September 2012 - U-Boot

[U-Boot] [RFC PATCH 00/17] Convert p1_p2_rdb_pc to new spl
by Scott Wood 26 Nov '12

26 Nov '12

This is based on a merge of top-of-tree plus the 85xx tree and the spl framework branch (it doesn't use the SPL framework code because of size constraints, but I wanted to make sure there were no conflicts with it). Tested on P2020RDB-PC_NAND and P1021RDB-PC_36BIT_NAND. José Miguel Gonçalves (1): Add u-boot-pad.bin target to the Makefile Scott Wood (16): spl: rename u-boot-pad.bin to u-boot-with-spl.bin powerpc: remove .fixup test powerpc/mpc85xx: fix TLB alignment powerpc/mpc8xxx: move LAW code into arch/powerpc/cpu/mpc8xxx spl/mpc85xx: move udelay to cpu code spl: include resetvec and lib8xxx spl/powerpc: introduce CONFIG_SPL_INIT_MINIMAL spl/85xx: new SPL support powerpc/p1_p2_rdb_pc: new SPL support spl/nand: introduce CONFIG_SPL_NAND_MINIMAL spl/nand: config symbol documentation spl/nand: Add minimal-spl driver for Freescale eLBC NAND spl: introduce CONFIG_SPL_TARGET p1_p2_rdb_pc: convert from nand_spl to new spl powerpc/mpc85xx/p2020rdb-pc: fix SPL DDR config ns16550: wait for TENT before initializing Makefile | 24 ++- README | 32 +++- arch/powerpc/cpu/mpc85xx/Makefile | 39 +++-- arch/powerpc/cpu/mpc85xx/cpu.c | 3 +- arch/powerpc/cpu/mpc85xx/cpu_init_nand.c | 19 ++- arch/powerpc/cpu/mpc85xx/start.S | 58 ++++--- arch/powerpc/cpu/mpc85xx/tlb.c | 4 +- arch/powerpc/cpu/mpc85xx/u-boot-spl.lds | 81 ++++++++++ arch/powerpc/cpu/mpc8xxx/Makefile | 17 ++ .../fsl_law.c => arch/powerpc/cpu/mpc8xxx/law.c | 11 +- arch/powerpc/lib/Makefile | 23 ++- board/freescale/p1_p2_rdb_pc/Makefile | 16 ++ board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c | 2 +- .../freescale/p1_p2_rdb_pc/spl_minimal.c | 3 +- board/freescale/p1_p2_rdb_pc/tlb.c | 7 +- doc/README.mpc85xx | 2 +- drivers/misc/Makefile | 1 - drivers/mtd/nand/Makefile | 41 +++-- drivers/mtd/nand/fsl_elbc_spl.c | 168 ++++++++++++++++++++ drivers/serial/ns16550.c | 3 + include/configs/p1_p2_rdb_pc.h | 74 ++++----- nand_spl/board/freescale/common.c | 40 ----- nand_spl/board/freescale/mpc8536ds/Makefile | 2 +- nand_spl/board/freescale/mpc8569mds/Makefile | 2 +- nand_spl/board/freescale/mpc8572ds/Makefile | 2 +- nand_spl/board/freescale/p1010rdb/Makefile | 8 +- nand_spl/board/freescale/p1023rds/Makefile | 8 +- nand_spl/board/freescale/p1_p2_rdb/Makefile | 2 +- nand_spl/board/freescale/p1_p2_rdb_pc/Makefile | 141 ---------------- spl/Makefile | 21 +++ 30 files changed, 542 insertions(+), 312 deletions(-) create mode 100644 arch/powerpc/cpu/mpc85xx/u-boot-spl.lds rename drivers/misc/fsl_law.c => arch/powerpc/cpu/mpc8xxx/law.c (95%) rename nand_spl/board/freescale/p1_p2_rdb_pc/nand_boot.c => board/freescale/p1_p2_rdb_pc/spl_minimal.c (97%) create mode 100644 drivers/mtd/nand/fsl_elbc_spl.c delete mode 100644 nand_spl/board/freescale/common.c delete mode 100644 nand_spl/board/freescale/p1_p2_rdb_pc/Makefile -- 1.7.9.5

8 78

[U-Boot] ERROR: CTL:TIMEOUT - USB porting issue for UBoot on S3C2450
by dongdaking 23 Nov '12

23 Nov '12

Hi, I am porting UBoot on S3C2450 and has an USB issue. Here is an error message: ERROR: CTL:TIMEOUT USB device not responding, giving up (status=20) 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found The problem seems submit_common_msg couldn't get description of USB flash memory device Could I have help? Please tell me if you had this issue before. Thank you for your helping Here is a log data usb start (Re)start USB... USB: INFO: aligned ghcca c3e4f900 DEBUG: USB HC reset_hc usb-smdk2450: ctrl = 0x9F ; DEBUG: OHCI controller usb-smdk2450 state DEBUG: control: 0x0000008f HCFS=operational IE PLE CBSR=3 DEBUG: cmdstatus: 0x00000000 SOC=0 DEBUG: intrstatus: 0x00000044 RHSC SF DEBUG: intrenable: 0x00000053 RHSC UE WDH SO DEBUG: hcca frame #0000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS scanning bus for devices... New Device 0 start 0st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0040 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:64/64 stat:0x0 start 1st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0040 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:64/64 stat:0x0 start 2st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0040 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:64/64 stat:0x0 set address 1 usb_control_msg: request: 0x5, requesttype: 0x0 value 0x1 index 0x0 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000500 0001 0000 0000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x12 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0100 0000 0012 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:18/18 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x8 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0200 0000 0008 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:8/8 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x19 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0200 0000 0019 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:25/25 stat:0x0 get_conf_no 0 Result 25, wLength 25 if 0, ep 0 ##EP epmaxpacketin[1] = 2 set configuration 1 usb_control_msg: request: 0x9, requesttype: 0x0 value 0x1 index 0x0 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000900 0001 0000 0000 INFO: WR:status 0x10000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 new device strings: Mfr=0, Product=1, SerialNumber=0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x300 index 0x0 length 0xFF INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0300 0000 00ff DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:255/255 stat:0x0 USB device number 1 default language ID 0x409 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x301 index 0x409 length 0xFF INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0301 0409 00ff DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:255/255 stat:0x0 Manufacturer Product OHCI Root Hub SerialNumber usb_control_msg: request: 0x6, requesttype: 0xA0 value 0x2900 index 0x0 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000006a0 2900 0000 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0xA0 value 0x2900 index 0x0 length 0x9 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000006a0 2900 0000 0009 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:9/9 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA0 value 0x0 index 0x0 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a0 0000 0000 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x3, requesttype: 0x23 value 0x8 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0008 0001 0000 INFO: WR:portstatus[0] 0x100 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x3, requesttype: 0x23 value 0x8 index 0x2 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0008 0002 0000 INFO: WR:portstatus[1] 0x100 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x1, requesttype: 0x23 value 0x10 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0010 0001 0000 INFO: WR:portstatus[0] 0x10000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x3, requesttype: 0x23 value 0x4 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0004 0001 0000 INFO: WR:portstatus[0] 0x10 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x1, requesttype: 0x23 value 0x14 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0014 0001 0000 INFO: WR:portstatus[0] 0x100000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000103 PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 New Device 1 start 0st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. ERROR: CTL:TIMEOUT DEBUG: submit_common_msg: TO status ff DEBUG: RET(ctlr) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x20 usb_new_device: 64 byte descr usb_control_msg: request: 0x3, requesttype: 0x23 value 0x4 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0004 0001 0000 INFO: WR:portstatus[0] 0x10 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x1, requesttype: 0x23 value 0x14 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0014 0001 0000 INFO: WR:portstatus[0] 0x100000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000103 PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 set address 2 usb_control_msg: request: 0x5, requesttype: 0x0 value 0x2 index 0x0 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 ERROR: submit_control_message: pipesize for pipe 80000000 is zero USB device not accepting new address (error=80000000) usb_control_msg: request: 0x1, requesttype: 0x23 value 0x1 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0001 0001 0000 INFO: WR:portstatus[0] 0x1 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x2 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0002 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found Thank you a lot. Best regards -- View this message in context: http://old.nabble.com/ERROR%3A-CTL%3ATIMEOUT---USB-porting-issue-for-UBoot-… Sent from the Uboot - Users mailing list archive at Nabble.com.

2 1

[U-Boot] [PATCH 0/4] EXYNOS5: Add GPIO numbering feature
by Rajeshwari Shinde 20 Nov '12

20 Nov '12

This patchset adds GPIO numbering feature where pinmux setting can be done just by seding the pin munber and we do not have to remember which bank it belongs to. Rajeshwari Shinde (4): EXYNOS5: Add GPIO unique pin numbering support S5P: GPIO: Add GPIO pin numbering to driver EXYNOS5: Enable GPIO Numbering. EXYNOS: Update pinmux to use gpio numbering arch/arm/cpu/armv7/exynos/pinmux.c | 150 ++++++-------- arch/arm/include/asm/arch-exynos/gpio.h | 351 +++++++++++++++++++++++++++++++ drivers/gpio/s5p_gpio.c | 158 +++++++++++++- include/configs/smdk5250.h | 3 + 4 files changed, 569 insertions(+), 93 deletions(-) -- 1.7.4.4

4 8

[U-Boot] [PATCH 1/4] mx5: cosmetic: Clean up lowlevel_init
by Benoît Thébaudeau 19 Nov '12

19 Nov '12

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau(a)advansee.com> Cc: Stefano Babic <sbabic(a)denx.de> --- .../arch/arm/cpu/armv7/mx5/lowlevel_init.S | 46 ++++++++++---------- 1 file changed, 23 insertions(+), 23 deletions(-) diff --git u-boot-4d3c95f.orig/arch/arm/cpu/armv7/mx5/lowlevel_init.S u-boot-4d3c95f/arch/arm/cpu/armv7/mx5/lowlevel_init.S index 683a7b5..a40b84f 100644 --- u-boot-4d3c95f.orig/arch/arm/cpu/armv7/mx5/lowlevel_init.S +++ u-boot-4d3c95f/arch/arm/cpu/armv7/mx5/lowlevel_init.S @@ -36,9 +36,9 @@ /* reconfigure L2 cache aux control reg */ mov r0, #0xC0 /* tag RAM */ add r0, r0, #0x4 /* data RAM */ - orr r0, r0, #(1 << 24) /* disable write allocate delay */ - orr r0, r0, #(1 << 23) /* disable write allocate combine */ - orr r0, r0, #(1 << 22) /* disable write allocate */ + orr r0, r0, #1 << 24 /* disable write allocate delay */ + orr r0, r0, #1 << 23 /* disable write allocate combine */ + orr r0, r0, #1 << 22 /* disable write allocate */ #if defined(CONFIG_MX51) ldr r1, =0x0 @@ -46,7 +46,7 @@ cmp r3, #0x10 /* disable write combine for TO 2 and lower revs */ - orrls r0, r0, #(1 << 25) + orrls r0, r0, #1 << 25 #endif mcr 15, 1, r0, c9, c0, 2 @@ -247,9 +247,9 @@ movhi r1, #0 #else mov r1, #0 - #endif str r1, [r0, #CLKCTL_CACRR] + /* Switch ARM back to PLL 1 */ mov r1, #0 str r1, [r0, #CLKCTL_CCSR] @@ -288,9 +288,9 @@ /* Switch peripheral to PLL2 */ ldr r0, =CCM_BASE_ADDR ldr r1, =0x00808145 - orr r1, r1, #(2 << 10) - orr r1, r1, #(0 << 16) - orr r1, r1, #(1 << 19) + orr r1, r1, #2 << 10 + orr r1, r1, #0 << 16 + orr r1, r1, #1 << 19 str r1, [r0, #CLKCTL_CBCDR] ldr r1, =0x00016154 @@ -331,10 +331,10 @@ ENTRY(lowlevel_init) #if defined(CONFIG_MX51) ldr r0, =GPIO1_BASE_ADDR ldr r1, [r0, #0x0] - orr r1, r1, #(1 << 23) + orr r1, r1, #1 << 23 str r1, [r0, #0x0] ldr r1, [r0, #0x4] - orr r1, r1, #(1 << 23) + orr r1, r1, #1 << 23 str r1, [r0, #0x4] #endif @@ -351,16 +351,16 @@ ENTRY(lowlevel_init) ENDPROC(lowlevel_init) /* Board level setting value */ -W_DP_OP_864: .word DP_OP_864 -W_DP_MFD_864: .word DP_MFD_864 -W_DP_MFN_864: .word DP_MFN_864 -W_DP_MFN_800_DIT: .word DP_MFN_800_DIT -W_DP_OP_800: .word DP_OP_800 -W_DP_MFD_800: .word DP_MFD_800 -W_DP_MFN_800: .word DP_MFN_800 -W_DP_OP_665: .word DP_OP_665 -W_DP_MFD_665: .word DP_MFD_665 -W_DP_MFN_665: .word DP_MFN_665 -W_DP_OP_216: .word DP_OP_216 -W_DP_MFD_216: .word DP_MFD_216 -W_DP_MFN_216: .word DP_MFN_216 +W_DP_OP_864: .word DP_OP_864 +W_DP_MFD_864: .word DP_MFD_864 +W_DP_MFN_864: .word DP_MFN_864 +W_DP_MFN_800_DIT: .word DP_MFN_800_DIT +W_DP_OP_800: .word DP_OP_800 +W_DP_MFD_800: .word DP_MFD_800 +W_DP_MFN_800: .word DP_MFN_800 +W_DP_OP_665: .word DP_OP_665 +W_DP_MFD_665: .word DP_MFD_665 +W_DP_MFN_665: .word DP_MFN_665 +W_DP_OP_216: .word DP_OP_216 +W_DP_MFD_216: .word DP_MFD_216 +W_DP_MFN_216: .word DP_MFN_216

3 21

[U-Boot] [PATCH] nand: Extending the nand_ecclayout struct based on Linux 3.5
by Charles Hardin 16 Nov '12

16 Nov '12

NANDs with large page sizes are getting oob ares of 218 and 224 so the eccpos field needs to support these larger areas since BCH ECC correction with 24-bit over 1024 bytes will use 168 bytes of the oob for ECC and is required for current MLC NAND parts circa 2012. Signed-off-by: Charles Hardin <ckhardin(a)exablox.com> diff --git a/include/linux/mtd/mtd-abi.h b/include/linux/mtd/mtd-abi.h index 1e7a18f..c321d6b 100644 --- a/include/linux/mtd/mtd-abi.h +++ b/include/linux/mtd/mtd-abi.h @@ -116,16 +116,17 @@ struct nand_oobfree { uint32_t length; }; -#define MTD_MAX_OOBFREE_ENTRIES 8 +#define MTD_MAX_OOBFREE_ENTRIES_LARGE 32 +#define MTD_MAX_ECCPOS_ENTRIES_LARGE 448 /* * ECC layout control structure. Exported to userspace for * diagnosis and to allow creation of raw images */ struct nand_ecclayout { uint32_t eccbytes; - uint32_t eccpos[128]; + uint32_t eccpos[MTD_MAX_ECCPOS_ENTRIES_LARGE]; uint32_t oobavail; - struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES]; + struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES_LARGE]; }; /**

2 2

[U-Boot] [PATCH] driver/mtd:IFC NAND:Initialise internal SRAM before any write
by Prabhakar Kushwaha 16 Nov '12

16 Nov '12

IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for SRAM i.e. "byte select" is not supported. Hence Read Modify Write is implemented in IFC for any "system side write" into sram buffer. Reading an uninitialized memory results in ECC Error from sram wrapper. Hence we must initialize/prefill SRAM buffer by any data before writing anything in SRAM from system side. To initialize SRAM user can use "READID" NAND command with read bytes equal to SRAM size. It will be a one time activity post boot Signed-off-by: Prabhakar Kushwaha <prabhakar(a)freescale.com> --- Based upon git://git.denx.de/u-boot.git (branch master) This patchs depends upon following patch http://patchwork.ozlabs.org/patch/178332/ drivers/mtd/nand/fsl_ifc_nand.c | 62 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 61 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index a518526..140fdc7 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -30,6 +30,7 @@ #include <asm/errno.h> #include <asm/fsl_ifc.h> +#define FSL_IFC_V1_1_0 0x01010000 #define MAX_BANKS 4 #define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */ @@ -738,11 +739,66 @@ static void fsl_ifc_select_chip(struct mtd_info *mtd, int chip) { } +static void fsl_ifc_sram_init() +{ + struct fsl_ifc *ifc = ifc_ctrl->regs; + uint32_t cs = 0, csor = 0, csor_8k = 0, csor_ext = 0; + long long end_tick; + + cs = ifc_ctrl->cs_nand >> IFC_NAND_CSEL_SHIFT; + + /* Save CSOR and CSOR_ext */ + csor = in_be32(&ifc_ctrl->regs->csor_cs[cs].csor); + csor_ext = in_be32(&ifc_ctrl->regs->csor_cs[cs].csor_ext); + + /* chage PageSize 8K and SpareSize 1K*/ + csor_8k = (csor & ~(CSOR_NAND_PGS_MASK)) | 0x0018C000; + out_be32(&ifc_ctrl->regs->csor_cs[cs].csor, csor_8k); + out_be32(&ifc_ctrl->regs->csor_cs[cs].csor_ext, 0x0000400); + + /* READID */ + out_be32(&ifc->ifc_nand.nand_fir0, + (IFC_FIR_OP_CMD0 << IFC_NAND_FIR0_OP0_SHIFT) | + (IFC_FIR_OP_UA << IFC_NAND_FIR0_OP1_SHIFT) | + (IFC_FIR_OP_RB << IFC_NAND_FIR0_OP2_SHIFT)); + out_be32(&ifc->ifc_nand.nand_fcr0, + NAND_CMD_READID << IFC_NAND_FCR0_CMD0_SHIFT); + out_be32(&ifc->ifc_nand.row3, 0x0); + + out_be32(&ifc->ifc_nand.nand_fbcr, 0x0); + + /* Program ROW0/COL0 */ + out_be32(&ifc->ifc_nand.row0, 0x0); + out_be32(&ifc->ifc_nand.col0, 0x0); + + /* set the chip select for NAND Transaction */ + out_be32(&ifc->ifc_nand.nand_csel, ifc_ctrl->cs_nand); + + /* start read seq */ + out_be32(&ifc->ifc_nand.nandseq_strt, IFC_NAND_SEQ_STRT_FIR_STRT); + + /* wait for NAND Machine complete flag or timeout */ + end_tick = usec2ticks(IFC_TIMEOUT_MSECS * 1000) + get_ticks(); + + while (end_tick > get_ticks()) { + ifc_ctrl->status = in_be32(&ifc->ifc_nand.nand_evter_stat); + + if (ifc_ctrl->status & IFC_NAND_EVTER_STAT_OPC) + break; + } + + out_be32(&ifc->ifc_nand.nand_evter_stat, ifc_ctrl->status); + + /* Restore CSOR and CSOR_ext */ + out_be32(&ifc_ctrl->regs->csor_cs[cs].csor, csor); + out_be32(&ifc_ctrl->regs->csor_cs[cs].csor_ext, csor_ext); +} + int board_nand_init(struct nand_chip *nand) { struct fsl_ifc_mtd *priv; struct nand_ecclayout *layout; - uint32_t cspr = 0, csor = 0; + uint32_t cspr = 0, csor = 0, ver = 0; if (!ifc_ctrl) { fsl_ifc_ctrl_init(); @@ -860,5 +916,9 @@ int board_nand_init(struct nand_chip *nand) nand->ecc.mode = NAND_ECC_SOFT; } + ver = in_be32(&ifc_ctrl->regs->ifc_rev); + if (ver == FSL_IFC_V1_1_0) + fsl_ifc_sram_init(); + return 0; } -- 1.7.9.5

2 1

[U-Boot] [PATCH] cosmetic: Reference nand monitor commands in U-Boot README
by Karl O. Pinc 15 Nov '12

15 Nov '12

Signed-off-by: Karl O. Pinc <kop(a)meme.com> --- README | 1 + 1 files changed, 1 insertions(+), 0 deletions(-) diff --git a/README b/README index fb9d904..6bb5992 100644 --- a/README +++ b/README @@ -3725,6 +3725,7 @@ saveenv - save environment variables to persistent storage protect - enable or disable FLASH write protection erase - erase FLASH memory flinfo - print FLASH memory information +nand - NAND memory operations (see doc/README.nand) bdinfo - print Board Info structure iminfo - print header information for application image coninfo - print console devices and informations -- 1.7.2.5

3 3

[U-Boot] [PATCH 2/2] usb: r8a66597: Switched from variable to only macro
by Nobuhiro Iwamatsu 15 Nov '12

15 Nov '12

Some variables are initialized with a value defined by macro. This was changed to use the macro directly. And the variable not to use deleted it. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu(a)nigauri.org> --- drivers/usb/host/r8a66597-hcd.c | 15 +++++---------- 1 files changed, 5 insertions(+), 10 deletions(-) diff --git a/drivers/usb/host/r8a66597-hcd.c b/drivers/usb/host/r8a66597-hcd.c index ab1b8d0..f5a7e30 100644 --- a/drivers/usb/host/r8a66597-hcd.c +++ b/drivers/usb/host/r8a66597-hcd.c @@ -31,9 +31,6 @@ #endif static const char hcd_name[] = "r8a66597_hcd"; -static unsigned short clock = CONFIG_R8A66597_XTAL; -static unsigned short vif = CONFIG_R8A66597_LDRV; -static unsigned short endian = CONFIG_R8A66597_ENDIAN; static struct r8a66597 gr8a66597; static void get_hub_data(struct usb_device *dev, u16 *hub_devnum, u16 *hubport) @@ -96,7 +93,7 @@ static int r8a66597_clock_enable(struct r8a66597 *r8a66597) } } while ((tmp & USBE) != USBE); r8a66597_bclr(r8a66597, USBE, SYSCFG0); - r8a66597_mdfy(r8a66597, clock, XTAL, SYSCFG0); + r8a66597_mdfy(r8a66597, CONFIG_R8A66597_XTAL, XTAL, SYSCFG0); i = 0; r8a66597_bset(r8a66597, XCKE, SYSCFG0); @@ -162,7 +159,7 @@ static int enable_controller(struct r8a66597 *r8a66597) if (ret < 0) return ret; - r8a66597_bset(r8a66597, vif & LDRV, PINCFG); + r8a66597_bset(r8a66597, CONFIG_R8A66597_LDRV & LDRV, PINCFG); r8a66597_bset(r8a66597, USBE, SYSCFG0); r8a66597_bset(r8a66597, INTL, SOFCFG); @@ -170,9 +167,9 @@ static int enable_controller(struct r8a66597 *r8a66597) r8a66597_write(r8a66597, 0, INTENB1); r8a66597_write(r8a66597, 0, INTENB2); - r8a66597_bset(r8a66597, endian & BIGEND, CFIFOSEL); - r8a66597_bset(r8a66597, endian & BIGEND, D0FIFOSEL); - r8a66597_bset(r8a66597, endian & BIGEND, D1FIFOSEL); + r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, CFIFOSEL); + r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, D0FIFOSEL); + r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, D1FIFOSEL); r8a66597_bset(r8a66597, TRNENSEL, SOFCFG); for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++) @@ -673,7 +670,6 @@ static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, int stat = 0; __u16 bmRType_bReq; __u16 wValue; - __u16 wIndex; __u16 wLength; unsigned char data[32]; @@ -686,7 +682,6 @@ static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe, bmRType_bReq = cmd->requesttype | (cmd->request << 8); wValue = cpu_to_le16 (cmd->value); - wIndex = cpu_to_le16 (cmd->index); wLength = cpu_to_le16 (cmd->length); switch (bmRType_bReq) { -- 1.7.9.1

2 3

[U-Boot] mx53loco: Fix build error when CONFIG_VIDEO is disabled
by Vikram Narayanan 14 Nov '12

14 Nov '12

The inclusion of LCD patch into mx51evk breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186(a)gmail.com> Cc: Fabio Estevam <fabio.estevam(a)freescale.com> Cc: Stefano Babic <sbabic(a)denx.de> --- board/freescale/mx53loco/Makefile | 4 +- board/freescale/mx53loco/mx53loco.c | 78 ++--------------------- board/freescale/mx53loco/mx53loco_video.c | 96 +++++++++++++++++++++++++++++ 3 files changed, 106 insertions(+), 72 deletions(-) create mode 100644 board/freescale/mx53loco/mx53loco_video.c diff --git a/board/freescale/mx53loco/Makefile b/board/freescale/mx53loco/Makefile index a6ea939..f92c928 100644 --- a/board/freescale/mx53loco/Makefile +++ b/board/freescale/mx53loco/Makefile @@ -22,8 +22,10 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS := mx53loco.o +COBJS-y += mx53loco.o +COBJS-$(CONFIG_VIDEO) += mx53loco_video.o +COBJS := $(COBJS-y) SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) SOBJS := $(addprefix $(obj),$(SOBJS)) diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c index d8e027c..d494716 100644 --- a/board/freescale/mx53loco/mx53loco.c +++ b/board/freescale/mx53loco/mx53loco.c @@ -39,10 +39,6 @@ #include <pmic.h> #include <dialog_pmic.h> #include <fsl_pmic.h> -#include <linux/fb.h> -#include <ipu_pixfmt.h> - -#define MX53LOCO_LCD_POWER (2 * 32 + 24) /* GPIO3_24 */ DECLARE_GLOBAL_DATA_PTR; @@ -406,75 +402,13 @@ static void clock_1GHz(void) printf("CPU: Switch DDR clock to 400MHz failed\n"); } -static struct fb_videomode claa_wvga = { - .name = "CLAA07LC0ACW", - .refresh = 57, - .xres = 800, - .yres = 480, - .pixclock = 37037, - .left_margin = 40, - .right_margin = 60, - .upper_margin = 10, - .lower_margin = 10, - .hsync_len = 20, - .vsync_len = 10, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED -}; - -void lcd_iomux(void) -{ - mxc_request_iomux(MX53_PIN_DI0_DISP_CLK, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DI0_PIN15, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DI0_PIN2, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DI0_PIN3, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT0, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT1, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT2, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT3, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT4, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT5, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT6, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT7, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT8, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT9, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT10, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT11, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT12, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT13, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT14, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT15, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT16, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT17, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT18, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT19, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT20, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT21, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT22, IOMUX_CONFIG_ALT0); - mxc_request_iomux(MX53_PIN_DISP0_DAT23, IOMUX_CONFIG_ALT0); - - /* Turn on GPIO backlight */ - mxc_request_iomux(MX53_PIN_EIM_D24, IOMUX_CONFIG_ALT1); - gpio_direction_output(MX53LOCO_LCD_POWER, 1); - - /* Turn on display contrast */ - mxc_request_iomux(MX53_PIN_GPIO_1, IOMUX_CONFIG_ALT1); - gpio_direction_output(IOMUX_TO_GPIO(MX53_PIN_GPIO_1), 1); -} - -void lcd_enable(void) -{ - int ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565); - if (ret) - printf("LCD cannot be configured: %d\n", ret); -} - int board_early_init_f(void) { setup_iomux_uart(); setup_iomux_fec(); - lcd_iomux(); - +#ifdef CONFIG_VIDEO + setup_iomux_lcd(); +#endif return 0; } @@ -500,8 +434,9 @@ int board_late_init(void) clock_1GHz(); print_cpuinfo(); +#ifdef CONFIG_VIDEO setenv("stdout", "serial"); - +#endif return 0; } #endif @@ -512,8 +447,9 @@ int board_init(void) mxc_set_sata_internal_clock(); +#ifdef CONFIG_VIDEO lcd_enable(); - +#endif return 0; } diff --git a/board/freescale/mx53loco/mx53loco_video.c b/board/freescale/mx53loco/mx53loco_video.c new file mode 100644 index 0000000..cc434e4 --- /dev/null +++ b/board/freescale/mx53loco/mx53loco_video.c @@ -0,0 +1,96 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Fabio Estevam <fabio.estevam(a)freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + + */ + +#include <common.h> +#include <linux/list.h> +#include <asm/gpio.h> +#include <asm/arch/iomux.h> +#include <linux/fb.h> +#include <ipu_pixfmt.h> + +#define MX53LOCO_LCD_POWER (2 * 32 + 24) /* GPIO3_24 */ + +static struct fb_videomode claa_wvga = { + .name = "CLAA07LC0ACW", + .refresh = 57, + .xres = 800, + .yres = 480, + .pixclock = 37037, + .left_margin = 40, + .right_margin = 60, + .upper_margin = 10, + .lower_margin = 10, + .hsync_len = 20, + .vsync_len = 10, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED +}; + +void setup_iomux_lcd(void) +{ + mxc_request_iomux(MX53_PIN_DI0_DISP_CLK, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DI0_PIN15, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DI0_PIN2, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DI0_PIN3, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT0, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT1, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT2, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT3, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT4, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT5, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT6, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT7, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT8, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT9, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT10, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT11, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT12, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT13, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT14, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT15, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT16, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT17, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT18, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT19, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT20, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT21, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT22, IOMUX_CONFIG_ALT0); + mxc_request_iomux(MX53_PIN_DISP0_DAT23, IOMUX_CONFIG_ALT0); + + /* Turn on GPIO backlight */ + mxc_request_iomux(MX53_PIN_EIM_D24, IOMUX_CONFIG_ALT1); + gpio_direction_output(MX53LOCO_LCD_POWER, 1); + + /* Turn on display contrast */ + mxc_request_iomux(MX53_PIN_GPIO_1, IOMUX_CONFIG_ALT1); + gpio_direction_output(IOMUX_TO_GPIO(MX53_PIN_GPIO_1), 1); +} + +void lcd_enable(void) +{ + int ret = ipuv3_fb_init(&claa_wvga, 0, IPU_PIX_FMT_RGB565); + if (ret) + printf("LCD cannot be configured: %d\n", ret); +} + -- 1.7.4.1

2 2

[U-Boot] mx51evk: Fix build error when CONFIG_VIDEO is disabled
by Vikram Narayanan 14 Nov '12

14 Nov '12

The inclusion of LCD patch into mx51evk breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186(a)gmail.com> Cc: Fabio Estevam <fabio.estevam(a)freescale.com> Cc: Stefano Babic <sbabic(a)denx.de> --- board/freescale/mx51evk/Makefile | 4 +- board/freescale/mx51evk/mx51evk.c | 65 +++--------------------- board/freescale/mx51evk/mx51evk_video.c | 83 +++++++++++++++++++++++++++++++ 3 files changed, 93 insertions(+), 59 deletions(-) create mode 100644 board/freescale/mx51evk/mx51evk_video.c diff --git a/board/freescale/mx51evk/Makefile b/board/freescale/mx51evk/Makefile index 470588e..9ded43f 100644 --- a/board/freescale/mx51evk/Makefile +++ b/board/freescale/mx51evk/Makefile @@ -23,8 +23,10 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS := mx51evk.o +COBJS-y += mx51evk.o +COBJS-$(CONFIG_VIDEO) += mx51evk_video.o +COBJS := $(COBJS-y) SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) SOBJS := $(addprefix $(obj),$(SOBJS)) diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 514a7ac..2b82c8e 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -36,12 +36,6 @@ #include <fsl_pmic.h> #include <mc13892.h> #include <usb/ehci-fsl.h> -#include <linux/fb.h> -#include <ipu_pixfmt.h> - -#define MX51EVK_LCD_3V3 (3 * 32 + 9) /* GPIO4_9 */ -#define MX51EVK_LCD_5V (3 * 32 + 10) /* GPIO4_10 */ -#define MX51EVK_LCD_BACKLIGHT (2 * 32 + 4) /* GPIO3_4 */ DECLARE_GLOBAL_DATA_PTR; @@ -459,53 +453,6 @@ int board_mmc_init(bd_t *bis) } #endif -static struct fb_videomode claa_wvga = { - .name = "CLAA07LC0ACW", - .refresh = 57, - .xres = 800, - .yres = 480, - .pixclock = 37037, - .left_margin = 40, - .right_margin = 60, - .upper_margin = 10, - .lower_margin = 10, - .hsync_len = 20, - .vsync_len = 10, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED -}; - -void lcd_iomux(void) -{ - /* DI2_PIN15 */ - mxc_request_iomux(MX51_PIN_DI_GP4, IOMUX_CONFIG_ALT4); - - /* Pad settings for MX51_PIN_DI2_DISP_CLK */ - mxc_iomux_set_pad(MX51_PIN_DI2_DISP_CLK, PAD_CTL_HYS_NONE | - PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | - PAD_CTL_DRV_MAX | PAD_CTL_SRE_SLOW); - - /* Turn on 3.3V voltage for LCD */ - mxc_request_iomux(MX51_PIN_CSI2_D12, IOMUX_CONFIG_ALT3); - gpio_direction_output(MX51EVK_LCD_3V3, 1); - - /* Turn on 5V voltage for LCD */ - mxc_request_iomux(MX51_PIN_CSI2_D13, IOMUX_CONFIG_ALT3); - gpio_direction_output(MX51EVK_LCD_5V, 1); - - /* Turn on GPIO backlight */ - mxc_request_iomux(MX51_PIN_DI1_D1_CS, IOMUX_CONFIG_ALT4); - mxc_iomux_set_input(MX51_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT, - INPUT_CTL_PATH1); - gpio_direction_output(MX51EVK_LCD_BACKLIGHT, 1); -} - -void lcd_enable(void) -{ - int ret = ipuv3_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565); - if (ret) - printf("LCD cannot be configured: %d\n", ret); -} int board_early_init_f(void) { @@ -514,8 +461,9 @@ int board_early_init_f(void) #ifdef CONFIG_USB_EHCI_MX5 setup_usb_h1(); #endif - lcd_iomux(); - +#ifdef CONFIG_VIDEO + setup_iomux_lcd(); +#endif return 0; } @@ -523,9 +471,9 @@ int board_init(void) { /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; - +#ifdef CONFIG_VIDEO lcd_enable(); - +#endif return 0; } @@ -536,8 +484,9 @@ int board_late_init(void) setup_iomux_spi(); power_init(); #endif +#ifdef CONFIG_VIDEO setenv("stdout", "serial"); - +#endif return 0; } #endif diff --git a/board/freescale/mx51evk/mx51evk_video.c b/board/freescale/mx51evk/mx51evk_video.c new file mode 100644 index 0000000..e316e4c --- /dev/null +++ b/board/freescale/mx51evk/mx51evk_video.c @@ -0,0 +1,83 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * Fabio Estevam <fabio.estevam(a)freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + + */ + +#include <common.h> +#include <linux/list.h> +#include <asm/gpio.h> +#include <asm/arch/iomux.h> +#include <linux/fb.h> +#include <ipu_pixfmt.h> + +#define MX51EVK_LCD_3V3 (3 * 32 + 9) /* GPIO4_9 */ +#define MX51EVK_LCD_5V (3 * 32 + 10) /* GPIO4_10 */ +#define MX51EVK_LCD_BACKLIGHT (2 * 32 + 4) /* GPIO3_4 */ + +static struct fb_videomode claa_wvga = { + .name = "CLAA07LC0ACW", + .refresh = 57, + .xres = 800, + .yres = 480, + .pixclock = 37037, + .left_margin = 40, + .right_margin = 60, + .upper_margin = 10, + .lower_margin = 10, + .hsync_len = 20, + .vsync_len = 10, + .sync = 0, + .vmode = FB_VMODE_NONINTERLACED +}; + +void setup_iomux_lcd(void) +{ + /* DI2_PIN15 */ + mxc_request_iomux(MX51_PIN_DI_GP4, IOMUX_CONFIG_ALT4); + + /* Pad settings for MX51_PIN_DI2_DISP_CLK */ + mxc_iomux_set_pad(MX51_PIN_DI2_DISP_CLK, PAD_CTL_HYS_NONE | + PAD_CTL_PKE_ENABLE | PAD_CTL_PUE_KEEPER | + PAD_CTL_DRV_MAX | PAD_CTL_SRE_SLOW); + + /* Turn on 3.3V voltage for LCD */ + mxc_request_iomux(MX51_PIN_CSI2_D12, IOMUX_CONFIG_ALT3); + gpio_direction_output(MX51EVK_LCD_3V3, 1); + + /* Turn on 5V voltage for LCD */ + mxc_request_iomux(MX51_PIN_CSI2_D13, IOMUX_CONFIG_ALT3); + gpio_direction_output(MX51EVK_LCD_5V, 1); + + /* Turn on GPIO backlight */ + mxc_request_iomux(MX51_PIN_DI1_D1_CS, IOMUX_CONFIG_ALT4); + mxc_iomux_set_input(MX51_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT, + INPUT_CTL_PATH1); + gpio_direction_output(MX51EVK_LCD_BACKLIGHT, 1); +} + +void lcd_enable(void) +{ + int ret = ipuv3_fb_init(&claa_wvga, 1, IPU_PIX_FMT_RGB565); + if (ret) + printf("LCD cannot be configured: %d\n", ret); +} + -- 1.7.4.1

2 4