0c0d0e0a}, + {1, 1900, 2, 5, 9, 0x0a0b0c0e, 0x0f10120c}, + {1, 2140, 2, 4, 8, 0x090a0b0d, 0x0e0f110b}, {} }; static const struct board_specific_parameters rdimm0[] = { /* * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | + * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | + * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | */ - {4, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0}, - {4, 1666, 0, 5, 11, 0x0a080706, 0x07090906, 0xff, 2, 0}, - {4, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0}, - {2, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0}, - {2, 1666, 0, 5, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0}, - {2, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0}, - {1, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0}, - {1, 1666, 0, 5, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0}, - {1, 2140, 0, 4, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0}, + /* TODO: need tuning these parameters if RDIMM is used */ + {4, 1350, 0, 5, 9, 0x08070605, 0x06070806}, + {4, 1666, 0, 5, 11, 0x0a080706, 0x07090906}, + {4, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07}, + {2, 1350, 0, 5, 9, 0x08070605, 0x06070806}, + {2, 1666, 0, 5, 11, 0x0a090806, 0x08090a06}, + {2, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07}, + {1, 1350, 0, 5, 9, 0x08070605, 0x06070806}, + {1, 1666, 0, 5, 11, 0x0a090806, 0x08090a06}, + {1, 2140, 0, 4, 12, 0x0b090807, 0x080a0b07}, {} }; -/* - * The three slots have slightly different timing. The center values are good - * for all slots. We use identical speed tables for them. In future use, if - * DIMMs require separated tables, make more entries as needed. - */ static const struct board_specific_parameters *udimms[] = { udimm0, }; -/* - * The three slots have slightly different timing. See comments above. - */ static const struct board_specific_parameters *rdimms[] = { rdimm0, }; - - #endif -- 1.8.0

2 1

[U-Boot] [PATCH] powerpc/85xx: update erratum a006379
by Shengzhou Liu 22 Jan '14

22 Jan '14

Enable Erratum A006379 for T2080, T2081, T4160, B4420. Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- arch/powerpc/include/asm/fsl_errata.h | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/powerpc/include/asm/fsl_errata.h b/arch/powerpc/include/asm/fsl_errata.h index 8af6751..507c9f5 100644 --- a/arch/powerpc/include/asm/fsl_errata.h +++ b/arch/powerpc/include/asm/fsl_errata.h @@ -29,7 +29,11 @@ static inline bool has_erratum_a006379(void) { u32 svr = get_svr(); if (((SVR_SOC_VER(svr) == SVR_T4240) && SVR_MAJ(svr) <= 1) || - ((SVR_SOC_VER(svr) == SVR_B4860) && SVR_MAJ(svr) <= 2)) + ((SVR_SOC_VER(svr) == SVR_T4160) && SVR_MAJ(svr) <= 1) || + ((SVR_SOC_VER(svr) == SVR_B4860) && SVR_MAJ(svr) <= 2) || + ((SVR_SOC_VER(svr) == SVR_B4420) && SVR_MAJ(svr) <= 2) || + ((SVR_SOC_VER(svr) == SVR_T2080) && SVR_MAJ(svr) <= 1) || + ((SVR_SOC_VER(svr) == SVR_T2081) && SVR_MAJ(svr) <= 1)) return true; return false; -- 1.8.0

2 1

[U-Boot] [PATCH v2] powerpc/t2080qds: some update for t2080qds
by Shengzhou Liu 21 Jan '14

21 Jan '14

- add more serdes protocols support. - fix some serdes lanes route. - fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d. - correct boot location info for SD/SPI boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu(a)freescale.com> --- v2: update to support more serdes, applied in Gerrit sdk. board/freescale/t2080qds/eth_t2080qds.c | 12 ++++-- board/freescale/t2080qds/t2080qds.c | 66 ++++++++++++++++++++++++++++++--- drivers/net/fm/t2080.c | 10 +++-- 3 files changed, 75 insertions(+), 13 deletions(-) diff --git a/board/freescale/t2080qds/eth_t2080qds.c b/board/freescale/t2080qds/eth_t2080qds.c index 9a909db..68d74c3 100644 --- a/board/freescale/t2080qds/eth_t2080qds.c +++ b/board/freescale/t2080qds/eth_t2080qds.c @@ -372,9 +372,11 @@ int board_eth_init(bd_t *bis) break; case 0x6c: case 0x6d: + fm_info_set_phy_address(FM1_10GEC1, 4); + fm_info_set_phy_address(FM1_10GEC2, 5); /* SGMII in Slot3 */ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR); - fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR); break; case 0x71: /* SGMII in Slot3 */ @@ -419,7 +421,6 @@ int board_eth_init(bd_t *bis) fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR); break; default: - puts("Invalid SerDes1 protocol for T2080QDS\n"); break; } @@ -449,7 +450,12 @@ int board_eth_init(bd_t *bis) fm_info_set_mdio(i, mii_dev_for_muxval( mdio_mux[i])); break; - }; + case 3: + mdio_mux[i] = EMI1_SLOT3; + fm_info_set_mdio(i, mii_dev_for_muxval( + mdio_mux[i])); + break; + } break; case PHY_INTERFACE_MODE_RGMII: if (i == FM1_DTSEC3) diff --git a/board/freescale/t2080qds/t2080qds.c b/board/freescale/t2080qds/t2080qds.c index cac32fe..4fe8ccb 100644 --- a/board/freescale/t2080qds/t2080qds.c +++ b/board/freescale/t2080qds/t2080qds.c @@ -40,6 +40,11 @@ int checkboard(void) printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4); printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1); +#ifdef CONFIG_SDCARD + puts("SD/MMC\n"); +#elif CONFIG_SPIFLASH + puts("SPI\n"); +#else sw = QIXIS_READ(brdcfg[0]); sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; @@ -51,6 +56,7 @@ int checkboard(void) puts("NAND\n"); else printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); +#endif printf("FPGA: v%d (%s), build %d", (int)QIXIS_READ(scver), qixis_read_tag(buf), (int)qixis_read_minor()); @@ -97,13 +103,25 @@ int brd_mux_lane_to_slot(void) /* SerDes1 is not enabled */ break; case 0x1c: - case 0x95: case 0xa2: - case 0x94: /* SD1(A:D) => SLOT3 SGMII * SD1(G:H) => SLOT1 SGMII */ - QIXIS_WRITE(brdcfg[12], 0x58); + QIXIS_WRITE(brdcfg[12], 0x1a); + break; + case 0x94: + case 0x95: + /* SD1(A:B) => SLOT3 SGMII(a)1.25bps + * SD1(C:D) => SFP Module, SGMII(a)3.125bps + * SD1(E:H) => SLOT1 SGMII(a)1.25bps + */ + case 0x96: + /* SD1(A:B) => SLOT3 SGMII(a)1.25bps + * SD1(C) => SFP Module, SGMII(a)3.125bps + * SD1(D) => SFP Module, SGMII(a)1.25bps + * SD1(E:H) => SLOT1 PCIe4 x4 + */ + QIXIS_WRITE(brdcfg[12], 0x3a); break; case 0x51: /* SD1(A:D) => SLOT3 XAUI @@ -134,6 +152,34 @@ int brd_mux_lane_to_slot(void) */ QIXIS_WRITE(brdcfg[12], 0xda); break; + case 0x6e: + /* SD1(A:B) => SFP Module, XFI + * SD1(C:D) => SLOT3 SGMII + * SD1(E:F) => SLOT1 PCIe4 x2 + * SD1(G:H) => SLOT2 SGMII + */ + QIXIS_WRITE(brdcfg[12], 0xd9); + break; + case 0xda: + /* SD1(A:H) => SLOT3 PCIe3 x8 + */ + QIXIS_WRITE(brdcfg[12], 0x0); + break; + case 0xc8: + /* SD1(A) => SLOT3 PCIe3 x1 + * SD1(B) => SFP Module, SGMII(a)1.25bps + * SD1(C:D) => SFP Module, SGMII(a)3.125bps + * SD1(E:F) => SLOT1 PCIe4 x2 + * SD1(G:H) => SLOT2 SGMII + */ + QIXIS_WRITE(brdcfg[12], 0x79); + break; + case 0xab: + /* SD1(A:D) => SLOT3 PCIe3 x4 + * SD1(E:H) => SLOT1 PCIe4 x4 + */ + QIXIS_WRITE(brdcfg[12], 0x1a); + break; default: printf("WARNING: unsupported for SerDes1 Protocol %d\n", srds_prtcl_s1); @@ -147,7 +193,7 @@ int brd_mux_lane_to_slot(void) case 0x01: case 0x02: /* SD2(A:H) => SLOT4 PCIe1 */ - QIXIS_WRITE(brdcfg[13], 0x20); + QIXIS_WRITE(brdcfg[13], 0x10); break; case 0x15: case 0x16: @@ -164,7 +210,7 @@ int brd_mux_lane_to_slot(void) * SD2(E:F) => SLOT5 Aurora * SD2(G:H) => SATA1,SATA2 */ - QIXIS_WRITE(brdcfg[13], 0x70); + QIXIS_WRITE(brdcfg[13], 0x78); break; case 0x1f: /* @@ -180,7 +226,15 @@ int brd_mux_lane_to_slot(void) * SD2(A:D) => SLOT4 SRIO2 * SD2(E:H) => SLOT5 SRIO1 */ - QIXIS_WRITE(brdcfg[13], 0x50); + QIXIS_WRITE(brdcfg[13], 0xa0); + break; + case 0x36: + /* + * SD2(A:D) => SLOT4 SRIO2 + * SD2(E:F) => Aurora + * SD2(G:H) => SATA1,SATA2 + */ + QIXIS_WRITE(brdcfg[13], 0x78); break; default: printf("WARNING: unsupported for SerDes2 Protocol %d\n", diff --git a/drivers/net/fm/t2080.c b/drivers/net/fm/t2080.c index b5c1e9f..3b6212f 100644 --- a/drivers/net/fm/t2080.c +++ b/drivers/net/fm/t2080.c @@ -50,15 +50,17 @@ phy_interface_t fman_port_enet_if(enum fm_port port) if (is_device_disabled(port)) return PHY_INTERFACE_MODE_NONE; - if ((port == FM1_10GEC1 || port == FM1_10GEC2 || - port == FM1_10GEC3 || port == FM1_10GEC4) && + if ((port == FM1_10GEC1 || port == FM1_10GEC2) && ((is_serdes_configured(XAUI_FM1_MAC9)) || - (is_serdes_configured(XFI_FM1_MAC1)) || - (is_serdes_configured(XFI_FM1_MAC2)) || (is_serdes_configured(XFI_FM1_MAC9)) || (is_serdes_configured(XFI_FM1_MAC10)))) return PHY_INTERFACE_MODE_XGMII; + if ((port == FM1_10GEC3 || port == FM1_10GEC4) && + ((is_serdes_configured(XFI_FM1_MAC1)) || + (is_serdes_configured(XFI_FM1_MAC2)))) + return PHY_INTERFACE_MODE_XGMII; + if ((port == FM1_DTSEC3) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) == FSL_CORENET_RCWSR13_EC1_DTSEC3_RGMII)) return PHY_INTERFACE_MODE_RGMII; -- 1.8.0

2 1

[U-Boot] [PATCH][v2] powerpc/83xx: Add support for get_svr() for 83xx devices
by Nikhil Badola 21 Jan '14

21 Jan '14

From: Ramneek Mehresh <ramneek.mehresh(a)freescale.com> Defines get_svr() for 83xx devices Signed-off-by: Ramneek Mehresh <ramneek.mehresh(a)freescale.com> --- Changes for v2: - Changed patch heading arch/powerpc/cpu/mpc83xx/start.S | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/powerpc/cpu/mpc83xx/start.S b/arch/powerpc/cpu/mpc83xx/start.S index b4fafe6..7f74a50 100644 --- a/arch/powerpc/cpu/mpc83xx/start.S +++ b/arch/powerpc/cpu/mpc83xx/start.S @@ -120,6 +120,11 @@ disable_addr_trans: mtspr SRR1, r3 rfi + .globl get_svr +get_svr: + mfspr r3, SVR + blr + .globl get_pvr get_pvr: mfspr r3, PVR -- 1.7.11.7

2 1

[U-Boot] [PATCH][v3] powerpc/t1040qds: Update DDR initialization related settings
by Priyanka Jain 21 Jan '14

21 Jan '14

Update following DDR related settings for T1040QDS -Correct number of chip selects to two as t1040qds supports two Chip selects. -Update board_specific_parameters udimm structure with settings derived via calibration. -Reduced I2C speed to 50KHz as DDR-SPD does not get reliably read at 400KHz. Verified the updated settings to be working fine with dual-ranked Micron, MT18KSF51272AZ-1G6 DIMM at data rate 833MT/s, 1333MT/s and 1600MT/s. Signed-off-by: Poonam Aggrwal <poonam.aggrwal(a)freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain(a)freescale.com> --- Changes for v3: Updated description based on York's comments. Changes for v2: Reduced I2C speed to 50KHz. board/freescale/t1040qds/ddr.h | 22 ++++++++++++---------- include/configs/T1040QDS.h | 6 +++--- 2 files changed, 15 insertions(+), 13 deletions(-) diff --git a/board/freescale/t1040qds/ddr.h b/board/freescale/t1040qds/ddr.h index 8ee206e..afa72af 100644 --- a/board/freescale/t1040qds/ddr.h +++ b/board/freescale/t1040qds/ddr.h @@ -31,16 +31,18 @@ static const struct board_specific_parameters udimm0[] = { * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | */ - {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, - {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, - {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, - {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, - {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, - {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, - {1, 1900, 0, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0}, - {1, 2140, 0, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {2, 833, 4, 4, 6, 0x06060607, 0x08080807, 0xff, 2, 0}, + {2, 833, 0, 4, 6, 0x06060607, 0x08080807, 0xff, 2, 0}, + {2, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09, 0xff, 2, 0}, + {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09, 0xff, 2, 0}, + {2, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A, 0xff, 2, 0}, + {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A, 0xff, 2, 0}, + {1, 833, 4, 4, 6, 0x06060607, 0x08080807, 0xff, 2, 0}, + {1, 833, 0, 4, 6, 0x06060607, 0x08080807, 0xff, 2, 0}, + {1, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09, 0xff, 2, 0}, + {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09, 0xff, 2, 0}, + {1, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A, 0xff, 2, 0}, + {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A, 0xff, 2, 0}, {} }; diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index 43a5778..484b237 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -167,7 +167,7 @@ unsigned long get_board_ddr_clk(void); /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ #define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) #define CONFIG_DDR_SPD #define CONFIG_SYS_FSL_DDR3 @@ -413,9 +413,9 @@ unsigned long get_board_ddr_clk(void); /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ -#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */ #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */ #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 -- 1.7.4.1

2 1

[U-Boot] [PATCH][v2] powerpc:Rename CONFIG_PBLRCW_CONFIG & CONFIG_SYS_FSL_PBL_PBI
by Prabhakar Kushwaha 21 Jan '14

21 Jan '14

Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG. Also add their details in README. Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> --- changes for v2: Incorporated Wolfgang's comments - Added more description in README Makefile | 4 ++-- README | 9 +++++++++ include/configs/B4860QDS.h | 4 ++-- include/configs/P2041RDB.h | 5 +++-- include/configs/T1040QDS.h | 4 ++-- include/configs/T2080QDS.h | 4 ++-- include/configs/T4240QDS.h | 4 ++-- include/configs/corenet_ds.h | 14 +++++++++----- include/configs/km/kmp204x-common.h | 4 ++-- 9 files changed, 33 insertions(+), 19 deletions(-) diff --git a/Makefile b/Makefile index e6f6edb..beee7ec 100644 --- a/Makefile +++ b/Makefile @@ -419,8 +419,8 @@ $(obj)u-boot.kwb: $(obj)u-boot.bin -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d $< $@ $(obj)u-boot.pbl: $(obj)u-boot.bin - $(obj)tools/mkimage -n $(CONFIG_PBLRCW_CONFIG) \ - -R $(CONFIG_PBLPBI_CONFIG) -T pblimage \ + $(obj)tools/mkimage -n $(CONFIG_SYS_FSL_PBL_RCW) \ + -R $(CONFIG_SYS_FSL_PBL_PBI) -T pblimage \ -d $< $@ $(obj)u-boot.sha1: $(obj)u-boot.bin diff --git a/README b/README index a0646c3..9b3aaf4 100644 --- a/README +++ b/README @@ -472,6 +472,15 @@ The following options need to be configured: Board config to use DDR3. It can be enabled for SoCs with Freescale DDR3 controllers. + CONFIG_SYS_FSL_PBL_PBI + It enables addition of RCW (Power on reset configuration) in built image. + Please refer doc/README.pblimage for more details + + CONFIG_SYS_FSL_PBL_RCW + It adds PBI(pre-boot instructions) commands in u-boot build image. + PBI commands can be used to configure SoC before it starts the execution. + Please refer doc/README.pblimage for more details + - Intel Monahans options: CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index c182158..c667229 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -16,8 +16,8 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg #endif #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index ee71252..2b81cbe 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -18,8 +18,9 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/corenet_ds/pbi.cfg -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p2041rdb.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/corenet_ds/pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW \ + $(SRCTREE)/board/freescale/corenet_ds/rcw_p2041rdb.cfg #endif #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index 7d0bc04..74d8049 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -32,8 +32,8 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg #endif /* High Level Configuration Options */ diff --git a/include/configs/T2080QDS.h b/include/configs/T2080QDS.h index bff001f..b35e107 100644 --- a/include/configs/T2080QDS.h +++ b/include/configs/T2080QDS.h @@ -45,8 +45,8 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg #endif #define CONFIG_SRIO_PCIE_BOOT_MASTER diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h index c96df54..1f1177b 100644 --- a/include/configs/T4240QDS.h +++ b/include/configs/T4240QDS.h @@ -21,8 +21,8 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg #endif #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index 969b990..3a1826d 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -15,15 +15,19 @@ #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/corenet_ds/pbi.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/corenet_ds/pbi.cfg #if defined(CONFIG_P3041DS) -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p3041ds.cfg +#define CONFIG_SYS_FSL_PBL_RCW \ + $(SRCTREE)/board/freescale/corenet_ds/rcw_p3041ds.cfg #elif defined(CONFIG_P4080DS) -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p4080ds.cfg +#define CONFIG_SYS_FSL_PBL_RCW \ + $(SRCTREE)/board/freescale/corenet_ds/rcw_p4080ds.cfg #elif defined(CONFIG_P5020DS) -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p5020ds.cfg +#define CONFIG_SYS_FSL_PBL_RCW \ + $(SRCTREE)/board/freescale/corenet_ds/rcw_p5020ds.cfg #elif defined(CONFIG_P5040DS) -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/corenet_ds/rcw_p5040ds.cfg +#define CONFIG_SYS_FSL_PBL_RCW \ + $(SRCTREE)/board/freescale/corenet_ds/rcw_p5040ds.cfg #endif #endif diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h index 50330cc..0463fcb 100644 --- a/include/configs/km/kmp204x-common.h +++ b/include/configs/km/kmp204x-common.h @@ -24,8 +24,8 @@ #define CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/keymile/kmp204x/pbi.cfg -#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg +#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/keymile/kmp204x/pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg /* High Level Configuration Options */ #define CONFIG_BOOKE -- 1.7.9.5

2 1

[U-Boot] [PATCH] powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL
by Po Liu 21 Jan '14

21 Jan '14

Using the TPL/SPL method to booting from 8k page NAND flash. - Add 4kB size tlb for minimal SPL image; - Add 256kB size SRAM tlb for second step booting; - Add spl.c for TPL image boot; - Add spl_minimal.c for minimal SPL image; - Add C291PCIE_NAND/C292PCIE_NAND/C293PCIE_NAND configure; - Modify C29XPCIE.h for nand config and enviroment; Signed-off-by: Po Liu <Po.Liu(a)freescale.com> --- arch/powerpc/cpu/mpc85xx/u-boot-spl.lds | 15 ++-- board/freescale/c29xpcie/Makefile | 15 ++++ board/freescale/c29xpcie/cpld.c | 2 + board/freescale/c29xpcie/spl.c | 73 ++++++++++++++++++ board/freescale/c29xpcie/spl_minimal.c | 63 ++++++++++++++++ board/freescale/c29xpcie/tlb.c | 22 +++++- boards.cfg | 1 + drivers/mtd/nand/fsl_ifc_spl.c | 29 +++++-- include/configs/C29XPCIE.h | 129 +++++++++++++++++++++++++++++++- 9 files changed, 330 insertions(+), 19 deletions(-) create mode 100644 board/freescale/c29xpcie/spl.c create mode 100644 board/freescale/c29xpcie/spl_minimal.c diff --git a/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds b/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds index bc13267..acaa093 100644 --- a/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds +++ b/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds @@ -57,7 +57,14 @@ SECTIONS . = ALIGN(8); __init_begin = .; __init_end = .; -/* FIXME for non-NAND SPL */ + +/* For ifc, elbc, esdhc, espi, all need the SPL without section .resetvec */ +#ifdef CONFIG_SYS_MPC85XX_NO_RESETVEC + .bootpg ADDR(.text) - 0x1000 : + { + KEEP(*(.bootpg)) + } :text = 0xffff +#else #if defined(CONFIG_FSL_IFC) /* Restrict bootpg at 4K boundry for IFC */ .bootpg ADDR(.text) + 0x1000 : { @@ -69,12 +76,6 @@ SECTIONS #else #error unknown NAND controller #endif -#ifdef CONFIG_SYS_MPC85XX_NO_RESETVEC - .bootpg ADDR(.text) - 0x1000 : - { - KEEP(*(.bootpg)) - } :text = 0xffff -#else .resetvec ADDR(.text) + RESET_VECTOR_OFFSET : { KEEP(*(.resetvec)) } = 0xffff diff --git a/board/freescale/c29xpcie/Makefile b/board/freescale/c29xpcie/Makefile index 626d48a..818484a 100644 --- a/board/freescale/c29xpcie/Makefile +++ b/board/freescale/c29xpcie/Makefile @@ -3,8 +3,23 @@ # # SPDX-License-Identifier: GPL-2.0+ +MINIMAL= +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL +obj-y += spl_minimal.o tlb.o law.o +else +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +endif + obj-y += c29xpcie.o obj-y += cpld.o obj-y += ddr.o obj-y += law.o obj-y += tlb.o +endif diff --git a/board/freescale/c29xpcie/cpld.c b/board/freescale/c29xpcie/cpld.c index 5cbccff..37722da 100644 --- a/board/freescale/c29xpcie/cpld.c +++ b/board/freescale/c29xpcie/cpld.c @@ -89,6 +89,7 @@ static void cpld_dump_regs(void) } #endif +#ifndef CONFIG_SPL_BUILD int cpld_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { int rc = 0; @@ -129,3 +130,4 @@ U_BOOT_CMD( "cpld_cmd dump - display the CPLD registers\n" #endif ); +#endif diff --git a/board/freescale/c29xpcie/spl.c b/board/freescale/c29xpcie/spl.c new file mode 100644 index 0000000..7bc8ce1 --- /dev/null +++ b/board/freescale/c29xpcie/spl.c @@ -0,0 +1,73 @@ +/* Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <ns16550.h> +#include <malloc.h> +#include <mmc.h> +#include <nand.h> +#include <i2c.h> + +DECLARE_GLOBAL_DATA_PTR; + +ulong get_effective_memsize(void) +{ + return CONFIG_SYS_L2_SIZE; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + console_init_f(); + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + /* Pointer is writable since we allocated a register for it */ + gd = (gd_t *)CONFIG_SPL_GD_ADDR; + bd_t *bd; + + memset(gd, 0, sizeof(gd_t)); + bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR; + bd->bi_memsize = CONFIG_SYS_L2_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + + /* relocate environment function pointers etc. */ + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; + + i2c_init_all(); + + gd->ram_size = initdram(0); + + puts("\nTertiary program loader running in sram..."); + + nand_boot(); +} diff --git a/board/freescale/c29xpcie/spl_minimal.c b/board/freescale/c29xpcie/spl_minimal.c new file mode 100644 index 0000000..7e7726d --- /dev/null +++ b/board/freescale/c29xpcie/spl_minimal.c @@ -0,0 +1,63 @@ +/* Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <mpc85xx.h> +#include <asm/io.h> +#include <ns16550.h> +#include <nand.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_law.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + +#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM) + set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM); + set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM); +#endif + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + puts("\nSecond program loader running in sram..."); + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/freescale/c29xpcie/tlb.c b/board/freescale/c29xpcie/tlb.c index 84844ee..11f8a37 100644 --- a/board/freescale/c29xpcie/tlb.c +++ b/board/freescale/c29xpcie/tlb.c @@ -26,10 +26,20 @@ struct fsl_e_tlb_entry tlb_table[] = { 0, 0, BOOKE_PAGESZ_4K, 0), /* TLB 1 */ +#ifdef CONFIG_SPL_NAND_MINIMAL + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_4K, 1), + SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_4K, 1), +#endif + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 0, BOOKE_PAGESZ_1M, 1), +#ifndef CONFIG_SPL_BUILD SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 1, BOOKE_PAGESZ_64M, 1), @@ -43,13 +53,14 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 3, BOOKE_PAGESZ_256K, 1), #endif +#endif SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 4, BOOKE_PAGESZ_64K, 1), SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, - MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 5, BOOKE_PAGESZ_64K, 1), SET_TLB_ENTRY(1, CONFIG_SYS_PLATFORM_SRAM_BASE, @@ -61,7 +72,8 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 7, BOOKE_PAGESZ_256K, 1), -#ifdef CONFIG_SYS_RAMBOOT +#if defined(CONFIG_SYS_RAMBOOT) || (defined(CONFIG_SPL) \ + && !defined(CONFIG_SPL_COMMON_INIT_DDR)) SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, @@ -71,6 +83,12 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 9, BOOKE_PAGESZ_256M, 1), #endif + +#ifdef CONFIG_SYS_INIT_L2_ADDR + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 12, BOOKE_PAGESZ_256K, 1) +#endif }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index e742746..b5f4750 100644 --- a/boards.cfg +++ b/boards.cfg @@ -784,6 +784,7 @@ Active powerpc mpc85xx - freescale bsc9132qds Active powerpc mpc85xx - freescale bsc9132qds BSC9132QDS_SPIFLASH_DDRCLK133 BSC9132QDS:BSC9132QDS,SPIFLASH,SYS_CLK_100_DDR_133 Naveen Burmi <NaveenBurmi(a)freescale.com> Active powerpc mpc85xx - freescale c29xpcie C29XPCIE C29XPCIE:C29XPCIE,36BIT Po Liu <po.liu(a)freescale.com> Active powerpc mpc85xx - freescale c29xpcie C29XPCIE_SPIFLASH C29XPCIE:C29XPCIE,36BIT,SPIFLASH Po Liu <po.liu(a)freescale.com> +Active powerpc mpc85xx - freescale c29xpcie C29XPCIE_NAND C29XPCIE:C29XPCIE,36BIT,NAND Po Liu <po.liu(a)freescale.com> Active powerpc mpc85xx - freescale corenet_ds P3041DS - - Active powerpc mpc85xx - freescale corenet_ds P3041DS_NAND P3041DS:RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000 - Active powerpc mpc85xx - freescale corenet_ds P3041DS_SDCARD P3041DS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 - diff --git a/drivers/mtd/nand/fsl_ifc_spl.c b/drivers/mtd/nand/fsl_ifc_spl.c index 9fa5ccb..5e58614 100644 --- a/drivers/mtd/nand/fsl_ifc_spl.c +++ b/drivers/mtd/nand/fsl_ifc_spl.c @@ -88,7 +88,11 @@ static inline int bad_block(uchar *marker, int port_size) return __raw_readw((u16 *)marker) != 0xffff; } +#ifdef CONFIG_TPL_BUILD +void nand_spl_load_image(uint32_t offs, int uboot_size, void *vdst) +#else static void nand_load(unsigned int offs, int uboot_size, uchar *dst) +#endif { struct fsl_ifc *ifc = IFC_BASE_ADDR; uchar *buf = (uchar *)CONFIG_SYS_NAND_BASE; @@ -105,6 +109,9 @@ static void nand_load(unsigned int offs, int uboot_size, uchar *dst) int sram_addr; int pg_no; +#ifdef CONFIG_TPL_BUILD + char *dst = vdst; +#endif /* Get NAND Flash configuration */ csor = CONFIG_SYS_NAND_CSOR; @@ -211,6 +218,15 @@ static void nand_load(unsigned int offs, int uboot_size, uchar *dst) } /* ++ * Defines a static function nand_load_image() here, because non-static makes ++ * the code too large for certain SPLs(minimal SPL, maximum size <= 4Kbytes) ++ */ +#ifndef CONFIG_TPL_BUILD +#define nand_spl_load_image(offs, uboot_size, dst) \ + nand_load(offs, uboot_size, dst) +#endif + +/* * Main entrypoint for NAND Boot. It's necessary that SDRAM is already * configured and available since this code loads the main U-boot image * from NAND into SDRAM and starts from there. @@ -221,16 +237,17 @@ void nand_boot(void) /* * Load U-Boot image from NAND into RAM */ - nand_load(CONFIG_SYS_NAND_U_BOOT_OFFS, CONFIG_SYS_NAND_U_BOOT_SIZE, - (uchar *)CONFIG_SYS_NAND_U_BOOT_DST); + nand_spl_load_image(CONFIG_SYS_NAND_U_BOOT_OFFS, + CONFIG_SYS_NAND_U_BOOT_SIZE, + (uchar *)CONFIG_SYS_NAND_U_BOOT_DST); #ifdef CONFIG_NAND_ENV_DST - nand_load(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)CONFIG_NAND_ENV_DST); + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_NAND_ENV_DST); #ifdef CONFIG_ENV_OFFSET_REDUND - nand_load(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE, - (uchar *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE); + nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE, + (uchar *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE); #endif #endif /* diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h index bb15745..d0a5010 100644 --- a/include/configs/C29XPCIE.h +++ b/include/configs/C29XPCIE.h @@ -23,6 +23,48 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_TPL +#ifdef CONFIG_TPL_BUILD +#define CONFIG_SPL_NAND_BOOT +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NAND_INIT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_COMMON_INIT_DDR +#define CONFIG_SPL_MAX_SIZE (128 << 10) +#define CONFIG_SPL_TEXT_BASE 0xf8f81000 +#define CONFIG_SYS_MPC85XX_NO_RESETVEC +#define CONFIG_SYS_NAND_U_BOOT_SIZE (576 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000) +#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000) +#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10) +#elif defined(CONFIG_SPL_BUILD) +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TEXT_BASE 0xff800000 +#define CONFIG_SPL_MAX_SIZE 8192 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000 +#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) +#endif +#define CONFIG_SPL_PAD_TO 0x20000 +#define CONFIG_TPL_PAD_TO 0x20000 +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SYS_TEXT_BASE 0x11001000 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" +#endif + #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0xeff80000 #endif @@ -31,8 +73,14 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc #endif -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif /* High Level Configuration Options */ @@ -130,6 +178,10 @@ (0xf00000000ull | CONFIG_SYS_PLATFORM_SRAM_BASE) #define CONFIG_SYS_PLATFORM_SRAM_SIZE (512 << 10) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_NO_FLASH +#endif + /* * IFC Definitions */ @@ -183,7 +235,7 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_BLOCK_SIZE (1024 * 1024) /* 8Bit NAND Flash - K9F1G08U0B */ #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ @@ -215,6 +267,23 @@ #define CONFIG_SYS_NAND_DDR_LAW 11 /* Set up IFC registers for boot location NOR/NAND */ +#ifdef CONFIG_NAND +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CSOR0_EXT CONFIG_SYS_NAND_OOBSIZE +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR @@ -230,6 +299,7 @@ #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif /* CPLD on IFC, selected by CS2 */ #define CONFIG_SYS_CPLD_BASE 0xffdf0000 @@ -269,7 +339,44 @@ #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (512 * 1024) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) +#define CONFIG_SYS_MALLOC_LEN (2 * 1024 * 1024) + +/* + * Config the L2 Cache as L2 SRAM + */ +#if defined(CONFIG_SPL_BUILD) +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024) +#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 160 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (96 << 10) +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024) +#elif defined(CONFIG_NAND) +#ifdef CONFIG_TPL_BUILD +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 +#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024) +#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10) +#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024) +#else +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_L2_SIZE (256 << 10) +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) +#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x3000) +#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) +#endif +#endif +#endif /* Serial Port */ #define CONFIG_CONS_INDEX 1 @@ -278,6 +385,10 @@ #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif + #define CONFIG_SERIAL_MULTI /* Enable both serial ports */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV @@ -364,6 +475,16 @@ #define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_SIZE 0x2000 #endif +#elif defined(CONFIG_NAND) +#define CONFIG_ENV_IS_IN_NAND +#ifdef CONFIG_TPL_BUILD +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) +#else +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_RANGE CONFIG_ENV_SIZE +#endif +#define CONFIG_ENV_OFFSET CONFIG_SYS_NAND_BLOCK_SIZE #else #define CONFIG_ENV_IS_IN_FLASH #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 -- 1.8.0

4 26

Re: [U-Boot] [PATCH 1/5] tools: mkimage: add support for gpimage format
by Wolfgang Denk 21 Jan '14

21 Jan '14

Dear Murali, In message <3E54258959B69E4282D79E01AB1F32B70466CE4A(a)DFLE11.ent.ti.com> you wrote: > > >> + if (do_swap32) { > >> + gph_size = gpimage_swap32(gph->size); > >> + gph_load_addr = gpimage_swap32(gph->load_addr); > >> + } else { > >> + gph_size = gph->size; > >> + gph_load_addr = gph->load_addr; > >> + } > > > >I think it should be possible top write this code in such a way that you can avoid both the if- > >else and passing the do_swap32 parameter. > >It is my impression that the whole endianess handling needs some refinemant. > > > >Actually I cannot see a place where do_swap32=0 is used.. > > This is done to keep the omapimage usage of this variable. Is this actually used? It appear the omapimage handling would set do_swap32=1 only when imagename == "byteswap" (see "tools/omapimage.c"). Is this a practical usecase anywhere? Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de Q: Do you know what the death rate around here is? A: One per person.

2 1

Re: [U-Boot] [PATCH 5/5] NAND: DaVinci: allow forced disable of subpage writes
by Wolfgang Denk 21 Jan '14

21 Jan '14

Dear Murali, In message <3E54258959B69E4282D79E01AB1F32B70466CE81(a)DFLE11.ent.ti.com> you wrote: > > >New CONFIG_ options MUSt be documented in the README. > > Will do. > > >Also, you are just adding dead code. There are no users for this option. > > This is a preparatory patch for keystone u-boot port and will bundle with > it if it make more sense. But this looks harmless since this option allow > users to disable subpage write. So I want to merge this right away after > adding the option name to README. Any issues? The adding of the documentation to the README and of the code should be in a single patch, not one after the other. And the patch should be art of a series that actually uses this feature. It has no logical place in the current patch series. Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de That Microsoft, the Trabant of the operating system world, may be glancing over the Berlin Wall at the Audis and BMWs and Mercedes. In their own universe Trabants and Ladas were mainstream too... -- Evan Leibovitch

1 0

Re: [U-Boot] [PATCH 4/5] arm: add support for arch timer
by Wolfgang Denk 21 Jan '14

21 Jan '14

Dear Murali, In message <3E54258959B69E4282D79E01AB1F32B70466CE69(a)DFLE11.ent.ti.com> you wrote: > > >Are we adding dead code here? Or where exactly is this code being used? > > > This is a preparatory patch for keystone port that we are currently working on. > I can repost the reworked code along with patch for the port if it can't be merged > without the user code. I cannot see any logical reason to include this patch in this series, so please resubmit when adding code that uses this feature. Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de It's not an optical illusion, it just looks like one. -- Phil White

1 0