November 2010 - U-Boot

[U-Boot] Can't start Linux if U-Boot built with CONFIG_WATCHDOG
by Matthew Lear 26 Aug '15

26 Aug '15

Hello all, I've added watchdog support based on U-Boot (git) for the m68k coldfire mcf54455evb platform. I've fed the patch to the maintainer to help in development. However, I am unable to start my m68k w/MMU coldfire Linux kernel from U-Boot if U-Boot is built with CONFIG_WATCHDOG regardless if the watchdog_enable(), watchdog_reset() and watchdog_disable() functions touch hardware or not. I initially thought this was a problem with enabling the watchdog somehow (ie when Linux started, some hw configuration in the device was getting upset or corrupted etc resulting in the failure), but when I commented out the code from the above functions that actually accesses the hw (ie to enable, kick and disable the watchdog timer hw block), Linux is still unable to start. In fact, I don't think Linux actually gets started! That's the problem. If I rebuild the same U-Boot code base with CONFIG_WATCHDOG undefined, Linux can start just fine. As far as I can tell, there are no functional differences in building U-Boot with or without CONFIG_WATCHDOG enabled when the functions above are stubs and do absolutely nothing at all. If I build U-Boot with debug, what I see is as follows: ## Transferring control to Linux (at address 40020000) ... BIV ...and then the board is dead. I occasionally see something like the following from U-Boot: *** Unexpected exception *** Vector Number: 4 Format: 04 Fault Status: 0 PC: 4fdbfdc8 SR: 00002700 SP: 4fd72a64 D0: 00000004 D1: 000003f9 D2: 4fdb4202 D3: 004fa3da D4: 00000000 D5: 4fdc7c8c D6: 122c0034 D7: 4fd82f76 A0: 4033cb98 A1: 4025aa39 A2: 40020000 A3: 4fdbfdc8 A4: 00000000 A5: 4fdc5800 A6: 4fd72afb *** Please Reset Board! *** The 'BIV' is relevant because in my 2.6.29 kernel src arch/m68k/include/asm/bootinfo_mm.h, BOOTINFOV_MAGIC is defined to be 0x4249561A which is BIV^Z. This ascii text is located in the kernel image header info: >From arch/m68k/coldfire/head.S: .section ".text.head","ax" ENTRY(_stext) bras 1f /* Jump over bootinfo version numbers */ .long BOOTINFOV_MAGIC .long 0 And from U-Boot itself: -> md ${loadaddr} 40010000: 27051956 97342d7d 4a54afd5 00300000 '..V.4-}JT...0.. 40010010: 40020000 40020000 8a006fc1 050c0200 @...@.....o..... 40010020: 4c696e75 78204b65 726e656c 20496d61 Linux Kernel Ima 40010030: 67650000 00000000 00000000 00000000 ge.............. 40010040: 60084249 561a0000 00004ef9 40304000 `.BIV.....N.@0@. I suspect that the failure of starting Linux is caused by some mismatch in data structures (or versions there of) shared/copied between Linux and U-Boot and that this data has somehow changed when U-Boot is built with CONFIG_WATCHDOG #defined. However, I can't find any evidence of this in the U-Boot code base. The bras instruction above must be key and I suspect that this is the area causing the problem. Can anybody offer any advice / explanation of what exactly could be going on and why? I wouldn't have expected that defining CONFIG_WATCHDOG would change anything as fundamental as this. Apologies for the cross-post (U-Boot and m68k kernel dev) but I hope to get opinions/feedback/help from both communities. Any assistance very much appreciated indeed. Many thanks, -- Matt

2 1

[U-Boot] [PATCH] fsl: Fix compiler warnings from gcc-4.4 in sys_eeprom code
by Kumar Gala 30 Aug '13

30 Aug '13

sys_eeprom.c: In function 'do_mac': sys_eeprom.c:323: warning: dereferencing type-punned pointer will break strict-aliasing rules sys_eeprom.c: In function 'mac_read_from_eeprom': sys_eeprom.c:395: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Kumar Gala <galak(a)kernel.crashing.org> --- board/freescale/common/sys_eeprom.c | 6 ++++-- 1 files changed, 4 insertions(+), 2 deletions(-) diff --git a/board/freescale/common/sys_eeprom.c b/board/freescale/common/sys_eeprom.c index ae5304a..3e1e332 100644 --- a/board/freescale/common/sys_eeprom.c +++ b/board/freescale/common/sys_eeprom.c @@ -78,12 +78,14 @@ static int has_been_read = 0; #ifdef CONFIG_SYS_I2C_EEPROM_NXID /* Is this a valid NXID EEPROM? */ -#define is_valid (*((u32 *)e.id) == (('N' << 24) | ('X' << 16) | ('I' << 8) | 'D')) +#define is_valid ((e.id[0] == 'N') || (e.id[1] == 'X') || \ + (e.id[2] == 'I') || (e.id[3] == 'D')) #endif #ifdef CONFIG_SYS_I2C_EEPROM_CCID /* Is this a valid CCID EEPROM? */ -#define is_valid (*((u32 *)e.id) == (('C' << 24) | ('C' << 16) | ('I' << 8) | 'D')) +#define is_valid ((e.id[0] == 'C') || (e.id[1] == 'C') || \ + (e.id[2] == 'I') || (e.id[3] == 'D')) #endif /** -- 1.6.0.6

2 1

[U-Boot-Users] minimum bdi config to read flash on 85xx
by robert lazarski 28 May '13

28 May '13

Hi all, On our custom 8548 board, we can't read our flash correctly. We have one 1Gb bank of spansion S29GL01GP flash and we get: atum>mdh 0xf8000000 0_f8000000 : f9f7 f9f7 f9f7 f9f7 f9f7 f9f7 f9f7 f9f7 The big problem we have now: is this a hardware issue or a bdi config issue? Aside from the flash we have 1GigaByte of DDR ram. Can anyone help us track our flash issues down to be hardware, config file, or some combination? The hardware guys think the board is fine. We've been deep into the manuals of both the 8548 and the bdi and can't find anything wrong. Here's the config, thanks for any help! ;bdiGDB configuration file for ATUM 8548 ;--------------------------------------------------- ; [INIT] ; ; ; use the following two lines for STARTUP HALT WSPR 63 0xffff0000 ;IVPR to boot core WSPR 415 0x0000f000 ;IVOR15 : Debug exception ; ; ;================= setup for flash programming =============== ; Move CCSRBAR to 0xe0000000 WM32 0xff700000 0x000e0000 ;CCSRBAR to 0xe0000000 ; ; Initialize LAWBAR's WM32 0xe0000C08 0x00000000 ;LAWBAR0 : @0x00000000 WM32 0xe0000C10 0x80f0001d ;LAWAR0 : DDR 1GB WM32 0xe0000C28 0xf8000000 ;LAWBAR1 : @0xf8000000 WM32 0xe0000C30 0x8040001a ;LAWAR1 : Local Bus 128MB for S29GL01GP ; ; Setup Flash chip select WM32 0xe0005000 0xf8001001 ;BR0 WM32 0xe0005004 0xf8000E65 ;OR0 ; CS0_BNDS WM32 0xe0002000 0x0000000f ; DDR CS0 ; CS0_CONFIG WM32 0xe0002080 0x80000102 ; TIMING_CFG_0 WM32 0xe0002104 0x00260802 ; TIMING_CFG_1 WM32 0xe0002108 0x38355322 ; TIMING_CFG_2 WM32 0xe000210C 0x039048c7 ; DDR_SDRAM_MODE WM32 0xe0002118 0x00000432 ; DDR_SDRAM_INTERVAL WM32 0xe0002124 0x05150100 ; DDR_SDRAM_CFG2 WM32 0xe0002114 0x24000000 ; DDR_SDRAM_CLK_CNTL WM32 0xe0002130 0x03000000 DELAY 200 ; enable the memory interface ; DDR_SDRAM_CFG ; enable the memory interface WM32 0xe0002110 0xc3000000 ;================= end flash programming ===================== ; [TARGET] CPUTYPE 8548 ;the CPU type JTAGCLOCK 0 ;use 16 MHz JTAG clock ;STARTUP STOP 5000 ;let U-boot code setup the system STARTUP HALT ;halt core while HRESET is asserted BREAKMODE HARD ;SOFT or HARD, HARD uses PPC hardware breakpoint STEPMODE HWBP ;JTAG or HWBP, HWBP uses a hardware breakpoint WAKEUP 500 ;give reset time to complete POWERUP 5000 ;start delay after power-up detected in ms [REGS] FILE $reg8548.def [HOST] IP 10.101.43.10 FILE vmlinux.8548 FORMAT ELF LOAD MANUAL ;load code MANUAL or AUTO after reset DUMP e500.bin PROMPT atum> [FLASH] CHIPTYPE MIRRORX16 ;S29GL01GP CHIPSIZE 0x8000000 ;The size of one flash chip in bytes - 1Gb BUSWIDTH 16 ;The width of the flash memory bus in bits (8 | 16 | 32) FILE u-boot.bin FORMAT BIN 0xF8000000 ERASE 0xF8000000 ;erase sector 0 [REGS] FILE $reg8548.def

10 42

[U-Boot] Add new NAND flash
by Matthias Weißer 05 Mar '13

05 Mar '13

Hi I would like to add a new NAND flash type to u-boot and have some problems with it. The type is MT29F16G08CBABA – Page size x8: 4320 bytes (4096 + 224 bytes) – Block size: 256 pages (1024K + 56K bytes) – Plane size: 2 planes x 1024 blocks per plane – Device size: 16Gb: 2048 blocks The NAND subsystem is configured as follows #define CONFIG_NAND_MXC #define CONFIG_NAND_MXC_V1_1 #define CONFIG_MXC_NAND_REGS_BASE (0xBB000000) #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE (0xBB000000) #define CONFIG_MXC_NAND_HWECC #define CONFIG_SYS_NAND_LARGEPAGE The NAND is connected (8 bit wide) to an iMX25 which is booting from NOR. So the NAND is only a mass storage device. I am able to read the ID of the chip. 2Ch 48h 04h 46h 85h I then added the following entry to the nand_flash_ids[] table {"NAND 2GiB 3,3V 8-bit", 0x48, 0, 2048, 0, LP_OPTIONS}, Before getting to the u-boot prompt I get the following message: NAND: NAND device: Manufacturer ID: 0x2c, Chip ID: 0x48 (Micron NAND 2GiB 3,3V 8-bit) NAND bus width 8 instead 16 bit This is caused by bit 6 in id byte 4 which tells that the device is 16 bit wide organized and the iMX specific part of the NAND system which tells the generic system that the device is connected via a 8 bit bus which is obviously correct as the flash chip only has 8 data lines. Is there anything I am doing wrong here? Thanks, Matthias

3 5

[U-Boot] [PATCH v4] Marvell MV88E61XX Switch Driver support
by Prafulla Wadaskar 25 Jan '13

25 Jan '13

Chips supported:- 1. 88E6161 6 port gbe swtich with 5 integrated PHYs 2. 88E6165 6 port gbe swtich with 5 integrated PHYs 2. 88E6132 3 port gbe swtich with 2 integrated PHYs Platform specific configuration supported Note: This driver is supported and tested against kirkwood egiga interface Contributors: Yotam Admon <yotam(a)marvell.com> Michael Blostein <michaelbl(a)marvell.com Reviewed by: Ronen Shitrit <rshitrit(a)marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla(a)marvell.com> --- Changelog:- v2: updated as per review comments for v1 removed other two drivers form earlier patch debug_prints removed driver moved to drivers/net/ v3: updated as per review comments for v2 miiphy interface used, platform specific dependency resolved Chip id detection and printing added common code forked out some cosmetic and magic number fixes v4: updated as per review comments for v3 mv88e61xx.h added platform specific configuration support added some more documentation references provided cleaned rgmii delay enable related code drivers/net/Makefile | 1 + drivers/net/mv88e61xx.c | 296 +++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/mv88e61xx.h | 73 ++++++++++++ 3 files changed, 370 insertions(+), 0 deletions(-) create mode 100644 drivers/net/mv88e61xx.c create mode 100644 drivers/net/mv88e61xx.h diff --git a/drivers/net/Makefile b/drivers/net/Makefile index a360a50..7d397d6 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -46,6 +46,7 @@ COBJS-$(CONFIG_MACB) += macb.o COBJS-$(CONFIG_MCFFEC) += mcffec.o mcfmii.o COBJS-$(CONFIG_MPC5xxx_FEC) += mpc5xxx_fec.o COBJS-$(CONFIG_MPC512x_FEC) += mpc512x_fec.o +COBJS-$(CONFIG_MV88E61XX_SWITCH) += mv88e61xx.o COBJS-$(CONFIG_NATSEMI) += natsemi.o COBJS-$(CONFIG_DRIVER_NE2000) += ne2000.o ne2000_base.o COBJS-$(CONFIG_DRIVER_AX88796L) += ax88796.o ne2000_base.o diff --git a/drivers/net/mv88e61xx.c b/drivers/net/mv88e61xx.c new file mode 100644 index 0000000..713e728 --- /dev/null +++ b/drivers/net/mv88e61xx.c @@ -0,0 +1,296 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include <common.h> +#include <miiphy.h> +#include "mv88e61xx.h" + +/* Chip Address mode + * The Switch support two modes of operation + * 1. single chip mode and + * 2. Multi-chip mode + * Refer section 9.2 &9.3 in chip datasheet-02 for more details + * + * By default single chip mode is configured + * multichip mode operation can be configured in board header + */ +#ifndef CONFIG_MV88E61XX_MULTICHIP_ADRMODE +#define mv88e61xx_wr_phy miiphy_write +#define mv88e61xx_rd_phy miiphy_read +#else + +static int mv88e61xx_busychk_multic(u32 devaddr) +{ + u32 reg = 0; + u32 timeout = MV88E61XX_PHY_TIMEOUT; + + /* Poll till SMIBusy bit is clear */ + do { + miiphy_read(name, devaddr, 0x0, &reg); + if (timeout-- == 0) { + printf("SMI busy timeout\n"); + return -1; + } + } while (reg & BIT15); + return 0; +} + +static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data) +{ + u16 reg; + u32 mii_dev_addr; + + /* command to read PHY dev address */ + miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr); + mv88e61xx_busychk_multic(mii_dev_addr); + /* Write data to Switch indirect data register */ + miiphy_write(name, mii_dev_addr, 0x1, data); + /* Write command to Switch indirect command register (write) */ + miiphy_write(name, mii_dev_addr, 0x0, + reg_ofs | (phy_adr << 5) | BIT10 | BIT12 | BIT15); +} + +static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data) +{ + u16 reg; + u32 mii_dev_addr; + + /* command to read PHY dev address */ + miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr); + mv88e61xx_busychk_multic(mii_dev_addr); + /* Write command to Switch indirect command register (read) */ + miiphy_write(name, mii_dev_addr, 0x0, + reg_ofs | (phy_adr << 5) | BIT10 | BIT12 | BIT15); + mv88e61xx_busychk_multic(mii_dev_addr); + /* Read data from Switch indirect data register */ + miiphy_read(name, mii_dev_addr, 0x1, (u16 *) & data); +} +#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */ + +static void mv88e61xx_vlaninit(struct mv88f61xx_config *swconfig, + u32 max_prtnum, u32 ports_ofs) +{ + u32 prt; + u16 reg; + char *name = swconfig->name; + u32 cpu_port = swconfig->cpuport; + u32 port_mask = swconfig->ports_enabled; + + /* be sure all ports are disabled */ + for (prt = 0; prt < max_prtnum; prt++) { + mv88e61xx_rd_phy(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, + &reg); + reg &= ~0x3; + mv88e61xx_wr_phy(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, + reg); + } + /* Set CPU port VID to 0x1 */ + mv88e61xx_rd_phy(name, (ports_ofs + cpu_port), MV88E61XX_PRT_VID_REG, + &reg); + reg &= ~0xfff; + reg |= 0x1; + mv88e61xx_wr_phy(name, (ports_ofs + cpu_port), MV88E61XX_PRT_VID_REG, + reg); + + /* Setting Port default priority for all ports to zero */ + for (prt = 0; prt < max_prtnum; prt++) { + mv88e61xx_rd_phy(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, + &reg); + reg &= ~0xc000; + mv88e61xx_wr_phy(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, + reg); + } + /* Setting VID and VID map for all ports except CPU port */ + for (prt = 0; prt < max_prtnum; prt++) { + /* only for enabled ports */ + if ((1 << prt) & port_mask) { + /* skip CPU port */ + if (prt == cpu_port) + continue; + + /* + * set Ports VLAN Mapping. + * port prt <--> cpu_port VLAN #prt+1. + */ + + mv88e61xx_rd_phy(name, ports_ofs + prt, + MV88E61XX_PRT_VID_REG, &reg); + reg &= ~0x0fff; + reg |= (prt + 1); + mv88e61xx_wr_phy(name, ports_ofs + prt, + MV88E61XX_PRT_VID_REG, reg); + + /* + * Set Vlan map table for all ports to send only to + * cpu_port + */ + mv88e61xx_rd_phy(name, ports_ofs + prt, + MV88E61XX_PRT_VMAP_REG, &reg); + reg &= ~((1 << max_prtnum) - 1); + reg |= (1 << cpu_port); + mv88e61xx_wr_phy(name, ports_ofs + prt, + MV88E61XX_PRT_VMAP_REG, reg); + } + } + /* Set Vlan map table for cpu_port to see all ports */ + mv88e61xx_rd_phy(name, (ports_ofs + cpu_port), MV88E61XX_PRT_VMAP_REG, + &reg); + reg &= ~((1 << max_prtnum) - 1); + reg |= port_mask & ~(1 << cpu_port); + mv88e61xx_wr_phy(name, (ports_ofs + cpu_port), MV88E61XX_PRT_VMAP_REG, + reg); + + /* + * enable only appropriate ports to forwarding mode + * and disable the others + */ + for (prt = 0; prt < max_prtnum; prt++) { + if ((1 << prt) & port_mask) { + mv88e61xx_rd_phy(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, &reg); + reg |= 0x3; + mv88e61xx_wr_phy(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, reg); + } else { + /* Disable port */ + mv88e61xx_rd_phy(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, &reg); + reg &= ~0x3; + mv88e61xx_wr_phy(name, ports_ofs + prt, + MV88E61XX_PRT_CTRL_REG, reg); + } + } +} + +/* + * Make sure SMIBusy bit cleared before another + * SMI operation can take place + */ +static int mv88361xx_busychk(char *name) +{ + u32 reg = 0; + u32 timeout = MV88E61XX_PHY_TIMEOUT; + do { + mv88e61xx_rd_phy(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, (u16 *) & reg); + if (timeout-- == 0) { + printf("SMI busy timeout\n"); + return -1; + } + } while (reg & BIT28); /* busy mask */ + return 0; +} + +/* + * Marvell 88E61XX Switch initialization + */ +int mv_switch_88e61xx_init(struct mv88f61xx_config *swconfig) +{ + u32 prt; + u16 reg; + char *idstr; + char *name = swconfig->name; + + if (miiphy_set_current_dev(name)) { + printf("%s failed\n", __FUNCTION__); + return -1; + } + + if (swconfig->mode != MV88F61XX_MODE_SW_MANAGEED) { + printf("Unsupported mode %s failed\n", __FUNCTION__); + return -1; + } + + if (swconfig->cpuport < 4) { + swconfig->cpuport = 5; + printf("Invalid cpu port config, using default port5\n"); + } + + mv88e61xx_rd_phy(name, MV88E61XX_PRT_OFST, PHY_PHYIDR2, &reg); + reg &= 0xfff0; + if (reg == 0x1610) + idstr = "88E6161"; + if (reg == 0x1650) + idstr = "88E6165"; + if (reg == 0x1210) { + idstr = "88E6123"; + swconfig->ports_enabled &= 0x023; /* ports 2,3,4 no available */ + } + + /* Init vlan */ + mv88e61xx_vlaninit(swconfig, MV88E61XX_MAX_PORTS_NUM, + MV88E61XX_PRT_OFST); + + if (swconfig->rgmii_delay == MV88F61XX_RGMII_DELAY_EN) { + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 9.5 of chip datasheet-02 + */ + mv88e61xx_wr_phy(name, MV88E61XX_PRT_OFST + 5, + MV88E61XX_RGMII_TIMECTRL_REG, 0x18); + mv88e61xx_wr_phy(name, MV88E61XX_PRT_OFST + 4, + MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7); + } + + for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) { + if (prt != swconfig->cpuport) { + /* Write Copper Specific control reg1 (0x14) for- + * Enable Phy power up + * Energy Detect on (sense&Xmit NLP Periodically + * reset other settings default + */ + mv88e61xx_wr_phy(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_DATA, 0x3360); + mv88e61xx_wr_phy(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, + (0x9410 | (prt << 5))); + + if (mv88361xx_busychk(name)) + return -1; + + /* Write PHY ctrl reg (0x0) to apply + * Phy reset (BIT15=low) + * reset other default values + */ + mv88e61xx_wr_phy(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_DATA, 0x1140); + mv88e61xx_wr_phy(name, MV88E61XX_GLB2REG_DEVADR, + MV88E61XX_PHY_CMD, + (0x9400 | (prt << 5))); + + if (mv88361xx_busychk(name)) + return -1; + } + + /*Program port state */ + mv88e61xx_rd_phy(name, MV88E61XX_PRT_OFST + prt, + MV88E61XX_PRT_CTRL_REG, &reg); + mv88e61xx_wr_phy(name, MV88E61XX_PRT_OFST + prt, + MV88E61XX_PRT_CTRL_REG, + reg | (swconfig->portstate & 0x03)); + } + + printf("%s Initialized on %s\n", idstr, name); + return 0; +} diff --git a/drivers/net/mv88e61xx.h b/drivers/net/mv88e61xx.h new file mode 100644 index 0000000..f1c86a6 --- /dev/null +++ b/drivers/net/mv88e61xx.h @@ -0,0 +1,73 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Prafulla Wadaskar <prafulla(a)marvell.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _MV88E61XX_H +#define _MV88E61XX_H + +#define PORT(_x) (1 << _x) +#define MV88E61XX_CPU_PORT 0x5 +#define MV88E61XX_MAX_PORTS_NUM 0x6 + +#define MV88E61XX_PHY_TIMEOUT 100000 + +#define MV88E61XX_PRT_STS_REG 0x1 +#define MV88E61XX_PRT_CTRL_REG 0x4 +#define MV88E61XX_PRT_VMAP_REG 0x6 +#define MV88E61XX_PRT_VID_REG 0x7 + +#define MV88E61XX_PRT_OFST 0x10 +#define MV88E61XX_PHY_CMD 0x18 +#define MV88E61XX_PHY_DATA 0x19 +#define MV88E61XX_RGMII_TIMECTRL_REG 0x1A +#define MV88E61XX_GLB2REG_DEVADR 0x1C + +/* constants for switch configuration */ +enum mv88f61xx_cfg_mode { + MV88F61XX_MODE_SW_MANAGEED, + MV88F61XX_MODE_SW_UNMANAGEED +}; + +enum mv88f61xx_cfg_rgmiid { + MV88F61XX_RGMII_DELAY_DIS, + MV88F61XX_RGMII_DELAY_EN +}; + +enum mv88f61xx_cfg_prtstt { + MV88E61XX_PORTSTT_DISABLED, + MV88E61XX_PORTSTT_BLOCKING, + MV88E61XX_PORTSTT_LEARNING, + MV88E61XX_PORTSTT_FORWARDING +}; + +/* switch configuration structure */ +struct mv88f61xx_config { + char *name; + enum mv88f61xx_cfg_mode mode; + enum mv88f61xx_cfg_rgmiid rgmii_delay; + enum mv88f61xx_cfg_prtstt portstate; + u32 ports_enabled; + u8 cpuport; +}; + +#endif /* _MV88E61XX_H */ -- 1.5.3.3

5 11

[U-Boot] Read-only env variables
by Joe Hershberger 15 Jan '13

15 Jan '13

Hi u-boot, I see u-boot supports readonly serial# and ethaddr, but I have a few other variables that I need to be read-only. I'm planning to implement a generic list of variables that cannot be changed or deleted. I'm interested to know what sort of specification people would find most appropriate. My current thought is to follow the same delimiter as the env itself, i.e. null separated list with double null terminator. This list would then be defined in the board config header. It also seems that you should be able to specify simple access rules for each variable name perhaps using "=<val>" after each var name where <val> could have constants (probably numbers for performance, but could be string literals) to define modes. Right now I'm thinking read-only, create-only, change-default, and change-only (i.e no delete) are the modes that make sense. I'm also interested if anyone would be opposed to simply using this new specification of readonly vars to implement the serial# and ethaddr protection. The CONFIG_HAS_UID is a bit odd... should that be available in general for read-only vars? Comments? Thanks, -Joe

10 123

[U-Boot] ERROR: CTL:TIMEOUT - USB porting issue for UBoot on S3C2450
by dongdaking 23 Nov '12

23 Nov '12

Hi, I am porting UBoot on S3C2450 and has an USB issue. Here is an error message: ERROR: CTL:TIMEOUT USB device not responding, giving up (status=20) 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found The problem seems submit_common_msg couldn't get description of USB flash memory device Could I have help? Please tell me if you had this issue before. Thank you for your helping Here is a log data usb start (Re)start USB... USB: INFO: aligned ghcca c3e4f900 DEBUG: USB HC reset_hc usb-smdk2450: ctrl = 0x9F ; DEBUG: OHCI controller usb-smdk2450 state DEBUG: control: 0x0000008f HCFS=operational IE PLE CBSR=3 DEBUG: cmdstatus: 0x00000000 SOC=0 DEBUG: intrstatus: 0x00000044 RHSC SF DEBUG: intrenable: 0x00000053 RHSC UE WDH SO DEBUG: hcca frame #0000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS scanning bus for devices... New Device 0 start 0st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0040 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:64/64 stat:0x0 start 1st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0040 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:64/64 stat:0x0 start 2st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 INFO: Root-Hub: adr: 0 cmd(8): 00000680 0100 0000 0040 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:64/64 stat:0x0 set address 1 usb_control_msg: request: 0x5, requesttype: 0x0 value 0x1 index 0x0 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000500 0001 0000 0000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x12 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/18 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0100 0000 0012 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:18/18 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x8 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/8 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0200 0000 0008 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:8/8 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x200 index 0x0 length 0x19 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/25 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0200 0000 0019 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:25/25 stat:0x0 get_conf_no 0 Result 25, wLength 25 if 0, ep 0 ##EP epmaxpacketin[1] = 2 set configuration 1 usb_control_msg: request: 0x9, requesttype: 0x0 value 0x1 index 0x0 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000900 0001 0000 0000 INFO: WR:status 0x10000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 new device strings: Mfr=0, Product=1, SerialNumber=0 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x300 index 0x0 length 0xFF INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0300 0000 00ff DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:255/255 stat:0x0 USB device number 1 default language ID 0x409 usb_control_msg: request: 0x6, requesttype: 0x80 value 0x301 index 0x409 length 0xFF INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/255 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000680 0301 0409 00ff DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:255/255 stat:0x0 Manufacturer Product OHCI Root Hub SerialNumber usb_control_msg: request: 0x6, requesttype: 0xA0 value 0x2900 index 0x0 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000006a0 2900 0000 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x6, requesttype: 0xA0 value 0x2900 index 0x0 length 0x9 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/9 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000006a0 2900 0000 0009 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:9/9 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA0 value 0x0 index 0x0 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a0 0000 0000 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x3, requesttype: 0x23 value 0x8 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0008 0001 0000 INFO: WR:portstatus[0] 0x100 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x3, requesttype: 0x23 value 0x8 index 0x2 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0008 0002 0000 INFO: WR:portstatus[1] 0x100 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00010101 CSC PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x1, requesttype: 0x23 value 0x10 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0010 0001 0000 INFO: WR:portstatus[0] 0x10000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x3, requesttype: 0x23 value 0x4 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0004 0001 0000 INFO: WR:portstatus[0] 0x10 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x1, requesttype: 0x23 value 0x14 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0014 0001 0000 INFO: WR:portstatus[0] 0x100000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000103 PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 New Device 1 start 0st usb_new_device usb_control_msg: request: 0x6, requesttype: 0x80 value 0x100 index 0x0 length 0x40 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: SUB URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x80000000 DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. DEBUG: % DEBUG: hc_interrupt: returning.. ERROR: hc_interrupt: returning.. ERROR: CTL:TIMEOUT DEBUG: submit_common_msg: TO status ff DEBUG: RET(ctlr) URB:[ 0] dev: 0,ep: 0-I,type:CTRL,len:0/64 stat:0x20 usb_new_device: 64 byte descr usb_control_msg: request: 0x3, requesttype: 0x23 value 0x4 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000323 0004 0001 0000 INFO: WR:portstatus[0] 0x10 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x1 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0001 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 usb_control_msg: request: 0x1, requesttype: 0x23 value 0x14 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0014 0001 0000 INFO: WR:portstatus[0] 0x100000 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000103 PPS PES CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 set address 2 usb_control_msg: request: 0x5, requesttype: 0x0 value 0x2 index 0x0 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 0,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 ERROR: submit_control_message: pipesize for pipe 80000000 is zero USB device not accepting new address (error=80000000) usb_control_msg: request: 0x1, requesttype: 0x23 value 0x1 index 0x1 length 0x0 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 00000123 0001 0001 0000 INFO: WR:portstatus[0] 0x1 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-O,type:CTRL,len:0/0 stat:0x0 usb_control_msg: request: 0x0, requesttype: 0xA3 value 0x0 index 0x2 length 0x4 INFO: submit_control_msg DEBUG: SUB URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 DEBUG: SUB(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:0/4 stat:0x80000000 INFO: Root-Hub: adr: 1 cmd(8): 000000a3 0000 0002 0004 DEBUG: roothub.a: 02001202 POTPGT=2 NOCP NPS NDP=2 DEBUG: roothub.b: 00000000 PPCM=0000 DR=0000 DEBUG: roothub.status: 00000000 DEBUG: roothub.portstatus [0] = 0x00000101 PPS CCS DEBUG: roothub.portstatus [1] = 0x00000100 PPS DEBUG: RET(rh) URB:[ 0] dev: 1,ep: 0-I,type:CTRL,len:4/4 stat:0x0 2 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found Thank you a lot. Best regards -- View this message in context: http://old.nabble.com/ERROR%3A-CTL%3ATIMEOUT---USB-porting-issue-for-UBoot-… Sent from the Uboot - Users mailing list archive at Nabble.com.

2 1

[U-Boot] fw_printenv is not working
by mateer 22 Oct '12

22 Oct '12

Hi, when i run fw_printenv , its not working..It shows:- fw_printenv: line 1: syntax error: "(" unexpected error... Let me tell you what i did... 1) i copy the u-boot source code from my colleague and copy in my hard disk. 2) After then i set the environment through commnads. the commands which i run are # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm distclean # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm omap3_evm_config # make CROSS_COMPILE=arm-none-linux-gnueabi- ARCH=arm 3) After then i go to /tools/env, where i configure the fw_env.config and then run make command. 4) After ruuning the command i got crc32.c and fw_printenv. 5)i copied the fw_printenv into the SD-Card and insert the card into the OMAP3EVM board. 6) after then when i use the command ./fw_printenv it throws the error fw_printenv: line 1: syntax error: "(" unexpected error.. Can u please help me what i have to do... I think i am doing something wrong... -- View this message in context: http://old.nabble.com/fw_printenv-is-not-working-tp29297562p29297562.html Sent from the Uboot - Users mailing list archive at Nabble.com.

4 3

[U-Boot] [PATCH] Prevent malloc with size 0
by Kostaras Nikolaos 17 Oct '12

17 Oct '12

In case malloc is invoked with requested size 0, this patch will prevent the execution of the allocation algorithm (because it corrupts the data structures) and will return 0 to the caller. Signed-off-by: Nikolaos Kostaras <nkost(a)intracomdefense.com> --- common/dlmalloc.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/common/dlmalloc.c b/common/dlmalloc.c index fce7a76..d9e3ea9 100644 --- a/common/dlmalloc.c +++ b/common/dlmalloc.c @@ -2182,7 +2182,7 @@ Void_t* mALLOc(bytes) size_t bytes; return 0; } - if ((long)bytes < 0) return 0; + if ((long)bytes <= 0) return 0; nb = request2size(bytes); /* padded request size; */ -- 1.6.4.4

9 74

[U-Boot] [PATCH] [U-BOOT] Zoom2: Ethernet: Enabling LAN9221 chip and CMD_NET.
by Aldo Brett Cedillo Martinez 06 Sep '12

06 Sep '12

Configures GPMC, adds macros to enable net commands, and adds proper initialization to board_eth_init function. I have a similar patch to enable ethernet in zoom3 after initial support patch. Signed-off-by: Aldo Brett Cedillo Martinez <aldo.cedillo(a)ti.com> --- board/logicpd/zoom2/zoom2.c | 21 +++++++++++++++++++++ include/configs/omap3_zoom2.h | 10 +++++++++- 2 files changed, 30 insertions(+), 1 deletions(-) diff --git a/board/logicpd/zoom2/zoom2.c b/board/logicpd/zoom2/zoom2.c index e9f6625..54d3e9f 100644 --- a/board/logicpd/zoom2/zoom2.c +++ b/board/logicpd/zoom2/zoom2.c @@ -60,6 +60,16 @@ static u32 gpmc_serial_TL16CP754C[GPMC_MAX_REG] = { 0x1D0904C4, 0 }; +/* Ethernet GPMC configuration */ +static u32 gpmc_eth[GPMC_MAX_REG] = { + NET_GPMC_CONFIG1, + NET_GPMC_CONFIG2, + NET_GPMC_CONFIG3, + NET_GPMC_CONFIG4, + NET_GPMC_CONFIG5, + NET_GPMC_CONFIG6, 0 +}; + /* Used to track the revision of the board */ static zoom2_revision revision = ZOOM2_REVISION_UNKNOWN; @@ -130,6 +140,12 @@ int board_init (void) enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[3], SERIAL_TL16CP754C_BASE, GPMC_SIZE_16M); +#ifdef CONFIG_CMD_NET + gpmc_config = gpmc_eth; + enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[7], + CONFIG_SMC911X_BASE, GPMC_SIZE_16M); +#endif /* (CONFIG_CMD_NET) */ + /* board id for Linux */ gd->bd->bi_arch_number = MACH_TYPE_OMAP_ZOOM2; /* boot param addr */ @@ -186,6 +202,11 @@ int board_eth_init(bd_t *bis) #ifdef CONFIG_LAN91C96 rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE); #endif + +#ifdef CONFIG_SMC911X + rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); +#endif + return rc; } #endif diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h index eef95fe..c66d571 100644 --- a/include/configs/omap3_zoom2.h +++ b/include/configs/omap3_zoom2.h @@ -154,7 +154,7 @@ #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ #undef CONFIG_CMD_IMI /* iminfo */ #undef CONFIG_CMD_IMLS /* List all found images */ -#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ #undef CONFIG_CMD_NFS /* NFS support */ #define CONFIG_SYS_NO_FLASH @@ -165,6 +165,14 @@ #define CONFIG_SYS_I2C_BUS_SELECT 1 #define CONFIG_DRIVER_OMAP34XX_I2C 1 +/* Ethernet */ +#ifdef CONFIG_CMD_NET +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE 0x2C000000 +#endif /* (CONFIG_CMD_NET) */ + /* * TWL4030 */ -- 1.6.3.3

3 3