July 2011 - U-Boot

[U-Boot] [PATCH v4 1/8] MX5: Add initial support for MX53 processor
by Jason Liu 13 Jul '11

13 Jul '11

Add initial support for Freescale MX53 processor, - Add the iomux support and the pin definition, - Add the regs definition, clean up some unused def from mx51, - Add the low level init support, make use the freq input of setup_pll macro --- Changes for v2: -address some comments of Stefano Babic, remove the is_soc_type and use #ifdef, -address the comments of stefano, remove CPU_TYPE def, remove something like /*0x760*/ comments in mx5x_pins.h. -fix the build break for vision2 board Changes for v3: -address some comments of Stefano -fix the offset of CLKCTL_CMEOR offset of MX53 -remove #define GPIO_PORT_NUM 4, not used now Signed-off-by: Jason Liu <r64343(a)freescale.com> --- arch/arm/cpu/armv7/mx5/iomux.c | 30 ++- arch/arm/cpu/armv7/mx5/lowlevel_init.S | 91 +++--- arch/arm/cpu/armv7/mx5/soc.c | 22 +- arch/arm/include/asm/arch-mx5/asm-offsets.h | 5 + arch/arm/include/asm/arch-mx5/imx-regs.h | 82 ++--- arch/arm/include/asm/arch-mx5/iomux.h | 102 ------ arch/arm/include/asm/arch-mx5/mx5x_pins.h | 469 ++++++++++++++++++++++++++- include/configs/mx51evk.h | 3 +- include/configs/vision2.h | 3 +- 9 files changed, 599 insertions(+), 208 deletions(-) diff --git a/arch/arm/cpu/armv7/mx5/iomux.c b/arch/arm/cpu/armv7/mx5/iomux.c old mode 100644 new mode 100755 index e8928d5..d4e3bbb --- a/arch/arm/cpu/armv7/mx5/iomux.c +++ b/arch/arm/cpu/armv7/mx5/iomux.c @@ -34,7 +34,7 @@ enum iomux_reg_addr { IOMUXSW_MUX_CTL = IOMUXC_BASE_ADDR, IOMUXSW_MUX_END = IOMUXC_BASE_ADDR + MUX_I_END, IOMUXSW_PAD_CTL = IOMUXC_BASE_ADDR + PAD_I_START, - IOMUXSW_INPUT_CTL = IOMUXC_BASE_ADDR, + IOMUXSW_INPUT_CTL = IOMUXC_BASE_ADDR + INPUT_CTL_START, }; #define MUX_PIN_NUM_MAX (((MUX_I_END - MUX_I_START) >> 2) + 1) @@ -44,11 +44,12 @@ static inline u32 get_mux_reg(iomux_pin_name_t pin) { u32 mux_reg = PIN_TO_IOMUX_MUX(pin); +#if defined(CONFIG_MX51) if (is_soc_rev(CHIP_REV_2_0) < 0) { /* * Fixup register address: - * i.MX51 TO1 has offset with the register - * which is define as TO2. + * i.MX51 TO1 has offset with the register + * which is define as TO2. */ if ((pin == MX51_PIN_NANDF_RB5) || (pin == MX51_PIN_NANDF_RB6) || @@ -59,6 +60,7 @@ static inline u32 get_mux_reg(iomux_pin_name_t pin) else if (mux_reg >= 0x130) mux_reg += 0xC; } +#endif mux_reg += IOMUXSW_MUX_CTL; return mux_reg; } @@ -68,11 +70,12 @@ static inline u32 get_pad_reg(iomux_pin_name_t pin) { u32 pad_reg = PIN_TO_IOMUX_PAD(pin); +#if defined(CONFIG_MX51) if (is_soc_rev(CHIP_REV_2_0) < 0) { /* * Fixup register address: - * i.MX51 TO1 has offset with the register - * which is define as TO2. + * i.MX51 TO1 has offset with the register + * which is define as TO2. */ if ((pin == MX51_PIN_NANDF_RB5) || (pin == MX51_PIN_NANDF_RB6) || @@ -91,6 +94,7 @@ static inline u32 get_pad_reg(iomux_pin_name_t pin) else pad_reg += 8; } +#endif pad_reg += IOMUXSW_PAD_CTL; return pad_reg; } @@ -98,10 +102,13 @@ static inline u32 get_pad_reg(iomux_pin_name_t pin) /* Get the last iomux register address */ static inline u32 get_mux_end(void) { +#if defined(CONFIG_MX51) if (is_soc_rev(CHIP_REV_2_0) < 0) return IOMUXC_BASE_ADDR + (0x3F8 - 4); else return IOMUXC_BASE_ADDR + (0x3F0 - 4); +#endif + return IOMUXSW_MUX_END; } /* @@ -164,3 +171,16 @@ unsigned int mxc_iomux_get_pad(iomux_pin_name_t pin) u32 pad_reg = get_pad_reg(pin); return readl(pad_reg); } + +/* + * This function configures daisy-chain + * + * @param input index of input select register + * @param config the binary value of elements + */ +void mxc_iomux_set_input(iomux_input_select_t input, u32 config) +{ + u32 reg = IOMUXSW_INPUT_CTL + (input << 2); + + writel(config, reg); +} diff --git a/arch/arm/cpu/armv7/mx5/lowlevel_init.S b/arch/arm/cpu/armv7/mx5/lowlevel_init.S old mode 100644 new mode 100755 index e984870..96ebfe2 --- a/arch/arm/cpu/armv7/mx5/lowlevel_init.S +++ b/arch/arm/cpu/armv7/mx5/lowlevel_init.S @@ -70,6 +70,7 @@ /* M4IF setup */ .macro init_m4if +#ifdef CONFIG_MX51 /* VPU and IPU given higher priority (0x4) * IPU accesses with ID=0x1 given highest priority (=0xA) */ @@ -87,27 +88,31 @@ ldr r1, =0x001901A3 str r1, [r0, #0x48] +#endif .endm /* init_m4if */ .macro setup_pll pll, freq - ldr r2, =\pll + ldr r0, =\pll ldr r1, =0x00001232 - str r1, [r2, #PLL_DP_CTL] /* Set DPLL ON (set UPEN bit): BRMO=1 */ + str r1, [r0, #PLL_DP_CTL] /* Set DPLL ON (set UPEN bit): BRMO=1 */ mov r1, #0x2 - str r1, [r2, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */ + str r1, [r0, #PLL_DP_CONFIG] /* Enable auto-restart AREN bit */ - str r3, [r2, #PLL_DP_OP] - str r3, [r2, #PLL_DP_HFS_OP] + ldr r1, W_DP_OP_\freq + str r1, [r0, #PLL_DP_OP] + str r1, [r0, #PLL_DP_HFS_OP] - str r4, [r2, #PLL_DP_MFD] - str r4, [r2, #PLL_DP_HFS_MFD] + ldr r1, W_DP_MFD_\freq + str r1, [r0, #PLL_DP_MFD] + str r1, [r0, #PLL_DP_HFS_MFD] - str r5, [r2, #PLL_DP_MFN] - str r5, [r2, #PLL_DP_HFS_MFN] + ldr r1, W_DP_MFN_\freq + str r1, [r0, #PLL_DP_MFN] + str r1, [r0, #PLL_DP_HFS_MFN] ldr r1, =0x00001232 - str r1, [r2, #PLL_DP_CTL] -1: ldr r1, [r2, #PLL_DP_CTL] + str r1, [r0, #PLL_DP_CTL] +1: ldr r1, [r0, #PLL_DP_CTL] ands r1, r1, #0x1 beq 1b .endm @@ -115,6 +120,7 @@ .macro init_clock ldr r0, =CCM_BASE_ADDR +#if defined(CONFIG_MX51) /* Gate of clocks to the peripherals first */ ldr r1, =0x3FFFFFFF str r1, [r0, #CLKCTL_CCGR0] @@ -141,19 +147,16 @@ 1: ldr r1, [r0, #CLKCTL_CDHIPR] cmp r1, #0x0 bne 1b +#endif /* Switch ARM to step clock */ mov r1, #0x4 str r1, [r0, #CLKCTL_CCSR] - mov r3, #DP_OP_800 - mov r4, #DP_MFD_800 - mov r5, #DP_MFN_800 - setup_pll PLL1_BASE_ADDR - mov r3, #DP_OP_665 - mov r4, #DP_MFD_665 - mov r5, #DP_MFN_665 - setup_pll PLL3_BASE_ADDR + setup_pll PLL1_BASE_ADDR, 800 + +#if defined(CONFIG_MX51) + setup_pll PLL3_BASE_ADDR, 665 /* Switch peripheral to PLL 3 */ ldr r0, =CCM_BASE_ADDR @@ -162,10 +165,7 @@ str r1, [r0, #CLKCTL_CBCMR] ldr r1, =0x13239145 str r1, [r0, #CLKCTL_CBCDR] - mov r3, #DP_OP_665 - mov r4, #DP_MFD_665 - mov r5, #DP_MFN_665 - setup_pll PLL2_BASE_ADDR + setup_pll PLL2_BASE_ADDR, 665 /* Switch peripheral to PLL2 */ ldr r0, =CCM_BASE_ADDR @@ -174,12 +174,8 @@ ldr r1, =0x000020C0 orr r1,r1,#CONFIG_SYS_DDR_CLKSEL str r1, [r0, #CLKCTL_CBCMR] - - mov r3, #DP_OP_216 - mov r4, #DP_MFD_216 - mov r5, #DP_MFN_216 - setup_pll PLL3_BASE_ADDR - +#endif + setup_pll PLL3_BASE_ADDR, 216 /* Set the platform clock dividers */ ldr r0, =ARM_BASE_ADDR @@ -188,18 +184,23 @@ ldr r0, =CCM_BASE_ADDR +#if defined(CONFIG_MX51) /* Run 3.0 at Full speed, for other TO's wait till we increase VDDGP */ ldr r1, =0x0 ldr r3, [r1, #ROM_SI_REV] cmp r3, #0x10 movls r1, #0x1 movhi r1, #0 - str r1, [r0, #CLKCTL_CACRR] +#else + mov r1, #0 +#endif + str r1, [r0, #CLKCTL_CACRR] /* Switch ARM back to PLL 1 */ mov r1, #0 str r1, [r0, #CLKCTL_CCSR] +#if defined(CONFIG_MX51) /* setup the rest */ /* Use lp_apm (24MHz) source for perclk */ ldr r1, =0x000020C2 @@ -208,6 +209,7 @@ /* ddr clock from PLL 1, all perclk dividers are 1 since using 24MHz */ ldr r1, =CONFIG_SYS_CLKTL_CBCDR str r1, [r0, #CLKCTL_CBCDR] +#endif /* Restore the default values in the Gate registers */ ldr r1, =0xFFFFFFFF @@ -218,13 +220,23 @@ str r1, [r0, #CLKCTL_CCGR4] str r1, [r0, #CLKCTL_CCGR5] str r1, [r0, #CLKCTL_CCGR6] +#if defined(CONFIG_MX53) + str r1, [r0, #CLKCTL_CCGR7] +#endif +#if defined(CONFIG_MX51) /* Use PLL 2 for UART's, get 66.5MHz from it */ ldr r1, =0xA5A2A020 str r1, [r0, #CLKCTL_CSCMR1] ldr r1, =0x00C30321 str r1, [r0, #CLKCTL_CSCDR1] - +#elif defined(CONFIG_MX53) + ldr r1, [r0, #CLKCTL_CSCDR1] + orr r1, r1, #0x3f + eor r1, r1, #0x3f + orr r1, r1, #0x21 + str r1, [r0, #CLKCTL_CSCDR1] +#endif /* make sure divider effective */ 1: ldr r1, [r0, #CLKCTL_CDHIPR] cmp r1, #0x0 @@ -249,6 +261,7 @@ .globl lowlevel_init lowlevel_init: +#if defined(CONFIG_MX51) ldr r0, =GPIO1_BASE_ADDR ldr r1, [r0, #0x0] orr r1, r1, #(1 << 23) @@ -256,6 +269,7 @@ lowlevel_init: ldr r1, [r0, #0x4] orr r1, r1, #(1 << 23) str r1, [r0, #0x4] +#endif init_l2cc @@ -269,9 +283,12 @@ lowlevel_init: mov pc,lr /* Board level setting value */ -DDR_PERCHARGE_CMD: .word 0x04008008 -DDR_REFRESH_CMD: .word 0x00008010 -DDR_LMR1_W: .word 0x00338018 -DDR_LMR_CMD: .word 0xB2220000 -DDR_TIMING_W: .word 0xB02567A9 -DDR_MISC_W: .word 0x000A0104 +W_DP_OP_800: .word DP_OP_800 +W_DP_MFD_800: .word DP_MFD_800 +W_DP_MFN_800: .word DP_MFN_800 +W_DP_OP_665: .word DP_OP_665 +W_DP_MFD_665: .word DP_MFD_665 +W_DP_MFN_665: .word DP_MFN_665 +W_DP_OP_216: .word DP_OP_216 +W_DP_MFD_216: .word DP_MFD_216 +W_DP_MFN_216: .word DP_MFN_216 diff --git a/arch/arm/cpu/armv7/mx5/soc.c b/arch/arm/cpu/armv7/mx5/soc.c index 2900119..09500b3 100644 --- a/arch/arm/cpu/armv7/mx5/soc.c +++ b/arch/arm/cpu/armv7/mx5/soc.c @@ -33,17 +33,20 @@ #include <fsl_esdhc.h> #endif -#if defined(CONFIG_MX51) -#define CPU_TYPE 0x51000 -#else +#if !(defined(CONFIG_MX51) || defined(CONFIG_MX53)) #error "CPU_TYPE not defined" #endif u32 get_cpu_rev(void) { - int system_rev = CPU_TYPE; +#ifdef CONFIG_MX51 + int system_rev = 0x51000; +#else + int system_rev = 0x53000; +#endif int reg = __raw_readl(ROM_SI_REV); +#if defined(CONFIG_MX51) switch (reg) { case 0x02: system_rev |= CHIP_REV_1_1; @@ -57,11 +60,20 @@ u32 get_cpu_rev(void) case 0x20: system_rev |= CHIP_REV_3_0; break; - return system_rev; default: system_rev |= CHIP_REV_1_0; break; } +#else + switch (reg) { + case 0x20: + system_rev |= CHIP_REV_2_0; + break; + default: + system_rev |= CHIP_REV_1_0; + break; + } +#endif return system_rev; } diff --git a/arch/arm/include/asm/arch-mx5/asm-offsets.h b/arch/arm/include/asm/arch-mx5/asm-offsets.h index afd2728..793f69c 100644 --- a/arch/arm/include/asm/arch-mx5/asm-offsets.h +++ b/arch/arm/include/asm/arch-mx5/asm-offsets.h @@ -37,7 +37,12 @@ #define CLKCTL_CCGR4 0x78 #define CLKCTL_CCGR5 0x7C #define CLKCTL_CCGR6 0x80 +#if defined(CONFIG_MX53) +#define CLKCTL_CCGR7 0x84 +#define CLKCTL_CMEOR 0x88 +#elif defined(CONFIG_MX51) #define CLKCTL_CMEOR 0x84 +#endif /* DPLL */ #define PLL_DP_CTL 0x00 diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h old mode 100644 new mode 100755 index b45026d..09b69f6 --- a/arch/arm/include/asm/arch-mx5/imx-regs.h +++ b/arch/arm/include/asm/arch-mx5/imx-regs.h @@ -20,38 +20,36 @@ * MA 02111-1307 USA */ -#ifndef __ASM_ARCH_MXC_MX51_H__ -#define __ASM_ARCH_MXC_MX51_H__ +#ifndef __ASM_ARCH_MX5_IMX_REGS_H__ +#define __ASM_ARCH_MX5_IMX_REGS_H__ -/* - * IRAM - */ +#if defined(CONFIG_MX51) #define IRAM_BASE_ADDR 0x1FFE0000 /* internal ram */ -#define IRAM_SIZE 0x00020000 /* 128 KB */ -/* - * Graphics Memory of GPU - */ -#define GPU_BASE_ADDR 0x20000000 -#define GPU_CTRL_BASE_ADDR 0x30000000 #define IPU_CTRL_BASE_ADDR 0x40000000 -/* - * Debug - */ -#define DEBUG_BASE_ADDR 0x60000000 -#define ETB_BASE_ADDR (DEBUG_BASE_ADDR + 0x00001000) -#define ETM_BASE_ADDR (DEBUG_BASE_ADDR + 0x00002000) -#define TPIU_BASE_ADDR (DEBUG_BASE_ADDR + 0x00003000) -#define CTI0_BASE_ADDR (DEBUG_BASE_ADDR + 0x00004000) -#define CTI1_BASE_ADDR (DEBUG_BASE_ADDR + 0x00005000) -#define CTI2_BASE_ADDR (DEBUG_BASE_ADDR + 0x00006000) -#define CTI3_BASE_ADDR (DEBUG_BASE_ADDR + 0x00007000) -#define CORTEX_DBG_BASE_ADDR (DEBUG_BASE_ADDR + 0x00008000) +#define SPBA0_BASE_ADDR 0x70000000 +#define AIPS1_BASE_ADDR 0x73F00000 +#define AIPS2_BASE_ADDR 0x83F00000 +#define CSD0_BASE_ADDR 0x90000000 +#define CSD1_BASE_ADDR 0xA0000000 +#define NFC_BASE_ADDR_AXI 0xCFFF0000 +#elif defined(CONFIG_MX53) +#define IPU_CTRL_BASE_ADDR 0x18000000 +#define SPBA0_BASE_ADDR 0x50000000 +#define AIPS1_BASE_ADDR 0x53F00000 +#define AIPS2_BASE_ADDR 0x63F00000 +#define CSD0_BASE_ADDR 0x70000000 +#define CSD1_BASE_ADDR 0xB0000000 +#define NFC_BASE_ADDR_AXI 0xF7FF0000 +#define IRAM_BASE_ADDR 0xF8000000 +#else +#error "CPU_TYPE not defined" +#endif + +#define IRAM_SIZE 0x00020000 /* 128 KB */ /* * SPBA global module enabled #0 */ -#define SPBA0_BASE_ADDR 0x70000000 - #define MMC_SDHC1_BASE_ADDR (SPBA0_BASE_ADDR + 0x00004000) #define MMC_SDHC2_BASE_ADDR (SPBA0_BASE_ADDR + 0x00008000) #define UART3_BASE_ADDR (SPBA0_BASE_ADDR + 0x0000C000) @@ -68,8 +66,6 @@ /* * AIPS 1 */ -#define AIPS1_BASE_ADDR 0x73F00000 - #define OTG_BASE_ADDR (AIPS1_BASE_ADDR + 0x00080000) #define GPIO1_BASE_ADDR (AIPS1_BASE_ADDR + 0x00084000) #define GPIO2_BASE_ADDR (AIPS1_BASE_ADDR + 0x00088000) @@ -91,11 +87,14 @@ #define CCM_BASE_ADDR (AIPS1_BASE_ADDR + 0x000D4000) #define GPC_BASE_ADDR (AIPS1_BASE_ADDR + 0x000D8000) +#if defined(CONFIG_MX53) +#define GPIO5_BASE_ADDR (AIPS1_BASE_ADDR + 0x000DC000) +#define GPIO6_BASE_ADDR (AIPS1_BASE_ADDR + 0x000E0000) +#define GPIO7_BASE_ADDR (AIPS1_BASE_ADDR + 0x000E4000) +#endif /* * AIPS 2 */ -#define AIPS2_BASE_ADDR 0x83F00000 - #define PLL1_BASE_ADDR (AIPS2_BASE_ADDR + 0x00080000) #define PLL2_BASE_ADDR (AIPS2_BASE_ADDR + 0x00084000) #define PLL3_BASE_ADDR (AIPS2_BASE_ADDR + 0x00088000) @@ -129,30 +128,7 @@ #define VPU_BASE_ADDR (AIPS2_BASE_ADDR + 0x000F4000) #define SAHARA_BASE_ADDR (AIPS2_BASE_ADDR + 0x000F8000) -#define TZIC_BASE_ADDR 0x8FFFC000 - /* - * Memory regions and CS - */ -#define CSD0_BASE_ADDR 0x90000000 -#define CSD1_BASE_ADDR 0xA0000000 -#define CS0_BASE_ADDR 0xB0000000 -#define CS1_BASE_ADDR 0xB8000000 -#define CS2_BASE_ADDR 0xC0000000 -#define CS3_BASE_ADDR 0xC8000000 -#define CS4_BASE_ADDR 0xCC000000 -#define CS5_BASE_ADDR 0xCE000000 - -/* - * NFC - */ -#define NFC_BASE_ADDR_AXI 0xCFFF0000 /* NAND flash AXI */ - -/*! - * Number of GPIO port as defined in the IC Spec - */ -#define GPIO_PORT_NUM 4 -/*! * Number of GPIO pins per port */ #define GPIO_NUM_PIN 32 @@ -311,4 +287,4 @@ struct fuse_bank1_regs { #endif /* __ASSEMBLER__*/ -#endif /* __ASM_ARCH_MXC_MX51_H__ */ +#endif /* __ASM_ARCH_MX5_IMX_REGS_H__ */ diff --git a/arch/arm/include/asm/arch-mx5/iomux.h b/arch/arm/include/asm/arch-mx5/iomux.h index 0d91a24..760371b 100644 --- a/arch/arm/include/asm/arch-mx5/iomux.h +++ b/arch/arm/include/asm/arch-mx5/iomux.h @@ -70,108 +70,6 @@ typedef enum iomux_pad_config { PAD_CTL_DRV_VOT_HIGH = 0x1 << 13,/* High voltage mode */ } iomux_pad_config_t; -/* various IOMUX input select register index */ -typedef enum iomux_input_select { - MUX_IN_AUDMUX_P4_INPUT_DA_AMX_SELECT_I = 0, - MUX_IN_AUDMUX_P4_INPUT_DB_AMX_SELECT_I, - MUX_IN_AUDMUX_P4_INPUT_TXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P4_INPUT_TXFS_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_DA_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_DB_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_RXFS_AMX_SELECT, - MUX_IN_AUDMUX_P5_INPUT_TXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P5_INPUT_TXFS_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_DA_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_DB_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_RXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_RXFS_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_TXCLK_AMX_SELECT_INPUT, - MUX_IN_AUDMUX_P6_INPUT_TXFS_AMX_SELECT_INPUT, - MUX_IN_CCM_IPP_DI_CLK_SELECT_INPUT, - /* TO2 */ - MUX_IN_CCM_IPP_DI1_CLK_SELECT_INPUT, - MUX_IN_CCM_PLL1_BYPASS_CLK_SELECT_INPUT, - MUX_IN_CCM_PLL2_BYPASS_CLK_SELECT_INPUT, - MUX_IN_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_MISO_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_MOSI_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_SS_B_1_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_SS_B_2_SELECT_INPUT, - MUX_IN_CSPI_IPP_IND_SS_B_3_SELECT_INPUT, - MUX_IN_DPLLIP1_L1T_TOG_EN_SELECT_INPUT, - /* TO2 */ - MUX_IN_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT, - MUX_IN_ECSPI2_IPP_IND_SS_B_3_SELECT_INPUT, - MUX_IN_EMI_IPP_IND_RDY_INT_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT0_IN_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT1_IN_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT2_IN_SELECT_INPUT, - MUX_IN_ESDHC3_IPP_DAT3_IN_SELECT_INPUT, - MUX_IN_FEC_FEC_COL_SELECT_INPUT, - MUX_IN_FEC_FEC_CRS_SELECT_INPUT, - MUX_IN_FEC_FEC_MDI_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_0_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_1_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_2_SELECT_INPUT, - MUX_IN_FEC_FEC_RDATA_3_SELECT_INPUT, - MUX_IN_FEC_FEC_RX_CLK_SELECT_INPUT, - MUX_IN_FEC_FEC_RX_DV_SELECT_INPUT, - MUX_IN_FEC_FEC_RX_ER_SELECT_INPUT, - MUX_IN_FEC_FEC_TX_CLK_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_1_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_2_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_3_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_5_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_6_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_7_SELECT_INPUT, - MUX_IN_GPIO3_IPP_IND_G_IN_8_SELECT_INPUT, - /* TO2 */ - MUX_IN_GPIO3_IPP_IND_G_IN_12_SELECT_INPUT, - MUX_IN_HSC_MIPI_MIX_IPP_IND_SENS1_DATA_EN_SELECT_INPUT, - MUX_IN_HSC_MIPI_MIX_IPP_IND_SENS2_DATA_EN_SELECT_INPUT, - /* TO2 */ - MUX_IN_HSC_MIPI_MIX_PAR_VSYNC_SELECT_INPUT, - /* TO2 */ - MUX_IN_HSC_MIPI_MIX_PAR_DI_WAIT_SELECT_INPUT, - MUX_IN_HSC_MIPI_MIX_PAR_SISG_TRIG_SELECT_INPUT, - MUX_IN_I2C1_IPP_SCL_IN_SELECT_INPUT, - MUX_IN_I2C1_IPP_SDA_IN_SELECT_INPUT, - MUX_IN_I2C2_IPP_SCL_IN_SELECT_INPUT, - MUX_IN_I2C2_IPP_SDA_IN_SELECT_INPUT, - - MUX_IN_IPU_IPP_DI_0_IND_DISPB_SD_D_SELECT_INPUT, - - MUX_IN_IPU_IPP_DI_1_IND_DISPB_SD_D_SELECT_INPUT, - - MUX_IN_KPP_IPP_IND_COL_6_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_COL_7_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_4_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_5_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_6_SELECT_INPUT, - MUX_IN_KPP_IPP_IND_ROW_7_SELECT_INPUT, - MUX_IN_UART1_IPP_UART_RTS_B_SELECT_INPUT, - MUX_IN_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, - MUX_IN_UART2_IPP_UART_RTS_B_SELECT_INPUT, - MUX_IN_UART2_IPP_UART_RXD_MUX_SELECT_INPUT, - MUX_IN_UART3_IPP_UART_RTS_B_SELECT_INPUT, - MUX_IN_UART3_IPP_UART_RXD_MUX_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_CLK_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_0_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_1_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_2_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_3_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_4_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_5_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_6_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DATA_7_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_DIR_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_NXT_SELECT_INPUT, - MUX_IN_USBOH3_IPP_IND_UH3_STP_SELECT_INPUT, - MUX_INPUT_NUM_MUX, -} iomux_input_select_t; - /* various IOMUX input functions */ typedef enum iomux_input_config { INPUT_CTL_PATH0 = 0x0, diff --git a/arch/arm/include/asm/arch-mx5/mx5x_pins.h b/arch/arm/include/asm/arch-mx5/mx5x_pins.h old mode 100644 new mode 100755 index a564fce..4e3a31b --- a/arch/arm/include/asm/arch-mx5/mx5x_pins.h +++ b/arch/arm/include/asm/arch-mx5/mx5x_pins.h @@ -86,12 +86,22 @@ #define PIN_TO_PAD_MASK ((1 << (GPIO_I - PAD_I)) - 1) #define PIN_TO_ALT_GPIO_MASK ((1 << (MUX_IO_I - GPIO_I)) - 1) -#define NON_MUX_I PIN_TO_MUX_MASK +#define NON_MUX_I PIN_TO_MUX_MASK +#define NON_PAD_I PIN_TO_PAD_MASK + +#if defined(CONFIG_MX51) #define MUX_I_START 0x001C #define PAD_I_START 0x3F0 #define INPUT_CTL_START 0x8C4 -#define INPUT_CTL_START_TO1 0x928 #define MUX_I_END (PAD_I_START - 4) +#elif defined(CONFIG_MX53) +#define MUX_I_START 0x0020 +#define PAD_I_START 0x348 +#define INPUT_CTL_START 0x730 +#define MUX_I_END (PAD_I_START - 4) +#else +#error "CPU_TYPE not defined" +#endif #define _MXC_BUILD_PIN(gp, gi, ga, mi, pi) \ (((gp) << MUX_IO_P) | ((gi) << MUX_IO_I) | \ @@ -115,7 +125,7 @@ * "sw_pad_ctl & sw_mux_ctl details" of the MX51 IC Spec. Each enumerated * value is constructed based on the rules described above. */ -enum iomux_pins { +enum { MX51_PIN_EIM_DA0 = _MXC_BUILD_NON_GPIO_PIN(0x1C, 0x7A8), MX51_PIN_EIM_DA1 = _MXC_BUILD_NON_GPIO_PIN(0x20, 0x7A8), MX51_PIN_EIM_DA2 = _MXC_BUILD_NON_GPIO_PIN(0x24, 0x7A8), @@ -414,5 +424,458 @@ enum iomux_pins { MX51_PIN_CTL_DRAM_DQM3 = _MXC_BUILD_NON_GPIO_PIN(0, 0x4E0), }; +enum { + MX53_PIN_GPIO_19 = _MXC_BUILD_GPIO_PIN(3, 5, 1, 0x20, 0x348), + MX53_PIN_KEY_COL0 = _MXC_BUILD_GPIO_PIN(3, 6, 1, 0x24, 0x34C), + MX53_PIN_KEY_ROW0 = _MXC_BUILD_GPIO_PIN(3, 7, 1, 0x28, 0x350), + MX53_PIN_KEY_COL1 = _MXC_BUILD_GPIO_PIN(3, 8, 1, 0x2C, 0x354), + MX53_PIN_KEY_ROW1 = _MXC_BUILD_GPIO_PIN(3, 9, 1, 0x30, 0x358), + MX53_PIN_KEY_COL2 = _MXC_BUILD_GPIO_PIN(3, 10, 1, 0x34, 0x35C), + MX53_PIN_KEY_ROW2 = _MXC_BUILD_GPIO_PIN(3, 11, 1, 0x38, 0x360), + MX53_PIN_KEY_COL3 = _MXC_BUILD_GPIO_PIN(3, 12, 1, 0x3C, 0x364), + MX53_PIN_KEY_ROW3 = _MXC_BUILD_GPIO_PIN(3, 13, 1, 0x40, 0x368), + MX53_PIN_KEY_COL4 = _MXC_BUILD_GPIO_PIN(3, 14, 1, 0x44, 0x36C), + MX53_PIN_KEY_ROW4 = _MXC_BUILD_GPIO_PIN(3, 15, 1, 0x48, 0x370), + MX53_PIN_NVCC_KEYPAD = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x374), + MX53_PIN_DI0_DISP_CLK = _MXC_BUILD_GPIO_PIN(3, 16, 1, 0x4C, 0x378), + MX53_PIN_DI0_PIN15 = _MXC_BUILD_GPIO_PIN(3, 17, 1, 0x50, 0x37C), + MX53_PIN_DI0_PIN2 = _MXC_BUILD_GPIO_PIN(3, 18, 1, 0x54, 0x380), + MX53_PIN_DI0_PIN3 = _MXC_BUILD_GPIO_PIN(3, 19, 1, 0x58, 0x384), + MX53_PIN_DI0_PIN4 = _MXC_BUILD_GPIO_PIN(3, 20, 1, 0x5C, 0x388), + MX53_PIN_DISP0_DAT0 = _MXC_BUILD_GPIO_PIN(3, 21, 1, 0x60, 0x38C), + MX53_PIN_DISP0_DAT1 = _MXC_BUILD_GPIO_PIN(3, 22, 1, 0x64, 0x390), + MX53_PIN_DISP0_DAT2 = _MXC_BUILD_GPIO_PIN(3, 23, 1, 0x68, 0x394), + MX53_PIN_DISP0_DAT3 = _MXC_BUILD_GPIO_PIN(3, 24, 1, 0x6C, 0x398), + MX53_PIN_DISP0_DAT4 = _MXC_BUILD_GPIO_PIN(3, 25, 1, 0x70, 0x39C), + MX53_PIN_DISP0_DAT5 = _MXC_BUILD_GPIO_PIN(3, 26, 1, 0x74, 0x3A0), + MX53_PIN_DISP0_DAT6 = _MXC_BUILD_GPIO_PIN(3, 27, 1, 0x78, 0x3A4), + MX53_PIN_DISP0_DAT7 = _MXC_BUILD_GPIO_PIN(3, 28, 1, 0x7C, 0x3A8), + MX53_PIN_DISP0_DAT8 = _MXC_BUILD_GPIO_PIN(3, 29, 1, 0x80, 0x3AC), + MX53_PIN_DISP0_DAT9 = _MXC_BUILD_GPIO_PIN(3, 30, 1, 0x84, 0x3B0), + MX53_PIN_DISP0_DAT10 = _MXC_BUILD_GPIO_PIN(3, 31, 1, 0x88, 0x3B4), + MX53_PIN_DISP0_DAT11 = _MXC_BUILD_GPIO_PIN(4, 5, 1, 0x8C, 0x3B8), + MX53_PIN_DISP0_DAT12 = _MXC_BUILD_GPIO_PIN(4, 6, 1, 0x90, 0x3BC), + MX53_PIN_DISP0_DAT13 = _MXC_BUILD_GPIO_PIN(4, 7, 1, 0x94, 0x3C0), + MX53_PIN_DISP0_DAT14 = _MXC_BUILD_GPIO_PIN(4, 8, 1, 0x98, 0x3C4), + MX53_PIN_DISP0_DAT15 = _MXC_BUILD_GPIO_PIN(4, 9, 1, 0x9C, 0x3C8), + MX53_PIN_DISP0_DAT16 = _MXC_BUILD_GPIO_PIN(4, 10, 1, 0xA0, 0x3CC), + MX53_PIN_DISP0_DAT17 = _MXC_BUILD_GPIO_PIN(4, 11, 1, 0xA4, 0x3D0), + MX53_PIN_DISP0_DAT18 = _MXC_BUILD_GPIO_PIN(4, 12, 1, 0xA8, 0x3D4), + MX53_PIN_DISP0_DAT19 = _MXC_BUILD_GPIO_PIN(4, 13, 1, 0xAC, 0x3D8), + MX53_PIN_DISP0_DAT20 = _MXC_BUILD_GPIO_PIN(4, 14, 1, 0xB0, 0x3DC), + MX53_PIN_DISP0_DAT21 = _MXC_BUILD_GPIO_PIN(4, 15, 1, 0xB4, 0x3E0), + MX53_PIN_DISP0_DAT22 = _MXC_BUILD_GPIO_PIN(4, 16, 1, 0xB8, 0x3E4), + MX53_PIN_DISP0_DAT23 = _MXC_BUILD_GPIO_PIN(4, 17, 1, 0xBC, 0x3E8), + MX53_PIN_CSI0_PIXCLK = _MXC_BUILD_GPIO_PIN(4, 18, 1, 0xC0, 0x3EC), + MX53_PIN_CSI0_MCLK = _MXC_BUILD_GPIO_PIN(4, 19, 1, 0xC4, 0x3F0), + MX53_PIN_CSI0_DATA_EN = _MXC_BUILD_GPIO_PIN(4, 20, 1, 0xC8, 0x3F4), + MX53_PIN_CSI0_VSYNC = _MXC_BUILD_GPIO_PIN(4, 21, 1, 0xCC, 0x3F8), + MX53_PIN_CSI0_D4 = _MXC_BUILD_GPIO_PIN(4, 22, 1, 0xD0, 0x3FC), + MX53_PIN_CSI0_D5 = _MXC_BUILD_GPIO_PIN(4, 23, 1, 0xD4, 0x400), + MX53_PIN_CSI0_D6 = _MXC_BUILD_GPIO_PIN(4, 24, 1, 0xD8, 0x404), + MX53_PIN_CSI0_D7 = _MXC_BUILD_GPIO_PIN(4, 25, 1, 0xDC, 0x408), + MX53_PIN_CSI0_D8 = _MXC_BUILD_GPIO_PIN(4, 26, 1, 0xE0, 0x40C), + MX53_PIN_CSI0_D9 = _MXC_BUILD_GPIO_PIN(4, 27, 1, 0xE4, 0x410), + MX53_PIN_CSI0_D10 = _MXC_BUILD_GPIO_PIN(4, 28, 1, 0xE8, 0x414), + MX53_PIN_CSI0_D11 = _MXC_BUILD_GPIO_PIN(4, 29, 1, 0xEC, 0x418), + MX53_PIN_CSI0_D12 = _MXC_BUILD_GPIO_PIN(4, 30, 1, 0xF0, 0x41C), + MX53_PIN_CSI0_D13 = _MXC_BUILD_GPIO_PIN(4, 31, 1, 0xF4, 0x420), + MX53_PIN_CSI0_D14 = _MXC_BUILD_GPIO_PIN(5, 0, 1, 0xF8, 0x424), + MX53_PIN_CSI0_D15 = _MXC_BUILD_GPIO_PIN(5, 1, 1, 0xFC, 0x428), + MX53_PIN_CSI0_D16 = _MXC_BUILD_GPIO_PIN(5, 2, 1, 0x100, 0x42C), + MX53_PIN_CSI0_D17 = _MXC_BUILD_GPIO_PIN(5, 3, 1, 0x104, 0x430), + MX53_PIN_CSI0_D18 = _MXC_BUILD_GPIO_PIN(5, 4, 1, 0x108, 0x434), + MX53_PIN_CSI0_D19 = _MXC_BUILD_GPIO_PIN(5, 5, 1, 0x10C, 0x438), + MX53_PIN_NVCC_CSI0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x43C), + MX53_PIN_JTAG_TMS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x440), + MX53_PIN_JTAG_MOD = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x444), + MX53_PIN_JTAG_TRSTB = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x448), + MX53_PIN_JTAG_TDI = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x44C), + MX53_PIN_JTAG_TCK = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x450), + MX53_PIN_JTAG_TDO = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x454), + MX53_PIN_EIM_A25 = _MXC_BUILD_GPIO_PIN(4, 2, 1, 0x110, 0x458), + MX53_PIN_EIM_EB2 = _MXC_BUILD_GPIO_PIN(1, 30, 1, 0x114, 0x45C), + MX53_PIN_EIM_D16 = _MXC_BUILD_GPIO_PIN(2, 16, 1, 0x118, 0x460), + MX53_PIN_EIM_D17 = _MXC_BUILD_GPIO_PIN(2, 17, 1, 0x11C, 0x464), + MX53_PIN_EIM_D18 = _MXC_BUILD_GPIO_PIN(2, 18, 1, 0x120, 0x468), + MX53_PIN_EIM_D19 = _MXC_BUILD_GPIO_PIN(2, 19, 1, 0x124, 0x46C), + MX53_PIN_EIM_D20 = _MXC_BUILD_GPIO_PIN(2, 20, 1, 0x128, 0x470), + MX53_PIN_EIM_D21 = _MXC_BUILD_GPIO_PIN(2, 21, 1, 0x12C, 0x474), + MX53_PIN_EIM_D22 = _MXC_BUILD_GPIO_PIN(2, 22, 1, 0x130, 0x478), + MX53_PIN_EIM_D23 = _MXC_BUILD_GPIO_PIN(2, 23, 1, 0x134, 0x47C), + MX53_PIN_EIM_EB3 = _MXC_BUILD_GPIO_PIN(1, 31, 1, 0x138, 0x480), + MX53_PIN_EIM_D24 = _MXC_BUILD_GPIO_PIN(2, 24, 1, 0x13C, 0x484), + MX53_PIN_EIM_D25 = _MXC_BUILD_GPIO_PIN(2, 25, 1, 0x140, 0x488), + MX53_PIN_EIM_D26 = _MXC_BUILD_GPIO_PIN(2, 26, 1, 0x144, 0x48C), + MX53_PIN_EIM_D27 = _MXC_BUILD_GPIO_PIN(2, 27, 1, 0x148, 0x490), + MX53_PIN_EIM_D28 = _MXC_BUILD_GPIO_PIN(2, 28, 1, 0x14C, 0x494), + MX53_PIN_EIM_D29 = _MXC_BUILD_GPIO_PIN(2, 29, 1, 0x150, 0x498), + MX53_PIN_EIM_D30 = _MXC_BUILD_GPIO_PIN(2, 30, 1, 0x154, 0x49C), + MX53_PIN_EIM_D31 = _MXC_BUILD_GPIO_PIN(2, 31, 1, 0x158, 0x4A0), + MX53_PIN_NVCC_EIM1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x4A4), + MX53_PIN_EIM_A24 = _MXC_BUILD_GPIO_PIN(4, 4, 1, 0x15C, 0x4A8), + MX53_PIN_EIM_A23 = _MXC_BUILD_GPIO_PIN(5, 6, 1, 0x160, 0x4AC), + MX53_PIN_EIM_A22 = _MXC_BUILD_GPIO_PIN(1, 16, 1, 0x164, 0x4B0), + MX53_PIN_EIM_A21 = _MXC_BUILD_GPIO_PIN(1, 17, 1, 0x168, 0x4B4), + MX53_PIN_EIM_A20 = _MXC_BUILD_GPIO_PIN(1, 18, 1, 0x16C, 0x4B8), + MX53_PIN_EIM_A19 = _MXC_BUILD_GPIO_PIN(1, 19, 1, 0x170, 0x4BC), + MX53_PIN_EIM_A18 = _MXC_BUILD_GPIO_PIN(1, 20, 1, 0x174, 0x4C0), + MX53_PIN_EIM_A17 = _MXC_BUILD_GPIO_PIN(1, 21, 1, 0x178, 0x4C4), + MX53_PIN_EIM_A16 = _MXC_BUILD_GPIO_PIN(1, 22, 1, 0x17C, 0x4C8), + MX53_PIN_EIM_CS0 = _MXC_BUILD_GPIO_PIN(1, 23, 1, 0x180, 0x4CC), + MX53_PIN_EIM_CS1 = _MXC_BUILD_GPIO_PIN(1, 24, 1, 0x184, 0x4D0), + MX53_PIN_EIM_OE = _MXC_BUILD_GPIO_PIN(1, 25, 1, 0x188, 0x4D4), + MX53_PIN_EIM_RW = _MXC_BUILD_GPIO_PIN(1, 26, 1, 0x18C, 0x4D8), + MX53_PIN_EIM_LBA = _MXC_BUILD_GPIO_PIN(1, 27, 1, 0x190, 0x4DC), + MX53_PIN_NVCC_EIM4 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x4E0), + MX53_PIN_EIM_EB0 = _MXC_BUILD_GPIO_PIN(1, 28, 1, 0x194, 0x4E4), + MX53_PIN_EIM_EB1 = _MXC_BUILD_GPIO_PIN(1, 29, 1, 0x198, 0x4E8), + MX53_PIN_EIM_DA0 = _MXC_BUILD_GPIO_PIN(2, 0, 1, 0x19C, 0x4EC), + MX53_PIN_EIM_DA1 = _MXC_BUILD_GPIO_PIN(2, 1, 1, 0x1A0, 0x4F0), + MX53_PIN_EIM_DA2 = _MXC_BUILD_GPIO_PIN(2, 2, 1, 0x1A4, 0x4F4), + MX53_PIN_EIM_DA3 = _MXC_BUILD_GPIO_PIN(2, 3, 1, 0x1A8, 0x4F8), + MX53_PIN_EIM_DA4 = _MXC_BUILD_GPIO_PIN(2, 4, 1, 0x1AC, 0x4FC), + MX53_PIN_EIM_DA5 = _MXC_BUILD_GPIO_PIN(2, 5, 1, 0x1B0, 0x500), + MX53_PIN_EIM_DA6 = _MXC_BUILD_GPIO_PIN(2, 6, 1, 0x1B4, 0x504), + MX53_PIN_EIM_DA7 = _MXC_BUILD_GPIO_PIN(2, 7, 1, 0x1B8, 0x508), + MX53_PIN_EIM_DA8 = _MXC_BUILD_GPIO_PIN(2, 8, 1, 0x1BC, 0x50C), + MX53_PIN_EIM_DA9 = _MXC_BUILD_GPIO_PIN(2, 9, 1, 0x1C0, 0x510), + MX53_PIN_EIM_DA10 = _MXC_BUILD_GPIO_PIN(2, 10, 1, 0x1C4, 0x514), + MX53_PIN_EIM_DA11 = _MXC_BUILD_GPIO_PIN(2, 11, 1, 0x1C8, 0x518), + MX53_PIN_EIM_DA12 = _MXC_BUILD_GPIO_PIN(2, 12, 1, 0x1CC, 0x51C), + MX53_PIN_EIM_DA13 = _MXC_BUILD_GPIO_PIN(2, 13, 1, 0x1D0, 0x520), + MX53_PIN_EIM_DA14 = _MXC_BUILD_GPIO_PIN(2, 14, 1, 0x1D4, 0x524), + MX53_PIN_EIM_DA15 = _MXC_BUILD_GPIO_PIN(2, 15, 1, 0x1D8, 0x528), + MX53_PIN_NANDF_WE_B = _MXC_BUILD_GPIO_PIN(5, 12, 1, 0x1DC, 0x52C), + MX53_PIN_NANDF_RE_B = _MXC_BUILD_GPIO_PIN(5, 13, 1, 0x1E0, 0x530), + MX53_PIN_EIM_WAIT = _MXC_BUILD_GPIO_PIN(4, 0, 1, 0x1E4, 0x534), + MX53_PIN_EIM_BCLK = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x538), + MX53_PIN_NVCC_EIM7 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x53C), + MX53_PIN_LVDS1_TX3_P = _MXC_BUILD_GPIO_PIN(5, 22, 0, 0x1EC, NON_PAD_I), + MX53_PIN_LVDS1_TX2_P = _MXC_BUILD_GPIO_PIN(5, 24, 0, 0x1F0, NON_PAD_I), + MX53_PIN_LVDS1_CLK_P = _MXC_BUILD_GPIO_PIN(5, 26, 0, 0x1F4, NON_PAD_I), + MX53_PIN_LVDS1_TX1_P = _MXC_BUILD_GPIO_PIN(5, 28, 0, 0x1F8, NON_PAD_I), + MX53_PIN_LVDS1_TX0_P = _MXC_BUILD_GPIO_PIN(5, 30, 0, 0x1FC, NON_PAD_I), + MX53_PIN_LVDS0_TX3_P = _MXC_BUILD_GPIO_PIN(6, 22, 0, 0x200, NON_PAD_I), + MX53_PIN_LVDS0_CLK_P = _MXC_BUILD_GPIO_PIN(6, 24, 0, 0x204, NON_PAD_I), + MX53_PIN_LVDS0_TX2_P = _MXC_BUILD_GPIO_PIN(6, 26, 0, 0x208, NON_PAD_I), + MX53_PIN_LVDS0_TX1_P = _MXC_BUILD_GPIO_PIN(6, 28, 0, 0x20C, NON_PAD_I), + MX53_PIN_LVDS0_TX0_P = _MXC_BUILD_GPIO_PIN(6, 30, 0, 0x210, NON_PAD_I), + MX53_PIN_GPIO_10 = _MXC_BUILD_GPIO_PIN(3, 0, 0, 0x214, 0x540), + MX53_PIN_GPIO_11 = _MXC_BUILD_GPIO_PIN(3, 1, 0, 0x218, 0x544), + MX53_PIN_GPIO_12 = _MXC_BUILD_GPIO_PIN(3, 2, 0, 0x21C, 0x548), + MX53_PIN_GPIO_13 = _MXC_BUILD_GPIO_PIN(3, 3, 0, 0x220, 0x54C), + MX53_PIN_GPIO_14 = _MXC_BUILD_GPIO_PIN(3, 4, 0, 0x224, 0x550), + MX53_PIN_DRAM_DQM3 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x554), + MX53_PIN_DRAM_SDQS3 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x558), + MX53_PIN_DRAM_SDCKE1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x55C), + MX53_PIN_DRAM_DQM2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x560), + MX53_PIN_DRAM_SDODT1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x564), + MX53_PIN_DRAM_SDQS2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x568), + MX53_PIN_DRAM_RESET = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x56C), + MX53_PIN_DRAM_SDCLK1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x570), + MX53_PIN_DRAM_CAS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x574), + MX53_PIN_DRAM_SDCLK0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x578), + MX53_PIN_DRAM_SDQS0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x57C), + MX53_PIN_DRAM_SDODT0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x580), + MX53_PIN_DRAM_DQM0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x584), + MX53_PIN_DRAM_RAS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x588), + MX53_PIN_DRAM_SDCKE0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x58C), + MX53_PIN_DRAM_SDQS1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x590), + MX53_PIN_DRAM_DQM1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x594), + MX53_PIN_PMIC_ON_REQ = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x598), + MX53_PIN_PMIC_STBY_REQ = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x59C), + MX53_PIN_NANDF_CLE = _MXC_BUILD_GPIO_PIN(5, 7, 1, 0x228, 0x5A0), + MX53_PIN_NANDF_ALE = _MXC_BUILD_GPIO_PIN(5, 8 , 1, 0x22C, 0x5A4), + MX53_PIN_NANDF_WP_B = _MXC_BUILD_GPIO_PIN(5, 9, 1, 0x230, 0x5A8), + MX53_PIN_NANDF_RB0 = _MXC_BUILD_GPIO_PIN(5, 10, 1, 0x234, 0x5AC), + MX53_PIN_NANDF_CS0 = _MXC_BUILD_GPIO_PIN(5, 11, 1, 0x238, 0x5B0), + MX53_PIN_NANDF_CS1 = _MXC_BUILD_GPIO_PIN(5, 14, 1, 0x23C, 0x5B4), + MX53_PIN_NANDF_CS2 = _MXC_BUILD_GPIO_PIN(5, 15, 1, 0x240, 0x5B8), + MX53_PIN_NANDF_CS3 = _MXC_BUILD_GPIO_PIN(5, 16, 1, 0x244, 0x5BC), + MX53_PIN_NVCC_NANDF = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x5C0), + MX53_PIN_FEC_MDIO = _MXC_BUILD_GPIO_PIN(0, 22, 1, 0x248, 0x5C4), + MX53_PIN_FEC_REF_CLK = _MXC_BUILD_GPIO_PIN(0, 23, 1, 0x24C, 0x5C8), + MX53_PIN_FEC_RX_ER = _MXC_BUILD_GPIO_PIN(0, 24, 1, 0x250, 0x5CC), + MX53_PIN_FEC_CRS_DV = _MXC_BUILD_GPIO_PIN(0, 25, 1, 0x254, 0x5D0), + MX53_PIN_FEC_RXD1 = _MXC_BUILD_GPIO_PIN(0, 26, 1, 0x258, 0x5D4), + MX53_PIN_FEC_RXD0 = _MXC_BUILD_GPIO_PIN(0, 27, 1, 0x25C, 0x5D8), + MX53_PIN_FEC_TX_EN = _MXC_BUILD_GPIO_PIN(0, 28, 1, 0x260, 0x5DC), + MX53_PIN_FEC_TXD1 = _MXC_BUILD_GPIO_PIN(0, 29, 1, 0x264, 0x5E0), + MX53_PIN_FEC_TXD0 = _MXC_BUILD_GPIO_PIN(0, 30, 1, 0x268, 0x5E4), + MX53_PIN_FEC_MDC = _MXC_BUILD_GPIO_PIN(0, 31, 1, 0x26C, 0x5E8), + MX53_PIN_NVCC_FEC = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x5EC), + MX53_PIN_ATA_DIOW = _MXC_BUILD_GPIO_PIN(5, 17, 1, 0x270, 0x5F0), + MX53_PIN_ATA_DMACK = _MXC_BUILD_GPIO_PIN(5, 18, 1, 0x274, 0x5F4), + MX53_PIN_ATA_DMARQ = _MXC_BUILD_GPIO_PIN(6, 0, 1, 0x278, 0x5F8), + MX53_PIN_ATA_BUFFER_EN = _MXC_BUILD_GPIO_PIN(6, 1, 1, 0x27C, 0x5FC), + MX53_PIN_ATA_INTRQ = _MXC_BUILD_GPIO_PIN(6, 2, 1, 0x280, 0x600), + MX53_PIN_ATA_DIOR = _MXC_BUILD_GPIO_PIN(6, 3, 1, 0x284, 0x604), + MX53_PIN_ATA_RESET_B = _MXC_BUILD_GPIO_PIN(6, 4, 1, 0x288, 0x608), + MX53_PIN_ATA_IORDY = _MXC_BUILD_GPIO_PIN(6, 5, 1, 0x28C, 0x60C), + MX53_PIN_ATA_DA_0 = _MXC_BUILD_GPIO_PIN(6, 6, 1, 0x290, 0x610), + MX53_PIN_ATA_DA_1 = _MXC_BUILD_GPIO_PIN(6, 7, 1, 0x294, 0x614), + MX53_PIN_ATA_DA_2 = _MXC_BUILD_GPIO_PIN(6, 8, 1, 0x298, 0x618), + MX53_PIN_ATA_CS_0 = _MXC_BUILD_GPIO_PIN(6, 9, 1, 0x29C, 0x61C), + MX53_PIN_ATA_CS_1 = _MXC_BUILD_GPIO_PIN(6, 10, 1, 0x2A0, 0x620), + MX53_PIN_NVCC_ATA2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x624), + MX53_PIN_ATA_DATA0 = _MXC_BUILD_GPIO_PIN(1, 0, 1, 0x2A4, 0x628), + MX53_PIN_ATA_DATA1 = _MXC_BUILD_GPIO_PIN(1, 1, 1, 0x2A8, 0x62C), + MX53_PIN_ATA_DATA2 = _MXC_BUILD_GPIO_PIN(1, 2, 1, 0x2AC, 0x630), + MX53_PIN_ATA_DATA3 = _MXC_BUILD_GPIO_PIN(1, 3, 1, 0x2B0, 0x634), + MX53_PIN_ATA_DATA4 = _MXC_BUILD_GPIO_PIN(1, 4, 1, 0x2B4, 0x638), + MX53_PIN_ATA_DATA5 = _MXC_BUILD_GPIO_PIN(1, 5, 1, 0x2B8, 0x63C), + MX53_PIN_ATA_DATA6 = _MXC_BUILD_GPIO_PIN(1, 6, 1, 0x2BC, 0x640), + MX53_PIN_ATA_DATA7 = _MXC_BUILD_GPIO_PIN(1, 7, 1, 0x2C0, 0x644), + MX53_PIN_ATA_DATA8 = _MXC_BUILD_GPIO_PIN(1, 8, 1, 0x2C4, 0x648), + MX53_PIN_ATA_DATA9 = _MXC_BUILD_GPIO_PIN(1, 9, 1, 0x2C8, 0x64C), + MX53_PIN_ATA_DATA10 = _MXC_BUILD_GPIO_PIN(1, 10, 1, 0x2CC, 0x650), + MX53_PIN_ATA_DATA11 = _MXC_BUILD_GPIO_PIN(1, 11, 1, 0x2D0, 0x654), + MX53_PIN_ATA_DATA12 = _MXC_BUILD_GPIO_PIN(1, 12, 1, 0x2D4, 0x658), + MX53_PIN_ATA_DATA13 = _MXC_BUILD_GPIO_PIN(1, 13, 1, 0x2D8, 0x65C), + MX53_PIN_ATA_DATA14 = _MXC_BUILD_GPIO_PIN(1, 14, 1, 0x2DC, 0x660), + MX53_PIN_ATA_DATA15 = _MXC_BUILD_GPIO_PIN(1, 15, 1, 0x2E0, 0x664), + MX53_PIN_NVCC_ATA0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x668), + MX53_PIN_SD1_DATA0 = _MXC_BUILD_GPIO_PIN(0, 16, 1, 0x2E4, 0x66C), + MX53_PIN_SD1_DATA1 = _MXC_BUILD_GPIO_PIN(0, 17, 1, 0x2E8, 0x670), + MX53_PIN_SD1_CMD = _MXC_BUILD_GPIO_PIN(0, 18, 1, 0x2EC, 0x674), + MX53_PIN_SD1_DATA2 = _MXC_BUILD_GPIO_PIN(0, 19, 1, 0x2F0, 0x678), + MX53_PIN_SD1_CLK = _MXC_BUILD_GPIO_PIN(0, 20, 1, 0x2F4, 0x67C), + MX53_PIN_SD1_DATA3 = _MXC_BUILD_GPIO_PIN(0, 21, 1, 0x2F8, 0x680), + MX53_PIN_NVCC_SD1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x684), + MX53_PIN_SD2_CLK = _MXC_BUILD_GPIO_PIN(0, 10, 1, 0x2FC, 0x688), + MX53_PIN_SD2_CMD = _MXC_BUILD_GPIO_PIN(0, 11, 1, 0x300, 0x68C), + MX53_PIN_SD2_DATA3 = _MXC_BUILD_GPIO_PIN(0, 12, 1, 0x304, 0x690), + MX53_PIN_SD2_DATA2 = _MXC_BUILD_GPIO_PIN(0, 13, 1, 0x308, 0x694), + MX53_PIN_SD2_DATA1 = _MXC_BUILD_GPIO_PIN(0, 14, 1, 0x30C, 0x698), + MX53_PIN_SD2_DATA0 = _MXC_BUILD_GPIO_PIN(0, 15, 1, 0x310, 0x69C), + MX53_PIN_NVCC_SD2 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6A0), + MX53_PIN_GPIO_0 = _MXC_BUILD_GPIO_PIN(0, 0, 1, 0x314, 0x6A4), + MX53_PIN_GPIO_1 = _MXC_BUILD_GPIO_PIN(0, 1, 1, 0x318, 0x6A8), + MX53_PIN_GPIO_9 = _MXC_BUILD_GPIO_PIN(0, 9, 1, 0x31C, 0x6AC), + MX53_PIN_GPIO_3 = _MXC_BUILD_GPIO_PIN(0, 3, 1, 0x320, 0x6B0), + MX53_PIN_GPIO_6 = _MXC_BUILD_GPIO_PIN(0, 6, 1, 0x324, 0x6B4), + MX53_PIN_GPIO_2 = _MXC_BUILD_GPIO_PIN(0, 2, 1, 0x328, 0x6B8), + MX53_PIN_GPIO_4 = _MXC_BUILD_GPIO_PIN(0, 4, 1, 0x32C, 0x6BC), + MX53_PIN_GPIO_5 = _MXC_BUILD_GPIO_PIN(0, 5, 1, 0x330, 0x6C0), + MX53_PIN_GPIO_7 = _MXC_BUILD_GPIO_PIN(0, 7, 1, 0x334, 0x6C4), + MX53_PIN_GPIO_8 = _MXC_BUILD_GPIO_PIN(0, 8, 1, 0x338, 0x6C8), + MX53_PIN_GPIO_16 = _MXC_BUILD_GPIO_PIN(6, 11, 1, 0x33C, 0x6CC), + MX53_PIN_GPIO_17 = _MXC_BUILD_GPIO_PIN(6, 12, 1, 0x340, 0x6D0), + MX53_PIN_GPIO_18 = _MXC_BUILD_GPIO_PIN(6, 13, 1, 0x344, 0x6D4), + MX53_PIN_NVCC_GPIO = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6D8), + MX53_PIN_POR_B = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6DC), + MX53_PIN_BOOT_MODE1 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6E0), + MX53_PIN_RESET_IN_B = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6E4), + MX53_PIN_BOOT_MODE0 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6E8), + MX53_PIN_TEST_MODE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6EC), + MX53_PIN_GRP_ADDDS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6F0), + MX53_PIN_GRP_DDRMODE_CTL = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6F4), + MX53_PIN_GRP_DDRPKE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x6FC), + MX53_PIN_GRP_DDRPK = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x708), + MX53_PIN_GRP_TERM_CTL3 = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x70C), + MX53_PIN_GRP_DDRHYS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x710), + MX53_PIN_GRP_DDRMODE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x714), + MX53_PIN_GRP_B0DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x718), + MX53_PIN_GRP_B1DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x71C), + MX53_PIN_GRP_CTLDS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x720), + MX53_PIN_GRP_DDR_TYPE = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x724), + MX53_PIN_GRP_B2DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x728), + MX53_PIN_GRP_B3DS = _MXC_BUILD_NON_GPIO_PIN(NON_MUX_I, 0x72C), +}; +/* various IOMUX input select register index */ +typedef enum iomux_input_select { + MX51_AUDMUX_P4_INPUT_DA_AMX_SELECT_I = 0, + MX51_AUDMUX_P4_INPUT_DB_AMX_SELECT_I, + MX51_AUDMUX_P4_INPUT_TXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P4_INPUT_TXFS_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_DA_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_DB_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_RXFS_AMX_SELECT, + MX51_AUDMUX_P5_INPUT_TXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P5_INPUT_TXFS_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_DA_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_DB_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_RXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_RXFS_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_TXCLK_AMX_SELECT_INPUT, + MX51_AUDMUX_P6_INPUT_TXFS_AMX_SELECT_INPUT, + MX51_CCM_IPP_DI_CLK_SELECT_INPUT, + /* TO2 */ + MX51_CCM_IPP_DI1_CLK_SELECT_INPUT, + MX51_CCM_PLL1_BYPASS_CLK_SELECT_INPUT, + MX51_CCM_PLL2_BYPASS_CLK_SELECT_INPUT, + MX51_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX51_CSPI_IPP_IND_MISO_SELECT_INPUT, + MX51_CSPI_IPP_IND_MOSI_SELECT_INPUT, + MX51_CSPI_IPP_IND_SS_B_1_SELECT_INPUT, + MX51_CSPI_IPP_IND_SS_B_2_SELECT_INPUT, + MX51_CSPI_IPP_IND_SS_B_3_SELECT_INPUT, + MX51_DPLLIP1_L1T_TOG_EN_SELECT_INPUT, + /* TO2 */ + MX51_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT, + MX51_ECSPI2_IPP_IND_SS_B_3_SELECT_INPUT, + MX51_EMI_IPP_IND_RDY_INT_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT0_IN_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT1_IN_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT2_IN_SELECT_INPUT, + MX51_ESDHC3_IPP_DAT3_IN_SELECT_INPUT, + MX51_FEC_FEC_COL_SELECT_INPUT, + MX51_FEC_FEC_CRS_SELECT_INPUT, + MX51_FEC_FEC_MDI_SELECT_INPUT, + MX51_FEC_FEC_RDATA_0_SELECT_INPUT, + MX51_FEC_FEC_RDATA_1_SELECT_INPUT, + MX51_FEC_FEC_RDATA_2_SELECT_INPUT, + MX51_FEC_FEC_RDATA_3_SELECT_INPUT, + MX51_FEC_FEC_RX_CLK_SELECT_INPUT, + MX51_FEC_FEC_RX_DV_SELECT_INPUT, + MX51_FEC_FEC_RX_ER_SELECT_INPUT, + MX51_FEC_FEC_TX_CLK_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_1_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_2_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_3_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_5_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_6_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_7_SELECT_INPUT, + MX51_GPIO3_IPP_IND_G_IN_8_SELECT_INPUT, + /* TO2 */ + MX51_GPIO3_IPP_IND_G_IN_12_SELECT_INPUT, + MX51_HSC_MIPI_MIX_IPP_IND_SENS1_DATA_EN_SELECT_INPUT, + MX51_HSC_MIPI_MIX_IPP_IND_SENS2_DATA_EN_SELECT_INPUT, + /* TO2 */ + MX51_HSC_MIPI_MIX_PAR_VSYNC_SELECT_INPUT, + /* TO2 */ + MX51_HSC_MIPI_MIX_PAR_DI_WAIT_SELECT_INPUT, + MX51_HSC_MIPI_MIX_PAR_SISG_TRIG_SELECT_INPUT, + MX51_I2C1_IPP_SCL_IN_SELECT_INPUT, + MX51_I2C1_IPP_SDA_IN_SELECT_INPUT, + MX51_I2C2_IPP_SCL_IN_SELECT_INPUT, + MX51_I2C2_IPP_SDA_IN_SELECT_INPUT, + MX51_IPU_IPP_DI_0_IND_DISPB_SD_D_SELECT_INPUT, + MX51_IPU_IPP_DI_1_IND_DISPB_SD_D_SELECT_INPUT, + MX51_KPP_IPP_IND_COL_6_SELECT_INPUT, + MX51_KPP_IPP_IND_COL_7_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_4_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_5_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_6_SELECT_INPUT, + MX51_KPP_IPP_IND_ROW_7_SELECT_INPUT, + MX51_UART1_IPP_UART_RTS_B_SELECT_INPUT, + MX51_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, + MX51_UART2_IPP_UART_RTS_B_SELECT_INPUT, + MX51_UART2_IPP_UART_RXD_MUX_SELECT_INPUT, + MX51_UART3_IPP_UART_RTS_B_SELECT_INPUT, + MX51_UART3_IPP_UART_RXD_MUX_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_CLK_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_0_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_1_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_2_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_3_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_4_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_5_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_6_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DATA_7_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_DIR_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_NXT_SELECT_INPUT, + MX51_USBOH3_IPP_IND_UH3_STP_SELECT_INPUT, + MX51PUT_NUM_MUX, + /* MX53 */ + MX53_AUDMUX_P4_INPUT_DA_AMX_SELECT_I = 0, + MX53_AUDMUX_P4_INPUT_DB_AMX_SELECT_I, + MX53_AUDMUX_P4_INPUT_RXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P4_INPUT_RXFS_AMX_SELECT_INPUT, + MX53_AUDMUX_P4_INPUT_TXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P4_INPUT_TXFS_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_DA_AMX_SELECT_I, + MX53_AUDMUX_P5_INPUT_DB_AMX_SELECT_I, + MX53_AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_RXFS_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_TXCLK_AMX_SELECT_INPUT, + MX53_AUDMUX_P5_INPUT_TXFS_AMX_SELECT_INPUT, + MX53_CAN1_IPP_IND_CANRX_SELECT_INPUT, + MX53_CAN2_IPP_IND_CANRX_SELECT_INPUT, + MX53_CCM_IPP_ASRC_EXT_SELECT_INPUT, + MX53_CCM_IPP_DI1_CLK_SELECT_INPUT, + MX53_CCM_PLL1_BYPASS_CLK_SELECT_INPUT, + MX53_CCM_PLL2_BYPASS_CLK_SELECT_INPUT, + MX53_CCM_PLL3_BYPASS_CLK_SELECT_INPUT, + MX53_CCM_PLL4_BYPASS_CLK_SELECT_INPUT, + MX53_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX53_CSPI_IPP_IND_MISO_SELECT_INPUT, + MX53_CSPI_IPP_IND_MOSI_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_1_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_2_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_3_SELECT_INPUT, + MX53_CSPI_IPP_IND_SS_B_4_SELECT_INPUT, + MX53_ECSPI1_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_MISO_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_MOSI_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_1_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_2_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_3_SELECT_INPUT, + MX53_ECSPI1_IPP_IND_SS_B_4_SELECT_INPUT, + MX53_ECSPI2_IPP_CSPI_CLK_IN_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_MISO_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_MOSI_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT, + MX53_ECSPI2_IPP_IND_SS_B_2_SELECT_INPUT, + MX53_ESAI1_IPP_IND_FSR_SELECT_INPUT, + MX53_ESAI1_IPP_IND_FST_SELECT_INPUT, + MX53_ESAI1_IPP_IND_HCKR_SELECT_INPUT, + MX53_ESAI1_IPP_IND_HCKT_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SCKR_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SCKT_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO0_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO1_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO2_SDI3_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO3_SDI2_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO4_SDI1_SELECT_INPUT, + MX53_ESAI1_IPP_IND_SDO5_SDI0_SELECT_INPUT, + MX53_ESDHC1_IPP_WP_ON_SELECT_INPUT, + MX53_FEC_FEC_COL_SELECT_INPUT, + MX53_FEC_FEC_MDI_SELECT_INPUT, + MX53_FEC_FEC_RX_CLK_SELECT_INPUT, + MX53_FIRI_IPP_IND_RXD_SELECT_INPUT, + MX53_GPC_PMIC_RDY_SELECT_INPUT, + MX53_I2C1_IPP_SCL_IN_SELECT_INPUT, + MX53_I2C1_IPP_SDA_IN_SELECT_INPUT, + MX53_I2C2_IPP_SCL_IN_SELECT_INPUT, + MX53_I2C2_IPP_SDA_IN_SELECT_INPUT, + MX53_I2C3_IPP_SCL_IN_SELECT_INPUT, + MX53_I2C3_IPP_SDA_IN_SELECT_INPUT, + MX53_IPU_IPP_DI_0_IND_DISPB_SD_D_SELECT_INPUT, + MX53_IPU_IPP_DI_1_IND_DISPB_SD_D_SELECT_INPUT, + MX53_IPU_IPP_IND_SENS1_DATA_EN_SELECT_INPUT, + MX53_IPU_IPP_IND_SENS1_HSYNC_SELECT_INPUT, + MX53_IPU_IPP_IND_SENS1_VSYNC_SELECT_INPUT, + MX53_KPP_IPP_IND_COL_5_SELECT_INPUT, + MX53_KPP_IPP_IND_COL_6_SELECT_INPUT, + MX53_KPP_IPP_IND_COL_7_SELECT_INPUT, + MX53_KPP_IPP_IND_ROW_5_SELECT_INPUT, + MX53_KPP_IPP_IND_ROW_6_SELECT_INPUT, + MX53_KPP_IPP_IND_ROW_7_SELECT_INPUT, + MX53_MLB_MLBCLK_IN_SELECT_INPUT, + MX53_MLB_MLBDAT_IN_SELECT_INPUT, + MX53_MLB_MLBSIG_IN_SELECT_INPUT, + MX53_OWIRE_BATTERY_LINE_IN_SELECT_INPUT, + MX53_SDMA_EVENTS_14_SELECT_INPUT, + MX53_SDMA_EVENTS_15_SELECT_INPUT, + MX53_SPDIF_SPDIF_IN1_SELECT_INPUT, + MX53_UART1_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART2_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART2_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART3_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART3_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART4_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART4_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_UART5_IPP_UART_RTS_B_SELECT_INPUT, + MX53_UART5_IPP_UART_RXD_MUX_SELECT_INPUT, + MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, + MX53_USBOH3_IPP_IND_UH1_OC_SELECT_INPUT, + MX53_USBOH3_IPP_IND_UH2_OC_SELECT_INPUT, +} iomux_input_select_t; + #endif /* __ASSEMBLY__ */ #endif /* __ASM_ARCH_MX5_MX5X_PINS_H__ */ diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h old mode 100644 new mode 100755 index b4e5738..3d6d390 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -24,8 +24,6 @@ #ifndef __CONFIG_H #define __CONFIG_H -#include <asm/arch/imx-regs.h> - /* High Level Configuration Options */ #define CONFIG_MX51 /* in a mx51 */ @@ -37,6 +35,7 @@ #define CONFIG_L2_OFF +#include <asm/arch/imx-regs.h> /* * Disabled for now due to build problems under Debian and a significant * increase in the final file size: 144260 vs. 109536 Bytes. diff --git a/include/configs/vision2.h b/include/configs/vision2.h index a5c116b..4c8e7fa 100644 --- a/include/configs/vision2.h +++ b/include/configs/vision2.h @@ -24,11 +24,12 @@ #ifndef __CONFIG_H #define __CONFIG_H -#include <asm/arch/imx-regs.h> #define CONFIG_MX51 /* in a mx51 */ #define CONFIG_L2_OFF +#include <asm/arch/imx-regs.h> + #define CONFIG_SYS_MX5_HCLK 24000000 #define CONFIG_SYS_MX5_CLK32 32768 #define CONFIG_DISPLAY_CPUINFO -- 1.7.0.4

8 33

[U-Boot] [PATCH 0/1] mmc: S5P: Support DMA restarts at buffer boundaries
by Anton Staaf 13 Jul '11

13 Jul '11

I don't actually have an S5P machine to test this patch with. I wrote this code while fixing an issue with the in progress Tegra MMC device driver that is based on the S5P driver. I have tested this patch on that platform. If someone with an S5P could give this a whirl that would be great. Cc: Minkyu Kang <mk7.kang(a)samsung.com> Cc: Jaehoon Chung <jh80.chung(a)samsung.com> Cc: Albert ARIBAUD <albert.u.boot(a)aribaud.net> Anton Staaf (1): mmc: S5P: Support DMA restarts at buffer boundaries drivers/mmc/s5p_mmc.c | 15 +++++++++++---- 1 files changed, 11 insertions(+), 4 deletions(-) -- 1.7.3.1

3 3

[U-Boot] [PATCH] tools: build some commands without -pedantic
by Linus Walleij 13 Jul '11

13 Jul '11

On this GCC in Fedora (4.6.0 20110530) the tools gen_eth_addr and img2srec become size zero if compiled with -pedantic (no warnings are emitted however). Marking them _NOPED solves the issue for me. Signed-off-by: Linus Walleij <linus.walleij(a)linaro.org> --- tools/Makefile | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-) diff --git a/tools/Makefile b/tools/Makefile index 97f83f8..cc7bc69 100644 --- a/tools/Makefile +++ b/tools/Makefile @@ -83,8 +83,8 @@ OBJ_FILES-$(CONFIG_VIDEO_LOGO) += bmp_logo.o NOPED_OBJ_FILES-y += default_image.o OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o NOPED_OBJ_FILES-y += fit_image.o -OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o -OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o +NOPED_OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o +NOPED_OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o OBJ_FILES-$(CONFIG_INCA_IP) += inca-swap-bytes.o NOPED_OBJ_FILES-y += kwbimage.o NOPED_OBJ_FILES-y += imximage.o @@ -168,7 +168,7 @@ $(obj)envcrc$(SFX): $(obj)crc32.o $(obj)env_embedded.o $(obj)envcrc.o $(obj)sha1 $(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^ $(obj)gen_eth_addr$(SFX): $(obj)gen_eth_addr.o - $(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^ + $(HOSTCC) $(HOSTCFLAGS_NOPED) $(HOSTLDFLAGS) -o $@ $^ $(HOSTSTRIP) $@ $(obj)img2srec$(SFX): $(obj)img2srec.o -- 1.7.6

3 11

[U-Boot] General gpio interface?
by Simon Schwarz 12 Jul '11

12 Jul '11

Hi List, am I right that there is no standard gpio interface in u-boot or did I miss it? Regards Simon

2 1

[U-Boot] [PATCH v3] scb9328: Add ARM relocation support
by Torsten Koschorrek 12 Jul '11

12 Jul '11

This patch fixes compiler errors due to missing definitions of CONFIG_SYS_SDRAM_BASE and CONFIG_SYS_INIT_SP_ADDR. It also does some cleanup: CONFIG_SYS_TEXT_BASE was moved to scb9328.h, obsolete config.mk was removed. The scb9328 board has 1 DRAM bank, so don't ask for more banks. CONFIG_NR_DRAM_BANKS will ever be 1. Signed-off-by: Torsten Koschorrek <koschorrek(a)synertronixx.de> --- Changes for v2: - config.mk removed - cleanups in dram_init_banksize() Changes for v3: - checkpatch errors fixed board/scb9328/config.mk | 10 ---------- board/scb9328/scb9328.c | 24 +++++++++--------------- include/configs/scb9328.h | 5 +++++ 3 files changed, 14 insertions(+), 25 deletions(-) delete mode 100644 board/scb9328/config.mk diff --git a/board/scb9328/config.mk b/board/scb9328/config.mk deleted file mode 100644 index 7c5e067..0000000 --- a/board/scb9328/config.mk +++ /dev/null @@ -1,10 +0,0 @@ -# -# This config file is used for compilation of scb93328 sources -# -# You might change location of U-Boot in memory by setting right CONFIG_SYS_TEXT_BASE. -# This allows for example having one copy located at the end of ram and stored -# in flash device and later on while developing use other location to test -# the code in RAM device only. -# - -CONFIG_SYS_TEXT_BASE = 0x08f00000 diff --git a/board/scb9328/scb9328.c b/board/scb9328/scb9328.c index 428e8c9..2e31e8c 100644 --- a/board/scb9328/scb9328.c +++ b/board/scb9328/scb9328.c @@ -39,23 +39,17 @@ int board_init (void) int dram_init (void) { -#if ( CONFIG_NR_DRAM_BANKS > 0 ) + /* dram_init must store complete ramsize in gd->ram_size */ + gd->ram_size = get_ram_size((volatile void *)SCB9328_SDRAM_1, + SCB9328_SDRAM_1_SIZE); + + return 0; +} + +void dram_init_banksize(void) +{ gd->bd->bi_dram[0].start = SCB9328_SDRAM_1; gd->bd->bi_dram[0].size = SCB9328_SDRAM_1_SIZE; -#endif -#if ( CONFIG_NR_DRAM_BANKS > 1 ) - gd->bd->bi_dram[1].start = SCB9328_SDRAM_2; - gd->bd->bi_dram[1].size = SCB9328_SDRAM_2_SIZE; -#endif -#if ( CONFIG_NR_DRAM_BANKS > 2 ) - gd->bd->bi_dram[2].start = SCB9328_SDRAM_3; - gd->bd->bi_dram[2].size = SCB9328_SDRAM_3_SIZE; -#endif -#if ( CONFIG_NR_DRAM_BANKS > 3 ) - gd->bd->bi_dram[3].start = SCB9328_SDRAM_4; - gd->bd->bi_dram[3].size = SCB9328_SDRAM_4_SIZE; -#endif - return 0; } /** diff --git a/include/configs/scb9328.h b/include/configs/scb9328.h index 6a92ec3..1b5d931 100644 --- a/include/configs/scb9328.h +++ b/include/configs/scb9328.h @@ -126,6 +126,11 @@ #define SCB9328_SDRAM_1 0x08000000 /* SDRAM bank #1 */ #define SCB9328_SDRAM_1_SIZE 0x01000000 /* 16 MB */ +#define CONFIG_SYS_TEXT_BASE 0x10000000 + +#define CONFIG_SYS_SDRAM_BASE SCB9328_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (SCB9328_SDRAM_1 + 0xf00000) + /* * Configuration for FLASH memory for the Synertronixx board */ -- 1.7.5.4

2 1

[U-Boot] Dear Sir / Madam Please read.
by Mr Kuwaiti Zuweiri 12 Jul '11

12 Jul '11

Dear Sir / Madam Please read. It is my sincere pleasure at this moment to exhibit my total trust bestowed on you in accordance to my Proposed partnership relationship with you of which I am fully convinced that you will really welcome my partnership with you in this transaction Being very sceptical about dealing with Africans in such transaction, Ranging from the height of fraudulent activities encompassing the African communities. Now it is my Godly nursed intention to prove myself to you that I am very much different from others which you must have come across. I hereby attested my accepted conclusion to take upon my gentle self and to join hands together to cover any unforeseen expenses that may be involved here till the Final Transfer of the Funds to our Correspondent Bank before its Final remittance into your Nominated Bank Account. This is to convince you of my spirited acceptance to have you as a confidant in a business of this magnitude knowing that you will not turn me down come-what-may, regarding this Claim/Transfer to boost my planned establishment of a funding Company out of Africa . In other Words, I went into a more concrete arrangement in couriering to your doorstep, a total of US$10.5Million Dollars through INTER-BANK TRANSFER. This amount of Money belongs to our Deceased Customer as there were no claims over this Dormant Balance Account for a period of many Years. Therefore, I am in need of a Reliable Partner that would come forward to put claims over the Funds for its Transfer into his/her Foreign Bank Account. This is because I am the Director of Foreign Remittance Department of my Bank for secures Transfer of these Funds without any Hindrances. All I am expecting from you, as a matter of greatest urgency and importance is your sincerity and Honesty as I have some of the Needed Legal Documents to prove that this Business is Lawful for its onward Remittance.I urgently want you to send all the demanded Personal Information’s below to me as soon as you receive this PROPOSAL in order to show your readiness and Willingness in this Proposed Business. BELOW ARE THE NEEDED PERSONAL INFORMATIONS 1) Your Full Name.......................... ...2) Your Age........................... ............3) Your Mobile and Home Phone Number…………..4) Your Fax Number………………..... 5) Your Country of Nationality………………............. .6) Your Occupation.................... ........7) Sex........................... .....................8) Alternative E-mail Address/ ........................ Finally, you have to keep this Proposal confidential and secret from your Relations, Partners and Colleagues for our success in this Transaction as the basis of this Business is Secrecy. I promise you that I would protect your Personal Interest as this Business is 100 risk-free. Therefore, I want you to express your interest to engage in this Business with me because your share is 40% of the Funds in Question so that I can send to you the TEXT OF APPLICATION which you have to Fill and send to the E-mail Address of the Bank. I look forward for your immediate Positive response. My regards to you and the family, Mr Kuwaiti Zuweiri

1 0

[U-Boot] Message from Miss Rosalinda Banah to you
by Rosalinda Banah 12 Jul '11

12 Jul '11

Message from Miss Rosalinda Banah to you With due respect, I send my sincere greetings to you. My name is Miss Rosalinda Banah, 17 yrs old, an Ivorian from western city of San Pedro. I am presently taking refuge in Ghana because of the political crisis that is going on in our country presently. My father was an Agricultural contractor, a cocoa beans exporter and a staunch member of FPI party (Laurent Gbagbo’s party) in San Pedro. My father was assassination along side with my elder brother by pro-Ouattara rebels, in the night they took the Port of San Pedro. I escaped the massacre with my little sister 9yrs old, but unfortunately, she was hit by stray bullet on our route of escape and she died instantly. I am now left without parents, brother and the most painful, my little sister whom I love so much. Please, my reason of contacting you is that I need your urgent help to resettle my shattered life in your country. I want to let you know that there is this fund, Eight million United States dollars ($8,000,000.00) which is left in a suspense account of my late father in a bank outside our country, where he normally receives payment of his cocoa exports. This is the only money I can lay my hands on, to continue my education and face my future avenue. Please, I am seeking your help to transfer and secure this money for investment purposes in your country. It is my wish to come over to your country to live with you and continue my studies. I also want you to help me to invest this money for me in a profitable business venture in your country, because I do not know about business, as I am only a student. I am willing from my heart to compensate you with 30% of the total amount, if you would sincerely assist me. I will give you details about this fund, as soon as I get your positive response. Please, if you find this mail offensive, please ignore it and accept my apology. Best regards, Miss Rosalinda Banah

1 0

[U-Boot] [PATCH 4/4] integrator: support some rudimentary commands
by Linus Walleij 12 Jul '11

12 Jul '11

This adds support for a subset of the default commands for the Integrator, however since the card does not have Ethernet (unless you plug in a PCI card) we can not use the default command set. Signed-off-by: Linus Walleij <linus.walleij(a)linaro.org> --- include/configs/integratorap.h | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-) diff --git a/include/configs/integratorap.h b/include/configs/integratorap.h index ea6af78..26eac8b 100644 --- a/include/configs/integratorap.h +++ b/include/configs/integratorap.h @@ -81,9 +81,15 @@ * Command line configuration. */ + #define CONFIG_CMD_IMI #define CONFIG_CMD_BDI +#define CONFIG_CMD_BOOTD #define CONFIG_CMD_MEMORY +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_IMLS +#define CONFIG_CMD_LOADB +#define CONFIG_CMD_LOADS #define CONFIG_BOOTDELAY 2 -- 1.7.6

1 0

[U-Boot] [PATCH 3/4] integrator: support the hush shell
by Linus Walleij 12 Jul '11

12 Jul '11

Give us some kind of sane shell environment so the bootloader can be used. Signed-off-by: Linus Walleij <linus.walleij(a)linaro.org> --- include/configs/integratorap.h | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/include/configs/integratorap.h b/include/configs/integratorap.h index 8b41885..ea6af78 100644 --- a/include/configs/integratorap.h +++ b/include/configs/integratorap.h @@ -94,7 +94,9 @@ * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT "Integrator-AP # " /* Monitor Command Prompt */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "# " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -- 1.7.6

1 0

[U-Boot] [PATCH 2/4] integratorap: support relocation
by Linus Walleij 12 Jul '11

12 Jul '11

The integrator board was apparently never converted over to support relocation until now. After this the integrator u-boot both compiles and boots on the Integrator AP. Signed-off-by: Linus Walleij <linus.walleij(a)linaro.org> --- board/armltd/integrator/integrator.c | 14 ++++++++------ 1 files changed, 8 insertions(+), 6 deletions(-) diff --git a/board/armltd/integrator/integrator.c b/board/armltd/integrator/integrator.c index 9bb56b5..a0d8de7 100644 --- a/board/armltd/integrator/integrator.c +++ b/board/armltd/integrator/integrator.c @@ -86,14 +86,16 @@ int misc_init_r (void) return (0); } -/****************************** - Routine: - Description: -******************************/ -int dram_init (void) +void dram_init_banksize(void) { gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; +} + +int dram_init (void) +{ + gd->ram_size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, + PHYS_SDRAM_1_SIZE); #ifdef CONFIG_CM_SPD_DETECT { -- 1.7.6

1 0