December 2013 - U-Boot

[U-Boot] [PATCH] include/mmc.h: Remove declaration for spl_mmc_load()
by Lad, Prabhakar 08 Jan '14

08 Jan '14

From: "Lad, Prabhakar" <prabhakar.csengg(a)gmail.com> The spl_mmc_load() was removed while converting to CONFIG_SPL_FRAMEWORK usage the definition was removed but the declaration was missed. This patch removes this declaration. Signed-off-by: Lad, Prabhakar <prabhakar.csengg(a)gmail.com> --- include/mmc.h | 1 - 1 file changed, 1 deletion(-) diff --git a/include/mmc.h b/include/mmc.h index cb558da..8f51c93 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -304,7 +304,6 @@ int board_mmc_getcd(struct mmc *mmc); int mmc_switch_part(int dev_num, unsigned int part_num); int mmc_getcd(struct mmc *mmc); int mmc_getwp(struct mmc *mmc); -void spl_mmc_load(void) __noreturn; /* Function to change the size of boot partition and rpmb partitions */ int mmc_boot_partition_size_change(struct mmc *mmc, unsigned long bootsize, unsigned long rpmbsize); -- 1.7.9.5

3 2

[U-Boot] [PATCH] arm: omap: cm_t35: enable gpio bank 5 clocks explicitly
by Nikita Kiryanov 08 Jan '14

08 Jan '14

Following commit "arm: omap3: Enable clocks for peripherals only if they are used" (f33b9bd3984fb11e1d8566a866adc5957b1e1c9d) it is now necessary to enable clocks for GPIO banks explicitly. On cm_t35, GPIO bank 5 is necessary for scf0403 lcd support. Enable GPIO bank 5 clocks. Signed-off-by: Nikita Kiryanov <nikita(a)compulab.co.il> Cc: Igor Grinberg <grinberg(a)compulab.co.il> Cc: Tom Rini <trini(a)ti.com> --- include/configs/cm_t35.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index e72187e..d5c1b9c 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -319,6 +319,7 @@ /* Display Configuration */ #define CONFIG_OMAP3_GPIO_2 +#define CONFIG_OMAP3_GPIO_5 #define CONFIG_VIDEO_OMAP3 #define LCD_BPP LCD_COLOR16 -- 1.8.3.2

3 2

[U-Boot] [PATCH] ARM: twister: add missing gpio clock init
by Jeroen Hofstee 08 Jan '14

08 Jan '14

Commit f33b9bd3984fb11e1d8566a866adc5957b1e1c9d breaks boards which do not explicitly enable the gpio clocks. This causes the twister spl to hang, since it uses the no longer enabled gpio 55. Add CONFIG_OMAP3_GPIO_2 to unbrick the board. Cc: Stefano Babic <sbabic(a)denx.de> Cc: Tapani Utriainen <tapani(a)technexion.com> Signed-off-by: Jeroen Hofstee <jeroen(a)myspectrum.nl> --- include/configs/twister.h | 3 +++ 1 file changed, 3 insertions(+) diff --git a/include/configs/twister.h b/include/configs/twister.h index b6ca59c..f24dc13 100644 --- a/include/configs/twister.h +++ b/include/configs/twister.h @@ -50,4 +50,7 @@ #define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100) #define CONFIG_SPL_BOARD_INIT +/* gpio 55 is used as SPL_OS_BOOT_KEY */ +#define CONFIG_OMAP3_GPIO_2 + #endif /* __CONFIG_H */ -- 1.8.3.2

3 2

[U-Boot] [PATCH] ARM: tam3517-common: fix nand spl boot
by Jeroen Hofstee 08 Jan '14

08 Jan '14

commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30, "mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme" removed CONFIG_SPL_NAND_SOFTECC from the tam3517 common config, causing the spl nand boot to fail. Add it back, so derived boards boot again. Cc: Pekon Gupta <pekon(a)ti.com> Cc: Scott Wood <scottwood(a)freescale.com> Cc: Raphael Assenat <raph(a)8d.com> Cc: Stefano Babic <sbabic(a)denx.de> Cc: Tapani Utriainen <tapani(a)technexion.com> Signed-off-by: Jeroen Hofstee <jeroen(a)myspectrum.nl> --- include/configs/tam3517-common.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index 439fc47..d44b5c0 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -224,6 +224,7 @@ #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_CONSOLE #define CONFIG_SPL_NAND_SIMPLE +#define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */ #define CONFIG_SPL_LIBCOMMON_SUPPORT -- 1.8.3.2

3 2

[U-Boot] [PATCH] TI:omap3: Drop omap3_zoom2
by Tom Rini 08 Jan '14

08 Jan '14

The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ and Tom Rix's email has long been bouncing. Signed-off-by: Tom Rini <trini(a)ti.com> --- board/logicpd/zoom2/Makefile | 11 -- board/logicpd/zoom2/config.mk | 17 --- board/logicpd/zoom2/debug_board.c | 44 ------- board/logicpd/zoom2/led.c | 116 ------------------ board/logicpd/zoom2/zoom2.c | 183 ---------------------------- board/logicpd/zoom2/zoom2.h | 142 --------------------- board/logicpd/zoom2/zoom2_serial.c | 130 -------------------- board/logicpd/zoom2/zoom2_serial.h | 59 --------- boards.cfg | 1 - drivers/serial/ns16550.c | 5 +- include/configs/omap3_zoom2.h | 237 ------------------------------------ 11 files changed, 2 insertions(+), 943 deletions(-) delete mode 100644 board/logicpd/zoom2/Makefile delete mode 100644 board/logicpd/zoom2/config.mk delete mode 100644 board/logicpd/zoom2/debug_board.c delete mode 100644 board/logicpd/zoom2/led.c delete mode 100644 board/logicpd/zoom2/zoom2.c delete mode 100644 board/logicpd/zoom2/zoom2.h delete mode 100644 board/logicpd/zoom2/zoom2_serial.c delete mode 100644 board/logicpd/zoom2/zoom2_serial.h delete mode 100644 include/configs/omap3_zoom2.h diff --git a/board/logicpd/zoom2/Makefile b/board/logicpd/zoom2/Makefile deleted file mode 100644 index 8ec5f25..0000000 --- a/board/logicpd/zoom2/Makefile +++ /dev/null @@ -1,11 +0,0 @@ -# -# (C) Copyright 2000, 2001, 2002 -# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := zoom2.o -obj-y += debug_board.o -obj-y += zoom2_serial.o -obj-$(CONFIG_STATUS_LED) += led.o diff --git a/board/logicpd/zoom2/config.mk b/board/logicpd/zoom2/config.mk deleted file mode 100644 index 1c382f7..0000000 --- a/board/logicpd/zoom2/config.mk +++ /dev/null @@ -1,17 +0,0 @@ -# -# (C) Copyright 2009 -# Texas Instruments, <www.ti.com> -# -# Zoom II uses OMAP3 (ARM-CortexA8) CPU -# see http://www.ti.com/ for more information on Texas Instruments -# -# SPDX-License-Identifier: GPL-2.0+ -# -# Physical Address: -# 0x80000000 (bank0) -# 0xA0000000 (bank1) -# Linux-Kernel is expected to be at 0x80008000, entry 0x80008000 -# (mem base + reserved) - -# For use with external or internal boots. -CONFIG_SYS_TEXT_BASE = 0x80008000 diff --git a/board/logicpd/zoom2/debug_board.c b/board/logicpd/zoom2/debug_board.c deleted file mode 100644 index 071f410..0000000 --- a/board/logicpd/zoom2/debug_board.c +++ /dev/null @@ -1,44 +0,0 @@ -/* - * Copyright (c) 2009 Wind River Systems, Inc. - * Tom Rix <Tom.Rix(a)windriver.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <asm/arch/cpu.h> -#include <asm/io.h> -#include <asm/arch/mux.h> -#include <asm/gpio.h> - -#define DEBUG_BOARD_CONNECTED 1 -#define DEBUG_BOARD_NOT_CONNECTED 0 - -static int debug_board_connected = DEBUG_BOARD_CONNECTED; - -static void zoom2_debug_board_detect (void) -{ - int val = 0; - - if (!gpio_request(158, "")) { - /* - * GPIO to query for debug board - * 158 db board query - */ - gpio_direction_input(158); - val = gpio_get_value(158); - } - - if (!val) - debug_board_connected = DEBUG_BOARD_NOT_CONNECTED; -} - -int zoom2_debug_board_connected (void) -{ - static int first_time = 1; - - if (first_time) { - zoom2_debug_board_detect (); - first_time = 0; - } - return debug_board_connected; -} diff --git a/board/logicpd/zoom2/led.c b/board/logicpd/zoom2/led.c deleted file mode 100644 index 5d37ac1..0000000 --- a/board/logicpd/zoom2/led.c +++ /dev/null @@ -1,116 +0,0 @@ -/* - * Copyright (c) 2009 Wind River Systems, Inc. - * Tom Rix <Tom.Rix(a)windriver.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <status_led.h> -#include <asm/arch/cpu.h> -#include <asm/io.h> -#include <asm/arch/sys_proto.h> -#include <asm/gpio.h> - -static unsigned int saved_state[2] = {STATUS_LED_OFF, STATUS_LED_OFF}; - -/* - * GPIO LEDs - * 173 red - * 154 blue - * 61 blue2 - */ -#define ZOOM2_LED_RED 173 -#define ZOOM2_LED_BLUE 154 -#define ZOOM2_LED_BLUE2 61 - -void red_led_off(void) -{ - /* red */ - if (!gpio_request(ZOOM2_LED_RED, "")) { - gpio_direction_output(ZOOM2_LED_RED, 0); - gpio_set_value(ZOOM2_LED_RED, 0); - } - saved_state[STATUS_LED_RED] = STATUS_LED_OFF; -} - -void blue_led_off(void) -{ - /* blue */ - if (!gpio_request(ZOOM2_LED_BLUE, "")) { - gpio_direction_output(ZOOM2_LED_BLUE, 0); - gpio_set_value(ZOOM2_LED_BLUE, 0); - } - - /* blue 2 */ - if (!gpio_request(ZOOM2_LED_BLUE2, "")) { - gpio_direction_output(ZOOM2_LED_BLUE2, 0); - gpio_set_value(ZOOM2_LED_BLUE2, 0); - } - saved_state[STATUS_LED_BLUE] = STATUS_LED_OFF; -} - -void red_led_on(void) -{ - blue_led_off(); - - /* red */ - if (!gpio_request(ZOOM2_LED_RED, "")) { - gpio_direction_output(ZOOM2_LED_RED, 0); - gpio_set_value(ZOOM2_LED_RED, 1); - } - saved_state[STATUS_LED_RED] = STATUS_LED_ON; -} - -void blue_led_on(void) -{ - red_led_off(); - - /* blue */ - if (!gpio_request(ZOOM2_LED_BLUE, "")) { - gpio_direction_output(ZOOM2_LED_BLUE, 0); - gpio_set_value(ZOOM2_LED_BLUE, 1); - } - - /* blue 2 */ - if (!gpio_request(ZOOM2_LED_BLUE2, "")) { - gpio_direction_output(ZOOM2_LED_BLUE2, 0); - gpio_set_value(ZOOM2_LED_BLUE2, 1); - } - - saved_state[STATUS_LED_BLUE] = STATUS_LED_ON; -} - -void __led_init (led_id_t mask, int state) -{ - __led_set (mask, state); -} - -void __led_toggle (led_id_t mask) -{ - if (STATUS_LED_BLUE == mask) { - if (STATUS_LED_ON == saved_state[STATUS_LED_BLUE]) - blue_led_off(); - else - blue_led_on(); - } else if (STATUS_LED_RED == mask) { - if (STATUS_LED_ON == saved_state[STATUS_LED_RED]) - red_led_off(); - else - red_led_on(); - } -} - -void __led_set (led_id_t mask, int state) -{ - if (STATUS_LED_BLUE == mask) { - if (STATUS_LED_ON == state) - blue_led_on(); - else - blue_led_off(); - } else if (STATUS_LED_RED == mask) { - if (STATUS_LED_ON == state) - red_led_on(); - else - red_led_off(); - } -} diff --git a/board/logicpd/zoom2/zoom2.c b/board/logicpd/zoom2/zoom2.c deleted file mode 100644 index e14de04..0000000 --- a/board/logicpd/zoom2/zoom2.c +++ /dev/null @@ -1,183 +0,0 @@ -/* - * Copyright (c) 2009 Wind River Systems, Inc. - * Tom Rix <Tom.Rix(a)windriver.com> - * - * Derived from Zoom1 code by - * Nishanth Menon <nm(a)ti.com> - * Sunil Kumar <sunilsaini05(a)gmail.com> - * Shashi Ranjan <shashiranjanmca05(a)gmail.com> - * Richard Woodruff <r-woodruff2(a)ti.com> - * Syed Mohammed Khasim <khasim(a)ti.com> - * - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <netdev.h> -#ifdef CONFIG_STATUS_LED -#include <status_led.h> -#endif -#include <twl4030.h> -#include <asm/io.h> -#include <asm/arch/mmc_host_def.h> -#include <asm/gpio.h> -#include <asm/arch/mem.h> -#include <asm/arch/mux.h> -#include <asm/arch/sys_proto.h> -#include <asm/mach-types.h> -#include "zoom2.h" -#include "zoom2_serial.h" - -DECLARE_GLOBAL_DATA_PTR; - -/* - * This the the zoom2, board specific, gpmc configuration for the - * quad uart on the debug board. The more general gpmc configurations - * are setup at the cpu level in arch/arm/cpu/armv7/omap3/mem.c - * - * The details of the setting of the serial gpmc setup are not available. - * The values were provided by another party. - */ -static u32 gpmc_serial_TL16CP754C[GPMC_MAX_REG] = { - 0x00011000, - 0x001F1F01, - 0x00080803, - 0x1D091D09, - 0x041D1F1F, - 0x1D0904C4, 0 -}; - -/* Used to track the revision of the board */ -static zoom2_revision revision = ZOOM2_REVISION_UNKNOWN; - -/* - * Routine: zoom2_get_revision - * Description: Return the revision of the Zoom2 this code is running on. - */ -zoom2_revision zoom2_get_revision(void) -{ - return revision; -} - -/* - * Routine: zoom2_identify - * Description: Detect which version of Zoom2 we are running on. - */ -void zoom2_identify(void) -{ - /* - * To check for production board vs beta board, - * check if gpio 94 is clear. - * - * No way yet to check for alpha board identity. - * Alpha boards were produced in very limited quantities - * and they are not commonly used. They are mentioned here - * only for completeness. - */ - if (!gpio_request(94, "")) { - unsigned int val; - - gpio_direction_input(94); - val = gpio_get_value(94); - - if (val) - revision = ZOOM2_REVISION_BETA; - else - revision = ZOOM2_REVISION_PRODUCTION; - } - - printf("Board revision "); - switch (revision) { - case ZOOM2_REVISION_PRODUCTION: - printf("Production\n"); - break; - case ZOOM2_REVISION_BETA: - printf("Beta\n"); - break; - default: - printf("Unknown\n"); - break; - } -} - -/* - * Routine: board_init - * Description: Early hardware init. - */ -int board_init (void) -{ - u32 *gpmc_config; - - gpmc_init (); /* in SRAM or SDRAM, finish GPMC */ - - /* Configure console support on zoom2 */ - gpmc_config = gpmc_serial_TL16CP754C; - enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[3], - SERIAL_TL16CP754C_BASE, GPMC_SIZE_16M); - - /* board id for Linux */ - gd->bd->bi_arch_number = MACH_TYPE_OMAP_ZOOM2; - /* boot param addr */ - gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); - -#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT) - status_led_set (STATUS_LED_BOOT, STATUS_LED_ON); -#endif - return 0; -} - -/* - * Routine: misc_init_r - * Description: Configure zoom board specific configurations - */ -int misc_init_r(void) -{ - zoom2_identify(); - twl4030_power_init(); - twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON); - dieid_num_r(); - - /* - * Board Reset - * The board is reset by holding the the large button - * on the top right side of the main board for - * eight seconds. - * - * There are reported problems of some beta boards - * continously resetting. For those boards, disable resetting. - */ - if (ZOOM2_REVISION_PRODUCTION <= zoom2_get_revision()) - twl4030_power_reset_init(); - - return 0; -} - -/* - * Routine: set_muxconf_regs - * Description: Setting up the configuration Mux registers specific to the - * hardware. Many pins need to be moved from protect to primary - * mode. - */ -void set_muxconf_regs (void) -{ - /* platform specific muxes */ - MUX_ZOOM2 (); -} - -#ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) -{ - return omap_mmc_init(0, 0, 0, -1, -1); -} -#endif - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_LAN91C96 - rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE); -#endif - return rc; -} -#endif diff --git a/board/logicpd/zoom2/zoom2.h b/board/logicpd/zoom2/zoom2.h deleted file mode 100644 index 850c790..0000000 --- a/board/logicpd/zoom2/zoom2.h +++ /dev/null @@ -1,142 +0,0 @@ -/* - * Copyright (c) 2009 Wind River Systems, Inc. - * Tom Rix <Tom.Rix(a)windriver.com> - * - * Derived from: board/omap3/zoom1/zoom1.h - * Nishanth Menon <nm(a)ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef _BOARD_ZOOM2_H_ -#define _BOARD_ZOOM2_H_ - -const omap3_sysinfo sysinfo = { - DDR_STACKED, - "OMAP3 Zoom2 ", - "NAND", -}; - -typedef enum { - ZOOM2_REVISION_UNKNOWN = 0, - ZOOM2_REVISION_ALPHA, - ZOOM2_REVISION_BETA, - ZOOM2_REVISION_PRODUCTION -} zoom2_revision; - -zoom2_revision zoom2_get_revision(void); - -/* - * IEN - Input Enable - * IDIS - Input Disable - * PTD - Pull type Down - * PTU - Pull type Up - * DIS - Pull type selection is inactive - * EN - Pull type selection is active - * M0 - Mode 0 - * The commented string gives the final mux configuration for that pin - */ -#define MUX_ZOOM2() \ - /* SDRC*/\ - MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /* SDRC_D0 */\ - MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /* SDRC_D1 */\ - MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /* SDRC_D2 */\ - MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /* SDRC_D3 */\ - MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /* SDRC_D4 */\ - MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /* SDRC_D5 */\ - MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /* SDRC_D6 */\ - MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /* SDRC_D7 */\ - MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /* SDRC_D8 */\ - MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /* SDRC_D9 */\ - MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /* SDRC_D10 */\ - MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /* SDRC_D11 */\ - MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /* SDRC_D12 */\ - MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /* SDRC_D13 */\ - MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /* SDRC_D14 */\ - MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /* SDRC_D15 */\ - MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /* SDRC_D16 */\ - MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /* SDRC_D17 */\ - MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /* SDRC_D18 */\ - MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /* SDRC_D19 */\ - MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /* SDRC_D20 */\ - MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /* SDRC_D21 */\ - MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /* SDRC_D22 */\ - MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /* SDRC_D23 */\ - MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /* SDRC_D24 */\ - MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /* SDRC_D25 */\ - MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /* SDRC_D26 */\ - MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /* SDRC_D27 */\ - MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /* SDRC_D28 */\ - MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /* SDRC_D29 */\ - MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /* SDRC_D30 */\ - MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /* SDRC_D31 */\ - MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /* SDRC_CLK */\ - MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /* SDRC_DQS0 */\ - MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /* SDRC_DQS1 */\ - MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /* SDRC_DQS2 */\ - MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /* SDRC_DQS3 */\ -/* GPMC */\ - MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /* GPMC_A1 */\ - MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /* GPMC_A2 */\ - MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /* GPMC_A3 */\ - MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /* GPMC_A4 */\ - MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /* GPMC_A5 */\ - MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /* GPMC_A6 */\ - MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /* GPMC_A7 */\ - MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /* GPMC_A8 */\ - MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /* GPMC_A9 */\ - MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /* GPMC_A10 */\ - MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /* GPMC_D0 */\ - MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /* GPMC_D1 */\ - MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /* GPMC_D2 */\ - MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /* GPMC_D3 */\ - MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /* GPMC_D4 */\ - MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /* GPMC_D5 */\ - MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /* GPMC_D6 */\ - MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /* GPMC_D7 */\ - MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /* GPMC_D8 */\ - MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /* GPMC_D9 */\ - MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /* GPMC_D10 */\ - MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /* GPMC_D11 */\ - MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /* GPMC_D12 */\ - MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /* GPMC_D13 */\ - MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /* GPMC_D14 */\ - MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /* GPMC_D15 */\ - MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /* GPMC_nCS0 */\ - MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M7)) /* GPMC_nCS1 */\ - MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M7)) /* GPMC_nCS2 */\ - MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M7)) /* GPMC_nCS3 */\ - MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M7)) /* GPMC_nCS4 */\ - MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M7)) /* GPMC_nCS5 */\ - MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M7)) /* GPMC_nCS6 */\ - MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M7)) /* GPMC_nCS7 */\ - MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /* GPMC_CLK */\ - MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /* GPMC_nADV_ALE */\ - MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /* GPMC_nOE */\ - MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /* GPMC_nWE */\ - MUX_VAL(CP(GPMC_NWP), (IDIS | PTU | DIS | M0)) /* GPMC_nWP */\ - MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0)) /* GPMC_nBE0_CLE */\ - MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /* GPMC_nBE1 */\ - MUX_VAL(CP(GPMC_WAIT0), (IEN | PTD | EN | M0)) /* GPMC_WAIT0 */\ - MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /* GPMC_WAIT1 */\ - MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /* GPMC_WAIT2 */\ - MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /* GPMC_WAIT3 */\ -/* IDCC modem Power On */\ - MUX_VAL(CP(CAM_D11), (IEN | PTU | EN | M4)) /* GPIO_110 */\ - MUX_VAL(CP(CAM_D4), (IEN | PTU | EN | M4)) /* GPIO_103 */\ -/* GPMC CS7 has LAN9211 device */\ - MUX_VAL(CP(GPMC_NCS7), (IDIS | PTU | EN | M0)) /* GPMC_nCS7 */\ - MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | DIS | M4)) /* LAN9221 */\ - MUX_VAL(CP(MCSPI1_CS2), (IEN | PTD | EN | M0)) /* MCSPI1_CS2 */\ -/* GPMC CS3 has Serial TL16CP754C device */\ - MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /* GPMC_nCS3 */\ -/* Toggle Reset pin of TL16CP754C device */\ - MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTU | EN | M4)) /* GPIO_152 */\ - udelay(10);\ - MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | EN | M4)) /* GPIO_152 */\ - MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /* SDRC_CKE1 */\ -/* LEDS */\ - MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | EN | M4)) /* GPIO_173 red */\ - MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | EN | M4)) /* GPIO_154 blue */\ - MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | EN | M4)) /* GPIO_61 blue2 */ - -#endif /* _BOARD_ZOOM2_H_ */ diff --git a/board/logicpd/zoom2/zoom2_serial.c b/board/logicpd/zoom2/zoom2_serial.c deleted file mode 100644 index 2959276..0000000 --- a/board/logicpd/zoom2/zoom2_serial.c +++ /dev/null @@ -1,130 +0,0 @@ -/* - * Copyright (c) 2009 Wind River Systems, Inc. - * Tom Rix <Tom.Rix(a)windriver.com> - * - * SPDX-License-Identifier: GPL-2.0+ - * - * This file was adapted from arch/powerpc/cpu/mpc5xxx/serial.c - */ - -#include <common.h> -#include <serial.h> -#include <ns16550.h> -#include <asm/arch/cpu.h> -#include "zoom2_serial.h" - -int quad_init_dev (unsigned long base) -{ - /* - * The Quad UART is on the debug board. - * Check if the debug board is attached before using the UART - */ - if (zoom2_debug_board_connected ()) { - NS16550_t com_port = (NS16550_t) base; - int baud_divisor = CONFIG_SYS_NS16550_CLK / 16 / - CONFIG_BAUDRATE; - - /* - * Zoom2 has a board specific initialization of its UART. - * This generic initialization has been copied from - * drivers/serial/ns16550.c. The macros have been expanded. - * - * Do the following instead of - * - * NS16550_init (com_port, clock_divisor); - */ - com_port->ier = 0x00; - - /* - * On Zoom2 board Set pre-scalar to 1 - * CLKSEL is GND => MCR[7] is 1 => preslr is 4 - * So change the prescl to 1 - */ - com_port->lcr = 0xBF; - com_port->fcr |= 0x10; - com_port->mcr &= 0x7F; - - /* This is generic ns16550.c setup */ - com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1; - com_port->dll = 0; - com_port->dlm = 0; - com_port->lcr = UART_LCR_8N1; - com_port->mcr = UART_MCR_DTR | UART_MCR_RTS; - com_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR | - UART_FCR_TXSR; - com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1; - com_port->dll = baud_divisor & 0xff; - com_port->dlm = (baud_divisor >> 8) & 0xff; - com_port->lcr = UART_LCR_8N1; - } - /* - * We have to lie here, otherwise the board init code will hang - * on the check - */ - return 0; -} - -void quad_putc_dev (unsigned long base, const char c) -{ - if (zoom2_debug_board_connected ()) { - - if (c == '\n') - quad_putc_dev (base, '\r'); - - NS16550_putc ((NS16550_t) base, c); - } else { - usbtty_putc(c); - } -} - -void quad_puts_dev (unsigned long base, const char *s) -{ - if (zoom2_debug_board_connected ()) { - while ((s != NULL) && (*s != '\0')) - quad_putc_dev (base, *s++); - } else { - usbtty_puts(s); - } -} - -int quad_getc_dev (unsigned long base) -{ - if (zoom2_debug_board_connected ()) - return NS16550_getc ((NS16550_t) base); - - return usbtty_getc(); -} - -int quad_tstc_dev (unsigned long base) -{ - if (zoom2_debug_board_connected ()) - return NS16550_tstc ((NS16550_t) base); - - return usbtty_tstc(); -} - -void quad_setbrg_dev (unsigned long base) -{ - if (zoom2_debug_board_connected ()) { - - int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 / - CONFIG_BAUDRATE; - - NS16550_reinit ((NS16550_t) base, clock_divisor); - } -} - -QUAD_INIT (0) -QUAD_INIT (1) -QUAD_INIT (2) -QUAD_INIT (3) - -struct serial_device *default_serial_console(void) -{ - switch (ZOOM2_DEFAULT_SERIAL_DEVICE) { - case 0: return &zoom2_serial_device0; - case 1: return &zoom2_serial_device1; - case 2: return &zoom2_serial_device2; - case 3: return &zoom2_serial_device3; - } -} diff --git a/board/logicpd/zoom2/zoom2_serial.h b/board/logicpd/zoom2/zoom2_serial.h deleted file mode 100644 index 8224452..0000000 --- a/board/logicpd/zoom2/zoom2_serial.h +++ /dev/null @@ -1,59 +0,0 @@ -/* - * Copyright (c) 2009 Wind River Systems, Inc. - * Tom Rix <Tom.Rix(a)windriver.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef ZOOM2_SERIAL_H -#define ZOOM2_SERIAL_H - -#include <linux/stringify.h> - -extern int zoom2_debug_board_connected (void); - -#define SERIAL_TL16CP754C_BASE 0x10000000 /* Zoom2 Serial chip address */ - -#define QUAD_BASE_0 SERIAL_TL16CP754C_BASE -#define QUAD_BASE_1 (SERIAL_TL16CP754C_BASE + 0x100) -#define QUAD_BASE_2 (SERIAL_TL16CP754C_BASE + 0x200) -#define QUAD_BASE_3 (SERIAL_TL16CP754C_BASE + 0x300) - -#define QUAD_INIT(n) \ -int quad_init_##n(void) \ -{ \ - return quad_init_dev(QUAD_BASE_##n); \ -} \ -void quad_setbrg_##n(void) \ -{ \ - quad_setbrg_dev(QUAD_BASE_##n); \ -} \ -void quad_putc_##n(const char c) \ -{ \ - quad_putc_dev(QUAD_BASE_##n, c); \ -} \ -void quad_puts_##n(const char *s) \ -{ \ - quad_puts_dev(QUAD_BASE_##n, s); \ -} \ -int quad_getc_##n(void) \ -{ \ - return quad_getc_dev(QUAD_BASE_##n); \ -} \ -int quad_tstc_##n(void) \ -{ \ - return quad_tstc_dev(QUAD_BASE_##n); \ -} \ -struct serial_device zoom2_serial_device##n = \ -{ \ - .name = __stringify(n), \ - .start = quad_init_##n, \ - .stop = NULL, \ - .setbrg = quad_setbrg_##n, \ - .getc = quad_getc_##n, \ - .tstc = quad_tstc_##n, \ - .putc = quad_putc_##n, \ - .puts = quad_puts_##n, \ -}; - -#endif /* ZOOM2_SERIAL_H */ diff --git a/boards.cfg b/boards.cfg index c602a16..9105635 100644 --- a/boards.cfg +++ b/boards.cfg @@ -325,7 +325,6 @@ Active arm armv7 omap3 isee igep00x0 Active arm armv7 omap3 logicpd am3517evm am3517_evm - Vaibhav Hiremath <hvaibhav(a)ti.com> Active arm armv7 omap3 logicpd omap3som omap3_logic - Peter Barada <peter.barada(a)logicpd.com> Active arm armv7 omap3 logicpd zoom1 omap3_zoom1 - Nishanth Menon <nm(a)ti.com> -Active arm armv7 omap3 logicpd zoom2 omap3_zoom2 - Tom Rix <Tom.Rix(a)windriver.com> Active arm armv7 omap3 matrix_vision mvblx omap3_mvblx - Michael Jones <michael.jones(a)matrix-vision.de> Active arm armv7 omap3 nokia rx51 nokia_rx51 - Pali Rohár <pali.rohar(a)gmail.com> Active arm armv7 omap3 technexion twister twister - Stefano Babic <sbabic(a)denx.de> diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c index 181c818..fbc37b2 100644 --- a/drivers/serial/ns16550.c +++ b/drivers/serial/ns16550.c @@ -56,9 +56,8 @@ void NS16550_init(NS16550_t com_port, int baud_divisor) ; serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier); -#if (defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)) || \ - defined(CONFIG_AM33XX) || defined(CONFIG_TI81XX) || \ - defined(CONFIG_AM43XX) +#if defined(CONFIG_OMAP) || defined(CONFIG_AM33XX) || \ + defined(CONFIG_TI81XX) || defined(CONFIG_AM43XX) serial_out(0x7, &com_port->mdr1); /* mode select reset TL16C750*/ #endif serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr); diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h deleted file mode 100644 index f749740..0000000 --- a/include/configs/omap3_zoom2.h +++ /dev/null @@ -1,237 +0,0 @@ -/* - * (C) Copyright 2006-2009 - * Texas Instruments. - * Richard Woodruff <r-woodruff2(a)ti.com> - * Syed Mohammed Khasim <x0khasim(a)ti.com> - * Nishanth Menon <nm(a)ti.com> - * Tom Rix <Tom.Rix(a)windriver.com> - * - * Configuration settings for the TI OMAP3430 Zoom II board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP34XX 1 /* which is a 34XX */ -#define CONFIG_OMAP3_ZOOM2 1 /* working with Zoom II */ -#define CONFIG_OMAP_GPIO -#define CONFIG_OMAP_COMMON - -#define CONFIG_SDRC /* The chip has SDRC controller */ - -#include <asm/arch/cpu.h> /* get chip and board defs */ -#include <asm/arch/omap3.h> - -/* - * Display CPU and Board information - */ -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - -#define CONFIG_MISC_INIT_R - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#define CONFIG_OF_LIBFDT 1 - -/* - * Size of malloc() pool - */ -#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ - /* Sector */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) -/* - * Hardware drivers - */ - -/* - * NS16550 Configuration - * Zoom2 uses the TL16CP754C on the debug board - */ -/* - * 0 - 1 : first USB with respect to the left edge of the debug board - * 2 - 3 : second USB with respect to the left edge of the debug board - */ -#define ZOOM2_DEFAULT_SERIAL_DEVICE 0 - -#define V_NS16550_CLK (1843200) /* 1.8432 Mhz */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_REG_SIZE (-2) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {115200} - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_GENERIC_MMC 1 -#define CONFIG_MMC 1 -#define CONFIG_OMAP_HSMMC 1 -#define CONFIG_DOS_PARTITION 1 - -/* Status LED */ -#define CONFIG_STATUS_LED 1 /* Status LED enabled */ -#define CONFIG_BOARD_SPECIFIC_LED 1 -#define STATUS_LED_BLUE 0 -#define STATUS_LED_RED 1 -/* Blue */ -#define STATUS_LED_BIT STATUS_LED_BLUE -#define STATUS_LED_STATE STATUS_LED_ON -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -/* Red */ -#define STATUS_LED_BIT1 STATUS_LED_RED -#define STATUS_LED_STATE1 STATUS_LED_OFF -#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) -/* Optional value */ -#define STATUS_LED_BOOT STATUS_LED_BIT - -/* GPIO banks */ -#ifdef CONFIG_STATUS_LED -#define CONFIG_OMAP3_GPIO_2 /* ZOOM2_LED_BLUE2 */ -#define CONFIG_OMAP3_GPIO_6 /* ZOOM2_LED_RED */ -#endif -#define CONFIG_OMAP3_GPIO_3 /* board revision */ -#define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */ - -/* USB */ -#define CONFIG_MUSB_UDC 1 -#define CONFIG_USB_OMAP3 1 -#define CONFIG_TWL4030_USB 1 - -/* USB device configuration */ -#define CONFIG_USB_DEVICE 1 -#define CONFIG_USB_TTY 1 -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "Zoom2" - -/* commands to include */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_FAT /* FAT support */ -#define CONFIG_CMD_I2C /* I2C serial bus support */ -#define CONFIG_CMD_MMC /* MMC support */ -#define CONFIG_CMD_NAND /* NAND support */ -#define CONFIG_CMD_NAND_LOCK_UNLOCK /* Enable lock/unlock support */ - -#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ -#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ -#undef CONFIG_CMD_IMI /* iminfo */ -#undef CONFIG_CMD_IMLS /* List all found images */ -#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ -#undef CONFIG_CMD_NFS /* NFS support */ - -#define CONFIG_SYS_NO_FLASH -#define CONFIG_SYS_I2C -#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 -#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 -#define CONFIG_SYS_I2C_OMAP34XX - -/* - * TWL4030 - */ -#define CONFIG_TWL4030_POWER 1 -#define CONFIG_TWL4030_LED 1 - -/* - * Board NAND Info. - */ -#define CONFIG_NAND_OMAP_GPMC -#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ - /* to access nand */ -#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ - /* to access nand at */ - /* CS0 */ -#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 - -/* Environment information */ -#define CONFIG_BOOTDELAY 10 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "usbtty=cdc_acm\0" \ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_PROMPT "OMAP3 Zoom2 # " -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_CBSIZE 512 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) -/* Memtest from start of memory to 31MB */ -#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) -#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + 0x01F00000) -/* The default load address is the start of memory */ -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) -/* everything, incl board info, in Hz */ -#undef CONFIG_SYS_CLKS_IN_HZ -/* - * 2430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by - * 32KHz clk, or from external sig. This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) -#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */ -#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV)) - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -/* **** PISMO SUPPORT *** */ - -/* Configure the PISMO */ -#define PISMO1_NAND_SIZE GPMC_SIZE_128M -#define PISMO1_ONEN_SIZE GPMC_SIZE_128M - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE -#endif - -/* Monitor at start of flash */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE - -#define CONFIG_ENV_IS_IN_NAND 1 -#define SMNAND_ENV_OFFSET 0x0c0000 /* environment starts here */ - -#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ -#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET -#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET - -#define CONFIG_SYS_CACHELINE_SIZE 64 - -#endif /* __CONFIG_H */ -- 1.7.9.5

1 1

[U-Boot] [PATCH] cam_enc_4xx: Set CONFIG_SYS_NAND_MAX_OOBFREE / CONFIG_SYS_NAND_MAX_ECCPOS
by Tom Rini 08 Jan '14

08 Jan '14

With the changes to make OOBFREE/ECCPOS configurable but default to larger, we need to set these config options for the space savings they provide. Cc: Scott Wood <scottwood(a)freescale.com> Cc: Heiko Schocher <hs(a)denx.de> Signed-off-by: Tom Rini <trini(a)ti.com> --- include/configs/cam_enc_4xx.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/include/configs/cam_enc_4xx.h b/include/configs/cam_enc_4xx.h index c1042ae..8182a75 100644 --- a/include/configs/cam_enc_4xx.h +++ b/include/configs/cam_enc_4xx.h @@ -236,6 +236,8 @@ #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 #define CONFIG_SYS_NAND_ECCSIZE 0x200 #define CONFIG_SYS_NAND_ECCBYTES 10 +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_MAX_ECCPOS 56 #define CONFIG_SYS_NAND_OOBSIZE 64 #define CONFIG_SYS_NAND_5_ADDR_CYCLE -- 1.7.9.5

1 1

[U-Boot] [PATCH] cmd_sf: Mention in the help text that mode, addr, offset and len must be given in hex.
by Jakob Unterwurzacher 08 Jan '14

08 Jan '14

These parameters are always interpreted as hex, even without 0x prefix. Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher(a)theobroma-systems.com> --- common/cmd_sf.c | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/common/cmd_sf.c b/common/cmd_sf.c index 0a17782..0f7c0a3 100644 --- a/common/cmd_sf.c +++ b/common/cmd_sf.c @@ -531,6 +531,7 @@ U_BOOT_CMD( "sf erase offset [+]len - erase `len' bytes from `offset'\n" " `+len' round up `len' to block size\n" "sf update addr offset len - erase and write `len' bytes from memory\n" - " at `addr' to flash at `offset'" + " at `addr' to flash at `offset'\n" + "Parameters mode, addr, offset and len must be in hex." SF_TEST_HELP ); -- 1.7.2.5

2 1

[U-Boot] [PATCH] spi: soft_spi: Support NULL din/dout buffers
by Andrew Ruder 08 Jan '14

08 Jan '14

This mirrors the conventions used in other SPI drivers (kirkwood, davinci, atmel, et al) where the din/dout buffer can be NULL when the received/transmitted data isn't important. This reduces the need for allocating additional buffers when write-only/read-only functionality is needed. In the din == NULL case, the received data is simply not stored. In the dout == NULL case, zeroes are transmitted. Signed-off-by: Andrew Ruder <andrew.ruder(a)elecsyscorp.com> --- drivers/spi/soft_spi.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) diff --git a/drivers/spi/soft_spi.c b/drivers/spi/soft_spi.c index 5d22351..5fdd091 100644 --- a/drivers/spi/soft_spi.c +++ b/drivers/spi/soft_spi.c @@ -137,9 +137,15 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, * Check if it is time to work on a new byte. */ if((j % 8) == 0) { - tmpdout = *txd++; + if (txd) { + tmpdout = *txd++; + } else { + tmpdout = 0; + } if(j != 0) { - *rxd++ = tmpdin; + if (rxd) { + *rxd++ = tmpdin; + } } tmpdin = 0; } @@ -164,9 +170,11 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, * bits over to left-justify them. Then store the last byte * read in. */ - if((bitlen % 8) != 0) - tmpdin <<= 8 - (bitlen % 8); - *rxd++ = tmpdin; + if (rxd) { + if((bitlen % 8) != 0) + tmpdin <<= 8 - (bitlen % 8); + *rxd++ = tmpdin; + } if (flags & SPI_XFER_END) spi_cs_deactivate(slave); -- 1.8.4.rc3

2 1

[U-Boot] [UBOOT][PATCHv2 0/5] qspi: Add AM437x support
by Sourav Poddar 08 Jan '14

08 Jan '14

The patch series add support for enabling qspi on AM43xx at uboot. Testing done: ------------- Wrote a uImage to the flash, read it back and boot the kernel. v1->v2: Remove patch 3 of previous version, as support was already added for macronix flash. Created a doc explaining the test details. This patches are developed and tested on top of the following tree: git://git.denx.de/u-boot-ti.git branch: master Sourav Poddar (5): am43xx: add qspi support am437x_epos_evm: add SPL API, QSPI, and serial flash support qspi/spi: Add AM43xx specifics changes am43xx: add delay before xfer doc: qspi: Add qspi test details on AM43xx arch/arm/cpu/armv7/am33xx/clock_am43xx.c | 1 + arch/arm/include/asm/arch-am33xx/cpu.h | 4 +- arch/arm/include/asm/arch-am33xx/omap.h | 1 + board/ti/am43xx/mux.c | 11 ++++ doc/SPI/README.ti_qspi_am43x_test | 76 ++++++++++++++++++++++++++++++ drivers/spi/ti_qspi.c | 33 ++++++++++++- include/configs/am43xx_evm.h | 20 ++++++++ 7 files changed, 142 insertions(+), 4 deletions(-) create mode 100644 doc/SPI/README.ti_qspi_am43x_test

4 20

[U-Boot] [PATCH] Fix problems in chip select selection in imx23, 28 spi code
by Asok Subramanian 08 Jan '14

08 Jan '14

Fix problems in chip select selection in imx23,28 spi code The spi function code for imx23,28 currently does not work for chip select other than 0. This is because the register HW_SSP_CTRL0 is first reset and the code does not load the CS bits again into HW_SSP_CTRL0 after the reset. The proposed fix reloads the CS bits after the reset. Signed-off-by: Asok Subramanian <asok at vyassoft.com> --- drivers/spi/mxs_spi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/spi/mxs_spi.c b/drivers/spi/mxs_spi.c index 3cf7142..15681dc 100644 --- a/drivers/spi/mxs_spi.c +++ b/drivers/spi/mxs_spi.c @@ -32,6 +32,7 @@ struct mxs_spi_slave { uint32_t max_khz; uint32_t mode; struct mxs_ssp_regs *regs; + unsigned int cs; }; static inline struct mxs_spi_slave *to_mxs_slave(struct spi_slave *slave) @@ -74,6 +75,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, mxs_slave->max_khz = max_hz / 1000; mxs_slave->mode = mode; mxs_slave->regs = mxs_ssp_regs_by_bus(bus); + mxs_slave->cs = cs; ssp_regs = mxs_slave->regs; reg = readl(&ssp_regs->hw_ssp_ctrl0); @@ -102,7 +104,7 @@ int spi_claim_bus(struct spi_slave *slave) mxs_reset_block(&ssp_regs->hw_ssp_ctrl0_reg); - writel(SSP_CTRL0_BUS_WIDTH_ONE_BIT, &ssp_regs->hw_ssp_ctrl0); + writel(SSP_CTRL0_BUS_WIDTH_ONE_BIT | (mxs_slave->cs) << MXS_SSP_CHIPSELECT_SHIFT, &ssp_regs->hw_ssp_ctrl0); reg = SSP_CTRL1_SSP_MODE_SPI | SSP_CTRL1_WORD_LENGTH_EIGHT_BITS; reg |= (mxs_slave->mode & SPI_CPOL) ? SSP_CTRL1_POLARITY : 0; -- 1.7.9.5

2 5