July 2012 - U-Boot

[U-Boot] [PATCH 1/2] part_dos: allocate cacheline aligned buffers
by Thierry Reding 06 Nov '12

06 Nov '12

Some hardware requires the data buffers to be cacheline-aligned to make sure DMA operations can be properly executed. This patch uses the ALLOC_CACHE_ALIGN_BUFFER macro to allocate buffers with proper alignment. The same was already done for EFI partitions in commit f75dd58 "part_efi: dcache: allocate cacheline aligned buffers". Signed-off-by: Thierry Reding <thierry.reding(a)avionic-design.de> --- This fixes boot failures on Avionic Design Plutux and Medcom boards. disk/part_dos.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/disk/part_dos.c b/disk/part_dos.c index b5bcb37..c028aaf 100644 --- a/disk/part_dos.c +++ b/disk/part_dos.c @@ -87,7 +87,7 @@ static int test_block_type(unsigned char *buffer) int test_part_dos (block_dev_desc_t *dev_desc) { - unsigned char buffer[dev_desc->blksz]; + ALLOC_CACHE_ALIGN_BUFFER(unsigned char, buffer, dev_desc->blksz); if ((dev_desc->block_read(dev_desc->dev, 0, 1, (ulong *) buffer) != 1) || (buffer[DOS_PART_MAGIC_OFFSET + 0] != 0x55) || @@ -102,7 +102,7 @@ int test_part_dos (block_dev_desc_t *dev_desc) static void print_partition_extended (block_dev_desc_t *dev_desc, int ext_part_sector, int relative, int part_num) { - unsigned char buffer[dev_desc->blksz]; + ALLOC_CACHE_ALIGN_BUFFER(unsigned char, buffer, dev_desc->blksz); dos_partition_t *pt; int i; @@ -166,7 +166,7 @@ static int get_partition_info_extended (block_dev_desc_t *dev_desc, int ext_part int relative, int part_num, int which_part, disk_partition_t *info) { - unsigned char buffer[dev_desc->blksz]; + ALLOC_CACHE_ALIGN_BUFFER(unsigned char, buffer, dev_desc->blksz); dos_partition_t *pt; int i; -- 1.7.10

5 20

[U-Boot] [PATCH 00/14] Nokia RX-51 support
by Pali Rohár 02 Nov '12

02 Nov '12

This patch series add support for new board Nokia RX-51 (aka N900). Last two patches adding on screen bootmenu support. This series supersedes the last sent version. Pali Rohár (14): arm,omap3: Define save_boot_params in lowlevel_init.S for SPL only arm: Optionally use existing atags in bootm.c Add power bus message definitions in twl4030.h Fix function readline in main.c cfb_console: Fix function console_scrollup cfb_console: Add function console_clear and console_clear_line cfb_console: Add functions for moving with cursor cfb_console: Add support for some ANSI terminal escape codes New command clear: Clear the ANSI terminal New config variable CONFIG_MENUCMD New config variable CONFIG_PREMONITOR New board support: Nokia RX-51 aka N900 New command bootmenu: ANSI terminal Boot Menu support RX-51: Add support for bootmenu README | 2 + arch/arm/cpu/armv7/omap3/lowlevel_init.S | 4 +- arch/arm/lib/bootm.c | 39 +++- board/nokia/rx51/Makefile | 46 ++++ board/nokia/rx51/lowlevel_init.S | 79 ++++++ board/nokia/rx51/rx51.c | 381 ++++++++++++++++++++++++++++++ board/nokia/rx51/rx51.h | 378 +++++++++++++++++++++++++++++ boards.cfg | 1 + common/Makefile | 2 + common/cmd_bootmenu.c | 366 ++++++++++++++++++++++++++++ common/cmd_clear.c | 42 ++++ common/env_common.c | 3 + common/main.c | 89 ++++++- drivers/video/cfb_console.c | 346 +++++++++++++++++++++++++-- include/common.h | 20 ++ include/config_cmd_all.h | 2 + include/configs/nokia_rx51.h | 375 +++++++++++++++++++++++++++++ include/twl4030.h | 98 ++++++++ 18 files changed, 2233 insertions(+), 40 deletions(-) create mode 100644 board/nokia/rx51/Makefile create mode 100644 board/nokia/rx51/lowlevel_init.S create mode 100644 board/nokia/rx51/rx51.c create mode 100644 board/nokia/rx51/rx51.h create mode 100644 common/cmd_bootmenu.c create mode 100644 common/cmd_clear.c create mode 100644 include/configs/nokia_rx51.h -- 1.7.5.4

12 219

[U-Boot] [PATCH v4 0/6] tegra: Add NAND flash support
by Simon Glass 02 Nov '12

02 Nov '12

This series adds NAND flash support to Tegra and enables it on Seaboard. Included here is a proposed device tree binding with most of the properties private to "nvidia,". The binding includes information about the NAND controller as well as the connected NAND device. The Seaboard has a Hynix HY27UF4G2B. The driver supports ECC-based access and uses DMA and NAND acceleration features of the Tegra SOC to provide access at reasonable speed. Changes in v2: - Add new patch to align default buffers in nand_base - Added comment about the behaviour of the 'resp' register - Call set_bus_width_page_size() at init to report errors earlier - Change set_bus_width_page_size() to return an error when needed - Change timing structure member to u32 to match device tree - Check for supported bus width in board_nand_init() - Fix tegra nand header file to remove BIT defines - Implement a dummy nand_select_chip() instead of nand_hwcontro() - Make nand_command() display an error on an unknown command - Minor code tidy-ups in driver for style - Move cache logic into a separate dma_prepare() function - Remove CMD_TRANS_SIZE_BYTESx enum - Remove space after casts - Remove use of 'register' variables - Rename struct nand_info to struct nand_drv to avoid nand_info_t confusion - Support 4096 byte page devices, drop 1024 and 2048 - Tidy up nand_waitfor_cmd_completion() logic - Update NAND binding to add "nvidia," prefix - Use s32 for device tree integer values Changes in v3: - Add reg property for unit address (should be used for chip select) - Change note in fdt binding about the need for a hardware-specific binding - Fix up typos in fdt binding, and rename the file - Update fdt binding to make everything Nvidia-specific Changes in v4: - Align buffer length to cache line size in dma_prepare() - Fix "Write Page 0x0 timeout with ECC" error on 4.4.1 - Fix the issue that read_byte can read at most 4 times - Get some information from Read ID data instead of from device tree - In nand_command, set NAND_CMD_RNDOUT as unsupported command - Modify eccoob layout - Move to using CONFIG_SYS_NAND_SELF_INIT - Remove "DEFAULT" from comment because that function is not default - Remove fdt bindings related to page structure - Remove local read_buf and write_buf functions - Remove some fields in fdt_nand structure - Rename CONFIG_TEGRA2_NAND to CONFIG_TEGRA_NAND - Rename variables my_* as our_* - Use virt_to_phys() when filling address register Jim Lin (1): tegra: nand: Add Tegra NAND driver Simon Glass (5): nand: Try to align the default buffers tegra: Add NAND support to funcmux tegra: fdt: Add NAND controller binding and definitions tegra: fdt: Add NAND definitions to fdt tegra: Enable NAND on Seaboard arch/arm/cpu/tegra20-common/funcmux.c | 7 + arch/arm/dts/tegra20.dtsi | 7 + arch/arm/include/asm/arch-tegra20/funcmux.h | 3 + arch/arm/include/asm/arch-tegra20/tegra20.h | 1 + board/nvidia/dts/tegra20-seaboard.dts | 10 + .../nand/nvidia,tegra20-nand.txt | 53 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/nand_base.c | 3 +- drivers/mtd/nand/tegra_nand.c | 1026 ++++++++++++++++++++ drivers/mtd/nand/tegra_nand.h | 257 +++++ include/configs/seaboard.h | 9 + include/configs/tegra20-common.h | 2 + include/fdtdec.h | 1 + include/linux/mtd/nand.h | 7 +- lib/fdtdec.c | 1 + 15 files changed, 1384 insertions(+), 4 deletions(-) create mode 100644 doc/device-tree-bindings/nand/nvidia,tegra20-nand.txt create mode 100644 drivers/mtd/nand/tegra_nand.c create mode 100644 drivers/mtd/nand/tegra_nand.h -- 1.7.7.3

7 29

[U-Boot] [PATCH 0/5] Support for qualcomm msm7630 board
by mohamed.haneef＠lntinfotech.com 26 Oct '12

26 Oct '12

From: Mohamed Haneef <mohamed.haneef(a)lntinfotech.com> This is a patch series for msm7630 board. The Patches contain the following support * low speed uart for msm7630 * interprocessor communication * msm7630 soc * msm7630 surf board Mohamed Haneef (5): msm7x30: Add support for low speed uart on msm7x30 msm7x30: Add support for interprocessor communication msm7x30: Add support for Qualcomm msm7630 soc Add support for mmc read and writes msm7x30: Add support for msm7630_surf board arch/arm/cpu/armv7/msm7630/Makefile | 59 +++ arch/arm/cpu/armv7/msm7630/acpuclock.c | 328 +++++++++++++ arch/arm/cpu/armv7/msm7630/board.c | 58 +++ arch/arm/cpu/armv7/msm7630/config.mk | 1 + arch/arm/cpu/armv7/msm7630/gpio.c | 229 +++++++++ arch/arm/cpu/armv7/msm7630/lowlevel_init.S | 626 +++++++++++++++++++++++++ arch/arm/cpu/armv7/msm7630/timer.c | 148 ++++++ arch/arm/include/asm/arch-msm7630/adm.h | 28 ++ arch/arm/include/asm/arch-msm7630/gpio.h | 47 ++ arch/arm/include/asm/arch-msm7630/gpio_hw.h | 168 +++++++ arch/arm/include/asm/arch-msm7630/iomap.h | 96 ++++ arch/arm/include/asm/arch-msm7630/mmc.h | 399 ++++++++++++++++ arch/arm/include/asm/arch-msm7630/proc_comm.h | 42 ++ arch/arm/include/asm/arch-msm7630/sys_proto.h | 29 ++ board/qcom/msm7630_surf/Makefile | 55 +++ board/qcom/msm7630_surf/msm7630_surf.c | 155 ++++++ board/qcom/msm7630_surf/msm7630_surf.h | 30 ++ boards.cfg | 1 + drivers/misc/Makefile | 1 + drivers/misc/msm_proc_comm.c | 303 ++++++++++++ drivers/mmc/Makefile | 1 + drivers/mmc/qc_mmc.c | 584 +++++++++++++++++++++++ drivers/serial/Makefile | 1 + drivers/serial/serial_msm_uart.c | 206 ++++++++ include/configs/msm7630_surf.h | 131 +++++ 25 files changed, 3726 insertions(+), 0 deletions(-) create mode 100644 arch/arm/cpu/armv7/msm7630/Makefile create mode 100644 arch/arm/cpu/armv7/msm7630/acpuclock.c create mode 100644 arch/arm/cpu/armv7/msm7630/board.c create mode 100644 arch/arm/cpu/armv7/msm7630/config.mk create mode 100644 arch/arm/cpu/armv7/msm7630/gpio.c create mode 100644 arch/arm/cpu/armv7/msm7630/lowlevel_init.S create mode 100644 arch/arm/cpu/armv7/msm7630/timer.c create mode 100644 arch/arm/include/asm/arch-msm7630/adm.h create mode 100644 arch/arm/include/asm/arch-msm7630/gpio.h create mode 100644 arch/arm/include/asm/arch-msm7630/gpio_hw.h create mode 100644 arch/arm/include/asm/arch-msm7630/iomap.h create mode 100644 arch/arm/include/asm/arch-msm7630/mmc.h create mode 100644 arch/arm/include/asm/arch-msm7630/proc_comm.h create mode 100644 arch/arm/include/asm/arch-msm7630/sys_proto.h create mode 100644 board/qcom/msm7630_surf/Makefile create mode 100644 board/qcom/msm7630_surf/msm7630_surf.c create mode 100644 board/qcom/msm7630_surf/msm7630_surf.h create mode 100644 drivers/misc/msm_proc_comm.c create mode 100644 drivers/mmc/qc_mmc.c create mode 100644 drivers/serial/serial_msm_uart.c create mode 100644 include/configs/msm7630_surf.h The contents of this e-mail and any attachment(s) may contain confidential or privileged information for the intended recipient(s). Unintended recipients are prohibited from taking action on the basis of information in this e-mail and using or disseminating the information, and must notify the sender and delete it from their system. L&T Infotech will not accept responsibility or liability for the accuracy or completeness of, or the presence of any virus or disabling code in this e-mail"

3 2

[U-Boot] [PATCH 01/10] dm: arm: Remove support for lpc2292
by Marek Vasut 26 Oct '12

26 Oct '12

This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Wolfgang Denk <wd(a)denx.de> Cc: Albert Aribaud <albert.u.boot(a)aribaud.net> Cc: U-Boot DM <u-boot-dm(a)lists.denx.de> --- arch/arm/cpu/arm720t/cpu.c | 2 +- arch/arm/cpu/arm720t/interrupts.c | 28 +-- arch/arm/cpu/arm720t/lpc2292/Makefile | 50 ---- arch/arm/cpu/arm720t/lpc2292/flash.c | 249 -------------------- arch/arm/cpu/arm720t/lpc2292/iap_entry.S | 7 - arch/arm/cpu/arm720t/lpc2292/mmc.c | 131 ---------- arch/arm/cpu/arm720t/lpc2292/mmc_hw.c | 233 ------------------ arch/arm/cpu/arm720t/lpc2292/mmc_hw.h | 29 --- arch/arm/cpu/arm720t/lpc2292/spi.c | 40 ---- arch/arm/cpu/arm720t/start.S | 70 ------ arch/arm/include/asm/arch-lpc2292/hardware.h | 33 --- .../include/asm/arch-lpc2292/lpc2292_registers.h | 225 ------------------ arch/arm/include/asm/arch-lpc2292/spi.h | 82 ------- drivers/i2c/soft_i2c.c | 3 - drivers/serial/Makefile | 1 - drivers/serial/serial_lpc2292.c | 104 -------- include/flash.h | 1 - 17 files changed, 2 insertions(+), 1286 deletions(-) delete mode 100644 arch/arm/cpu/arm720t/lpc2292/Makefile delete mode 100644 arch/arm/cpu/arm720t/lpc2292/flash.c delete mode 100644 arch/arm/cpu/arm720t/lpc2292/iap_entry.S delete mode 100644 arch/arm/cpu/arm720t/lpc2292/mmc.c delete mode 100644 arch/arm/cpu/arm720t/lpc2292/mmc_hw.c delete mode 100644 arch/arm/cpu/arm720t/lpc2292/mmc_hw.h delete mode 100644 arch/arm/cpu/arm720t/lpc2292/spi.c delete mode 100644 arch/arm/include/asm/arch-lpc2292/hardware.h delete mode 100644 arch/arm/include/asm/arch-lpc2292/lpc2292_registers.h delete mode 100644 arch/arm/include/asm/arch-lpc2292/spi.h delete mode 100644 drivers/serial/serial_lpc2292.c diff --git a/arch/arm/cpu/arm720t/cpu.c b/arch/arm/cpu/arm720t/cpu.c index 974f288..52685c1 100644 --- a/arch/arm/cpu/arm720t/cpu.c +++ b/arch/arm/cpu/arm720t/cpu.c @@ -46,7 +46,7 @@ int cleanup_before_linux (void) * and we set the CPU-speed to 73 MHz - see start.S for details */ -#if defined(CONFIG_NETARM) || defined(CONFIG_S3C4510B) || defined(CONFIG_LPC2292) +#if defined(CONFIG_NETARM) || defined(CONFIG_S3C4510B) disable_interrupts (); /* Nothing more needed */ #elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR) diff --git a/arch/arm/cpu/arm720t/interrupts.c b/arch/arm/cpu/arm720t/interrupts.c index 464dd30..45e3cde 100644 --- a/arch/arm/cpu/arm720t/interrupts.c +++ b/arch/arm/cpu/arm720t/interrupts.c @@ -37,11 +37,6 @@ /* macro to read the 16 bit timer */ #define READ_TIMER (IO_TC1D & 0xffff) -#ifdef CONFIG_LPC2292 -#undef READ_TIMER -#define READ_TIMER (0xFFFFFFFF - GET32(T0TC)) -#endif - #else #define IRQEN (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_INTR_ENABLE)) #define TM2CTRL (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_TIMER2_CONTROL)) @@ -73,13 +68,6 @@ void do_irq (struct pt_regs *pt_regs) } #elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR) /* No do_irq() for IntegratorAP/CM720T as yet */ -#elif defined(CONFIG_LPC2292) - - void (*pfnct)(void); - - pfnct = (void (*)(void))VICVectAddr; - - (*pfnct)(); #else #error do_irq() not defined for this CPU type #endif @@ -172,14 +160,6 @@ int timer_init (void) /* Start timer */ SET_REG( REG_TMOD, TM0_RUN); -#elif defined(CONFIG_LPC2292) - PUT32(T0IR, 0); /* disable all timer0 interrupts */ - PUT32(T0TCR, 0); /* disable timer0 */ - PUT32(T0PR, CONFIG_SYS_SYS_CLK_FREQ / CONFIG_SYS_HZ); - PUT32(T0MCR, 0); - PUT32(T0TC, 0); - PUT32(T0TCR, 1); /* enable timer0 */ - #else #error No timer_init() defined for this CPU type #endif @@ -195,7 +175,7 @@ int timer_init (void) */ -#if defined(CONFIG_NETARM) || defined(CONFIG_LPC2292) +#if defined(CONFIG_NETARM) ulong get_timer (ulong base) { @@ -213,12 +193,6 @@ void __udelay (unsigned long usec) tmo += get_timer (0); while (get_timer_masked () < tmo) -#ifdef CONFIG_LPC2292 - /* GJ - not sure whether this is really needed or a misunderstanding */ - __asm__ __volatile__(" nop"); -#else - /*NOP*/; -#endif } ulong get_timer_masked (void) diff --git a/arch/arm/cpu/arm720t/lpc2292/Makefile b/arch/arm/cpu/arm720t/lpc2292/Makefile deleted file mode 100644 index 1b93008..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/Makefile +++ /dev/null @@ -1,50 +0,0 @@ -# -# (C) Copyright 2000-2007 -# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(SOC).o - -COBJS = flash.o mmc.o mmc_hw.o spi.o -SOBJS = $(obj)iap_entry.o - -SRCS := $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) - -all: $(obj).depend $(LIB) - -$(LIB): $(OBJS) $(SOBJS) - $(call cmd_link_o_target, $(OBJS) $(SOBJS)) - -# this MUST be compiled as thumb code! -$(SOBJS): - $(CC) $(AFLAGS) -march=armv4t -c -o $(SOBJS) iap_entry.S - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/arch/arm/cpu/arm720t/lpc2292/flash.c b/arch/arm/cpu/arm720t/lpc2292/flash.c deleted file mode 100644 index 3d2dc32..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/flash.c +++ /dev/null @@ -1,249 +0,0 @@ -/* - * (C) Copyright 2006 Embedded Artists AB <www.embeddedartists.com> - * - * Modified to remove all but the IAP-command related code by - * Gary Jennejohn <garyj(a)denx.de> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <asm/arch/hardware.h> - -/* IAP commands use 32 bytes at the top of CPU internal sram, we - use 512 bytes below that */ -#define COPY_BUFFER_LOCATION 0x40003de0 - -#define IAP_LOCATION 0x7ffffff1 -#define IAP_CMD_PREPARE 50 -#define IAP_CMD_COPY 51 -#define IAP_CMD_ERASE 52 -#define IAP_CMD_CHECK 53 -#define IAP_CMD_ID 54 -#define IAP_CMD_VERSION 55 -#define IAP_CMD_COMPARE 56 - -#define IAP_RET_CMD_SUCCESS 0 - -static unsigned long command[5]; -static unsigned long result[2]; - -extern void iap_entry(unsigned long * command, unsigned long * result); - -/*----------------------------------------------------------------------- - * - */ -static int get_flash_sector(flash_info_t * info, ulong flash_addr) -{ - int i; - - for(i = 1; i < (info->sector_count); i++) { - if (flash_addr < (info->start[i])) - break; - } - - return (i-1); -} - -/*----------------------------------------------------------------------- - * This function assumes that flash_addr is aligned on 512 bytes boundary - * in flash. This function also assumes that prepare have been called - * for the sector in question. - */ -int lpc2292_copy_buffer_to_flash(flash_info_t * info, ulong flash_addr) -{ - int first_sector; - int last_sector; - - first_sector = get_flash_sector(info, flash_addr); - last_sector = get_flash_sector(info, flash_addr + 512 - 1); - - /* prepare sectors for write */ - command[0] = IAP_CMD_PREPARE; - command[1] = first_sector; - command[2] = last_sector; - iap_entry(command, result); - if (result[0] != IAP_RET_CMD_SUCCESS) { - printf("IAP prepare failed\n"); - return ERR_PROG_ERROR; - } - - command[0] = IAP_CMD_COPY; - command[1] = flash_addr; - command[2] = COPY_BUFFER_LOCATION; - command[3] = 512; - command[4] = CONFIG_SYS_SYS_CLK_FREQ >> 10; - iap_entry(command, result); - if (result[0] != IAP_RET_CMD_SUCCESS) { - printf("IAP copy failed\n"); - return 1; - } - - return 0; -} - -/*----------------------------------------------------------------------- - */ - -int lpc2292_flash_erase (flash_info_t * info, int s_first, int s_last) -{ - int flag; - int prot; - int sect; - - prot = 0; - for (sect = s_first; sect <= s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - if (prot) - return ERR_PROTECTED; - - - flag = disable_interrupts(); - - printf ("Erasing %d sectors starting at sector %2d.\n" - "This make take some time ... ", - s_last - s_first + 1, s_first); - - command[0] = IAP_CMD_PREPARE; - command[1] = s_first; - command[2] = s_last; - iap_entry(command, result); - if (result[0] != IAP_RET_CMD_SUCCESS) { - printf("IAP prepare failed\n"); - return ERR_PROTECTED; - } - - command[0] = IAP_CMD_ERASE; - command[1] = s_first; - command[2] = s_last; - command[3] = CONFIG_SYS_SYS_CLK_FREQ >> 10; - iap_entry(command, result); - if (result[0] != IAP_RET_CMD_SUCCESS) { - printf("IAP erase failed\n"); - return ERR_PROTECTED; - } - - if (flag) - enable_interrupts(); - - return ERR_OK; -} - -int lpc2292_write_buff (flash_info_t * info, uchar * src, ulong addr, - ulong cnt) -{ - int first_copy_size; - int last_copy_size; - int first_block; - int last_block; - int nbr_mid_blocks; - uchar memmap_value; - ulong i; - uchar* src_org; - uchar* dst_org; - int ret = ERR_OK; - - src_org = src; - dst_org = (uchar*)addr; - - first_block = addr / 512; - last_block = (addr + cnt) / 512; - nbr_mid_blocks = last_block - first_block - 1; - - first_copy_size = 512 - (addr % 512); - last_copy_size = (addr + cnt) % 512; - - debug("\ncopy first block: (1) %lX -> %lX 0x200 bytes, " - "(2) %lX -> %lX 0x%X bytes, (3) %lX -> %lX 0x200 bytes\n", - (ulong)(first_block * 512), - (ulong)COPY_BUFFER_LOCATION, - (ulong)src, - (ulong)(COPY_BUFFER_LOCATION + 512 - first_copy_size), - first_copy_size, - (ulong)COPY_BUFFER_LOCATION, - (ulong)(first_block * 512)); - - /* copy first block */ - memcpy((void*)COPY_BUFFER_LOCATION, - (void*)(first_block * 512), 512); - memcpy((void*)(COPY_BUFFER_LOCATION + 512 - first_copy_size), - src, first_copy_size); - lpc2292_copy_buffer_to_flash(info, first_block * 512); - src += first_copy_size; - addr += first_copy_size; - - /* copy middle blocks */ - for (i = 0; i < nbr_mid_blocks; i++) { - debug("copy middle block: %lX -> %lX 512 bytes, " - "%lX -> %lX 512 bytes\n", - (ulong)src, - (ulong)COPY_BUFFER_LOCATION, - (ulong)COPY_BUFFER_LOCATION, - (ulong)addr); - - memcpy((void*)COPY_BUFFER_LOCATION, src, 512); - lpc2292_copy_buffer_to_flash(info, addr); - src += 512; - addr += 512; - } - - - if (last_copy_size > 0) { - debug("copy last block: (1) %lX -> %lX 0x200 bytes, " - "(2) %lX -> %lX 0x%X bytes, (3) %lX -> %lX x200 bytes\n", - (ulong)(last_block * 512), - (ulong)COPY_BUFFER_LOCATION, - (ulong)src, - (ulong)(COPY_BUFFER_LOCATION), - last_copy_size, - (ulong)COPY_BUFFER_LOCATION, - (ulong)addr); - - /* copy last block */ - memcpy((void*)COPY_BUFFER_LOCATION, - (void*)(last_block * 512), 512); - memcpy((void*)COPY_BUFFER_LOCATION, - src, last_copy_size); - lpc2292_copy_buffer_to_flash(info, addr); - } - - /* verify write */ - memmap_value = GET8(MEMMAP); - - disable_interrupts(); - - PUT8(MEMMAP, 01); /* we must make sure that initial 64 - bytes are taken from flash when we - do the compare */ - - for (i = 0; i < cnt; i++) { - if (*dst_org != *src_org){ - printf("Write failed. Byte %lX differs\n", i); - ret = ERR_PROG_ERROR; - break; - } - dst_org++; - src_org++; - } - - PUT8(MEMMAP, memmap_value); - enable_interrupts(); - - return ret; -} diff --git a/arch/arm/cpu/arm720t/lpc2292/iap_entry.S b/arch/arm/cpu/arm720t/lpc2292/iap_entry.S deleted file mode 100644 index c31d519..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/iap_entry.S +++ /dev/null @@ -1,7 +0,0 @@ -IAP_ADDRESS: .word 0x7FFFFFF1 - -.globl iap_entry -iap_entry: - ldr r2, IAP_ADDRESS - bx r2 - mov pc, lr diff --git a/arch/arm/cpu/arm720t/lpc2292/mmc.c b/arch/arm/cpu/arm720t/lpc2292/mmc.c deleted file mode 100644 index beaffe9..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/mmc.c +++ /dev/null @@ -1,131 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <config.h> -#include <common.h> -#include <mmc.h> -#include <asm/errno.h> -#include <asm/arch/hardware.h> -#include <part.h> -#include <fat.h> -#include "mmc_hw.h" -#include <asm/arch/spi.h> - -#ifdef CONFIG_MMC - -#undef MMC_DEBUG - -static block_dev_desc_t mmc_dev; - -/* these are filled out by a call to mmc_hw_get_parameters */ -static int hw_size; /* in kbytes */ -static int hw_nr_sects; -static int hw_sect_size; /* in bytes */ - -block_dev_desc_t * mmc_get_dev(int dev) -{ - return (block_dev_desc_t *)(&mmc_dev); -} - -unsigned long mmc_block_read(int dev, - unsigned long start, - lbaint_t blkcnt, - void *buffer) -{ - unsigned long rc = 0; - unsigned char *p = (unsigned char *)buffer; - unsigned long i; - unsigned long addr = start; - -#ifdef MMC_DEBUG - printf("mmc_block_read: start=%lu, blkcnt=%lu\n", start, - (unsigned long)blkcnt); -#endif - - for(i = 0; i < (unsigned long)blkcnt; i++) { -#ifdef MMC_DEBUG - printf("mmc_read_sector: addr=%lu, buffer=%p\n", addr, p); -#endif - (void)mmc_read_sector(addr, p); - rc++; - addr++; - p += hw_sect_size; - } - - return rc; -} - -/*----------------------------------------------------------------------------- - * Read hardware paramterers (sector size, size, number of sectors) - */ -static int mmc_hw_get_parameters(void) -{ - unsigned char csddata[16]; - unsigned int sizemult; - unsigned int size; - - mmc_read_csd(csddata); - hw_sect_size = 1<<(csddata[5] & 0x0f); - size = ((csddata[6]&0x03)<<10)+(csddata[7]<<2)+(csddata[8]&0xc0); - sizemult = ((csddata[10] & 0x80)>>7)+((csddata[9] & 0x03)<<1); - hw_nr_sects = (size+1)*(1<<(sizemult+2)); - hw_size = hw_nr_sects*hw_sect_size/1024; - -#ifdef MMC_DEBUG - printf("mmc_hw_get_parameters: hw_sect_size=%d, hw_nr_sects=%d, " - "hw_size=%d\n", hw_sect_size, hw_nr_sects, hw_size); -#endif - - return 0; -} - -int mmc_legacy_init(int verbose) -{ - int ret = -ENODEV; - - if (verbose) - printf("mmc_legacy_init\n"); - - spi_init(); - /* this meeds to be done twice */ - mmc_hw_init(); - udelay(1000); - mmc_hw_init(); - - mmc_hw_get_parameters(); - - mmc_dev.if_type = IF_TYPE_MMC; - mmc_dev.part_type = PART_TYPE_DOS; - mmc_dev.dev = 0; - mmc_dev.lun = 0; - mmc_dev.type = 0; - mmc_dev.blksz = hw_sect_size; - mmc_dev.lba = hw_nr_sects; - sprintf((char*)mmc_dev.vendor, "Unknown vendor"); - sprintf((char*)mmc_dev.product, "Unknown product"); - sprintf((char*)mmc_dev.revision, "N/A"); - mmc_dev.removable = 0; /* should be true??? */ - mmc_dev.block_read = mmc_block_read; - - fat_register_device(&mmc_dev, 1); - - ret = 0; - - return ret; -} - -#endif /* CONFIG_MMC */ diff --git a/arch/arm/cpu/arm720t/lpc2292/mmc_hw.c b/arch/arm/cpu/arm720t/lpc2292/mmc_hw.c deleted file mode 100644 index bd6a5b1..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/mmc_hw.c +++ /dev/null @@ -1,233 +0,0 @@ -/* - This code was original written by Ulrich Radig and modified by - Embedded Artists AB (www.embeddedartists.com). - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <config.h> -#include <common.h> -#include <asm/arch/hardware.h> -#include <asm/arch/spi.h> - -#define MMC_Enable() PUT32(IO1CLR, 1l << 22) -#define MMC_Disable() PUT32(IO1SET, 1l << 22) -#define mmc_spi_cfg() spi_set_clock(8); spi_set_cfg(0, 1, 0); - -static unsigned char Write_Command_MMC (unsigned char *CMD); -static void MMC_Read_Block(unsigned char *CMD, unsigned char *Buffer, - unsigned short int Bytes); - -/* initialize the hardware */ -int mmc_hw_init(void) -{ - unsigned long a; - unsigned short int Timeout = 0; - unsigned char b; - unsigned char CMD[] = {0x40, 0x00, 0x00, 0x00, 0x00, 0x95}; - - /* set-up GPIO and SPI */ - (*((volatile unsigned long *)PINSEL2)) &= ~(1l << 3); /* clear bit 3 */ - (*((volatile unsigned long *)IO1DIR)) |= (1l << 22); /* set bit 22 (output) */ - - MMC_Disable(); - - spi_lock(); - spi_set_clock(248); - spi_set_cfg(0, 1, 0); - MMC_Enable(); - - /* waste some time */ - for(a=0; a < 20000; a++) - asm("nop"); - - /* Put the MMC/SD-card into SPI-mode */ - for (b = 0; b < 10; b++) /* Sends min 74+ clocks to the MMC/SD-card */ - spi_write(0xff); - - /* Sends command CMD0 to MMC/SD-card */ - while (Write_Command_MMC(CMD) != 1) { - if (Timeout++ > 200) { - MMC_Disable(); - spi_unlock(); - return(1); /* Abort with command 1 (return 1) */ - } - } - /* Sends Command CMD1 an MMC/SD-card */ - Timeout = 0; - CMD[0] = 0x41;/* Command 1 */ - CMD[5] = 0xFF; - - while (Write_Command_MMC(CMD) != 0) { - if (Timeout++ > 200) { - MMC_Disable(); - spi_unlock(); - return (2); /* Abort with command 2 (return 2) */ - } - } - - MMC_Disable(); - spi_unlock(); - - return 0; -} - -/* ############################################################################ - Sends a command to the MMC/SD-card - ######################################################################### */ -static unsigned char Write_Command_MMC (unsigned char *CMD) -{ - unsigned char a, tmp = 0xff; - unsigned short int Timeout = 0; - - MMC_Disable(); - spi_write(0xFF); - MMC_Enable(); - - for (a = 0; a < 0x06; a++) - spi_write(*CMD++); - - while (tmp == 0xff) { - tmp = spi_read(); - if (Timeout++ > 5000) - break; - } - - return (tmp); -} - -/* ############################################################################ - Routine to read the CID register from the MMC/SD-card (16 bytes) - ######################################################################### */ -void MMC_Read_Block(unsigned char *CMD, unsigned char *Buffer, unsigned short - int Bytes) -{ - unsigned short int a; - - spi_lock(); - mmc_spi_cfg(); - MMC_Enable(); - - if (Write_Command_MMC(CMD) != 0) { - MMC_Disable(); - spi_unlock(); - return; - } - - while (spi_read() != 0xfe) {}; - for (a = 0; a < Bytes; a++) - *Buffer++ = spi_read(); - - /* Read the CRC-byte */ - spi_read(); /* CRC - byte is discarded */ - spi_read(); /* CRC - byte is discarded */ - /* set MMC_Chip_Select to high (MMC/SD-card Inaktiv) */ - MMC_Disable(); - spi_unlock(); - - return; -} - -/* ############################################################################ - Routine to read a block (512 bytes) from the MMC/SD-card - ######################################################################### */ -unsigned char mmc_read_sector (unsigned long addr,unsigned char *Buffer) -{ - /* Command 16 to read aBlocks from the MMC/SD - caed */ - unsigned char CMD[] = {0x51,0x00,0x00,0x00,0x00,0xFF}; - - /* The address on the MMC/SD-card is in bytes, - addr is transformed from blocks to bytes and the result is - placed into the command */ - - addr = addr << 9; /* addr = addr * 512 */ - - CMD[1] = ((addr & 0xFF000000) >> 24); - CMD[2] = ((addr & 0x00FF0000) >> 16); - CMD[3] = ((addr & 0x0000FF00) >> 8 ); - - MMC_Read_Block(CMD, Buffer, 512); - - return (0); -} - -/* ############################################################################ - Routine to write a block (512 byte) to the MMC/SD-card - ######################################################################### */ -unsigned char mmc_write_sector (unsigned long addr,unsigned char *Buffer) -{ - unsigned char tmp, a; - unsigned short int b; - /* Command 24 to write a block to the MMC/SD - card */ - unsigned char CMD[] = {0x58, 0x00, 0x00, 0x00, 0x00, 0xFF}; - - /* The address on the MMC/SD-card is in bytes, - addr is transformed from blocks to bytes and the result is - placed into the command */ - - addr = addr << 9; /* addr = addr * 512 */ - - CMD[1] = ((addr & 0xFF000000) >> 24); - CMD[2] = ((addr & 0x00FF0000) >> 16); - CMD[3] = ((addr & 0x0000FF00) >> 8 ); - - spi_lock(); - mmc_spi_cfg(); - MMC_Enable(); - - /* Send command CMD24 to the MMC/SD-card (Write 1 Block/512 Bytes) */ - tmp = Write_Command_MMC(CMD); - if (tmp != 0) { - MMC_Disable(); - spi_unlock(); - return(tmp); - } - - /* Do a short delay and send a clock-pulse to the MMC/SD-card */ - for (a = 0; a < 100; a++) - spi_read(); - - /* Send a start byte to the MMC/SD-card */ - spi_write(0xFE); - - /* Write the block (512 bytes) to the MMC/SD-card */ - for (b = 0; b < 512; b++) - spi_write(*Buffer++); - - /* write the CRC-Byte */ - spi_write(0xFF); /* write a dummy CRC */ - spi_write(0xFF); /* CRC code is not used */ - - /* Wait for MMC/SD-card busy */ - while (spi_read() != 0xff) {}; - - /* set MMC_Chip_Select to high (MMC/SD-card inactive) */ - MMC_Disable(); - spi_unlock(); - return (0); -} - -/* ######################################################################### - Routine to read the CSD register from the MMC/SD-card (16 bytes) - ######################################################################### */ -unsigned char mmc_read_csd (unsigned char *Buffer) -{ - /* Command to read the CSD register */ - unsigned char CMD[] = {0x49, 0x00, 0x00, 0x00, 0x00, 0xFF}; - - MMC_Read_Block(CMD, Buffer, 16); - - return (0); -} diff --git a/arch/arm/cpu/arm720t/lpc2292/mmc_hw.h b/arch/arm/cpu/arm720t/lpc2292/mmc_hw.h deleted file mode 100644 index 3687dbf..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/mmc_hw.h +++ /dev/null @@ -1,29 +0,0 @@ -/* - This module implements a linux character device driver for the 24c256 chip. - Copyright (C) 2006 Embedded Artists AB (www.embeddedartists.com) - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#ifndef _MMC_HW_ -#define _MMC_HW_ - -unsigned char mmc_read_csd(unsigned char *Buffer); -unsigned char mmc_read_sector (unsigned long addr, - unsigned char *Buffer); -unsigned char mmc_write_sector (unsigned long addr,unsigned char *Buffer); -int mmc_hw_init(void); - -#endif /* _MMC_HW_ */ diff --git a/arch/arm/cpu/arm720t/lpc2292/spi.c b/arch/arm/cpu/arm720t/lpc2292/spi.c deleted file mode 100644 index d296bda..0000000 --- a/arch/arm/cpu/arm720t/lpc2292/spi.c +++ /dev/null @@ -1,40 +0,0 @@ -/* - This module implements an interface to the SPI on the lpc22xx. - Copyright (C) 2006 Embedded Artists AB (www.embeddedartists.com) - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <config.h> -#include <common.h> -#include <asm/errno.h> -#include <asm/arch/hardware.h> -#include <asm/arch/spi.h> - -unsigned long spi_flags; -unsigned char spi_idle = 0x00; - -int spi_init(void) -{ - unsigned long pinsel0_value; - - /* activate spi pins */ - pinsel0_value = GET32(PINSEL0); - pinsel0_value &= ~(0xFFl << 8); - pinsel0_value |= (0x55l << 8); - PUT32(PINSEL0, pinsel0_value); - - return 0; -} diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S index 540e3c2..8ecd351 100644 --- a/arch/arm/cpu/arm720t/start.S +++ b/arch/arm/cpu/arm720t/start.S @@ -43,11 +43,7 @@ _start: b reset ldr pc, _software_interrupt ldr pc, _prefetch_abort ldr pc, _data_abort -#ifdef CONFIG_LPC2292 - .word 0xB4405F76 /* 2's complement of the checksum of the vectors */ -#else ldr pc, _not_used -#endif ldr pc, _irq ldr pc, _fiq @@ -135,10 +131,6 @@ reset: bl cpu_init_crit #endif -#ifdef CONFIG_LPC2292 - bl lowlevel_init -#endif - /* Set stackpointer in internal RAM to call board_init_f */ call_board_init_f: ldr sp, =(CONFIG_SYS_INIT_SP_ADDR) @@ -272,16 +264,6 @@ _dynsym_start_ofs: ************************************************************************* */ -#if defined(CONFIG_LPC2292) -PLLCFG_ADR: .word PLLCFG -PLLFEED_ADR: .word PLLFEED -PLLCON_ADR: .word PLLCON -PLLSTAT_ADR: .word PLLSTAT -VPBDIV_ADR: .word VPBDIV -MEMMAP_ADR: .word MEMMAP - -#endif - cpu_init_crit: #if defined(CONFIG_NETARM) /* @@ -352,50 +334,6 @@ cpu_init_crit: #elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR) /* No specific initialisation for IntegratorAP/CM720T as yet */ -#elif defined(CONFIG_LPC2292) - /* Set-up PLL */ - mov r3, #0xAA - mov r4, #0x55 - /* First disconnect and disable the PLL */ - ldr r0, PLLCON_ADR - mov r1, #0x00 - str r1, [r0] - ldr r0, PLLFEED_ADR /* start feed sequence */ - str r3, [r0] - str r4, [r0] /* feed sequence done */ - /* Set new M and P values */ - ldr r0, PLLCFG_ADR - mov r1, #0x23 /* M=4 and P=2 */ - str r1, [r0] - ldr r0, PLLFEED_ADR /* start feed sequence */ - str r3, [r0] - str r4, [r0] /* feed sequence done */ - /* Then enable the PLL */ - ldr r0, PLLCON_ADR - mov r1, #0x01 /* PLL enable bit */ - str r1, [r0] - ldr r0, PLLFEED_ADR /* start feed sequence */ - str r3, [r0] - str r4, [r0] /* feed sequence done */ - /* Wait for the lock */ - ldr r0, PLLSTAT_ADR - mov r1, #0x400 /* lock bit */ -lock_loop: - ldr r2, [r0] - and r2, r1, r2 - cmp r2, #0 - beq lock_loop - /* And finally connect the PLL */ - ldr r0, PLLCON_ADR - mov r1, #0x03 /* PLL enable bit and connect bit */ - str r1, [r0] - ldr r0, PLLFEED_ADR /* start feed sequence */ - str r3, [r0] - str r4, [r0] /* feed sequence done */ - /* Set-up VPBDIV register */ - ldr r0, VPBDIV_ADR - mov r1, #0x01 /* VPB clock is same as process clock */ - str r1, [r0] #else #error No cpu_init_crit() defined for current CPU type #endif @@ -411,7 +349,6 @@ lock_loop: str r1, [r0] #endif -#ifndef CONFIG_LPC2292 mov ip, lr /* * before relocating, we have to setup RAM timing @@ -420,8 +357,6 @@ lock_loop: */ bl lowlevel_init mov lr, ip -#endif - mov pc, lr @@ -613,11 +548,6 @@ reset_cpu: * on external peripherals such as watchdog timers, etc. */ #elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR) /* No specific reset actions for IntegratorAP/CM720T as yet */ -#elif defined(CONFIG_LPC2292) - .align 5 -.globl reset_cpu -reset_cpu: - mov pc, r0 #else #error No reset_cpu() defined for current CPU type #endif diff --git a/arch/arm/include/asm/arch-lpc2292/hardware.h b/arch/arm/include/asm/arch-lpc2292/hardware.h deleted file mode 100644 index 5e227e3..0000000 --- a/arch/arm/include/asm/arch-lpc2292/hardware.h +++ /dev/null @@ -1,33 +0,0 @@ -#ifndef __ASM_ARCH_HARDWARE_H -#define __ASM_ARCH_HARDWARE_H - -/* - * Copyright (c) 2004 Cucy Systems (http://www.cucy.com) - * Curt Brune <curt(a)cucy.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#if defined(CONFIG_LPC2292) -#include <asm/arch-lpc2292/lpc2292_registers.h> -#else -#error No hardware file defined for this configuration -#endif - -#endif /* __ASM_ARCH_HARDWARE_H */ diff --git a/arch/arm/include/asm/arch-lpc2292/lpc2292_registers.h b/arch/arm/include/asm/arch-lpc2292/lpc2292_registers.h deleted file mode 100644 index 5715f3e..0000000 --- a/arch/arm/include/asm/arch-lpc2292/lpc2292_registers.h +++ /dev/null @@ -1,225 +0,0 @@ -#ifndef __LPC2292_REGISTERS_H -#define __LPC2292_REGISTERS_H - -#include <config.h> - -/* Macros for reading/writing registers */ -#define PUT8(reg, value) (*(volatile unsigned char*)(reg) = (value)) -#define PUT16(reg, value) (*(volatile unsigned short*)(reg) = (value)) -#define PUT32(reg, value) (*(volatile unsigned int*)(reg) = (value)) -#define GET8(reg) (*(volatile unsigned char*)(reg)) -#define GET16(reg) (*(volatile unsigned short*)(reg)) -#define GET32(reg) (*(volatile unsigned int*)(reg)) - -/* External Memory Controller */ - -#define BCFG0 0xFFE00000 /* 32-bits */ -#define BCFG1 0xFFE00004 /* 32-bits */ -#define BCFG2 0xFFE00008 /* 32-bits */ -#define BCFG3 0xFFE0000c /* 32-bits */ - -/* System Control Block */ - -#define EXTINT 0xE01FC140 -#define EXTWAKE 0xE01FC144 -#define EXTMODE 0xE01FC148 -#define EXTPOLAR 0xE01FC14C -#define MEMMAP 0xE01FC040 -#define PLLCON 0xE01FC080 -#define PLLCFG 0xE01FC084 -#define PLLSTAT 0xE01FC088 -#define PLLFEED 0xE01FC08C -#define PCON 0xE01FC0C0 -#define PCONP 0xE01FC0C4 -#define VPBDIV 0xE01FC100 - -/* Memory Acceleration Module */ - -#define MAMCR 0xE01FC000 -#define MAMTIM 0xE01FC004 - -/* Vectored Interrupt Controller */ - -#define VICIRQStatus 0xFFFFF000 -#define VICFIQStatus 0xFFFFF004 -#define VICRawIntr 0xFFFFF008 -#define VICIntSelect 0xFFFFF00C -#define VICIntEnable 0xFFFFF010 -#define VICIntEnClr 0xFFFFF014 -#define VICSoftInt 0xFFFFF018 -#define VICSoftIntClear 0xFFFFF01C -#define VICProtection 0xFFFFF020 -#define VICVectAddr 0xFFFFF030 -#define VICDefVectAddr 0xFFFFF034 -#define VICVectAddr0 0xFFFFF100 -#define VICVectAddr1 0xFFFFF104 -#define VICVectAddr2 0xFFFFF108 -#define VICVectAddr3 0xFFFFF10C -#define VICVectAddr4 0xFFFFF110 -#define VICVectAddr5 0xFFFFF114 -#define VICVectAddr6 0xFFFFF118 -#define VICVectAddr7 0xFFFFF11C -#define VICVectAddr8 0xFFFFF120 -#define VICVectAddr9 0xFFFFF124 -#define VICVectAddr10 0xFFFFF128 -#define VICVectAddr11 0xFFFFF12C -#define VICVectAddr12 0xFFFFF130 -#define VICVectAddr13 0xFFFFF134 -#define VICVectAddr14 0xFFFFF138 -#define VICVectAddr15 0xFFFFF13C -#define VICVectCntl0 0xFFFFF200 -#define VICVectCntl1 0xFFFFF204 -#define VICVectCntl2 0xFFFFF208 -#define VICVectCntl3 0xFFFFF20C -#define VICVectCntl4 0xFFFFF210 -#define VICVectCntl5 0xFFFFF214 -#define VICVectCntl6 0xFFFFF218 -#define VICVectCntl7 0xFFFFF21C -#define VICVectCntl8 0xFFFFF220 -#define VICVectCntl9 0xFFFFF224 -#define VICVectCntl10 0xFFFFF228 -#define VICVectCntl11 0xFFFFF22C -#define VICVectCntl12 0xFFFFF230 -#define VICVectCntl13 0xFFFFF234 -#define VICVectCntl14 0xFFFFF238 -#define VICVectCntl15 0xFFFFF23C - -/* Pin connect block */ - -#define PINSEL0 0xE002C000 /* 32 bits */ -#define PINSEL1 0xE002C004 /* 32 bits */ -#define PINSEL2 0xE002C014 /* 32 bits */ - -/* GPIO */ - -#define IO0PIN 0xE0028000 -#define IO0SET 0xE0028004 -#define IO0DIR 0xE0028008 -#define IO0CLR 0xE002800C -#define IO1PIN 0xE0028010 -#define IO1SET 0xE0028014 -#define IO1DIR 0xE0028018 -#define IO1CLR 0xE002801C -#define IO2PIN 0xE0028020 -#define IO2SET 0xE0028024 -#define IO2DIR 0xE0028028 -#define IO2CLR 0xE002802C -#define IO3PIN 0xE0028030 -#define IO3SET 0xE0028034 -#define IO3DIR 0xE0028038 -#define IO3CLR 0xE002803C - -/* Uarts */ - -#define U0RBR 0xE000C000 -#define U0THR 0xE000C000 -#define U0IER 0xE000C004 -#define U0IIR 0xE000C008 -#define U0FCR 0xE000C008 -#define U0LCR 0xE000C00C -#define U0LSR 0xE000C014 -#define U0SCR 0xE000C01C -#define U0DLL 0xE000C000 -#define U0DLM 0xE000C004 - -#define U1RBR 0xE0010000 -#define U1THR 0xE0010000 -#define U1IER 0xE0010004 -#define U1IIR 0xE0010008 -#define U1FCR 0xE0010008 -#define U1LCR 0xE001000C -#define U1MCR 0xE0010010 -#define U1LSR 0xE0010014 -#define U1MSR 0xE0010018 -#define U1SCR 0xE001001C -#define U1DLL 0xE0010000 -#define U1DLM 0xE0010004 - -/* I2C */ - -#define I2CONSET 0xE001C000 -#define I2STAT 0xE001C004 -#define I2DAT 0xE001C008 -#define I2ADR 0xE001C00C -#define I2SCLH 0xE001C010 -#define I2SCLL 0xE001C014 -#define I2CONCLR 0xE001C018 - -/* SPI */ - -#define S0SPCR 0xE0020000 -#define S0SPSR 0xE0020004 -#define S0SPDR 0xE0020008 -#define S0SPCCR 0xE002000C -#define S0SPINT 0xE002001C - -#define S1SPCR 0xE0030000 -#define S1SPSR 0xE0030004 -#define S1SPDR 0xE0030008 -#define S1SPCCR 0xE003000C -#define S1SPINT 0xE003001C - -/* CAN controller */ - -/* skip for now */ - -/* Timers */ - -#define T0IR 0xE0004000 -#define T0TCR 0xE0004004 -#define T0TC 0xE0004008 -#define T0PR 0xE000400C -#define T0PC 0xE0004010 -#define T0MCR 0xE0004014 -#define T0MR0 0xE0004018 -#define T0MR1 0xE000401C -#define T0MR2 0xE0004020 -#define T0MR3 0xE0004024 -#define T0CCR 0xE0004028 -#define T0CR0 0xE000402C -#define T0CR1 0xE0004030 -#define T0CR2 0xE0004034 -#define T0CR3 0xE0004038 -#define T0EMR 0xE000403C - -#define T1IR 0xE0008000 -#define T1TCR 0xE0008004 -#define T1TC 0xE0008008 -#define T1PR 0xE000800C -#define T1PC 0xE0008010 -#define T1MCR 0xE0008014 -#define T1MR0 0xE0008018 -#define T1MR1 0xE000801C -#define T1MR2 0xE0008020 -#define T1MR3 0xE0008024 -#define T1CCR 0xE0008028 -#define T1CR0 0xE000802C -#define T1CR1 0xE0008030 -#define T1CR2 0xE0008034 -#define T1CR3 0xE0008038 -#define T1EMR 0xE000803C - -/* PWM */ - -/* skip for now */ - -/* A/D converter */ - -/* skip for now */ - -/* Real Time Clock */ - -/* skip for now */ - -/* Watchdog */ - -#define WDMOD 0xE0000000 -#define WDTC 0xE0000004 -#define WDFEED 0xE0000008 -#define WDTV 0xE000000C - -/* EmbeddedICE LOGIC */ - -/* skip for now */ - -#endif diff --git a/arch/arm/include/asm/arch-lpc2292/spi.h b/arch/arm/include/asm/arch-lpc2292/spi.h deleted file mode 100644 index 6ae66e8..0000000 --- a/arch/arm/include/asm/arch-lpc2292/spi.h +++ /dev/null @@ -1,82 +0,0 @@ -/* - This file defines the interface to the lpc22xx SPI module. - Copyright (C) 2006 Embedded Artists AB (www.embeddedartists.com) - - This file may be included in software not adhering to the GPL. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#ifndef SPI_H -#define SPI_H - -#include <config.h> -#include <common.h> -#include <asm/errno.h> -#include <asm/arch/hardware.h> - -#define SPIF 0x80 - -#define spi_lock() disable_interrupts(); -#define spi_unlock() enable_interrupts(); - -extern unsigned long spi_flags; -extern unsigned char spi_idle; - -int spi_init(void); - -static inline unsigned char spi_read(void) -{ - unsigned char b; - - PUT8(S0SPDR, spi_idle); - while (!(GET8(S0SPSR) & SPIF)); - b = GET8(S0SPDR); - - return b; -} - -static inline void spi_write(unsigned char b) -{ - PUT8(S0SPDR, b); - while (!(GET8(S0SPSR) & SPIF)); - GET8(S0SPDR); /* this will clear the SPIF bit */ -} - -static inline void spi_set_clock(unsigned char clk_value) -{ - PUT8(S0SPCCR, clk_value); -} - -static inline void spi_set_cfg(unsigned char phase, - unsigned char polarity, - unsigned char lsbf) -{ - unsigned char v = 0x20; /* master bit set */ - - if (phase) - v |= 0x08; /* set phase bit */ - if (polarity) { - v |= 0x10; /* set polarity bit */ - spi_idle = 0xFF; - } else { - spi_idle = 0x00; - } - if (lsbf) - v |= 0x40; /* set lsbf bit */ - - PUT8(S0SPCR, v); -} -#endif /* SPI_H */ diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c index 36c6114..1595c07 100644 --- a/drivers/i2c/soft_i2c.c +++ b/drivers/i2c/soft_i2c.c @@ -41,9 +41,6 @@ #ifdef CONFIG_IXP425 /* only valid for IXP425 */ #include <asm/arch/ixp425.h> #endif -#ifdef CONFIG_LPC2292 -#include <asm/arch/hardware.h> -#endif #if defined(CONFIG_MPC852T) || defined(CONFIG_MPC866) #include <asm/io.h> #endif diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 65d0f23..cae15f9 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -42,7 +42,6 @@ COBJS-$(CONFIG_CLPS7111_SERIAL) += serial_clps7111.o COBJS-$(CONFIG_IMX_SERIAL) += serial_imx.o COBJS-$(CONFIG_IXP_SERIAL) += serial_ixp.o COBJS-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o -COBJS-$(CONFIG_LPC2292_SERIAL) += serial_lpc2292.o COBJS-$(CONFIG_LH7A40X_SERIAL) += serial_lh7a40x.o COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o COBJS-$(CONFIG_MXC_UART) += serial_mxc.o diff --git a/drivers/serial/serial_lpc2292.c b/drivers/serial/serial_lpc2292.c deleted file mode 100644 index e3a60b6..0000000 --- a/drivers/serial/serial_lpc2292.c +++ /dev/null @@ -1,104 +0,0 @@ -/* - * (C) Copyright 2002-2004 - * Wolfgang Denk, DENX Software Engineering, <wd(a)denx.de> - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger(a)sysgo.de> - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Alex Zuepke <azu(a)sysgo.de> - * - * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw(a)its.tudelft.nl) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#include <common.h> -#include <asm/arch/hardware.h> - -DECLARE_GLOBAL_DATA_PTR; - -void serial_setbrg (void) -{ - unsigned short divisor = 0; - - switch (gd->baudrate) { - case 1200: divisor = 3072; break; - case 9600: divisor = 384; break; - case 19200: divisor = 192; break; - case 38400: divisor = 96; break; - case 57600: divisor = 64; break; - case 115200: divisor = 32; break; - default: hang (); break; - } - - /* init serial UART0 */ - PUT8(U0LCR, 0); - PUT8(U0IER, 0); - PUT8(U0LCR, 0x80); /* DLAB=1 */ - PUT8(U0DLL, (unsigned char)(divisor & 0x00FF)); - PUT8(U0DLM, (unsigned char)(divisor >> 8)); - PUT8(U0LCR, 0x03); /* 8N1, DLAB=0 */ - PUT8(U0FCR, 1); /* Enable RX and TX FIFOs */ -} - -int serial_init (void) -{ - unsigned long pinsel0; - - serial_setbrg (); - - pinsel0 = GET32(PINSEL0); - pinsel0 &= ~(0x00000003); - pinsel0 |= 5; - PUT32(PINSEL0, pinsel0); - - return (0); -} - -void serial_putc (const char c) -{ - if (c == '\n') - { - while((GET8(U0LSR) & (1<<5)) == 0); /* Wait for empty U0THR */ - PUT8(U0THR, '\r'); - } - - while((GET8(U0LSR) & (1<<5)) == 0); /* Wait for empty U0THR */ - PUT8(U0THR, c); -} - -int serial_getc (void) -{ - while((GET8(U0LSR) & 1) == 0); - return GET8(U0RBR); -} - -void -serial_puts (const char *s) -{ - while (*s) { - serial_putc (*s++); - } -} - -/* Test if there is a byte to read */ -int serial_tstc (void) -{ - return (GET8(U0LSR) & 1); -} diff --git a/include/flash.h b/include/flash.h index 0ca70d9..e91a5bf 100644 --- a/include/flash.h +++ b/include/flash.h @@ -347,7 +347,6 @@ extern flash_info_t *flash_get_info(ulong base); #define TOSH_ID_FVT160 0xC2 /* TC58FVT160 ID (16 M, top ) */ #define TOSH_ID_FVB160 0x43 /* TC58FVT160 ID (16 M, bottom ) */ -#define PHILIPS_LPC2292 0x0401FF13 /* LPC2292 internal FLASH */ /*----------------------------------------------------------------------- * Internal FLASH identification codes -- 1.7.10.4

10 35

[U-Boot] [PATCH] nds32: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
by Nobuhiro Iwamatsu 25 Oct '12

25 Oct '12

With almost all the architecture and board BOARD_LATE_INIT does not use. CONFIG_BOARD_LATE_INIT is used instead. This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj(a)renesas.com> CC: Macpaul Lin <macpaul(a)andestech.com> --- arch/nds32/lib/board.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/nds32/lib/board.c b/arch/nds32/lib/board.c index 074aabf..a043b43 100644 --- a/arch/nds32/lib/board.c +++ b/arch/nds32/lib/board.c @@ -408,7 +408,7 @@ void board_init_r(gd_t *id, ulong dest_addr) copy_filename(BootFile, s, sizeof(BootFile)); #endif -#ifdef BOARD_LATE_INIT +#ifdef CONFIG_BOARD_LATE_INIT board_late_init(); #endif -- 1.7.9.5

3 2

[U-Boot] [PATCH] Add support for eco5-pk ARM board
by Raphael Assenat 22 Oct '12

22 Oct '12

This patch adds support for the 8D Technologies ECO5-PK board which is based on the TI AM3505 ARM SOC. Signed-off-by: Raphael Assenat <raph(a)8d.com> diff --git a/board/8dtech/eco5pk/Makefile b/board/8dtech/eco5pk/Makefile new file mode 100644 index 0000000..befe60a --- /dev/null +++ b/board/8dtech/eco5pk/Makefile @@ -0,0 +1,43 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# Adapted from ti/evm/Makefile +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := eco5pk.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend diff --git a/board/8dtech/eco5pk/eco5pk.c b/board/8dtech/eco5pk/eco5pk.c new file mode 100644 index 0000000..ddc5274 --- /dev/null +++ b/board/8dtech/eco5pk/eco5pk.c @@ -0,0 +1,61 @@ +/* + * eco5pk.c - board file for 8D Technology's AM3517 based eco5pk board + * + * Based on am3517evm.c + * + * Copyright (C) 2011-2012 8D Technologies inc. + * Copyright (C) 2009 Texas Instruments Incorporated + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <common.h> +#include <netdev.h> +#include <asm/io.h> +#include <asm/arch/mem.h> +#include <asm/arch/mux.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/emac_defs.h> +#include <asm/gpio.h> +#include <i2c.h> +#include <crc.h> +#include <asm/mach-types.h> +#include "eco5pk.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Routine: board_init + * Description: Early hardware init. + */ +int board_init(void) +{ + gpmc_init(); /* in SRAM or SDRAM, finish GPMC */ + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); + + gpio_request(30, "RESOUT"); + gpio_direction_output(30,1); + return 0; +} + +/* + * Routine: set_muxconf_regs + * Description: Setting up the configuration Mux registers specific to the + * hardware. Many pins need to be moved from protect to primary + * mode. + */ +void set_muxconf_regs(void) +{ + MUX_ECO5_PK(); +} diff --git a/board/8dtech/eco5pk/eco5pk.h b/board/8dtech/eco5pk/eco5pk.h new file mode 100644 index 0000000..0e60ef8 --- /dev/null +++ b/board/8dtech/eco5pk/eco5pk.h @@ -0,0 +1,402 @@ +/* + * eco5.h - Header file for the 8D Technologies ECO5 board. + * + * Based on am3517evm.h + * Based on ti/evm/evm.h + * + * Copyright (C) 2011 8D Technologies inc. + * Copyright (C) 2009 Texas Instruments Incorporated + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef _ECO5PK_H__ +#define _ECO5PK_H__ + +const omap3_sysinfo sysinfo = { + DDR_DISCRETE, + "ECO5 Board", + "NAND", +}; + +/* + * IEN - Input Enable + * IDIS - Input Disable + * PTD - Pull type Down + * PTU - Pull type Up + * DIS - Pull type selection is inactive + * EN - Pull type selection is active + * M0 - Mode 0 + * The commented string gives the final mux configuration for that pin + */ +#define MUX_ECO5_PK() \ + /* SDRC */\ + MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SDRC_DQS0N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_DQS1N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_DQS2N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_DQS3N), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SDRC_CKE0), (M0)) \ + MUX_VAL(CP(SDRC_CKE1), (M0)) \ + MUX_VAL(CP(STRBEN_DLY0), (IEN | PTD | EN | M0)) /*sdrc_strben_dly0*/\ + MUX_VAL(CP(STRBEN_DLY1), (IEN | PTD | EN | M0)) /*sdrc_strben_dly1*/\ + /* GPMC */\ + MUX_VAL(CP(GPMC_A1), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A2), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A3), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A4), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A5), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A6), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A7), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A8), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A9), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_A10), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D0), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D1), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D2), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D3), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D4), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D5), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D6), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D7), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D8), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D9), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D10), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D11), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D12), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D13), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D14), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_D15), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NCS5), (IDIS | PTU | DIS | M3)) /* GPT10_PWM_OUT */ \ + MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | DIS | M4)) \ + MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NBE1), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4)) /*GPIO_64*/\ + /* - ETH_nRESET*/\ + MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) \ + /* DSS */\ + MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA0), (IEN | PTD | DIS | M4)) /* LCD_D0 */ \ + MUX_VAL(CP(DSS_DATA1), (IEN | PTD | DIS | M4)) /* LCD_D1 */ \ + MUX_VAL(CP(DSS_DATA2), (IEN | PTD | DIS | M4)) /* LCD_D2 */ \ + MUX_VAL(CP(DSS_DATA3), (IEN | PTD | DIS | M4)) /* LCD_D3 */ \ + MUX_VAL(CP(DSS_DATA4), (IEN | PTD | DIS | M4)) /* LCD_D4 */ \ + MUX_VAL(CP(DSS_DATA5), (IEN | PTD | DIS | M4)) /* LCD_D5 */ \ + MUX_VAL(CP(DSS_DATA6), (IEN | PTD | DIS | M4)) /* LCD_D6 */ \ + MUX_VAL(CP(DSS_DATA7), (IEN | PTD | DIS | M4)) /* LCD_D7 */ \ + MUX_VAL(CP(DSS_DATA8), (IDIS | PTU | EN | M4)) /* LCD_NWR */ \ + MUX_VAL(CP(DSS_DATA9), (IDIS | PTU | EN | M4)) /* LCD_NRD */ \ + MUX_VAL(CP(DSS_DATA10), (IDIS | PTU | EN | M4)) /* LCD_NCE */ \ + MUX_VAL(CP(DSS_DATA11), (IDIS | PTU | EN | M4)) /* LCD_CD */ \ + MUX_VAL(CP(DSS_DATA12), (IDIS | PTU | EN | M4)) /* LCD_NRST */ \ + MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | EN | M4)) /* LCD_FS */ \ + MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | EN | M4)) /* LCD_RV */ \ + MUX_VAL(CP(DSS_DATA15), (IDIS | PTU | EN | M4)) /* LCD_DIR */ \ + MUX_VAL(CP(DSS_DATA16), (IDIS | PTU | EN | M4)) /* LCD_NOE */ \ + MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | EN | M4)) /* LCD_PWR_EN */ \ + MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) \ + /* CAMERA */\ + MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\ + /* - CAM_RESET*/\ + MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\ + MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) \ + /* MMC */\ + MUX_VAL(CP(MMC1_CLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(MMC1_CMD), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M4)) /* WriteProtect */\ + MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M4)) /* CardDetect*/\ + MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M4)) \ + MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M4)) \ + \ + MUX_VAL(CP(MMC2_CLK), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(MMC2_CMD), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MMC2_DAT3), (IEN | PTD | DIS | M0)) \ + /* McBSP */\ + MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M4)) /* LED ACT */ \ + \ + MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(MCBSP4_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_152*/\ + /* - LCD_INI*/\ + MUX_VAL(CP(MCBSP4_DR), (IDIS | PTD | DIS | M4)) /*GPIO_153*/\ + /* - LCD_ENVDD */\ + MUX_VAL(CP(MCBSP4_DX), (IDIS | PTD | DIS | M4)) /*GPIO_154*/\ + /* - LCD_QVGA/nVGA */\ + MUX_VAL(CP(MCBSP4_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_155*/\ + /* - LCD_RESB */\ + /* UART */\ + MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0)) \ + \ + MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0)) \ + \ + MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTU | DIS | M0)) \ + MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0)) \ + /* I2C */\ + MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) \ + /* McSPI */\ + MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(MCSPI1_CS1), (IEN | PTD | EN | M4)) /*GPIO_175*/\ + MUX_VAL(CP(MCSPI1_CS2), (IEN | PTU | DIS | M4)) /*GPIO_176*/\ + /* - LAN_INTR*/\ + MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0)) \ + \ + MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M4)) \ + MUX_VAL(CP(MCSPI2_CS1), (IDIS | PTD | EN | M4)) /* LCD_EN_BACKLIGHT */ \ + /* CCDC */\ + MUX_VAL(CP(CCDC_PCLK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_FIELD), (IEN | PTD | DIS | M1)) \ + MUX_VAL(CP(CCDC_HD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_VD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(CCDC_WEN), (IEN | PTD | DIS | M1)) \ + MUX_VAL(CP(CCDC_DATA0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(CCDC_DATA7), (IEN | PTD | DIS | M0)) \ + /* RMII */\ + MUX_VAL(CP(RMII_MDIO_DATA), (IEN | M0)) \ + MUX_VAL(CP(RMII_MDIO_CLK), (M0)) \ + MUX_VAL(CP(RMII_RXD0) , (IEN | PTD | M0)) \ + MUX_VAL(CP(RMII_RXD1), (IEN | PTD | M0)) \ + MUX_VAL(CP(RMII_CRS_DV), (IEN | PTD | M0)) \ + MUX_VAL(CP(RMII_RXER), (PTD | M0)) \ + MUX_VAL(CP(RMII_TXD0), (PTD | M0)) \ + MUX_VAL(CP(RMII_TXD1), (PTD | M0)) \ + MUX_VAL(CP(RMII_TXEN), (PTD | M0)) \ + MUX_VAL(CP(RMII_50MHZ_CLK), (IEN | PTD | EN | M0)) \ + /* HECC */\ + MUX_VAL(CP(HECC1_TXD), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(HECC1_RXD), (IEN | PTU | EN | M0)) \ + /* HSUSB */\ + MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(USB0_DRVBUS), (IEN | PTD | EN | M0)) \ + /* HDQ */\ + MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0)) \ + /* Control and debug */\ + MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(SYS_NRESWARM), (IDIS | PTU | DIS | M4)) /*SYS_nRESWARM */\ + /* - GPIO30 */\ + MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\ + /* - PEN_IRQ */\ + MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3 */\ + MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4*/\ + MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\ + MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\ + MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\ + MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/\ + /* - VIO_1V8*/\ + MUX_VAL(CP(SYS_BOOT7), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(SYS_BOOT8), (IEN | PTD | EN | M0)) \ + \ + MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M0)) \ + /* JTAG */\ + MUX_VAL(CP(JTAG_nTRST), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0)) \ + /* ETK (ES2 onwards) */\ + MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M0)) \ + MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D0_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D1_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D2_ES2 ), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(ETK_D3_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D4_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D5_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D6_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D7_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D8_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D9_ES2 ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0)) \ + /* Die to Die */\ + MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0)) \ + MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0)) \ + MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0)) \ + MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0)) \ + +#endif diff --git a/boards.cfg b/boards.cfg index 2d36d83..96233b7 100644 --- a/boards.cfg +++ b/boards.cfg @@ -219,6 +219,7 @@ ima3-mx53 arm armv7 ima3-mx53 esg vision2 arm armv7 vision2 ttcontrol mx5 vision2:IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg mx6qarm2 arm armv7 mx6qarm2 freescale mx6 mx6qarm2:IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/mx6qsabrelite/imximage.cfg +eco5pk arm armv7 eco5pk 8dtech omap3 cm_t35 arm armv7 cm_t35 - omap3 omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3 diff --git a/include/configs/eco5pk.h b/include/configs/eco5pk.h new file mode 100644 index 0000000..7d2ff9e --- /dev/null +++ b/include/configs/eco5pk.h @@ -0,0 +1,73 @@ +/* + * Copyright (C) 2012 8D Technologies inc. + * Based on mt_ventoux.h, original banner below: + * + * Copyright (C) 2011 + * Stefano Babic, DENX Software Engineering, sbabic(a)denx.de. + * + * Copyright (C) 2009 TechNexion Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include "tam3517-common.h" + +#undef CONFIG_USB_EHCI +#undef CONFIG_USB_EHCI_OMAP +#undef CONFIG_USB_OMAP3 +#undef CONFIG_CMD_USB + +/* Our console port is port3 */ +#undef CONFIG_CONS_INDEX +#undef CONFIG_SYS_NS16550_COM1 +#undef CONFIG_SERIAL1 + +#define CONFIG_CONS_INDEX 3 +#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 +#define CONFIG_SERIAL3 + + +#define MACH_TYPE_ECO5_PK 4017 +#define CONFIG_MACH_TYPE MACH_TYPE_ECO5_PK + +#define CONFIG_BOOTDELAY 10 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_AUTO_COMPLETE + +/* + * Miscellaneous configurable options + */ +#define V_PROMPT "ECO5-PK # " +#define CONFIG_SYS_PROMPT V_PROMPT + +/* + * Set its own mtdparts, different from common + */ +#undef MTDIDS_DEFAULT +#undef MTDPARTS_DEFAULT +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(xloader-nand),1024k(uboot-nand),256k(params-nand),256k(logo),5120k(kernel),-(ubifs)" + + +#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_TAM3517_SETTINGS \ + "install_kernel=if dhcp $bootfile; then nand erase kernel; nand write $fileaddr kernel; fi\0" \ + "mtdparts="MTDPARTS_DEFAULT"\0" \ + "serverip=192.168.142.60\0" + + +#endif /* __CONFIG_H */

4 9

[U-Boot] fw_printenv is not working
by mateer 22 Oct '12

22 Oct '12

Hi, when i run fw_printenv , its not working..It shows:- fw_printenv: line 1: syntax error: "(" unexpected error... Let me tell you what i did... 1) i copy the u-boot source code from my colleague and copy in my hard disk. 2) After then i set the environment through commnads. the commands which i run are # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm distclean # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm omap3_evm_config # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm 3) After then i go to /tools/env, where i configure the fw_env.config and then run make command. 4) After ruuning the command i got crc32.c and fw_printenv. 5)i copied the fw_printenv into the SD-Card and insert the card into the OMAP3EVM board. 6) after then when i use the command ./fw_printenv it throws the error fw_printenv: line 1: syntax error: "(" unexpected error.. Can u please help me what i have to do... I think i am doing something wrong... -- View this message in context: http://old.nabble.com/fw_printenv-is-not-working-tp29297562p29297562.html Sent from the Uboot - Users mailing list archive at Nabble.com.

4 3

[U-Boot] [PATCH v3 0/18] tegra: Add display driver and LCD support for Seaboard
by Simon Glass 20 Oct '12

20 Oct '12

This series adds support for the Tegra2x's display peripheral. This supports the LCD display on Seaboard and we use this to enable console output in U-Boot on the LCD. Configuration is via the device tree. Proposed bindings are included in this series, taken from pwm bindings that should be in linux-next, a Tegra video binding that might be accepted in devicetree-discuss and a proposed video mode binding posted to dri-devel. While I agree EDID is convenient for machines I would prefer to provide a user-friendly way of selecting LCD settings as well, with EDID more as a fallback and auto-detection when available. To improve performance two optimisations are offered: 1. The LCD frame buffer is cached, with the cache being flushed after each newline sent to putc(), and in a few other situations. This dramatically increases performance (around 10x). This requires a few additions to the ARM cache support. 2. The console supports scrolling in steps of more than 1 line. This speeds up scrolling output considerably, particularly commands like 'printenv' which display a lot of output, and particular when the dcache is off. This requires a new CONFIG and a change to the console_scrollup() function. Changes in v2: - Add new patch to use const in pinmux_config_pingroup/table() - Add nvidia prefix to device tree properties - Align tegra display using new CONFIG_LCD_ALIGNMENT feature - Put the LCD cache flush logic into lcd_putc() instead of lcd_puts() - Update LCD driver to deal with new fdt bindings - Update seaboard LCD definitions for new fdt binding - Use a more generic config CONFIG_LCD_ALIGNMENT for lcd alignment - Use const where possible in funcmux Changes in v3: - Add new commit for pwm binding and node - Add new panel binding to fit with tegra display controller binding - Add probe function to read in fdt parameters in display driver - Add separate call to pwm_init() in board_init() - Adjust LCD driver to use new SOC display driver structures - Bring in proposed tegra display controller binding - Decode fdt node within the pwm driver - Fix tiny bug in mult-line lcd scrolling - Handle a cached frame buffer out of normal U-Boot memory - Introduce concept of a pwm channel, rather than separate peripherals - Move some fdt decode code from LCD driver to SOC display driver - Put the LCD cache flush logic back into lcd_puts() - Remove LPW1 pin which is not needed by display - Remove spurious newline from fdtdec_get_addr() debug output - Rename fdt config structures - Rename pwfm driver to pwm - Separate display driver and LCD driver more in fdt - Tidy up fdtdec_decode_gpios() debug output - Use displaymode binding for fdt - Use new proposed upstream pwm binding - Use new pwm binding from pre-linux-next - Use new upstream proposed LCD definitions Mayuresh Kulkarni (1): tegra: Enable display/lcd support on Seaboard Simon Glass (16): fdt: Tidy debugging, add to fdtdec_get_int/addr() fdt: Add header guard to fdtdec.h tegra: Use const for pinmux_config_pingroup/table() tegra: Add display support to funcmux tegra: fdt: Add pwm binding and node tegra: fdt: Add LCD definitions for Tegra tegra: Add support for PWM tegra: Add LCD driver tegra: Add LCD support to Nvidia boards arm: Add control over cachability of memory regions lcd: Add CONFIG_LCD_ALIGNMENT to select frame buffer alignment lcd: Add support for flushing LCD fb from dcache after update tegra: Align LCD frame buffer to section boundary tegra: Support control of cache settings for LCD tegra: fdt: Add LCD definitions for Seaboard lcd: Add CONSOLE_SCROLL_LINES option to speed console Wei Ni (1): tegra: Add SOC support for display/lcd README | 16 + arch/arm/cpu/armv7/cache_v7.c | 11 + arch/arm/cpu/armv7/tegra2/Makefile | 1 + arch/arm/cpu/armv7/tegra2/display.c | 389 +++++++++++++++++ arch/arm/cpu/armv7/tegra2/funcmux.c | 38 ++ arch/arm/cpu/armv7/tegra2/pinmux.c | 4 +- arch/arm/cpu/armv7/tegra2/pwm.c | 99 +++++ arch/arm/dts/tegra20.dtsi | 96 +++++ arch/arm/include/asm/arch-tegra2/dc.h | 544 ++++++++++++++++++++++++ arch/arm/include/asm/arch-tegra2/display.h | 152 +++++++ arch/arm/include/asm/arch-tegra2/pinmux.h | 4 +- arch/arm/include/asm/arch-tegra2/pwm.h | 75 ++++ arch/arm/include/asm/system.h | 30 ++ arch/arm/lib/cache-cp15.c | 62 +++- board/nvidia/common/board.c | 24 +- board/nvidia/dts/tegra2-seaboard.dts | 32 ++ common/lcd.c | 86 +++- doc/device-tree-bindings/pwm/tegra20-pwm.txt | 18 + doc/device-tree-bindings/video/displaymode.txt | 42 ++ doc/device-tree-bindings/video/tegra20-dc.txt | 89 ++++ drivers/video/Makefile | 1 + drivers/video/tegra.c | 368 ++++++++++++++++ include/configs/seaboard.h | 11 +- include/configs/tegra2-common.h | 3 + include/fdtdec.h | 5 + include/lcd.h | 11 + lib/fdtdec.c | 29 +- 27 files changed, 2199 insertions(+), 41 deletions(-) create mode 100644 arch/arm/cpu/armv7/tegra2/display.c create mode 100644 arch/arm/cpu/armv7/tegra2/pwm.c create mode 100644 arch/arm/include/asm/arch-tegra2/dc.h create mode 100644 arch/arm/include/asm/arch-tegra2/display.h create mode 100644 arch/arm/include/asm/arch-tegra2/pwm.h create mode 100644 doc/device-tree-bindings/pwm/tegra20-pwm.txt create mode 100644 doc/device-tree-bindings/video/displaymode.txt create mode 100644 doc/device-tree-bindings/video/tegra20-dc.txt create mode 100644 drivers/video/tegra.c -- 1.7.7.3

9 64

[U-Boot] [PATCH 0/2] Support for msm7x27a board
by srikanth.reddy＠lntinfotech.com 19 Oct '12

19 Oct '12

From: Srikanth Reddy Vintha <srikanth.reddy(a)lntinfotech.com> This patch series contains the following support for msm7x27a * support for msm7x27a soc * support for msm7x27a surf board. Srikanth Reddy Vintha (2): MSM7x27a: Add support for qualcomm msm7x27a SOC. MSM7x27a: Add support for msm7x27a surf board arch/arm/cpu/armv7/msm7x27a/Makefile | 53 ++++ arch/arm/cpu/armv7/msm7x27a/acpuclock.c | 249 +++++++++++++++ arch/arm/cpu/armv7/msm7x27a/board.c | 66 ++++ arch/arm/cpu/armv7/msm7x27a/config.mk | 21 ++ arch/arm/cpu/armv7/msm7x27a/gpio.c | 284 +++++++++++++++++ arch/arm/cpu/armv7/msm7x27a/lowlevel_init.S | 118 +++++++ arch/arm/cpu/armv7/msm7x27a/timer.c | 127 ++++++++ arch/arm/include/asm/arch-msm7x27a/gpio.h | 47 +++ arch/arm/include/asm/arch-msm7x27a/iomap.h | 105 +++++++ arch/arm/include/asm/arch-msm7x27a/mmc.h | 399 ++++++++++++++++++++++++ arch/arm/include/asm/arch-msm7x27a/proc_comm.h | 42 +++ arch/arm/include/asm/arch-msm7x27a/sys_proto.h | 27 ++ board/qcom/msm7x27a_surf/Makefile | 56 ++++ board/qcom/msm7x27a_surf/msm7x27a_surf.c | 126 ++++++++ board/qcom/msm7x27a_surf/msm7x27a_surf.h | 27 ++ boards.cfg | 1 + include/configs/msm7x27a_surf.h | 128 ++++++++ 17 files changed, 1876 insertions(+), 0 deletions(-) create mode 100644 arch/arm/cpu/armv7/msm7x27a/Makefile create mode 100644 arch/arm/cpu/armv7/msm7x27a/acpuclock.c create mode 100644 arch/arm/cpu/armv7/msm7x27a/board.c create mode 100644 arch/arm/cpu/armv7/msm7x27a/config.mk create mode 100644 arch/arm/cpu/armv7/msm7x27a/gpio.c create mode 100644 arch/arm/cpu/armv7/msm7x27a/lowlevel_init.S create mode 100644 arch/arm/cpu/armv7/msm7x27a/timer.c create mode 100644 arch/arm/include/asm/arch-msm7x27a/gpio.h create mode 100644 arch/arm/include/asm/arch-msm7x27a/iomap.h create mode 100644 arch/arm/include/asm/arch-msm7x27a/mmc.h create mode 100644 arch/arm/include/asm/arch-msm7x27a/proc_comm.h create mode 100644 arch/arm/include/asm/arch-msm7x27a/sys_proto.h create mode 100644 board/qcom/msm7x27a_surf/Makefile create mode 100644 board/qcom/msm7x27a_surf/msm7x27a_surf.c create mode 100644 board/qcom/msm7x27a_surf/msm7x27a_surf.h create mode 100644 include/configs/msm7x27a_surf.h

2 4