November 2010 - U-Boot

[U-Boot] [PATCH 1/3] arm926ejs: fix linker file for newer ld support
by Albert Aribaud 02 Nov '10

02 Nov '10

older ld emitted all ELF relocations in input sections named .rel.dyn, whereas newer ld uses names of the form .rel*. The linker script only collected .rel.dyn input sections. Fit it to collect all .rel* input sections. Signed-off-by: Albert Aribaud <albert.aribaud(a)free.fr> --- arch/arm/cpu/arm926ejs/u-boot.lds | 18 +++++++++--------- 1 files changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm/cpu/arm926ejs/u-boot.lds b/arch/arm/cpu/arm926ejs/u-boot.lds index 72f45f8..4e42543 100644 --- a/arch/arm/cpu/arm926ejs/u-boot.lds +++ b/arch/arm/cpu/arm926ejs/u-boot.lds @@ -45,15 +45,6 @@ SECTIONS . = ALIGN(4); - __rel_dyn_start = .; - .rel.dyn : { *(.rel.dyn) } - __rel_dyn_end = .; - - __dynsym_start = .; - .dynsym : { *(.dynsym) } - - . = ALIGN(4); - . = .; __u_boot_cmd_start = .; .u_boot_cmd : { *(.u_boot_cmd) } @@ -64,6 +55,15 @@ SECTIONS .bss (NOLOAD) : { *(.bss) . = ALIGN(4); } _end = .; + __rel_dyn_start = .; + .rel.dyn : { *(.rel*) } + __rel_dyn_end = .; + + __dynsym_start = .; + .dynsym : { *(.dynsym) } + + . = ALIGN(4); + /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynamic*) } /DISCARD/ : { *(.plt*) } -- 1.7.1

4 6

[U-Boot] Congratulations - Promo Winner
by MICROSOFT EMAIL PROMOTION 02 Nov '10

02 Nov '10

Congratulations - Promo Winner The MICROSOFT EMAIL PROMO TEAM is glad to announce that after a successful completion of the PROMO DRAWS held on the 1st November 2010, your e-mail address,attached to winning numbers:(11) (80) (12)(96) (09) (43) won in the Tenth lottery category. You have therefore been approved to claim a total sum of £450,000,00 Pounds Sterling in cash credited to REF NO:MICRO-L/2009-END10. All participants were selected through our Microsoft computer ballot system drawn from 167,000 Names,as part of our International "E-MAIL" Promotion Program for our prominent MS-WORD users all over the world and for the continuous use of the internet. You are advised to contact the claims processor with the details below via his e-mail address : NAME: Glenn Bradley EMAIL: mrglenn_bradley01(a)yahoo.com.hk PLEASE NOTE YOU ARE TO SEND THE FOLLOWING INFORMATION TO CLAIM YOUR PRIZE: 1.Full Name:... 2.Address:... 3.Phone:... 4.Country:... 5.Sex/Gender:... YOURS SINCERELY, RACHEL STEWART.

1 0

[U-Boot] Add video support for mx51evk
by Frias Renato-B13784 02 Nov '10

02 Nov '10

Hello Stefano, This is my first post to the list, I work as Field Engineer for Freescale, based in Brazil. I'll be submitting couple patches to add support for the wvga lcd on the mx51evk board, these are based on the work you did for vision2 board. However, in order to add support for the second display inteface on the imx51, I had to change the Framebuffer driver. Thus, support for vision2 will break, to restore it all is needed is to add couple arguments to mx51_fb_init call. Please review the patches and let me know if I should have done things in a different way. There is also a second issue where I would like to know your thoughts. Very early on system initialization, when LCD is enabled, there is a call to "lcd_setmem" from board.c. By that time, the video variables, "panel_info", are not set yet. Thus U-Boot doesn't reserve the appropriate amount of memory for the display. I was going to set "panel_info" variable on mx51evk.c, but I would like to know how you solved it for vision2 first. Thanks! Renato Frias

1 0

[U-Boot] Congratulations - Promo Winner
by MICROSOFT EMAIL PROMOTION 02 Nov '10

02 Nov '10

Congratulations - Promo Winner The MICROSOFT EMAIL PROMO TEAM is glad to announce that after a successful completion of the PROMO DRAWS held on the 1st November 2010, your e-mail address,attached to winning numbers:(11) (80) (12)(96) (09) (43) won in the Tenth lottery category. You have therefore been approved to claim a total sum of £450,000,00 Pounds Sterling in cash credited to REF NO:MICRO-L/2009-END10. All participants were selected through our Microsoft computer ballot system drawn from 167,000 Names,as part of our International "E-MAIL" Promotion Program for our prominent MS-WORD users all over the world and for the continuous use of the internet. You are advised to contact the claims processor with the details below via his e-mail address : NAME: Glenn Bradley EMAIL: mrglennbradley01(a)yahoo.com.hk PLEASE NOTE YOU ARE TO SEND THE FOLLOWING INFORMATION TO CLAIM YOUR PRIZE: 1.Full Name:... 2.Address:... 3.Phone:... 4.Country:... 5.Sex/Gender:... YOURS SINCERELY, RACHEL STEWART.

1 0

[U-Boot] [PATCH v2] mmc: omap: timeout counter fix
by Nishanth Menon 01 Nov '10

01 Nov '10

Having a loop with a counter is no timing guarentee for timing accuracy or compiler optimizations. For e.g. the same loop counter which runs when the MPU is running at 600MHz will timeout in around half the time when running at 1GHz. or the example where GCC 4.5 compiles with different optimization compared to GCC 4.4. use a udelay(10) to ensure we have a predictable delay. use an emperical number - 100000 uSec ~= 1sec for a worst case timeout. This should never happen, and is adequate imaginary condition for us to fail with timeout. Signed-off-by: Nishanth Menon <nm(a)ti.com> --- V2: additional cleanups + made MAX_RETRY a macro for reuse throughout the file. tested on PandaBoard with 1GHz boot frequency and GCC4.5 on u-boot 2010.09 + mmc patches. Requesting testing on other platforms V1: http://www.mail-archive.com/u-boot@lists.denx.de/msg40969.html drivers/mmc/omap_hsmmc.c | 114 +++++++++++++++++++++++++++++++++++++++------- 1 files changed, 97 insertions(+), 17 deletions(-) diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index 9271470..f7bdfe9 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -30,6 +30,7 @@ #include <twl4030.h> #include <asm/io.h> #include <asm/arch/mmc_host_def.h> +#define MAX_RETRY 100000 static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size); static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int siz); @@ -70,18 +71,32 @@ unsigned char mmc_board_init(hsmmc_t *mmc_base) void mmc_init_stream(hsmmc_t *mmc_base) { + int retry = MAX_RETRY; writel(readl(&mmc_base->con) | INIT_INITSTREAM, &mmc_base->con); writel(MMC_CMD0, &mmc_base->cmd); - while (!(readl(&mmc_base->stat) & CC_MASK)) - ; + while (!(readl(&mmc_base->stat) & CC_MASK)) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for cc!\n", __func__); + return; + } + } writel(CC_MASK, &mmc_base->stat) ; writel(MMC_CMD0, &mmc_base->cmd) ; - while (!(readl(&mmc_base->stat) & CC_MASK)) - ; + retry = MAX_RETRY; + while (!(readl(&mmc_base->stat) & CC_MASK)) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for cc2!\n", __func__); + return; + } + } writel(readl(&mmc_base->con) & ~INIT_INITSTREAM, &mmc_base->con); } @@ -91,16 +106,31 @@ static int mmc_init_setup(struct mmc *mmc) hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv; unsigned int reg_val; unsigned int dsor; + int retry = MAX_RETRY; mmc_board_init(mmc_base); writel(readl(&mmc_base->sysconfig) | MMC_SOFTRESET, &mmc_base->sysconfig); - while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0) - ; + while ((readl(&mmc_base->sysstatus) & RESETDONE) == 0) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for cc2!\n", __func__); + return TIMEOUT; + } + } writel(readl(&mmc_base->sysctl) | SOFTRESETALL, &mmc_base->sysctl); - while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0) - ; + retry = MAX_RETRY; + while ((readl(&mmc_base->sysctl) & SOFTRESETALL) != 0x0) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for softresetall!\n", + __func__); + return TIMEOUT; + } + } writel(DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0, &mmc_base->hctl); writel(readl(&mmc_base->capa) | VS30_3V0SUP | VS18_1V8SUP, &mmc_base->capa); @@ -116,8 +146,15 @@ static int mmc_init_setup(struct mmc *mmc) (ICE_STOP | DTO_15THDTO | CEN_DISABLE)); mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK, (dsor << CLKD_OFFSET) | ICE_OSCILLATE); - while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) - ; + retry = MAX_RETRY; + while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for ics!\n", __func__); + return TIMEOUT; + } + } writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl); writel(readl(&mmc_base->hctl) | SDBP_PWRON, &mmc_base->hctl); @@ -137,14 +174,27 @@ static int mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, { hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv; unsigned int flags, mmc_stat; - unsigned int retry = 0x100000; + int retry = MAX_RETRY; - while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS) - ; + while ((readl(&mmc_base->pstate) & DATI_MASK) == DATI_CMDDIS) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for cmddis!\n", __func__); + return TIMEOUT; + } + } writel(0xFFFFFFFF, &mmc_base->stat); - while (readl(&mmc_base->stat)) - ; + retry = MAX_RETRY; + while (readl(&mmc_base->stat)) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for stat!\n", __func__); + return TIMEOUT; + } + } /* * CMDREG * CMDIDX[13:8] : Command index @@ -200,8 +250,11 @@ static int mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, writel(cmd->cmdarg, &mmc_base->arg); writel((cmd->cmdidx << 24) | flags, &mmc_base->cmd); + retry = MAX_RETRY; do { mmc_stat = readl(&mmc_base->stat); + if (!mmc_stat) + udelay(10); retry--; } while ((mmc_stat == 0) && (retry > 0)); @@ -253,8 +306,18 @@ static int mmc_read_data(hsmmc_t *mmc_base, char *buf, unsigned int size) count /= 4; while (size) { + int retry = MAX_RETRY; do { mmc_stat = readl(&mmc_base->stat); + if (!mmc_stat) { + retry--; + udelay(10); + } + if (!retry) { + printf("%s: timedout waiting for status!\n", + __func__); + return TIMEOUT; + } } while (mmc_stat == 0); if ((mmc_stat & ERRI_MASK) != 0) @@ -298,8 +361,18 @@ static int mmc_write_data(hsmmc_t *mmc_base, const char *buf, unsigned int size) count /= 4; while (size) { + int retry = MAX_RETRY; do { mmc_stat = readl(&mmc_base->stat); + if (!mmc_stat) { + retry--; + udelay(10); + } + if (!retry) { + printf("%s: timedout waiting for status!\n", + __func__); + return TIMEOUT; + } } while (mmc_stat == 0); if ((mmc_stat & ERRI_MASK) != 0) @@ -334,6 +407,7 @@ static void mmc_set_ios(struct mmc *mmc) { hsmmc_t *mmc_base = (hsmmc_t *)mmc->priv; unsigned int dsor = 0; + int retry = MAX_RETRY; /* configue bus width */ switch (mmc->bus_width) { @@ -372,8 +446,14 @@ static void mmc_set_ios(struct mmc *mmc) mmc_reg_out(&mmc_base->sysctl, ICE_MASK | CLKD_MASK, (dsor << CLKD_OFFSET) | ICE_OSCILLATE); - while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) - ; + while ((readl(&mmc_base->sysctl) & ICS_MASK) == ICS_NOTREADY) { + retry--; + udelay(10); + if (!retry) { + printf("%s: timedout waiting for ics!\n", __func__); + return; + } + } writel(readl(&mmc_base->sysctl) | CEN_ENABLE, &mmc_base->sysctl); } -- 1.6.3.3

5 31

[U-Boot] [PATCH 2/3 V5] Remove board_init_f function from nand_boot.c
by Sughosh Ganu 01 Nov '10

01 Nov '10

Remove the board_init_f function from nand_spl/nand_boot.c. This function is to be defined by all boards using the nand_spl functionality in their individual board directory. Currently this function was being used by the smdk6400 board. Added the board specific function definition. Signed-off-by: Sughosh Ganu <urwithsughosh(a)gmail.com> Acked-by: Scott Wood <scottwood(a)freescale.com> --- Changes since V4: * Modified the subject line to indicate the correct function name being deleted * Updated w.r.t mainline tot. board/samsung/smdk6400/smdk6400_nand_spl.c | 37 ++++++++++++++++++++++++++++ nand_spl/board/samsung/smdk6400/Makefile | 6 ++++- nand_spl/nand_boot.c | 8 ------ 3 files changed, 42 insertions(+), 9 deletions(-) create mode 100644 board/samsung/smdk6400/smdk6400_nand_spl.c diff --git a/board/samsung/smdk6400/smdk6400_nand_spl.c b/board/samsung/smdk6400/smdk6400_nand_spl.c new file mode 100644 index 0000000..a023284 --- /dev/null +++ b/board/samsung/smdk6400/smdk6400_nand_spl.c @@ -0,0 +1,37 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger(a)sysgo.de> + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, <d.mueller(a)elsoft.ch> + * + * (C) Copyright 2008 + * Guennadi Liakhovetki, DENX Software Engineering, <lg(a)denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +void board_init_f(unsigned long bootflag) +{ + relocate_code(CONFIG_SYS_TEXT_BASE - TOTAL_MALLOC_LEN, NULL, + CONFIG_SYS_TEXT_BASE); +} diff --git a/nand_spl/board/samsung/smdk6400/Makefile b/nand_spl/board/samsung/smdk6400/Makefile index 2111e57..18cee10 100644 --- a/nand_spl/board/samsung/smdk6400/Makefile +++ b/nand_spl/board/samsung/smdk6400/Makefile @@ -35,7 +35,7 @@ AFLAGS += -DCONFIG_NAND_SPL CFLAGS += -DCONFIG_NAND_SPL SOBJS = start.o cpu_init.o lowlevel_init.o -COBJS = nand_boot.o nand_ecc.o s3c64xx.o +COBJS = nand_boot.o nand_ecc.o s3c64xx.o smdk6400_nand_spl.o SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) @@ -93,6 +93,10 @@ $(obj)s3c64xx.c: @rm -f $@ @ln -s $(TOPDIR)/drivers/mtd/nand/s3c64xx.c $@ +$(obj)smdk6400_nand_spl.c: + @rm -f $@ + @ln -s $(TOPDIR)/board/samsung/smdk6400/smdk6400_nand_spl.c $@ + ######################################################################### $(obj)%.o: $(obj)%.S diff --git a/nand_spl/nand_boot.c b/nand_spl/nand_boot.c index d624418..b9fd6f5 100644 --- a/nand_spl/nand_boot.c +++ b/nand_spl/nand_boot.c @@ -221,14 +221,6 @@ static int nand_load(struct mtd_info *mtd, unsigned int offs, return 0; } -#if defined(CONFIG_ARM) -void board_init_f (ulong bootflag) -{ - relocate_code (CONFIG_SYS_TEXT_BASE - TOTAL_MALLOC_LEN, NULL, - CONFIG_SYS_TEXT_BASE); -} -#endif - /* * The main entry for NAND booting. It's necessary that SDRAM is already * configured and available since this code loads the main U-Boot image -- 1.7.0.4

4 4

[U-Boot] [PATCH 3/3 V5] Add board support for hawkboard
by Sughosh Ganu 01 Nov '10

01 Nov '10

The patch adds basic board support for TI's OMAP-L138 based Hawkboard. This board is pretty similar to the da850 EVM. Support for nand and network access is added in this version. The following bootup procedure is used. At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand controllers and copies the second stage bootloader(nand_spl) to RAM. The secondary bootloader then copies u-boot from a predefined location in the nand flash to the RAM, and passes control to the u-boot image. Three config options are supported * hawkboard_config - Used to create the u-boot.bin. Tftp the u-boot.bin image to the RAM from u-boot, and flash to the nand flash at address 0xe0000. * hawkboard_nand_config - Used to generate the secondary bootloader(nand_spl) image. This creates an elf file u-boot-spl under nand_spl/. Create an AIS signed image using this file, and flash it to the nand flash at address 0x20000. The ais file should fit in one block. * hawkboard_uart_config - This is same as the first image, but with the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS Signed bin, as use the normal UART boot procedure to boot the image. Signed-off-by: Sughosh Ganu <urwithsughosh(a)gmail.com> --- Changes since V4 * Replaced CONFIG_SYS_GBL_DATA_SIZE with GENERATED_GBL_DATA_SIZE * Removed the superfluous call to relocate_code in nand_spl MAINTAINERS | 5 + arch/arm/include/asm/arch-davinci/da8xx_common.h | 3 + arch/arm/include/asm/arch-davinci/hardware.h | 5 +- board/davinci/common/Makefile | 2 +- board/davinci/common/davinci_pinmux.c | 105 +++++++++++ board/davinci/common/misc.c | 75 -------- board/davinci/da8xxevm/Makefile | 1 + board/davinci/da8xxevm/hawkboard.c | 69 ++++++++ board/davinci/da8xxevm/hawkboard_nand_spl.c | 158 +++++++++++++++++ boards.cfg | 3 + doc/README.hawkboard | 93 ++++++++++ include/configs/hawkboard.h | 200 ++++++++++++++++++++++ nand_spl/board/davinci/da8xxevm/Makefile | 141 +++++++++++++++ nand_spl/board/davinci/da8xxevm/u-boot.lds | 75 ++++++++ nand_spl/nand_boot.c | 1 + 15 files changed, 859 insertions(+), 77 deletions(-) create mode 100644 board/davinci/common/davinci_pinmux.c create mode 100644 board/davinci/da8xxevm/hawkboard.c create mode 100644 board/davinci/da8xxevm/hawkboard_nand_spl.c create mode 100644 doc/README.hawkboard create mode 100644 include/configs/hawkboard.h create mode 100644 nand_spl/board/davinci/da8xxevm/Makefile create mode 100644 nand_spl/board/davinci/da8xxevm/u-boot.lds diff --git a/MAINTAINERS b/MAINTAINERS index 9258cb1..2a7d23d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -851,6 +851,11 @@ Alex Z lart SA1100 dnp1110 SA1110 +Syed Mohammed Khasim <sm.khasim(a)gmail.com> +Sughosh Ganu <urwithsughosh(a)gmail.com> + + hawkboard ARM926EJS (OMAP-L138) + ------------------------------------------------------------------------- Unknown / orphaned boards: diff --git a/arch/arm/include/asm/arch-davinci/da8xx_common.h b/arch/arm/include/asm/arch-davinci/da8xx_common.h index 7ae63a6..bc3092d 100644 --- a/arch/arm/include/asm/arch-davinci/da8xx_common.h +++ b/arch/arm/include/asm/arch-davinci/da8xx_common.h @@ -19,6 +19,9 @@ #ifndef __COMMON_H #define __COMMON_H +#define HAWKBOARD_KICK0_UNLOCK 0x83e70b13 +#define HAWKBOARD_KICK1_UNLOCK 0x95a4f1e0 + struct lpsc_resource { const int lpsc_no; }; diff --git a/arch/arm/include/asm/arch-davinci/hardware.h b/arch/arm/include/asm/arch-davinci/hardware.h index 3520cf8..d006ac1 100644 --- a/arch/arm/include/asm/arch-davinci/hardware.h +++ b/arch/arm/include/asm/arch-davinci/hardware.h @@ -379,7 +379,10 @@ int clk_get(enum davinci_clk_ids id); /* Boot config */ struct davinci_syscfg_regs { dv_reg revid; - dv_reg rsvd[71]; + dv_reg rsvd[13]; + dv_reg kick0; + dv_reg kick1; + dv_reg rsvd1[56]; dv_reg pinmux[20]; dv_reg suspsrc; dv_reg chipsig; diff --git a/board/davinci/common/Makefile b/board/davinci/common/Makefile index 8d9ea00..dd022f6 100644 --- a/board/davinci/common/Makefile +++ b/board/davinci/common/Makefile @@ -29,7 +29,7 @@ endif LIB = $(obj)lib$(VENDOR).a -COBJS := misc.o +COBJS := misc.o davinci_pinmux.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/davinci/common/davinci_pinmux.c b/board/davinci/common/davinci_pinmux.c new file mode 100644 index 0000000..ce58f71 --- /dev/null +++ b/board/davinci/common/davinci_pinmux.c @@ -0,0 +1,105 @@ +/* + * DaVinci pinmux functions. + * + * Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd, <nick.thompson(a)gefanuc.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * Copyright (C) 2008 Lyrtech <www.lyrtech.com> + * Copyright (C) 2004 Texas Instruments. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <common.h> +#include <asm/arch/hardware.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> + +/* + * Change the setting of a pin multiplexer field. + * + * Takes an array of pinmux settings similar to: + * + * struct pinmux_config uart_pins[] = { + * { &davinci_syscfg_regs->pinmux[8], 2, 7 }, + * { &davinci_syscfg_regs->pinmux[9], 2, 0 } + * }; + * + * Stepping through the array, each pinmux[n] register has the given value + * set in the pin mux field specified. + * + * The number of pins in the array must be passed (ARRAY_SIZE can provide + * this value conveniently). + * + * Returns 0 if all field numbers and values are in the correct range, + * else returns -1. + */ +int davinci_configure_pin_mux(const struct pinmux_config *pins, + const int n_pins) +{ + int i; + + /* check for invalid pinmux values */ + for (i = 0; i < n_pins; i++) { + if (pins[i].field >= PIN_MUX_NUM_FIELDS || + (pins[i].value & ~PIN_MUX_FIELD_MASK) != 0) + return -1; + } + + /* configure the pinmuxes */ + for (i = 0; i < n_pins; i++) { + const int offset = pins[i].field * PIN_MUX_FIELD_SIZE; + const unsigned int value = pins[i].value << offset; + const unsigned int mask = PIN_MUX_FIELD_MASK << offset; + const dv_reg *mux = pins[i].mux; + + writel(value | (readl(mux) & (~mask)), mux); + } + + return 0; +} + +/* + * Configure multiple pinmux resources. + * + * Takes an pinmux_resource array of pinmux_config and pin counts: + * + * const struct pinmux_resource pinmuxes[] = { + * PINMUX_ITEM(uart_pins), + * PINMUX_ITEM(i2c_pins), + * }; + * + * The number of items in the array must be passed (ARRAY_SIZE can provide + * this value conveniently). + * + * Each item entry is configured in the defined order. If configuration + * of any item fails, -1 is returned and none of the following items are + * configured. On success, 0 is returned. + */ +int davinci_configure_pin_mux_items(const struct pinmux_resource *item, + const int n_items) +{ + int i; + + for (i = 0; i < n_items; i++) { + if (davinci_configure_pin_mux(item[i].pins, + item[i].n_pins) != 0) + return -1; + } + + return 0; +} diff --git a/board/davinci/common/misc.c b/board/davinci/common/misc.c index a30047b..f25ad7e 100644 --- a/board/davinci/common/misc.c +++ b/board/davinci/common/misc.c @@ -95,78 +95,3 @@ void davinci_sync_env_enetaddr(uint8_t *rom_enetaddr) } #endif /* DAVINCI_EMAC */ - -/* - * Change the setting of a pin multiplexer field. - * - * Takes an array of pinmux settings similar to: - * - * struct pinmux_config uart_pins[] = { - * { &davinci_syscfg_regs->pinmux[8], 2, 7 }, - * { &davinci_syscfg_regs->pinmux[9], 2, 0 } - * }; - * - * Stepping through the array, each pinmux[n] register has the given value - * set in the pin mux field specified. - * - * The number of pins in the array must be passed (ARRAY_SIZE can provide - * this value conveniently). - * - * Returns 0 if all field numbers and values are in the correct range, - * else returns -1. - */ -int davinci_configure_pin_mux(const struct pinmux_config *pins, - const int n_pins) -{ - int i; - - /* check for invalid pinmux values */ - for (i = 0; i < n_pins; i++) { - if (pins[i].field >= PIN_MUX_NUM_FIELDS || - (pins[i].value & ~PIN_MUX_FIELD_MASK) != 0) - return -1; - } - - /* configure the pinmuxes */ - for (i = 0; i < n_pins; i++) { - const int offset = pins[i].field * PIN_MUX_FIELD_SIZE; - const unsigned int value = pins[i].value << offset; - const unsigned int mask = PIN_MUX_FIELD_MASK << offset; - const dv_reg *mux = pins[i].mux; - - writel(value | (readl(mux) & (~mask)), mux); - } - - return 0; -} - -/* - * Configure multiple pinmux resources. - * - * Takes an pinmux_resource array of pinmux_config and pin counts: - * - * const struct pinmux_resource pinmuxes[] = { - * PINMUX_ITEM(uart_pins), - * PINMUX_ITEM(i2c_pins), - * }; - * - * The number of items in the array must be passed (ARRAY_SIZE can provide - * this value conveniently). - * - * Each item entry is configured in the defined order. If configuration - * of any item fails, -1 is returned and none of the following items are - * configured. On success, 0 is returned. - */ -int davinci_configure_pin_mux_items(const struct pinmux_resource *item, - const int n_items) -{ - int i; - - for (i = 0; i < n_items; i++) { - if (davinci_configure_pin_mux(item[i].pins, - item[i].n_pins) != 0) - return -1; - } - - return 0; -} diff --git a/board/davinci/da8xxevm/Makefile b/board/davinci/da8xxevm/Makefile index 17cbe86..1a67351 100644 --- a/board/davinci/da8xxevm/Makefile +++ b/board/davinci/da8xxevm/Makefile @@ -30,6 +30,7 @@ LIB = $(obj)lib$(BOARD).a COBJS-y += common.o COBJS-$(CONFIG_MACH_DAVINCI_DA830_EVM) += da830evm.o COBJS-$(CONFIG_MACH_DAVINCI_DA850_EVM) += da850evm.o +COBJS-$(CONFIG_MACH_DAVINCI_HAWK) += hawkboard.o COBJS := $(COBJS-y) diff --git a/board/davinci/da8xxevm/hawkboard.c b/board/davinci/da8xxevm/hawkboard.c new file mode 100644 index 0000000..b672c9d --- /dev/null +++ b/board/davinci/da8xxevm/hawkboard.c @@ -0,0 +1,69 @@ +/* + * Modified for Hawkboard - Syed Mohammed Khasim <khasim(a)beagleboard.org> + * + * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar(a)ti.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include <common.h> +#include <asm/errno.h> +#include <asm/arch/hardware.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> +#include <ns16550.h> +#include <asm/arch/da8xx_common.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_init(void) +{ + /* arch number of the board */ + gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_HAWKBOARD; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + return 0; +} + +int board_early_init_f(void) +{ + /* + * Kick Registers need to be set to allow access to Pin Mux registers + */ + writel(HAWKBOARD_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); + writel(HAWKBOARD_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); + + /* set cfgchip3 to select mii */ + writel(readl(&davinci_syscfg_regs->cfgchip3) & + ~(1 << 8), &davinci_syscfg_regs->cfgchip3); + + return 0; +} + +int misc_init_r(void) +{ + char buf[32]; + + printf("ARM Clock : %s MHz\n", + strmhz(buf, clk_get(DAVINCI_ARM_CLKID))); + + return 0; +} diff --git a/board/davinci/da8xxevm/hawkboard_nand_spl.c b/board/davinci/da8xxevm/hawkboard_nand_spl.c new file mode 100644 index 0000000..74eec13 --- /dev/null +++ b/board/davinci/da8xxevm/hawkboard_nand_spl.c @@ -0,0 +1,158 @@ +/* + * Modified for Hawkboard - Syed Mohammed Khasim <khasim(a)beagleboard.org> + * + * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar(a)ti.com> + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * Copyright (C) 2004 Texas Instruments. + * + * ---------------------------------------------------------------------------- + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * ---------------------------------------------------------------------------- + */ + +#include <common.h> +#include <asm/errno.h> +#include <asm/arch/hardware.h> +#include <asm/io.h> +#include <asm/arch/davinci_misc.h> +#include <ns16550.h> +#include <asm/arch/da8xx_common.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define pinmux(x) (&davinci_syscfg_regs->pinmux[x]) + +static const struct pinmux_config mii_pins[] = { + { pinmux(2), 8, 1 }, + { pinmux(2), 8, 2 }, + { pinmux(2), 8, 3 }, + { pinmux(2), 8, 4 }, + { pinmux(2), 8, 5 }, + { pinmux(2), 8, 6 }, + { pinmux(2), 8, 7 } +}; + +static const struct pinmux_config mdio_pins[] = { + { pinmux(4), 8, 0 }, + { pinmux(4), 8, 1 } +}; + +static const struct pinmux_config nand_pins[] = { + { pinmux(7), 1, 1 }, + { pinmux(7), 1, 2 }, + { pinmux(7), 1, 4 }, + { pinmux(7), 1, 5 }, + { pinmux(9), 1, 0 }, + { pinmux(9), 1, 1 }, + { pinmux(9), 1, 2 }, + { pinmux(9), 1, 3 }, + { pinmux(9), 1, 4 }, + { pinmux(9), 1, 5 }, + { pinmux(9), 1, 6 }, + { pinmux(9), 1, 7 }, + { pinmux(12), 1, 5 }, + { pinmux(12), 1, 6 } +}; + +static const struct pinmux_config uart2_pins[] = { + { pinmux(0), 4, 6 }, + { pinmux(0), 4, 7 }, + { pinmux(4), 2, 4 }, + { pinmux(4), 2, 5 } +}; + +static const struct pinmux_config i2c_pins[] = { + { pinmux(4), 2, 4 }, + { pinmux(4), 2, 5 } +}; + +static const struct pinmux_resource pinmuxes[] = { + PINMUX_ITEM(mii_pins), + PINMUX_ITEM(mdio_pins), + PINMUX_ITEM(i2c_pins), + PINMUX_ITEM(nand_pins), + PINMUX_ITEM(uart2_pins), +}; + +static const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */ + { DAVINCI_LPSC_SPI1 }, /* Serial Flash */ + { DAVINCI_LPSC_EMAC }, /* image download */ + { DAVINCI_LPSC_UART2 }, /* console */ + { DAVINCI_LPSC_GPIO }, +}; + +void board_init_f(ulong bootflag) +{ + /* + * Kick Registers need to be set to allow access to Pin Mux registers + */ + writel(HAWKBOARD_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); + writel(HAWKBOARD_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); + + /* setup the SUSPSRC for ARM to control emulation suspend */ + writel(readl(&davinci_syscfg_regs->suspsrc) & + ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | + DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | + DAVINCI_SYSCFG_SUSPSRC_UART2), &davinci_syscfg_regs->suspsrc); + + /* Power on required peripherals + * ARM does not have acess by default to PSC0 and PSC1 + * assuming here that the DSP bootloader has set the IOPU + * such that PSC access is available to ARM + */ + da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)); + + /* configure pinmux settings */ + davinci_configure_pin_mux_items(pinmuxes, + ARRAY_SIZE(pinmuxes)); + + writel(readl(&davinci_uart2_ctrl_regs->pwremu_mgmt) | + (DAVINCI_UART_PWREMU_MGMT_FREE) | + (DAVINCI_UART_PWREMU_MGMT_URRST) | + (DAVINCI_UART_PWREMU_MGMT_UTRST), + &davinci_uart2_ctrl_regs->pwremu_mgmt); + + NS16550_init((NS16550_t)(DAVINCI_UART2_BASE), + CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); + + puts("Nand boot...\n"); + + nand_boot(); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} + +void putc(char c) +{ + if (gd->flags & GD_FLG_SILENT) + return; + + if (c == '\n') + NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), '\r'); + + NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), c); +} + +void hang(void) +{ + puts("### ERROR ### Please RESET the board ###\n"); + for (;;) + ; +} diff --git a/boards.cfg b/boards.cfg index 6c2a667..e2c73eb 100644 --- a/boards.cfg +++ b/boards.cfg @@ -372,6 +372,9 @@ davinci_sffsdr arm arm926ejs sffsdr davinci davinci davinci_sonata arm arm926ejs sonata davinci davinci da830evm arm arm926ejs da8xxevm davinci davinci da850evm arm arm926ejs da8xxevm davinci davinci +hawkboard arm arm926ejs da8xxevm davinci davinci hawkboard:SYS_TEXT_BASE=0xc1180000 +hawkboard_nand arm arm926ejs da8xxevm davinci davinci hawkboard:SYS_TEXT_BASE=0xc1080000,NAND_U_BOOT +hawkboard_uart arm arm926ejs da8xxevm davinci davinci hawkboard:SYS_TEXT_BASE=0xc1080000 guruplug arm arm926ejs - Marvell kirkwood mv88f6281gtw_ge arm arm926ejs - Marvell kirkwood openrd_base arm arm926ejs - Marvell kirkwood diff --git a/doc/README.hawkboard b/doc/README.hawkboard new file mode 100644 index 0000000..b7afec4 --- /dev/null +++ b/doc/README.hawkboard @@ -0,0 +1,93 @@ +Summary +======= +The README is for the boot procedure used for TI's OMAP-L138 based +hawkboard. The hawkboard comes with a 128MiB Nand flash and a 128MiB +DDR SDRAM along with a host of other controllers. + +The hawkboard is booted in three stages. The initial bootloader which +executes upon reset is the Rom Boot Loader(RBL) which sits in the +internal ROM of the omap. The RBL initialises the memory and the nand +controller, and copies the image stored at a predefined location(block +1) of the nand flash. The image loaded by the RBL to the memory is the +AIS signed nand_spl image. This, in turns copies the u-boot binary +from the nand flash to the memory and jumps to the u-boot entry point. + +AIS is an image format defined by TI for the images that are to be +loaded to memory by the RBL. The image is divided into a series of +sections and the image's entry point is specified. Each section comes +with meta data like the target address the section is to be copied to +and the size of the section, which is used by the RBL to load the +image. At the end of the image the RBL jumps to the image entry +point. + +The secondary stage bootloader(nand_spl) which is loaded by the RBL +then loads the u-boot from a predefined location in the nand to the +memory and jumps to the u-boot entry point. + +The reason a secondary stage bootloader is used is because the ECC +layout expected by the RBL is not the same as that used by +u-boot/linux. This also implies that for flashing the nand_spl image, +we need to use the u-boot which uses the ECC layout expected by the +RBL[1]. Booting u-boot over UART(UART boot) is explained here[2]. + + +Compilation +=========== +Three images might be needed + +* nand_spl - This is the secondary bootloader which boots the u-boot + binary. + + hawkboard_nand_config + + The nand_spl ELF gets generated under nand_spl/u-boot-spl. This + needs to be processed with the AISGen tool for generating the AIS + signed image to be flashed. Steps for generating the AIS image are + explained here[3]. + +* u-boot binary - This is the image flashed to the nand and copied to + the memory by the nand_spl. + + hawkboard_config + +* u-boot for uart boot - This is same as the u-boot binary generated + above, with the sole difference of the CONFIG_SYS_TEXT_BASE being + 0xc1080000, as expected by the RBL. + + hawkboard_uart_config + + +Flashing the images to Nand +=========================== +The nand_spl AIS image needs to be flashed to the block 1 of the +Nand flash, as that is the location the RBL expects the image[4]. For +flashing the nand_spl, boot over the u-boot specified in [1], and +flash the image + +=> tftpboot 0xc0700000 <nand_spl_ais.bin> +=> nand erase 0x20000 0x20000 +=> nand write.e 0xc0700000 0x20000 <nand_spl_size> + +The u-boot binary is flashed at location 0xe0000(block 6) of the nand +flash. The nand_spl loader expects the u-boot at this location. For +flashing the u-boot binary + +=> tftpboot 0xc0700000 u-boot.bin +=> nand erase 0xe0000 0x40000 +=> nand write.e 0xc0700000 0xe0000 <u-boot-size> + + +Links +===== + +[1] + http://code.google.com/p/hawkboard/downloads/detail?name=u-boot_uart_ais_v1… + +[2] + http://elinux.org/Hawkboard#Booting_u-boot_over_UART + +[3] + http://elinux.org/Hawkboard#Signing_u-boot_for_UART_boot + +[4] + http://processors.wiki.ti.com/index.php/RBL_UBL_and_host_program#RBL_bootin… diff --git a/include/configs/hawkboard.h b/include/configs/hawkboard.h new file mode 100644 index 0000000..5cf8f5c --- /dev/null +++ b/include/configs/hawkboard.h @@ -0,0 +1,200 @@ +/* + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn <ksi(a)koi8.net> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Board + */ +#define CONFIG_SYS_USE_NAND 1 + +/* + * SoC Configuration + */ +#define CONFIG_MACH_DAVINCI_HAWK +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (1*1024*1024) /* malloc() len */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE +#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 -\ + GENERATED_GBL_DATA_SIZE) + +/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1) + +/* memtest will be run on 16MB */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024) + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024) /* regular stack */ + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Network & Ethernet Configuration + */ +#define CONFIG_EMAC_MDIO_PHY_NUM 0x7 +#if !defined(CONFIG_NAND_SPL) +#define CONFIG_DRIVER_TI_EMAC +#endif +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI + +/* + * Nand Flash + */ +#ifdef CONFIG_SYS_USE_NAND +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_CLE_MASK 0x10 +#define CONFIG_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CFG_DAVINCI_STD_NAND_LAYOUT +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_PAGE_2K +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +/* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE_LIST { 0x62000000, } +#define NAND_MAX_CHIPS 1 +/* Block 0--not used by bootcode */ +#define CONFIG_ENV_OFFSET 0x0 + +#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0xe0000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x40000 +#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1180000 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ + CONFIG_SYS_NAND_U_BOOT_SIZE - \ + CONFIG_SYS_MALLOC_LEN - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_NAND_ECCPOS { \ + 24, 25, 26, 27, 28, \ + 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ + 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ + 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ + 59, 60, 61, 62, 63 } +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 10 +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \ + CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \ + CONFIG_SYS_NAND_ECCSTEPS) +#endif /* CONFIG_SYS_USE_NAND */ + +/* + * U-Boot general configuration + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CONFIG_SYS_PROMPT "hawkboard > " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS \ + "mem=128M console=ttyS2,115200n8 root=/dev/ram0 rw initrd=0xc1180000,"\ + "4M ip=static" +#define CONFIG_BOOTDELAY 3 + +/* + * U-Boot commands + */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY + +#ifdef CONFIG_SYS_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND +#endif + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_PING +#endif + +#endif /* __CONFIG_H */ diff --git a/nand_spl/board/davinci/da8xxevm/Makefile b/nand_spl/board/davinci/da8xxevm/Makefile new file mode 100644 index 0000000..6102675 --- /dev/null +++ b/nand_spl/board/davinci/da8xxevm/Makefile @@ -0,0 +1,141 @@ +# +# (C) Copyright 2006-2007 +# Stefan Roese, DENX Software Engineering, sr(a)denx.de. +# +# (C) Copyright 2008 +# Guennadi Liakhovetki, DENX Software Engineering, <lg(a)denx.de> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +CONFIG_NAND_SPL = y + +include $(TOPDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL + +SOBJS = start.o _udivsi3.o _divsi3.o +COBJS = cpu.o davinci_nand.o ns16550.o div0.o davinci_pinmux.o psc.o \ + common.o hawkboard_nand_spl.o nand_boot.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin \ + $(nandobj)u-boot-spl-16k.bin + +all: $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +$(nandobj)u-boot.lds: $(LDSCRIPT) + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ + +# create symbolic links for common files + +# from board directory +$(obj)davinci_pinmux.c: + @rm -f $@ + @ln -s $(TOPDIR)/board/davinci/common/davinci_pinmux.c $@ + +# from drivers/mtd/nand directory +$(obj)davinci_nand.c: + @rm -f $@ + @ln -s $(TOPDIR)/drivers/mtd/nand/davinci_nand.c $@ + +# from nand_spl directory +$(obj)nand_boot.c: + @rm -f $@ + @ln -s $(TOPDIR)/nand_spl/nand_boot.c $@ + +# from drivers/serial directory +$(obj)ns16550.c: + @rm -f $@ + @ln -sf $(TOPDIR)/drivers/serial/ns16550.c $@ + +# from cpu directory +$(obj)start.S: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/start.S $@ + +# from lib directory +$(obj)_udivsi3.S: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/lib/_udivsi3.S $@ + +# from lib directory +$(obj)_divsi3.S: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/lib/_divsi3.S $@ + +# from lib directory +$(obj)div0.c: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/lib/div0.c $@ + +# from SoC directory +$(obj)cpu.c: + @rm -f $@ + @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/cpu.c $@ + +# from board directory +$(obj)hawkboard_nand_spl.c: + @rm -f $@ + ln -s $(TOPDIR)/board/davinci/da8xxevm/hawkboard_nand_spl.c $@ + +# from board directory +$(obj)common.c: + @rm -f $@ + ln -s $(TOPDIR)/board/davinci/da8xxevm/common.c $@ + +$(obj)psc.c: + @rm -f $@ + ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/psc.c $@ + + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/davinci/da8xxevm/u-boot.lds b/nand_spl/board/davinci/da8xxevm/u-boot.lds new file mode 100644 index 0000000..f6ccf08 --- /dev/null +++ b/nand_spl/board/davinci/da8xxevm/u-boot.lds @@ -0,0 +1,75 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, <garyj(a)denx.de> + * + * (C) Copyright 2008 + * Guennadi Liakhovetki, DENX Software Engineering, <lg(a)denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0xc1080000; + + . = ALIGN(4); + .text : + { + start.o (.text) + cpu.o (.text) + nand_boot.o (.text) + + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { + *(.data) + __datarel_start = .; + *(.data.rel) + __datarelrolocal_start = .; + *(.data.rel.ro.local) + __datarellocal_start = .; + *(.data.rel.local) + __datarelro_start = .; + *(.data.rel.ro) + } + + . = ALIGN(4); + __rel_dyn_start = .; + __rel_dyn_end = .; + __dynsym_start = .; + + __got_start = .; + . = ALIGN(4); + .got : { *(.got) } + + __got_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/nand_spl/nand_boot.c b/nand_spl/nand_boot.c index b9fd6f5..76b8566 100644 --- a/nand_spl/nand_boot.c +++ b/nand_spl/nand_boot.c @@ -236,6 +236,7 @@ void nand_boot(void) /* * Init board specific nand support */ + nand_chip.select_chip = NULL; nand_info.priv = &nand_chip; nand_chip.IO_ADDR_R = nand_chip.IO_ADDR_W = (void __iomem *)CONFIG_SYS_NAND_BASE; nand_chip.dev_ready = NULL; /* preset to NULL */ -- 1.7.0.4

1 0

[U-Boot] [PATCH 1/3 V5] Move and rename common headers from under board/davinci.
by Sughosh Ganu 01 Nov '10

01 Nov '10

Move the davinci common headers to the architecture specific include file path. Signed-off-by: Sughosh Ganu <urwithsughosh(a)gmail.com> --- Changes since V4: * No change in this patch of the patchset .../arm/include/asm/arch-davinci/da8xx_common.h | 0 .../arm/include/asm/arch-davinci/davinci_misc.h | 0 board/davinci/common/misc.c | 2 +- board/davinci/da8xxevm/common.c | 2 +- board/davinci/da8xxevm/da830evm.c | 4 ++-- board/davinci/da8xxevm/da850evm.c | 4 ++-- board/davinci/dm355evm/dm355evm.c | 2 +- board/davinci/dm355leopard/dm355leopard.c | 2 +- board/davinci/dm365evm/dm365evm.c | 2 +- board/davinci/dvevm/dvevm.c | 2 +- board/davinci/schmoogie/schmoogie.c | 2 +- board/davinci/sffsdr/sffsdr.c | 2 +- board/davinci/sonata/sonata.c | 2 +- 13 files changed, 13 insertions(+), 13 deletions(-) rename board/davinci/da8xxevm/common.h => arch/arm/include/asm/arch-davinci/da8xx_common.h (100%) rename board/davinci/common/misc.h => arch/arm/include/asm/arch-davinci/davinci_misc.h (100%) diff --git a/board/davinci/da8xxevm/common.h b/arch/arm/include/asm/arch-davinci/da8xx_common.h similarity index 100% rename from board/davinci/da8xxevm/common.h rename to arch/arm/include/asm/arch-davinci/da8xx_common.h diff --git a/board/davinci/common/misc.h b/arch/arm/include/asm/arch-davinci/davinci_misc.h similarity index 100% rename from board/davinci/common/misc.h rename to arch/arm/include/asm/arch-davinci/davinci_misc.h diff --git a/board/davinci/common/misc.c b/board/davinci/common/misc.c index b60a46e..71e7822 100644 --- a/board/davinci/common/misc.c +++ b/board/davinci/common/misc.c @@ -29,7 +29,7 @@ #include <net.h> #include <asm/arch/hardware.h> #include <asm/io.h> -#include "misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/da8xxevm/common.c b/board/davinci/da8xxevm/common.c index 9cd5204..36bf693 100644 --- a/board/davinci/da8xxevm/common.c +++ b/board/davinci/da8xxevm/common.c @@ -20,7 +20,7 @@ #include <asm/io.h> #include <asm/arch/hardware.h> -#include "common.h" +#include <asm/arch/da8xx_common.h> #ifndef CONFIG_USE_IRQ void irq_init(void) diff --git a/board/davinci/da8xxevm/da830evm.c b/board/davinci/da8xxevm/da830evm.c index 8a9f988..b6b7e37 100644 --- a/board/davinci/da8xxevm/da830evm.c +++ b/board/davinci/da8xxevm/da830evm.c @@ -40,8 +40,8 @@ #include <asm/arch/emif_defs.h> #include <asm/arch/emac_defs.h> #include <asm/io.h> -#include "../common/misc.h" -#include "common.h" +#include <asm/arch/davinci_misc.h> +#include <asm/arch/da8xx_common.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/da8xxevm/da850evm.c b/board/davinci/da8xxevm/da850evm.c index c8c5e1b..0420ad5 100644 --- a/board/davinci/da8xxevm/da850evm.c +++ b/board/davinci/da8xxevm/da850evm.c @@ -29,8 +29,8 @@ #include <asm/arch/emif_defs.h> #include <asm/arch/emac_defs.h> #include <asm/io.h> -#include "../common/misc.h" -#include "common.h" +#include <asm/arch/davinci_misc.h> +#include <asm/arch/da8xx_common.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/dm355evm/dm355evm.c b/board/davinci/dm355evm/dm355evm.c index 87f284c..b9260b8 100644 --- a/board/davinci/dm355evm/dm355evm.c +++ b/board/davinci/dm355evm/dm355evm.c @@ -22,7 +22,7 @@ #include <asm/arch/hardware.h> #include <asm/arch/emif_defs.h> #include <asm/arch/nand_defs.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> #include <net.h> #include <netdev.h> diff --git a/board/davinci/dm355leopard/dm355leopard.c b/board/davinci/dm355leopard/dm355leopard.c index e89786e..0ee0d11 100644 --- a/board/davinci/dm355leopard/dm355leopard.c +++ b/board/davinci/dm355leopard/dm355leopard.c @@ -22,7 +22,7 @@ #include <asm/arch/hardware.h> #include <asm/arch/gpio_defs.h> #include <asm/arch/nand_defs.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> #include <net.h> #include <netdev.h> diff --git a/board/davinci/dm365evm/dm365evm.c b/board/davinci/dm365evm/dm365evm.c index 85dbe2a..bc681f7 100644 --- a/board/davinci/dm365evm/dm365evm.c +++ b/board/davinci/dm365evm/dm365evm.c @@ -24,7 +24,7 @@ #include <asm/arch/nand_defs.h> #include <asm/arch/gpio_defs.h> #include <netdev.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c index 073c21a..d5c851b 100644 --- a/board/davinci/dvevm/dvevm.c +++ b/board/davinci/dvevm/dvevm.c @@ -27,7 +27,7 @@ #include <common.h> #include <i2c.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/schmoogie/schmoogie.c b/board/davinci/schmoogie/schmoogie.c index 80a0f9f..8b615a9 100644 --- a/board/davinci/schmoogie/schmoogie.c +++ b/board/davinci/schmoogie/schmoogie.c @@ -27,7 +27,7 @@ #include <common.h> #include <i2c.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; diff --git a/board/davinci/sffsdr/sffsdr.c b/board/davinci/sffsdr/sffsdr.c index 657cf2b..cc3ff7d 100644 --- a/board/davinci/sffsdr/sffsdr.c +++ b/board/davinci/sffsdr/sffsdr.c @@ -30,7 +30,7 @@ #include <common.h> #include <i2c.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> #define DAVINCI_A3CR (0x01E00014) /* EMIF-A CS3 config register. */ #define DAVINCI_A3CR_VAL (0x3FFFFFFD) /* EMIF-A CS3 value for FPGA. */ diff --git a/board/davinci/sonata/sonata.c b/board/davinci/sonata/sonata.c index 1dc42c4..c194290 100644 --- a/board/davinci/sonata/sonata.c +++ b/board/davinci/sonata/sonata.c @@ -28,7 +28,7 @@ #include <nand.h> #include <asm/arch/nand_defs.h> #include <asm/arch/hardware.h> -#include "../common/misc.h" +#include <asm/arch/davinci_misc.h> DECLARE_GLOBAL_DATA_PTR; -- 1.7.0.4

1 0

[U-Boot] [PATCH] UBIFS: Change ubifsload to not read beyond the requested size
by Stefan Roese 01 Nov '10

01 Nov '10

Until now ubifsload pads the destination with 0 up to a multiple of UBIFS_BLOCK_SIZE (4KiB) while reading a file to memory. This patch changes this behaviour to only read to the requested length. This is either the file length or the length/size provided as parameter to the ubifsload command. Signed-off-by: Stefan Roese <sr(a)denx.de> --- This patch makes the patch [UBIFS: Add padded size to ubifsload output] posted yesterday obsolete since we're not padding any more now. Stefan fs/ubifs/ubifs.c | 58 ++++++++++++++++++++++++++++++++++++++++------------- 1 files changed, 44 insertions(+), 14 deletions(-) diff --git a/fs/ubifs/ubifs.c b/fs/ubifs/ubifs.c index 8215443..e49ae6f 100644 --- a/fs/ubifs/ubifs.c +++ b/fs/ubifs/ubifs.c @@ -3,7 +3,7 @@ * * Copyright (C) 2006-2008 Nokia Corporation. * - * (C) Copyright 2008-2009 + * (C) Copyright 2008-2010 * Stefan Roese, DENX Software Engineering, sr(a)denx.de. * * This program is free software; you can redistribute it and/or modify it @@ -567,7 +567,8 @@ dump: return -EINVAL; } -static int do_readpage(struct ubifs_info *c, struct inode *inode, struct page *page) +static int do_readpage(struct ubifs_info *c, struct inode *inode, + struct page *page, int last_block_size) { void *addr; int err = 0, i; @@ -601,17 +602,39 @@ static int do_readpage(struct ubifs_info *c, struct inode *inode, struct page *p err = -ENOENT; memset(addr, 0, UBIFS_BLOCK_SIZE); } else { - ret = read_block(inode, addr, block, dn); - if (ret) { - err = ret; - if (err != -ENOENT) - break; - } else if (block + 1 == beyond) { - int dlen = le32_to_cpu(dn->size); - int ilen = i_size & (UBIFS_BLOCK_SIZE - 1); - - if (ilen && ilen < dlen) - memset(addr + ilen, 0, dlen - ilen); + /* + * Reading last block? Make sure to not write beyond + * the requested size. + */ + if (((block + 1) == beyond) || last_block_size) { + void *buff; + int dlen; + + /* + * We need to buffer the data locally for the + * last block. This is to not pad the destination + * area to a multiple of UBIFS_BLOCK_SIZE. + */ + buff = malloc(UBIFS_BLOCK_SIZE); + + /* Read block-siez into temp buffer */ + ret = read_block(inode, buff, block, dn); + if (last_block_size) + dlen = last_block_size; + else + dlen = le32_to_cpu(dn->size); + + /* Now copy required size back to dest */ + memcpy(addr, buff, dlen); + + free(buff); + } else { + ret = read_block(inode, addr, block, dn); + if (ret) { + err = ret; + if (err != -ENOENT) + break; + } } } if (++i >= UBIFS_BLOCKS_PER_PAGE) @@ -649,6 +672,7 @@ int ubifs_load(char *filename, u32 addr, u32 size) int err = 0; int i; int count; + int last_block_size = 0; c->ubi = ubi_open_volume(c->vi.ubi_num, c->vi.vol_id, UBI_READONLY); /* ubifs_findfile will resolve symlinks, so we know that we get @@ -684,7 +708,13 @@ int ubifs_load(char *filename, u32 addr, u32 size) page.index = 0; page.inode = inode; for (i = 0; i < count; i++) { - err = do_readpage(c, inode, &page); + /* + * Make sure to not read beyond the requested size + */ + if (((i + 1) == count) && (size < inode->i_size)) + last_block_size = size - (i * PAGE_SIZE); + + err = do_readpage(c, inode, &page, last_block_size); if (err) break; -- 1.7.3.2

3 4

[U-Boot] [PATCH] arm: get_sp() should always be compiled
by ratbert.chuang＠gmail.com 01 Nov '10

01 Nov '10

From: Po-Yu Chuang <ratbert(a)faraday-tech.com> get_sp() was incorrectly excluded if none of CONFIG_SETUP_MEMORY_TAGS CONFIG_CMDLINE_TAG CONFIG_INITRD_TAG CONFIG_SERIAL_TAG CONFIG_REVISION_TAG were defined. Signed-off-by: Po-Yu Chuang <ratbert(a)faraday-tech.com> --- arch/arm/lib/bootm.c | 4 +--- 1 files changed, 1 insertions(+), 3 deletions(-) diff --git a/arch/arm/lib/bootm.c b/arch/arm/lib/bootm.c index a1649ee..7734953 100644 --- a/arch/arm/lib/bootm.c +++ b/arch/arm/lib/bootm.c @@ -327,12 +327,12 @@ void setup_revision_tag(struct tag **in_params) } #endif /* CONFIG_REVISION_TAG */ - static void setup_end_tag (bd_t *bd) { params->hdr.tag = ATAG_NONE; params->hdr.size = 0; } +#endif /* CONFIG_SETUP_MEMORY_TAGS || CONFIG_CMDLINE_TAG || CONFIG_INITRD_TAG */ static ulong get_sp(void) { @@ -341,5 +341,3 @@ static ulong get_sp(void) asm("mov %0, sp" : "=r"(ret) : ); return ret; } - -#endif /* CONFIG_SETUP_MEMORY_TAGS || CONFIG_CMDLINE_TAG || CONFIG_INITRD_TAG */ -- 1.6.3.3

1 0