October 2010 - U-Boot

Re: [U-Boot] SD card on the GuruPlug
by ludo＠gnu.org 04 Oct '10

04 Oct '10

Hi, Prafulla Wadaskar <prafulla(a)marvell.com> writes: > On guruplug+ if the uSD cards are inserted on both the slots (internal and external) > The USB storage does not gets detected. Yes, I figured out. I’m preparing a patch that adds support for multi-LUN USB mass storage devices. Thanks, Ludo’.

1 0

[U-Boot] Would somebody block this please?
by Sergey Kubushyn 04 Oct '10

04 Oct '10

It is already 5th or more same spam email in a row. Does anybody care? --- ****************************************************************** * KSI@home KOI8 Net < > The impossible we do immediately. * * Las Vegas NV, USA < > Miracles require 24-hour notice. * ****************************************************************** ---------- Forwarded message ---------- Date: Fri, 1 Oct 2010 19:48:28 From: Kara Duggan <klduggan(a)eagle.fgcu.edu> To: undisclosed-recipients: ; Subject: [U-Boot] Guaranteed loan offer**APPLY NOW**contact via email**bt48hrsfinancerdesk123(a)gmail.com** We are currently giving out loans to any part of the world at 2% interest rate. If interested, send your name, Resident country and Phone number to Mr. Bernard Thompson with the email address bellow Email: 48hrsfinancerdesk112(a)gmail.com or call: +447024053959 Regards B&T 48HRS FINANCE LOAN _______________________________________________ U-Boot mailing list U-Boot(a)lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot

2 1

[U-Boot] [PATCH v1] ppc44x: config GPIOs for USB on canyonlands board
by Rupjyoti Sarmah 04 Oct '10

04 Oct '10

The GPIO 16 and 19 reconfiguration should be done once USB is initialized. So moved the reconfiguration to the USB init function. Signed-off-by: Rupjyoti Sarmah <rsarmah(a)apm.com> --- board/amcc/canyonlands/canyonlands.c | 23 +++++++++++++---------- 1 files changed, 13 insertions(+), 10 deletions(-) diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index 158f7bb..09adc3b 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -195,16 +195,6 @@ int board_early_init_f(void) mtdcr(AHB_TOP, 0x8000004B); mtdcr(AHB_BOT, 0x8000004B); - if (pvr_460ex()) { - /* - * Configure USB-STP pins as alternate and not GPIO - * It seems to be neccessary to configure the STP pins as GPIO - * input at powerup (perhaps while USB reset is asserted). So - * we configure those pins to their "real" function now. - */ - gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); - gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); - } #endif return 0; @@ -222,6 +212,15 @@ int usb_board_init(void) val &= ~(BCSR_USBCTRL_OTG_RST | BCSR_USBCTRL_HOST_RST); out_8(&bcsr_data->usb_ctrl, val); + /* + * Configure USB-STP pins as alternate and not GPIO + * It seems to be neccessary to configure the STP pins as GPIO + * input at powerup (perhaps while USB reset is asserted). So + * we configure those pins to their "real" function now. + */ + gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); + gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1); + return 0; } @@ -236,6 +235,10 @@ int usb_board_stop(void) val |= (BCSR_USBCTRL_OTG_RST | BCSR_USBCTRL_HOST_RST); out_8(&bcsr_data->usb_ctrl, val); + /* Reconfigure USB-STP pins as input */ + gpio_config(16, GPIO_IN , GPIO_SEL, GPIO_OUT_0); + gpio_config(19, GPIO_IN , GPIO_SEL, GPIO_OUT_0); + return 0; } -- 1.5.6.3

2 1

[U-Boot] [PATCH] ppc4xx: Remove some testing hacks from ppc4xx.h
by Stefan Roese 04 Oct '10

04 Oct '10

I accidentally left these hacks in the code while doing the big header cleanup. Let's remove it now. Signed-off-by: Stefan Roese <sr(a)denx.de> --- arch/powerpc/include/asm/ppc4xx.h | 17 ----------------- 1 files changed, 0 insertions(+), 17 deletions(-) diff --git a/arch/powerpc/include/asm/ppc4xx.h b/arch/powerpc/include/asm/ppc4xx.h index 87a16ec..ff6034e 100644 --- a/arch/powerpc/include/asm/ppc4xx.h +++ b/arch/powerpc/include/asm/ppc4xx.h @@ -82,7 +82,6 @@ /* * Configure which SDRAM/DDR/DDR2 controller is equipped */ -// test-only: what to do with these??? #if defined(CONFIG_AP1000) || defined(CONFIG_ML2) #define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */ #endif @@ -202,22 +201,6 @@ #define GPT0_DCT0 0x00000110 #define GPT0_DCIS 0x0000011C -#if 0 // test-only -/* - * All PPC4xx share the same NS16550 UART(s). Only base addresses - * may differ. We define here the integration of the common NS16550 - * driver for all PPC4xx SoC's. The board config header must specify - * on which UART the console should be located via CONFIG_CONS_INDEX. - */ -#if 0 /* test-only */ -#define CONFIG_SERIAL_MULTI -#endif -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#endif - #if defined(CONFIG_440) #include <asm/ppc440.h> #else -- 1.7.3

1 1

[U-Boot] [PATCH] ppc4xx: Use common ns16550 functions in 4xx UART POST driver
by Stefan Roese 04 Oct '10

04 Oct '10

This patch changes the PPC4xx POST UART driver to use the common NS16550 functions for receiving and sending. Additionally the local function for SoC divisor setup are removed. Instead the functions from arch/powerpc/cpu/ppc4xx/4xx_uart.c are used. This removes code duplication. Also the common CONFIG_SYS_NS16550_COMx defines are now used to describe the POST UART's. And a compile breakage is fixed, introduced by a git merge of the ppc4xx/next branch into master. Now "ppc4xx.h" is moved to "asm/ppc4xx.h". Fixed as well with this patch. Signed-off-by: Stefan Roese <sr(a)denx.de> --- include/configs/hcu4.h | 2 +- include/configs/hcu5.h | 2 +- include/configs/kilauea.h | 3 +- include/configs/lwmon5.h | 3 +- include/configs/makalu.h | 3 +- include/configs/mcu25.h | 2 +- include/configs/zeus.h | 2 +- post/cpu/ppc4xx/uart.c | 302 ++++----------------------------------------- 8 files changed, 32 insertions(+), 287 deletions(-) diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h index 26992e7..68bf998 100644 --- a/include/configs/hcu4.h +++ b/include/configs/hcu4.h @@ -191,7 +191,7 @@ CONFIG_SYS_POST_ETHER | \ CONFIG_SYS_POST_SPR) -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #undef CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h index f2ab50c..5aa304d 100644 --- a/include/configs/hcu5.h +++ b/include/configs/hcu5.h @@ -208,7 +208,7 @@ CONFIG_SYS_POST_ETHER | \ CONFIG_SYS_POST_SPR) -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 37eaf8f..612a0fe 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -457,7 +457,8 @@ CONFIG_SYS_POST_UART) /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } #define CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 2349583..4a3b1dc 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -185,7 +185,8 @@ CONFIG_SYS_POST_BSPEC5) /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE { UART0_BASE, UART1_BASE } +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } #define CONFIG_POST_WATCHDOG { \ "Watchdog timer test", \ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 905c719..80163d4 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -264,7 +264,8 @@ CONFIG_SYS_POST_UART) /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } #define CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ diff --git a/include/configs/mcu25.h b/include/configs/mcu25.h index 3e04cfe..8dd87cb 100644 --- a/include/configs/mcu25.h +++ b/include/configs/mcu25.h @@ -192,7 +192,7 @@ CONFIG_SYS_POST_ETHER | \ CONFIG_SYS_POST_SPR) -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #undef CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/zeus.h b/include/configs/zeus.h index aa250cc..06d4526 100644 --- a/include/configs/zeus.h +++ b/include/configs/zeus.h @@ -94,7 +94,7 @@ #define CONFIG_SYS_POST_ETHER_EXT_LOOPBACK /* eth POST using ext loopack connector */ /* Define here the base-addresses of the UARTs to test in POST */ -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE} +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 } #define CONFIG_LOGBUFFER #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ diff --git a/post/cpu/ppc4xx/uart.c b/post/cpu/ppc4xx/uart.c index 6b61cc1..d768956 100644 --- a/post/cpu/ppc4xx/uart.c +++ b/post/cpu/ppc4xx/uart.c @@ -26,9 +26,10 @@ */ #include <common.h> -#include <ppc4xx.h> +#include <asm/ppc4xx.h> #include <ns16550.h> #include <asm/io.h> +#include <serial.h> /* * UART test @@ -46,299 +47,40 @@ * be overridden in the board config file */ #ifndef CONFIG_SYS_POST_UART_TABLE -#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE, UART2_BASE, UART3_BASE} -#endif - -#include <asm/processor.h> -#include <serial.h> - -#if defined(CONFIG_440) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) -#define UART0_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000300 -#define UART1_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000400 -#define UART2_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000500 -#define UART3_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000600 -#else -#define UART0_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000200 -#define UART1_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000300 -#endif - -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) -#define UART2_BASE CONFIG_SYS_PERIPHERAL_BASE + 0x00000600 -#endif - -#if defined(CONFIG_440GP) -#define CR0_MASK 0x3fff0000 -#define CR0_EXTCLK_ENA 0x00600000 -#define CR0_UDIV_POS 16 -#define UDIV_SUBTRACT 1 -#define UART0_SDR CPC0_CR0 -#define MFREG(a, d) d = mfdcr(a) -#define MTREG(a, d) mtdcr(a, d) -#else /* #if defined(CONFIG_440GP) */ -/* all other 440 PPC's access clock divider via sdr register */ -#define CR0_MASK 0xdfffffff -#define CR0_EXTCLK_ENA 0x00800000 -#define CR0_UDIV_POS 0 -#define UDIV_SUBTRACT 0 -#define UART0_SDR SDR0_UART0 -#define UART1_SDR SDR0_UART1 -#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ - defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) -#define UART2_SDR SDR0_UART2 -#endif -#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ - defined(CONFIG_440GR) || defined(CONFIG_440GRX) -#define UART3_SDR SDR0_UART3 -#endif -#define MFREG(a, d) mfsdr(a, d) -#define MTREG(a, d) mtsdr(a, d) -#endif /* #if defined(CONFIG_440GP) */ -#elif defined(CONFIG_405EP) || defined(CONFIG_405EZ) -#define UART0_BASE 0xef600300 -#define UART1_BASE 0xef600400 -#define UCR0_MASK 0x0000007f -#define UCR1_MASK 0x00007f00 -#define UCR0_UDIV_POS 0 -#define UCR1_UDIV_POS 8 -#define UDIV_MAX 127 -#elif defined(CONFIG_405EX) -#define UART0_BASE 0xef600200 -#define UART1_BASE 0xef600300 -#define CR0_MASK 0x000000ff -#define CR0_EXTCLK_ENA 0x00800000 -#define CR0_UDIV_POS 0 -#define UDIV_SUBTRACT 0 -#define UART0_SDR SDR0_UART0 -#define UART1_SDR SDR0_UART1 -#define MFREG(a, d) mfsdr(a, d) -#define MTREG(a, d) mtsdr(a, d) -#else /* CONFIG_405GP || CONFIG_405CR */ -#define UART0_BASE 0xef600300 -#define UART1_BASE 0xef600400 -#define CR0_MASK 0x00001fff -#define CR0_EXTCLK_ENA 0x000000c0 -#define CR0_UDIV_POS 1 -#define UDIV_MAX 32 +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2, CONFIG_SYS_NS16550_COM3, \ + CONFIG_SYS_NS16550_COM4 } #endif DECLARE_GLOBAL_DATA_PTR; -static void uart_post_init_common(struct NS16550 *com_port, unsigned short bdiv) -{ - volatile char val; - - out_8(&com_port->lcr, 0x80); /* set DLAB bit */ - out_8(&com_port->dll, bdiv); /* set baudrate divisor */ - out_8(&com_port->dlm, bdiv >> 8); /* set baudrate divisor */ - out_8(&com_port->lcr, 0x03); /* clear DLAB; set 8 bits, no parity */ - out_8(&com_port->fcr, 0x00); /* disable FIFO */ - out_8(&com_port->mcr, 0x10); /* enable loopback mode */ - val = in_8(&com_port->lsr); /* clear line status */ - val = in_8(&com_port->rbr); /* read receive buffer */ - out_8(&com_port->scr, 0x00); /* set scratchpad */ - out_8(&com_port->ier, 0x00); /* set interrupt enable reg */ -} - -#if defined(CONFIG_440) || defined(CONFIG_405EX) -#if !defined(CONFIG_SYS_EXT_SERIAL_CLOCK) -static void serial_divs (int baudrate, unsigned long *pudiv, - unsigned short *pbdiv) -{ - sys_info_t sysinfo; - unsigned long div; /* total divisor udiv * bdiv */ - unsigned long umin; /* minimum udiv */ - unsigned short diff; /* smallest diff */ - unsigned long udiv; /* best udiv */ - unsigned short idiff; /* current diff */ - unsigned short ibdiv; /* current bdiv */ - unsigned long i; - unsigned long est; /* current estimate */ - - get_sys_info(&sysinfo); - - udiv = 32; /* Assume lowest possible serial clk */ - div = sysinfo.freqPLB / (16 * baudrate); /* total divisor */ - umin = sysinfo.pllOpbDiv << 1; /* 2 x OPB divisor */ - diff = 32; /* highest possible */ - - /* i is the test udiv value -- start with the largest - * possible (32) to minimize serial clock and constrain - * search to umin. - */ - for (i = 32; i > umin; i--) { - ibdiv = div / i; - est = i * ibdiv; - idiff = (est > div) ? (est-div) : (div-est); - if (idiff == 0) { - udiv = i; - break; /* can't do better */ - } else if (idiff < diff) { - udiv = i; /* best so far */ - diff = idiff; /* update lowest diff*/ - } - } - - *pudiv = udiv; - *pbdiv = div / udiv; -} -#endif - -static int uart_post_init (struct NS16550 *com_port) +static int test_ctlr (struct NS16550 *com_port, int index) { - unsigned long reg = 0; - unsigned long udiv; - unsigned short bdiv; -#ifdef CONFIG_SYS_EXT_SERIAL_CLOCK - unsigned long tmp; -#endif + int res = -1; + char test_str[] = "*** UART Test String ***\r\n"; int i; + int divisor; - for (i = 0; i < 3500; i++) { - if (in_8(&com_port->lsr) & UART_LSR_THRE) - break; - udelay (100); - } - MFREG(UART0_SDR, reg); - reg &= ~CR0_MASK; - -#ifdef CONFIG_SYS_EXT_SERIAL_CLOCK - reg |= CR0_EXTCLK_ENA; - udiv = 1; - tmp = gd->baudrate * 16; - bdiv = (CONFIG_SYS_EXT_SERIAL_CLOCK + tmp / 2) / tmp; -#else - /* For 440, the cpu clock is on divider chain A, UART on divider - * chain B ... so cpu clock is irrelevant. Get the "optimized" - * values that are subject to the 1/2 opb clock constraint - */ - serial_divs (gd->baudrate, &udiv, &bdiv); -#endif - - reg |= (udiv - UDIV_SUBTRACT) << CR0_UDIV_POS; /* set the UART divisor */ + divisor = (get_serial_clock() + (gd->baudrate * (16 / 2))) / + (16 * gd->baudrate); + NS16550_init(com_port, divisor); /* - * Configure input clock to baudrate generator for all - * available serial ports here + * Set internal loopback mode in UART */ - MTREG(UART0_SDR, reg); -#if defined(UART1_SDR) - MTREG(UART1_SDR, reg); -#endif -#if defined(UART2_SDR) - MTREG(UART2_SDR, reg); -#endif -#if defined(UART3_SDR) - MTREG(UART3_SDR, reg); -#endif - - uart_post_init_common(com_port, bdiv); - - return 0; -} - -#else /* CONFIG_440 */ - -static int uart_post_init (struct NS16550 *com_port) -{ - unsigned long reg; - unsigned long tmp; - unsigned long clk; - unsigned long udiv; - unsigned short bdiv; - int i; - - for (i = 0; i < 3500; i++) { - if (in_8(&com_port->lsr) & UART_LSR_THRE) - break; - udelay (100); - } - -#if defined(CONFIG_405EZ) - serial_divs(gd->baudrate, &udiv, &bdiv); - clk = tmp = reg = 0; -#else -#ifdef CONFIG_405EP - reg = mfdcr(CPC0_UCR) & ~(UCR0_MASK | UCR1_MASK); - clk = gd->cpu_clk; - tmp = CONFIG_SYS_BASE_BAUD * 16; - udiv = (clk + tmp / 2) / tmp; - if (udiv > UDIV_MAX) /* max. n bits for udiv */ - udiv = UDIV_MAX; - reg |= (udiv) << UCR0_UDIV_POS; /* set the UART divisor */ - reg |= (udiv) << UCR1_UDIV_POS; /* set the UART divisor */ - mtdcr (CPC0_UCR, reg); -#else /* CONFIG_405EP */ - reg = mfdcr(CPC0_CR0) & ~CR0_MASK; -#ifdef CONFIG_SYS_EXT_SERIAL_CLOCK - clk = CONFIG_SYS_EXT_SERIAL_CLOCK; - udiv = 1; - reg |= CR0_EXTCLK_ENA; -#else - clk = gd->cpu_clk; -#ifdef CONFIG_SYS_405_UART_ERRATA_59 - udiv = 31; /* Errata 59: stuck at 31 */ -#else - tmp = CONFIG_SYS_BASE_BAUD * 16; - udiv = (clk + tmp / 2) / tmp; - if (udiv > UDIV_MAX) /* max. n bits for udiv */ - udiv = UDIV_MAX; -#endif -#endif - reg |= (udiv - 1) << CR0_UDIV_POS; /* set the UART divisor */ - mtdcr (CPC0_CR0, reg); -#endif /* CONFIG_405EP */ - tmp = gd->baudrate * udiv * 16; - bdiv = (clk + tmp / 2) / tmp; -#endif /* CONFIG_405EZ */ - - uart_post_init_common(com_port, bdiv); + out_8(&com_port->mcr, in_8(&com_port->mcr) | UART_MCR_LOOP); - return 0; -} -#endif /* CONFIG_440 */ - -static void uart_post_putc (struct NS16550 *com_port, char c) -{ - int i; - - out_8(&com_port->thr, c); /* put character out */ - - /* Wait for transfer completion */ - for (i = 0; i < 3500; i++) { - if (in_8(&com_port->lsr) & UART_LSR_THRE) - break; - udelay (100); - } -} - -static int uart_post_getc (struct NS16550 *com_port) -{ - int i; - - /* Wait for character available */ - for (i = 0; i < 3500; i++) { - if (in_8(&com_port->lsr) & UART_LSR_DR) - break; - udelay (100); - } - - return 0xff & in_8(&com_port->rbr); -} - -static int test_ctlr (struct NS16550 *com_port, int index) -{ - int res = -1; - char test_str[] = "*** UART Test String ***\r\n"; - int i; + /* Reset FIFOs */ + out_8(&com_port->fcr, UART_FCR_RXSR | UART_FCR_TXSR); + udelay(100); - uart_post_init (com_port); + /* Flush RX-FIFO */ + while (NS16550_tstc(com_port)) + NS16550_getc(com_port); for (i = 0; i < sizeof (test_str) - 1; i++) { - uart_post_putc (com_port, test_str[i]); - if (uart_post_getc (com_port) != test_str[i]) + NS16550_putc(com_port, test_str[i]); + if (NS16550_getc(com_port) != test_str[i]) goto done; } res = 0; -- 1.7.3

1 1

[U-Boot] [PATCH] ppc4xx: Small whitespace cleanup in canyonlands.c
by Stefan Roese 04 Oct '10

04 Oct '10

Signed-off-by: Stefan Roese <sr(a)denx.de> --- board/amcc/canyonlands/canyonlands.c | 20 ++++++++++---------- 1 files changed, 10 insertions(+), 10 deletions(-) diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index b26cadb..a30d4f4 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -34,16 +34,16 @@ extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH ch DECLARE_GLOBAL_DATA_PTR; - struct board_bcsr { - u8 board_id; - u8 cpld_rev; - u8 led_user; - u8 board_status; - u8 reset_ctrl; - u8 flash_ctrl; - u8 eth_ctrl; - u8 usb_ctrl; - u8 irq_ctrl; +struct board_bcsr { + u8 board_id; + u8 cpld_rev; + u8 led_user; + u8 board_status; + u8 reset_ctrl; + u8 flash_ctrl; + u8 eth_ctrl; + u8 usb_ctrl; + u8 irq_ctrl; }; #define BOARD_CANYONLANDS_PCIE 1 -- 1.7.3

1 1

[U-Boot] [PATCH] ppc4xx/fdt/flash: Fix bug in fdt_fixup_nor_flash_node()
by Stefan Roese 04 Oct '10

04 Oct '10

This patch fixes a bug in fdt_fixup_nor_flash_node() when the reg property has multiple reg tuples, like: reg = <0 0x00000000 0x04000000 0 0x04000000 0x04000000>; In this case this function did not update the reg property correctly. Signed-off-by: Stefan Roese <sr(a)denx.de> --- common/fdt_support.c | 17 ++++++++++------- 1 files changed, 10 insertions(+), 7 deletions(-) diff --git a/common/fdt_support.c b/common/fdt_support.c index 6f32e3f..0ed6e77 100644 --- a/common/fdt_support.c +++ b/common/fdt_support.c @@ -620,7 +620,7 @@ int fdt_fixup_nor_flash_size(void *blob) int off; int len; struct fdt_property *prop; - u32 *reg; + u32 *reg, *reg2; int i; for (i = 0; i < 2; i++) { @@ -640,18 +640,21 @@ int fdt_fixup_nor_flash_size(void *blob) * There might be multiple reg-tuples, * so loop through them all */ - len /= tuple_size; - reg = (u32 *)&prop->data[0]; - for (idx = 0; idx < len; idx++) { + reg = reg2 = (u32 *)&prop->data[0]; + for (idx = 0; idx < (len / tuple_size); idx++) { /* * Update size in reg property */ reg[2] = flash_get_bank_size(reg[0], idx); - fdt_setprop(blob, off, "reg", reg, - tuple_size); - reg += tuple_size; + + /* + * Point to next reg tuple + */ + reg += 3; } + + fdt_setprop(blob, off, "reg", reg2, len); } /* Move to next compatible node */ -- 1.7.3

1 1

[U-Boot] [PATCH] ppc4xx: Add defines for COM3 & COM4 (UART2 & UART3) on 440EPx/GRx
by Stefan Roese 04 Oct '10

04 Oct '10

Signed-off-by: Stefan Roese <sr(a)denx.de> --- arch/powerpc/include/asm/ppc440epx_grx.h | 2 ++ 1 files changed, 2 insertions(+), 0 deletions(-) diff --git a/arch/powerpc/include/asm/ppc440epx_grx.h b/arch/powerpc/include/asm/ppc440epx_grx.h index 252f35b..6c21472 100644 --- a/arch/powerpc/include/asm/ppc440epx_grx.h +++ b/arch/powerpc/include/asm/ppc440epx_grx.h @@ -36,6 +36,8 @@ #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_PERIPHERAL_BASE + 0x0300) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_PERIPHERAL_BASE + 0x0400) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_PERIPHERAL_BASE + 0x0500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_PERIPHERAL_BASE + 0x0600) #define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x0b00) #define GPIO1_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x0c00) -- 1.7.3

1 1

[U-Boot] [PATCH] ppc4xx: Big lwmon5 board support rework/update
by Stefan Roese 04 Oct '10

04 Oct '10

From: Sascha Laue <sascha.laue(a)liebherr.com> This patch brings the lwmon5 board support up-to-date. Here a summary of the changes: lwmon5 board port related: - GPIO's changed to control the LSB transmitter - Reset USB PHY's upon power-up - Enable CAN upon power-up - USB init error workaround (errata CHIP_6) - EBC: Enable burstmode and modify the timings for the GDC memory - EBC: Speed up NOR flash timings lwmon5 board POST related: - Add FPGA memory test - Add GDC memory test - DSP POST reworked - SYSMON POST: Fix handling of negative temperatures - Add output for sysmon1 POST - HW-watchdog min. time test reworked Additionally some coding-style changes were done. Signed-off-by: Sascha Laue <sascha.laue(a)liebherr.com> Signed-off-by: Stefan Roese <sr(a)denx.de> --- board/lwmon5/kbd.c | 45 ++++++ board/lwmon5/lwmon5.c | 249 ++++++++++++++++++++++------------ include/configs/lwmon5.h | 283 ++++++++++++++++++++++----------------- post/board/lwmon5/dsp.c | 21 +++- post/board/lwmon5/dspic.c | 56 +++++--- post/board/lwmon5/fpga.c | 308 +++++++++++++++++++++++++++++++++++------ post/board/lwmon5/gdc.c | 308 ++++++++++++++++++++++++++++++++++++++++-- post/board/lwmon5/sysmon.c | 160 ++++++++++++++--------- post/board/lwmon5/watchdog.c | 19 ++- 9 files changed, 1090 insertions(+), 359 deletions(-) diff --git a/board/lwmon5/kbd.c b/board/lwmon5/kbd.c index 0e26b89..5231c7a 100644 --- a/board/lwmon5/kbd.c +++ b/board/lwmon5/kbd.c @@ -45,6 +45,10 @@ static int compare_magic (uchar *kbd_data, uchar *str); /*--------------------- Local macros and constants --------------------*/ #define _NOT_USED_ 0xFFFFFFFF +/*------------------------- dspic io expander -----------------------*/ +#define DSPIC_PON_STATUS_REG 0x80A +#define DSPIC_PON_INV_STATUS_REG 0x80C +#define DSPIC_PON_KEY_REG 0x810 /*------------------------- Keyboard controller -----------------------*/ /* command codes */ #define KEYBD_CMD_READ_KEYS 0x01 @@ -75,6 +79,7 @@ static int compare_magic (uchar *kbd_data, uchar *str); /* maximum number of "magic" key codes that can be assigned */ static uchar kbd_addr = CONFIG_SYS_I2C_KEYBD_ADDR; +static uchar dspic_addr = CONFIG_SYS_I2C_DSPIC_IO_ADDR; static uchar *key_match (uchar *); @@ -167,6 +172,23 @@ static void kbd_init (void) } } + +/* Read a register from the dsPIC. */ +int _dspic_read(ushort reg, ushort *data) +{ + uchar buf[sizeof(*data)]; + int rval; + + if (i2c_read(dspic_addr, reg, 2, buf, 2)) + return -1; + + rval = i2c_read(dspic_addr, reg, sizeof(reg), buf, sizeof(*data)); + *data = (buf[0] << 8) | buf[1]; + + return rval; +} + + /*********************************************************************** F* Function: int misc_init_r (void) P*A*Z* * @@ -197,6 +219,7 @@ int misc_init_r_kbd (void) uchar kbd_init_status = gd->kbd_status >> 8; uchar kbd_status = gd->kbd_status; uchar val; + ushort data, inv_data; char *str; int i; @@ -231,9 +254,31 @@ int misc_init_r_kbd (void) i2c_write (kbd_addr, 0, 0, &val, 1); i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN); + /* read out start key from bse01 received via can */ + _dspic_read(DSPIC_PON_STATUS_REG, &data); + /* check highbyte from status register */ + if (data > 0xFF) { + _dspic_read(DSPIC_PON_INV_STATUS_REG, &inv_data); + + /* check inverse data */ + if ((data+inv_data) == 0xFFFF) { + /* don't overwrite local key */ + if (kbd_data[1] == 0) { + /* read key value */ + _dspic_read(DSPIC_PON_KEY_REG, &data); + str = (char *)&data; + /* swap bytes */ + kbd_data[1] = str[1]; + kbd_data[2] = str[0]; + printf("CAN received startkey: 0x%X\n", data); + } + } + } + for (i = 0; i < KEYBD_DATALEN; ++i) { sprintf (keybd_env + i + i, "%02X", kbd_data[i]); } + setenv ("keybd", keybd_env); str = strdup ((char *)key_match (kbd_data)); /* decode keys */ diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c index 9622b70..dd275bf 100644 --- a/board/lwmon5/lwmon5.c +++ b/board/lwmon5/lwmon5.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2010 * Stefan Roese, DENX Software Engineering, sr(a)denx.de. * * This program is free software; you can redistribute it and/or @@ -24,10 +24,13 @@ #include <asm/processor.h> #include <asm/ppc4xx-gpio.h> #include <asm/io.h> +#include <post.h> +#include <flash.h> +#include <mtd/cfi_flash.h> DECLARE_GLOBAL_DATA_PTR; -extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ +static phys_addr_t lwmon5_cfi_flash_bank_addr[2] = CONFIG_SYS_FLASH_BANKS_LIST; ulong flash_get_size(ulong base, int banknum); int misc_init_r_kbd(void); @@ -97,16 +100,18 @@ int board_early_init_f(void) gpio_write_bit(CONFIG_SYS_GPIO_FLASH_WP, 1); #if CONFIG_POST & CONFIG_SYS_POST_BSPEC1 - gpio_write_bit(CONFIG_SYS_GPIO_HIGHSIDE, 1); + /* enable the LSB transmitter */ + gpio_write_bit(CONFIG_SYS_GPIO_LSB_ENABLE, 1); + /* enable the CAN transmitter */ + gpio_write_bit(CONFIG_SYS_GPIO_CAN_ENABLE, 1); reg = 0; /* reuse as counter */ out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR, in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) & ~CONFIG_SYS_DSPIC_TEST_MASK); - while (!gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY) && reg++ < 1000) { + while (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY) && reg++ < 1000) { udelay(1000); } - gpio_write_bit(CONFIG_SYS_GPIO_HIGHSIDE, 0); if (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY)) { /* set "boot error" flag */ out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR, @@ -135,9 +140,61 @@ int board_early_init_f(void) return 0; } -/*---------------------------------------------------------------------------+ - | misc_init_r. - +---------------------------------------------------------------------------*/ +/* + * Override weak default with board specific version + */ +phys_addr_t cfi_flash_bank_addr(int bank) +{ + return lwmon5_cfi_flash_bank_addr[bank]; +} + +/* + * Override the weak default mapping function with a board specific one + */ +u32 flash_get_bank_size(int cs, int idx) +{ + return flash_info[idx].size; +} + +int board_early_init_r(void) +{ + u32 val0, val1; + + /* + * lwmon5 is manufactured in 2 different board versions: + * The lwmon5a board has 64MiB NOR flash instead of the + * 128MiB of the original lwmon5. Unfortunately the CFI driver + * will report 2 banks of 64MiB even for the smaller flash + * chip, since the bank is mirrored. To fix this, we bring + * one bank into CFI query mode and read its response. This + * enables us to detect the real number of flash devices/ + * banks which will be used later on by the common CFI driver. + */ + + /* Put bank 0 into CFI command mode and read */ + out_be32((void *)CONFIG_SYS_FLASH0, 0x00980098); + val0 = in_be32((void *)CONFIG_SYS_FLASH0 + FLASH_OFFSET_CFI_RESP); + val1 = in_be32((void *)CONFIG_SYS_FLASH1 + FLASH_OFFSET_CFI_RESP); + + /* Reset flash again out of query mode */ + out_be32((void *)CONFIG_SYS_FLASH0, 0x00f000f0); + + /* When not identical, we have 2 different flash devices/banks */ + if (val0 != val1) + return 0; + + /* + * Now we're sure that we're running on a LWMON5a board with + * only 64MiB NOR flash in one bank: + * + * Set flash base address and bank count for CFI driver probing. + */ + cfi_flash_num_flash_banks = 1; + lwmon5_cfi_flash_bank_addr[0] = CONFIG_SYS_FLASH0; + + return 0; +} + int misc_init_r(void) { u32 pbcr; @@ -145,7 +202,7 @@ int misc_init_r(void) u32 reg; unsigned long usb2d0cr = 0; unsigned long usb2phy0cr, usb2h0cr = 0; - unsigned long sdr0_pfc1; + unsigned long sdr0_pfc1, sdr0_srst; /* * FLASH stuff... @@ -158,32 +215,7 @@ int misc_init_r(void) gd->bd->bi_flashoffset = 0; mfebc(PB0CR, pbcr); - switch (gd->bd->bi_flashsize) { - case 1 << 20: - size_val = 0; - break; - case 2 << 20: - size_val = 1; - break; - case 4 << 20: - size_val = 2; - break; - case 8 << 20: - size_val = 3; - break; - case 16 << 20: - size_val = 4; - break; - case 32 << 20: - size_val = 5; - break; - case 64 << 20: - size_val = 6; - break; - case 128 << 20: - size_val = 7; - break; - } + size_val = ffs(gd->bd->bi_flashsize) - 21; pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); mtebc(PB0CR, pbcr); @@ -193,53 +225,92 @@ int misc_init_r(void) flash_get_size(gd->bd->bi_flashstart, 0); /* Monitor protection ON by default */ - (void)flash_protect(FLAG_PROTECT_SET, - -CONFIG_SYS_MONITOR_LEN, - 0xffffffff, - &flash_info[1]); + flash_protect(FLAG_PROTECT_SET, -CONFIG_SYS_MONITOR_LEN, 0xffffffff, + &flash_info[cfi_flash_num_flash_banks - 1]); /* Env protection ON by default */ - (void)flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR_REDUND, - CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1, - &flash_info[1]); + flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND, + CONFIG_ENV_ADDR_REDUND + 2 * CONFIG_ENV_SECT_SIZE - 1, + &flash_info[cfi_flash_num_flash_banks - 1]); /* * USB suff... */ + + /* Reset USB */ + /* Reset of USB2PHY0 must be active at least 10 us */ + mtsdr(SDR0_SRST0, SDR0_SRST0_USB2H | SDR0_SRST0_USB2D); + udelay(2000); + + mtsdr(SDR0_SRST1, SDR0_SRST1_USB20PHY | SDR0_SRST1_USB2HUTMI | + SDR0_SRST1_USB2HPHY | SDR0_SRST1_OPBA2 | + SDR0_SRST1_PLB42OPB1 | SDR0_SRST1_OPB2PLB40); + udelay(2000); + + /* Errata CHIP_6 */ + + /* 1. Set internal PHY configuration */ /* SDR Setting */ mfsdr(SDR0_PFC1, sdr0_pfc1); mfsdr(SDR0_USB0, usb2d0cr); mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); mfsdr(SDR0_USB2H0CR, usb2h0cr); - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/ - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/ - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/ - usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; - usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/ - - /* An 8-bit/60MHz interface is the only possible alternative - when connecting the Device to the PHY */ - usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; - usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/ + usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ + usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/ + usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN; /*1*/ + usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/ + usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/ + + /* + * An 8-bit/60MHz interface is the only possible alternative + * when connecting the Device to the PHY + */ + usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK; + usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/ mtsdr(SDR0_PFC1, sdr0_pfc1); mtsdr(SDR0_USB0, usb2d0cr); mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); mtsdr(SDR0_USB2H0CR, usb2h0cr); + /* 2. De-assert internal PHY reset */ + mfsdr(SDR0_SRST1, sdr0_srst); + sdr0_srst = sdr0_srst & ~SDR0_SRST1_USB20PHY; + mtsdr(SDR0_SRST1, sdr0_srst); + + /* 3. Wait for more than 1 ms */ + udelay(2000); + + /* 4. De-assert USB 2.0 Host main reset */ + mfsdr(SDR0_SRST0, sdr0_srst); + sdr0_srst = sdr0_srst &~ SDR0_SRST0_USB2H; + mtsdr(SDR0_SRST0, sdr0_srst); + udelay(1000); + + /* 5. De-assert reset of OPB2 cores */ + mfsdr(SDR0_SRST1, sdr0_srst); + sdr0_srst = sdr0_srst &~ SDR0_SRST1_PLB42OPB1; + sdr0_srst = sdr0_srst &~ SDR0_SRST1_OPB2PLB40; + sdr0_srst = sdr0_srst &~ SDR0_SRST1_OPBA2; + mtsdr(SDR0_SRST1, sdr0_srst); + udelay(1000); + + /* 6. Set EHCI Configure FLAG */ + + /* 7. Reassert internal PHY reset: */ + mtsdr(SDR0_SRST1, SDR0_SRST1_USB20PHY); + udelay(1000); + /* * Clear resets */ - udelay (1000); mtsdr(SDR0_SRST1, 0x00000000); - udelay (1000); mtsdr(SDR0_SRST0, 0x00000000); printf("USB: Host(int phy) Device(ext phy)\n"); @@ -264,7 +335,7 @@ int checkboard(void) { char *s = getenv("serial#"); - printf("Board: lwmon5"); + puts("Board: lwmon5"); if (s != NULL) { puts(", serial# "); @@ -331,34 +402,33 @@ U_BOOT_CMD( extern GraphicDevice mb862xx; -static const gdc_regs init_regs [] = -{ - {0x0100, 0x00000f00}, - {0x0020, 0x801401df}, - {0x0024, 0x00000000}, - {0x0028, 0x00000000}, - {0x002c, 0x00000000}, - {0x0110, 0x00000000}, - {0x0114, 0x00000000}, - {0x0118, 0x01df0280}, - {0x0004, 0x031f0000}, - {0x0008, 0x027f027f}, - {0x000c, 0x015f028f}, - {0x0010, 0x020c0000}, - {0x0014, 0x01df01ea}, - {0x0018, 0x00000000}, - {0x001c, 0x01e00280}, - {0x0100, 0x80010f00}, - {0x0, 0x0} +static const gdc_regs init_regs [] = { + { 0x0100, 0x00000f00 }, + { 0x0020, 0x801401df }, + { 0x0024, 0x00000000 }, + { 0x0028, 0x00000000 }, + { 0x002c, 0x00000000 }, + { 0x0110, 0x00000000 }, + { 0x0114, 0x00000000 }, + { 0x0118, 0x01df0280 }, + { 0x0004, 0x031f0000 }, + { 0x0008, 0x027f027f }, + { 0x000c, 0x015f028f }, + { 0x0010, 0x020c0000 }, + { 0x0014, 0x01df01ea }, + { 0x0018, 0x00000000 }, + { 0x001c, 0x01e00280 }, + { 0x0100, 0x80010f00 }, + { 0x0, 0x0 } }; -const gdc_regs *board_get_regs (void) +const gdc_regs *board_get_regs(void) { return init_regs; } /* Returns Lime base address */ -unsigned int board_video_init (void) +unsigned int board_video_init(void) { /* * Reset Lime controller @@ -375,7 +445,7 @@ unsigned int board_video_init (void) return CONFIG_SYS_LIME_BASE_0; } -#define DEFAULT_BRIGHTNESS 0x64 +#define DEFAULT_BRIGHTNESS 0x64 static void board_backlight_brightness(int brightness) { @@ -390,7 +460,7 @@ static void board_backlight_brightness(int brightness) } } -void board_backlight_switch (int flag) +void board_backlight_switch(int flag) { char * param; int rc; @@ -410,15 +480,14 @@ void board_backlight_switch (int flag) /* * Return text to be printed besides the logo. */ -void video_get_info_str (int line_number, char *info) +void video_get_info_str(int line_number, char *info) { - if (line_number == 1) { - strcpy (info, " Board: Lwmon5 (Liebherr Elektronik GmbH)"); - } else { + if (line_number == 1) + strcpy(info, " Board: Lwmon5 (Liebherr Elektronik GmbH)"); + else info [0] = '\0'; - } } -#endif +#endif /* CONFIG_CONSOLE_EXTRA_INFO */ #endif /* CONFIG_VIDEO */ void board_reset(void) diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 72e02f8..2349583 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007-2008 + * (C) Copyright 2007-2010 * Stefan Roese, DENX Software Engineering, sr(a)denx.de. * * This program is free software; you can redistribute it and/or @@ -18,58 +18,63 @@ * MA 02111-1307 USA */ -/************************************************************************ +/* * lwmon5.h - configuration for lwmon5 board - ***********************************************************************/ + */ #ifndef __CONFIG_H #define __CONFIG_H -/*----------------------------------------------------------------------- +/* + * Liebherr extra version info + */ +#define CONFIG_IDENT_STRING " - v2.0" + +/* * High Level Configuration Options - *----------------------------------------------------------------------*/ + */ #define CONFIG_LWMON5 1 /* Board is lwmon5 */ #define CONFIG_440EPX 1 /* Specific PPC440EPx */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_BOARD_RESET 1 /* Call board_reset */ +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_early_init_f */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r */ +#define CONFIG_BOARD_POSTCLK_INIT /* Call board_postclk_init */ +#define CONFIG_MISC_INIT_R /* Call misc_init_r */ +#define CONFIG_BOARD_RESET /* Call board_reset */ -/*----------------------------------------------------------------------- +/* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ + */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */ +#define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1) +#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* Reserved for malloc */ #define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE -#define CONFIG_SYS_LIME_BASE_0 0xc0000000 -#define CONFIG_SYS_LIME_BASE_1 0xc1000000 -#define CONFIG_SYS_LIME_BASE_2 0xc2000000 -#define CONFIG_SYS_LIME_BASE_3 0xc3000000 -#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 -#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 +#define CONFIG_SYS_LIME_BASE_0 0xc0000000 +#define CONFIG_SYS_LIME_BASE_1 0xc1000000 +#define CONFIG_SYS_LIME_BASE_2 0xc2000000 +#define CONFIG_SYS_LIME_BASE_3 0xc3000000 +#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 +#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 #define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ #define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 -#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE1 (CONFIG_SYS_PCI_MEMBASE + 0x10000000) +#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE1 + 0x10000000) +#define CONFIG_SYS_PCI_MEMBASE3 (CONFIG_SYS_PCI_MEMBASE2 + 0x10000000) #define CONFIG_SYS_USB2D0_BASE 0xe0000100 #define CONFIG_SYS_USB_DEVICE 0xe0000000 #define CONFIG_SYS_USB_HOST 0xe0000400 -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer - *----------------------------------------------------------------------*/ /* + * Initial RAM & stack pointer + * * On LWMON5 we use D-cache as init-ram and stack pointer. We also move * the POST_WORD from OCM to a 440EPx register that preserves it's * content during reset (GPT0_COMP6). This way we reserve the OCM (16k) @@ -77,18 +82,18 @@ */ #define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ -#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_INIT_RAM_END (4 << 10) #define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data*/ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +/* unused GPT0 COMP reg */ #define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) - /* unused GPT0 COMP reg */ -#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ - /* 440EPx errata CHIP 11 */ #define CONFIG_SYS_OCM_SIZE (16 << 10) +/* 440EPx errata CHIP 11: don't use last 4kbytes */ +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* Additional registers for watchdog timer post test */ - #define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2) #define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1) #define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR @@ -100,9 +105,9 @@ #define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300 #define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00 -/*----------------------------------------------------------------------- +/* * Serial Port - *----------------------------------------------------------------------*/ + */ #define CONFIG_CONS_INDEX 2 /* Use UART1 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL @@ -110,77 +115,79 @@ #define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */ #define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 +#define CONFIG_SERIAL_MULTI #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} -/*----------------------------------------------------------------------- +/* * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + */ +#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ -/*----------------------------------------------------------------------- +/* * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CONFIG_SYS_FLASH0 0xFC000000 #define CONFIG_SYS_FLASH1 0xF8000000 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION /* use hardware flash protection */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CONFIG_SYS_FLASH_QUIET_TEST /* don't warn upon unknown flash */ #define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN) - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -/*----------------------------------------------------------------------- +/* * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ + */ +#define CONFIG_SYS_MBYTES_SDRAM 256 #define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */ -#define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */ -#define CONFIG_DDR_ECC 1 /* enable ECC */ -#define CONFIG_SYS_POST_ECC_ON CONFIG_SYS_POST_ECC +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#define CONFIG_DDR_ECC /* enable ECC */ /* POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_ECC_ON | \ - CONFIG_SYS_POST_ETHER | \ - CONFIG_SYS_POST_FPU | \ - CONFIG_SYS_POST_I2C | \ - CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_OCM | \ - CONFIG_SYS_POST_RTC | \ - CONFIG_SYS_POST_SPR | \ - CONFIG_SYS_POST_UART | \ - CONFIG_SYS_POST_SYSMON | \ - CONFIG_SYS_POST_WATCHDOG | \ - CONFIG_SYS_POST_DSP | \ - CONFIG_SYS_POST_BSPEC1 | \ - CONFIG_SYS_POST_BSPEC2 | \ - CONFIG_SYS_POST_BSPEC3 | \ - CONFIG_SYS_POST_BSPEC4 | \ +#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_ECC | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_FPU | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_OCM | \ + CONFIG_SYS_POST_RTC | \ + CONFIG_SYS_POST_SPR | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_SYSMON | \ + CONFIG_SYS_POST_WATCHDOG | \ + CONFIG_SYS_POST_DSP | \ + CONFIG_SYS_POST_BSPEC1 | \ + CONFIG_SYS_POST_BSPEC2 | \ + CONFIG_SYS_POST_BSPEC3 | \ + CONFIG_SYS_POST_BSPEC4 | \ CONFIG_SYS_POST_BSPEC5) -#define CONFIG_POST_WATCHDOG {\ +/* Define here the base-addresses of the UARTs to test in POST */ +#define CONFIG_SYS_POST_UART_TABLE { UART0_BASE, UART1_BASE } + +#define CONFIG_POST_WATCHDOG { \ "Watchdog timer test", \ "watchdog", \ "This test checks the watchdog timer.", \ @@ -188,10 +195,10 @@ &lwmon5_watchdog_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_WATCHDOG \ + CONFIG_SYS_POST_WATCHDOG \ } -#define CONFIG_POST_BSPEC1 {\ +#define CONFIG_POST_BSPEC1 { \ "dsPIC init test", \ "dspic_init", \ "This test returns result of dsPIC READY test run earlier.", \ @@ -199,10 +206,10 @@ &dspic_init_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC1 \ + CONFIG_SYS_POST_BSPEC1 \ } -#define CONFIG_POST_BSPEC2 {\ +#define CONFIG_POST_BSPEC2 { \ "dsPIC test", \ "dspic", \ "This test gets result of dsPIC POST and dsPIC version.", \ @@ -210,32 +217,32 @@ &dspic_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC2 \ + CONFIG_SYS_POST_BSPEC2 \ } -#define CONFIG_POST_BSPEC3 {\ +#define CONFIG_POST_BSPEC3 { \ "FPGA test", \ "fpga", \ "This test checks FPGA registers and memory.", \ - POST_RAM | POST_ALWAYS, \ + POST_RAM | POST_ALWAYS | POST_MANUAL, \ &fpga_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC3 \ + CONFIG_SYS_POST_BSPEC3 \ } -#define CONFIG_POST_BSPEC4 {\ +#define CONFIG_POST_BSPEC4 { \ "GDC test", \ "gdc", \ "This test checks GDC registers and memory.", \ - POST_RAM | POST_ALWAYS, \ + POST_RAM | POST_ALWAYS | POST_MANUAL,\ &gdc_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC4 \ + CONFIG_SYS_POST_BSPEC4 \ } -#define CONFIG_POST_BSPEC5 {\ +#define CONFIG_POST_BSPEC5 { \ "SYSMON1 test", \ "sysmon1", \ "This test checks GPIO_62_EPX pin indicating power failure.", \ @@ -243,7 +250,7 @@ &sysmon1_post_test, \ NULL, \ NULL, \ - CONFIG_SYS_POST_BSPEC5 \ + CONFIG_SYS_POST_BSPEC5 \ } #define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ @@ -253,34 +260,53 @@ #define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE) #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -/*----------------------------------------------------------------------- +/* * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* RTC */ +#define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52 /* EEPROM (CPU Modul) */ +#define CONFIG_SYS_I2C_EEPROM_MB_ADDR 0x53 /* EEPROM AT24C128 (MainBoard) */ +#define CONFIG_SYS_I2C_DSPIC_ADDR 0x54 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_2_ADDR 0x55 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_KEYB_ADDR 0x56 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* dsPIC */ + #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ /* 64 byte page write mode using*/ /* last 6 bits of the address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE + +#define CONFIG_RTC_PCF8563 /* enable Philips PCF8563 RTC */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ + +#define I2C_ADDR_LIST { \ + CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_EEPROM_CPU_ADDR, \ + CONFIG_SYS_I2C_EEPROM_MB_ADDR, \ + CONFIG_SYS_I2C_DSPIC_ADDR, \ + CONFIG_SYS_I2C_DSPIC_2_ADDR, \ + CONFIG_SYS_I2C_DSPIC_KEYB_ADDR, \ + CONFIG_SYS_I2C_DSPIC_IO_ADDR } -#define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ -#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ -#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +/* Update size in "reg" property of NOR FLASH device tree nodes */ +#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE #define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ -#if 0 -#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ -#define CONFIG_AUTOBOOT_PROMPT \ - "\nEnter password - autoboot in %d sec...\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ -#endif #define CONFIG_PREBOOT "setenv bootdelay 15" @@ -314,15 +340,11 @@ "cp.b 200000 FFF80000 80000\0" \ "upd=run load update\0" \ "lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \ - "source 200000\0" \ + "autoscr 200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ @@ -410,9 +432,9 @@ #define CONFIG_CMD_USB #endif -/*----------------------------------------------------------------------- +/* * Miscellaneous configurable options - *----------------------------------------------------------------------*/ + */ #define CONFIG_SUPPORT_VFAT #define CONFIG_SYS_LONGHELP /* undef to save memory */ @@ -445,9 +467,9 @@ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -/*----------------------------------------------------------------------- +/* * PCI stuff - *----------------------------------------------------------------------*/ + */ /* General PCI */ #define CONFIG_PCI /* include pci support */ #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ @@ -461,29 +483,32 @@ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#ifndef DEBUG #define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */ +#endif #define CONFIG_WD_PERIOD 40000 /* in usec */ #define CONFIG_WD_MAX_RATE 66600 /* in ticks */ /* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the 40x Linux kernel during initialization. */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ -/*----------------------------------------------------------------------- +/* * External Bus Controller (EBC) Setup - *----------------------------------------------------------------------*/ + */ #define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x03050200 +#define CONFIG_SYS_EBC_PB0AP 0x03000280 #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000) /* Memory Bank 1 (Lime) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x01004380 -#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xdc000) +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xbc000) /* Memory Bank 2 (FPGA) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x01004400 @@ -495,19 +520,27 @@ #define CONFIG_SYS_EBC_CFG 0xb8400000 -/*----------------------------------------------------------------------- +/* * Graphics (Fujitsu Lime) - *----------------------------------------------------------------------*/ + */ +/* SDRAM Clock frequency adjustment register */ +#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038 +#if 1 /* 133MHz is not tested enough, use 100MHz for now */ /* Lime Clock frequency is to set 100MHz */ #define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000 -#if 0 +#else /* Lime Clock frequency for 133MHz */ #define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000 #endif -/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars - and pixel flare on display when 133MHz was configured. According to - SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */ +/* SDRAM Parameter register */ +#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC +/* + * SDRAM parameter value; was 0x414FB7F2, caused several vertical bars + * and pixel flare on display when 133MHz was configured. According to + * SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed + * Grade + */ #ifdef CONFIG_SYS_LIME_CLOCK_133MHZ #define CONFIG_SYS_MB862xx_MMR 0x414FB7F3 #define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ @@ -516,13 +549,15 @@ #define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ #endif -/*----------------------------------------------------------------------- +/* * GPIO Setup - *----------------------------------------------------------------------*/ + */ #define CONFIG_SYS_GPIO_PHY1_RST 12 #define CONFIG_SYS_GPIO_FLASH_WP 14 #define CONFIG_SYS_GPIO_PHY0_RST 22 #define CONFIG_SYS_GPIO_DSPIC_READY 51 +#define CONFIG_SYS_GPIO_CAN_ENABLE 53 +#define CONFIG_SYS_GPIO_LSB_ENABLE 54 #define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55 #define CONFIG_SYS_GPIO_HIGHSIDE 56 #define CONFIG_SYS_GPIO_EEPROM_INT_WP 57 @@ -532,7 +567,7 @@ #define CONFIG_SYS_GPIO_SYSMON_STATUS 62 #define CONFIG_SYS_GPIO_WATCHDOG 63 -/*----------------------------------------------------------------------- +/* * PPC440 GPIO Configuration */ #define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ diff --git a/post/board/lwmon5/dsp.c b/post/board/lwmon5/dsp.c index 0e6d908..913cd97 100644 --- a/post/board/lwmon5/dsp.c +++ b/post/board/lwmon5/dsp.c @@ -33,20 +33,37 @@ DECLARE_GLOBAL_DATA_PTR; -#define DSP_STATUS_REG 0xC4000008 +#define DSP_STATUS_REG 0xC4000008 +#define FPGA_STATUS_REG 0xC400000C int dsp_post_test(int flags) { + uint old_value; uint read_value; int ret; + /* momorize fpga status */ + old_value = in_be32((void *)FPGA_STATUS_REG); + /* enable outputs */ + out_be32((void *)FPGA_STATUS_REG, 0x30); + + /* generate sync signal */ + out_be32((void *)DSP_STATUS_REG, 0x300); + udelay(5); + out_be32((void *)DSP_STATUS_REG, 0); + udelay(500); + + /* read status */ ret = 0; read_value = in_be32((void *)DSP_STATUS_REG) & 0x3; - if (read_value != 0x3) { + if (read_value != 0x03) { post_log("\nDSP status read %08X\n", read_value); ret = 1; } + /* restore fpga status */ + out_be32((void *)FPGA_STATUS_REG, old_value); + return ret; } diff --git a/post/board/lwmon5/dspic.c b/post/board/lwmon5/dspic.c index ff2ed05..8616739 100644 --- a/post/board/lwmon5/dspic.c +++ b/post/board/lwmon5/dspic.c @@ -38,14 +38,16 @@ DECLARE_GLOBAL_DATA_PTR; #define DSPIC_POST_ERROR_REG 0x800 #define DSPIC_SYS_ERROR_REG 0x802 -#define DSPIC_VERSION_REG 0x804 +#define DSPIC_SYS_VERSION_REG 0x804 +#define DSPIC_FW_VERSION_REG 0x808 #if CONFIG_POST & CONFIG_SYS_POST_BSPEC1 /* Verify that dsPIC ready test done early at hw init passed ok */ int dspic_init_post_test(int flags) { - if (in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) & CONFIG_SYS_DSPIC_TEST_MASK) { + if (in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) & + CONFIG_SYS_DSPIC_TEST_MASK) { post_log("dsPIC init test failed\n"); return 1; } @@ -57,46 +59,60 @@ int dspic_init_post_test(int flags) #if CONFIG_POST & CONFIG_SYS_POST_BSPEC2 /* Read a register from the dsPIC. */ -int dspic_read(ushort reg) +int dspic_read(ushort reg, ushort *data) { - uchar buf[2]; + uchar buf[sizeof(*data)]; + int rval; if (i2c_read(CONFIG_SYS_I2C_DSPIC_IO_ADDR, reg, 2, buf, 2)) return -1; + rval = i2c_read(CONFIG_SYS_I2C_DSPIC_IO_ADDR, reg, sizeof(reg), + buf, sizeof(*data)); + *data = (buf[0] << 8) | buf[1]; - return (uint)((buf[0] << 8) | buf[1]); + return rval; } /* Verify error codes regs, display version */ int dspic_post_test(int flags) { - int data; + ushort data; int ret = 0; post_log("\n"); - data = dspic_read(DSPIC_VERSION_REG); - if (data == -1) { - post_log("dsPIC : failed read version\n"); + + /* read dspic FW-Version */ + if (dspic_read(DSPIC_FW_VERSION_REG, &data)) { + post_log("dsPIC: failed read FW-Version\n"); + ret = 1; + } else { + post_log("dsPIC FW-Version: %u.%u\n", + (data >> 8) & 0xFF, data & 0xFF); + } + + /* read dspic SYS-Version */ + if (dspic_read(DSPIC_SYS_VERSION_REG, &data)) { + post_log("dsPIC: failed read version\n"); ret = 1; } else { - post_log("dsPIC version: %u.%u\n", - (data >> 8) & 0xFF, data & 0xFF); + post_log("dsPIC SYS-Version: %u.%u\n", + (data >> 8) & 0xFF, data & 0xFF); } - data = dspic_read(DSPIC_POST_ERROR_REG); - if (data != 0) ret = 1; - if (data == -1) { - post_log("dsPIC : failed read POST code\n"); + /* read dspic POST error code */ + if (dspic_read(DSPIC_POST_ERROR_REG, &data)) { + post_log("dsPIC: failed read POST code\n"); + ret = 1; } else { - post_log("dsPIC POST code 0x%04X\n", data); + post_log("dsPIC POST-ERROR code: 0x%04X\n", data); } - data = dspic_read(DSPIC_SYS_ERROR_REG); - if (data == -1) { - post_log("dsPIC : failed read system error\n"); + /* read dspic SYS error code */ + if ((data = dspic_read(DSPIC_SYS_ERROR_REG, &data))) { + post_log("dsPIC: failed read system error\n"); ret = 1; } else { - post_log("dsPIC SYS-ERROR code: 0x%04X\n", data); + post_log("dsPIC SYS-ERROR code: 0x%04X\n", data); } return ret; diff --git a/post/board/lwmon5/fpga.c b/post/board/lwmon5/fpga.c index 2b84290..3067548 100644 --- a/post/board/lwmon5/fpga.c +++ b/post/board/lwmon5/fpga.c @@ -28,7 +28,7 @@ */ #include <post.h> - +#include <watchdog.h> #include <asm/io.h> DECLARE_GLOBAL_DATA_PTR; @@ -38,18 +38,28 @@ DECLARE_GLOBAL_DATA_PTR; #define FPGA_RAM_START 0xC4200000 #define FPGA_RAM_END 0xC4203FFF #define FPGA_STAT 0xC400000C +#define FPGA_BUFFER 0x00800000 +#define FPGA_RAM_SIZE (FPGA_RAM_END - FPGA_RAM_START + 1) #if CONFIG_POST & CONFIG_SYS_POST_BSPEC3 -/* Testpattern for fpga memorytest */ -static uint pattern[] = { +const static unsigned long pattern[] = { + 0xffffffff, + 0xaaaaaaaa, + 0xcccccccc, + 0xf0f0f0f0, + 0xff00ff00, + 0xffff0000, + 0x0000ffff, + 0x00ff00ff, + 0x0f0f0f0f, + 0x33333333, 0x55555555, - 0xAAAAAAAA, - 0xAA5555AA, - 0x55AAAA55, - 0x0 + 0x00000000, }; +const static unsigned long otherpattern = 0x01234567; + static int one_scratch_test(uint value) { uint read_value; @@ -62,51 +72,226 @@ static int one_scratch_test(uint value) read_value = in_be32((void *)FPGA_SCRATCH_REG); if (read_value != value) { post_log("FPGA SCRATCH test failed write %08X, read %08X\n", - value, read_value); - ret = 1; + value, read_value); + ret = -1; + } + + return ret; +} + +static int fpga_post_test1(ulong *start, ulong size, ulong val) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = val; + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != val) { + post_log("FPGA Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, val, readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + return ret; +} + +static int fpga_post_test2(ulong *start, ulong size) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = 1 << (i % 32); + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != 1 << (i % 32)) { + post_log("FPGA Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, 1 << (i % 32), readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + return ret; +} + +static int fpga_post_test3(ulong *start, ulong size) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = i; + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != i) { + post_log("FPGA Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, i, readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + return ret; +} + +static int fpga_post_test4(ulong *start, ulong size) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = ~i; + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != ~i) { + post_log("FPGA Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, ~i, readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); } return ret; } /* FPGA Memory-pattern-test */ -static int fpga_mem_test(void * address) +static int fpga_mem_test(void) { - int ret = 1; - uint read_value; - uint old_value; - uint i = 0; - /* save content */ - old_value = in_be32(address); - - while (pattern[i] != 0) { - out_be32(address, pattern[i]); - /* read other location (protect against data lines capacity) */ - ret = in_be16((void *)FPGA_VERSION_REG); - /* verify test pattern */ - read_value = in_be32(address); - - if (read_value != pattern[i]) { - post_log("FPGA Memory test failed."); - post_log(" write %08X, read %08X at address %08X\n", - pattern[i], read_value, address); + int ret = 0; + ulong* start = (ulong *)FPGA_RAM_START; + ulong size = FPGA_RAM_SIZE; + + if (ret == 0) + ret = fpga_post_test1(start, size, 0x00000000); + + if (ret == 0) + ret = fpga_post_test1(start, size, 0xffffffff); + + if (ret == 0) + ret = fpga_post_test1(start, size, 0x55555555); + + if (ret == 0) + ret = fpga_post_test1(start, size, 0xaaaaaaaa); + + WATCHDOG_RESET(); + + if (ret == 0) + ret = fpga_post_test2(start, size); + + if (ret == 0) + ret = fpga_post_test3(start, size); + + if (ret == 0) + ret = fpga_post_test4(start, size); + + return ret; +} + + + +/* Verify FPGA addresslines */ +static int fpga_post_addrline(ulong *address, ulong *base, ulong size) +{ + unsigned long *target; + unsigned long *end; + unsigned long readback; + unsigned long xor; + int ret = 0; + + end = (ulong *)((ulong)base + size); + xor = 0; + + for (xor = sizeof(ulong); xor > 0; xor <<= 1) { + target = (ulong*)((ulong)address ^ xor); + if ((target >= base) && (target < end)) { + *address = ~*target; + readback = *target; + + if (readback == *address) { + post_log("Memory (address line) error at %08x" + "XOR value %08x !\n", + address, target, xor); + ret = -1; + break; + } + } + } + + return ret; +} + +/* Verify FPGA addresslines */ +static int fpga_post_dataline(ulong *address) +{ + unsigned long temp32 = 0; + int i = 0; + int ret = 0; + + for (i = 0; i < ARRAY_SIZE(pattern); i++) { + *address = pattern[i]; + /* + * Put a different pattern on the data lines: otherwise they + * may float long enough to read back what we wrote. + */ + *(address + 1) = otherpattern; + temp32 = *address; + + if (temp32 != pattern[i]){ + post_log("Memory (date line) error at %08x, " + "wrote %08x, read %08x !\n", + address, pattern[i], temp32); ret = 1; - goto out; } - i++; } - ret = 0; -out: - out_be32(address, old_value); return ret; } + /* Verify FPGA, get version & memory size */ int fpga_post_test(int flags) { - uint address; uint old_value; - ushort version; + uint version; uint read_value; int ret = 0; @@ -120,24 +305,57 @@ int fpga_post_test(int flags) out_be32((void *)FPGA_SCRATCH_REG, old_value); - version = in_be16((void *)FPGA_VERSION_REG); - post_log("FPGA : version %u.%u\n", - (version >> 8) & 0xFF, version & 0xFF); + version = in_be32((void *)FPGA_VERSION_REG); + post_log("FPGA version %u.%u\n", + (version >> 8) & 0xFF, version & 0xFF); /* Enable write to FPGA RAM */ out_be32((void *)FPGA_STAT, in_be32((void *)FPGA_STAT) | 0x1000); - read_value = get_ram_size((void *)CONFIG_SYS_FPGA_BASE_1, 0x4000); - post_log("FPGA RAM size: %d bytes\n", read_value); + /* get RAM size */ + read_value = get_ram_size((void *)CONFIG_SYS_FPGA_BASE_1, FPGA_RAM_SIZE); + post_log("FPGA RAM size %d bytes\n", read_value); + WATCHDOG_RESET(); - for (address = 0; address < 0x1000; address++) { - if (fpga_mem_test((void *)(FPGA_RAM_START + 4*address)) == 1) { - ret = 1; - goto out; - } + /* copy fpga memory to DDR2 RAM*/ + memcpy((void *)FPGA_BUFFER,(void *)FPGA_RAM_START, FPGA_RAM_SIZE); + WATCHDOG_RESET(); + + /* Test datalines */ + if (fpga_post_dataline((ulong *)FPGA_RAM_START)) { + ret = 1; + goto out; + } + WATCHDOG_RESET(); + + /* Test addresslines */ + if (fpga_post_addrline((ulong *)FPGA_RAM_START, + (ulong *)FPGA_RAM_START, FPGA_RAM_SIZE)) { + ret = 1; + goto out; } + WATCHDOG_RESET(); + if (fpga_post_addrline((ulong *)FPGA_RAM_END - sizeof(long), + (ulong *)FPGA_RAM_START, FPGA_RAM_SIZE)) { + ret = 1; + goto out; + } + WATCHDOG_RESET(); + + /* Memory Pattern Test */ + if (fpga_mem_test()) { + ret = 1; + goto out; + } + WATCHDOG_RESET(); + + /* restore memory */ + memcpy((void *)FPGA_RAM_START,(void *)FPGA_BUFFER, FPGA_RAM_SIZE); + WATCHDOG_RESET(); out: + /* Disable write to RAM */ + out_be32((void *)FPGA_STAT, in_be32((void *)FPGA_STAT) & 0xEFFF); return ret; } diff --git a/post/board/lwmon5/gdc.c b/post/board/lwmon5/gdc.c index eb16e36..719194b 100644 --- a/post/board/lwmon5/gdc.c +++ b/post/board/lwmon5/gdc.c @@ -28,18 +28,39 @@ */ #include <post.h> - +#include <watchdog.h> #include <asm/io.h> +#include <video.h> DECLARE_GLOBAL_DATA_PTR; -#define GDC_SCRATCH_REG 0xC1FF8044 -#define GDC_VERSION_REG 0xC1FF8084 -#define GDC_RAM_START 0xC0000000 -#define GDC_RAM_END 0xC2000000 +#define GDC_SCRATCH_REG 0xC1FF8044 +#define GDC_VERSION_REG 0xC1FF8084 +#define GDC_HOST_BASE 0xC1FC0000 +#define GDC_RAM_START 0xC0000000 +#define GDC_RAM_END (GDC_HOST_BASE - 1) +#define GDC_RAM_SIZE (GDC_RAM_END - GDC_RAM_START) #if CONFIG_POST & CONFIG_SYS_POST_BSPEC4 +const static unsigned long pattern[] = { + 0xffffffff, + 0xaaaaaaaa, + 0xcccccccc, + 0xf0f0f0f0, + 0xff00ff00, + 0xffff0000, + 0x0000ffff, + 0x00ff00ff, + 0x0f0f0f0f, + 0x33333333, + 0x55555555, + 0x00000000 +}; + +const static unsigned long otherpattern = 0x01234567; + +/* test write/read og a given LIME Register */ static int gdc_test_reg_one(uint value) { int ret; @@ -53,17 +74,229 @@ static int gdc_test_reg_one(uint value) read_value = in_be32((void *)GDC_SCRATCH_REG); if (read_value != value) { post_log("GDC SCRATCH test failed write %08X, read %08X\n", - value, read_value); + value, read_value); } return (read_value != value); } -/* Verify GDC, get memory size */ +/* test with a given static 32 bit pattern in a given memory addressrange */ +static int gdc_post_test1(ulong *start, ulong size, ulong val) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = val; + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != val) { + post_log("GDC Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, val, readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + return ret; +} + +/* test with dynamic 32 bit pattern in a given memory addressrange */ +static int gdc_post_test2(ulong *start, ulong size) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = 1 << (i % 32); + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != 1 << (i % 32)) { + post_log("GDC Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, 1 << (i % 32), readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + return ret; +} + +/* test with dynamic 32 bit pattern in a given memory addressrange */ +static int gdc_post_test3(ulong *start, ulong size) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = i; + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != i) { + post_log("GDC Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, i, readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + return ret; +} + +/* test with dynamic 32 bit pattern in a given memory addressrange */ +static int gdc_post_test4(ulong *start, ulong size) +{ + int ret = 0; + ulong i = 0; + ulong *mem = start; + ulong readback; + + for (i = 0; i < size / sizeof(ulong); i++) { + mem[i] = ~i; + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + for (i = 0; i < size / sizeof(ulong); i++) { + readback = mem[i]; + if (readback != ~i) { + post_log("GDC Memory error at %08x, " + "wrote %08x, read %08x !\n", + mem + i, ~i, readback); + ret = -1; + break; + } + if (i % 1024 == 0) + WATCHDOG_RESET(); + } + + return ret; +} + +/* do some patterntests in a given addressrange */ +int gdc_mem_test(ulong *start, ulong size) +{ + int ret = 0; + + /* + * check addressrange and do different static and dynamic + * pattern tests with it. + */ + if (((void *)start) + size <= (void *)GDC_RAM_END) { + if (ret == 0) + ret = gdc_post_test1(start, size, 0x00000000); + + if (ret == 0) + ret = gdc_post_test1(start, size, 0xffffffff); + + if (ret == 0) + ret = gdc_post_test1(start, size, 0x55555555); + + if (ret == 0) + ret = gdc_post_test1(start, size, 0xaaaaaaaa); + + if (ret == 0) + ret = gdc_post_test2(start, size); + + if (ret == 0) + ret = gdc_post_test3(start, size); + + if (ret == 0) + ret = gdc_post_test4(start, size); + } + + return ret; +} + +/* test function of gdc memory addresslines*/ +static int gdc_post_addrline(ulong *address, ulong *base, ulong size) +{ + ulong *target; + ulong *end; + ulong readback = 0; + ulong xor = 0; + int ret = 0; + + end = (ulong *)((ulong)base + size); + + for (xor = sizeof(long); xor > 0; xor <<= 1) { + target = (ulong *)((ulong)address ^ xor); + if ((target >= base) && (target < end)) { + *address = ~*target; + readback = *target; + } + + if (readback == *address) { + post_log("GDC Memory (address line) error at %08x" + "XOR value %08x !\n", + address, target , xor); + ret = -1; + break; + } + } + + return ret; +} + +static int gdc_post_dataline(ulong *address) +{ + unsigned long temp32 = 0; + int i = 0; + int ret = 0; + + for (i = 0; i < ARRAY_SIZE(pattern); i++) { + *address = pattern[i]; + /* + * Put a different pattern on the data lines: otherwise they + * may float long enough to read back what we wrote. + */ + *(address + 1) = otherpattern; + temp32 = *address; + + if (temp32 != pattern[i]){ + post_log("GDC Memory (date line) error at %08x, " + "wrote %08x, read %08x !\n", + address, pattern[i], temp32); + ret = 1; + } + } + + return ret; +} + +/* Verify GDC, get memory size, verify GDC memory */ int gdc_post_test(int flags) { - uint old_value; - int ret = 0; + uint old_value; + int i = 0; + int ret = 0; post_log("\n"); old_value = in_be32((void *)GDC_SCRATCH_REG); @@ -84,13 +317,64 @@ int gdc_post_test(int flags) old_value = in_be32((void *)GDC_VERSION_REG); post_log("GDC chip version %u.%u, year %04X\n", - (old_value >> 8) & 0xFF, old_value & 0xFF, - (old_value >> 16) & 0xFFFF); + (old_value >> 8) & 0xFF, old_value & 0xFF, + (old_value >> 16) & 0xFFFF); old_value = get_ram_size((void *)GDC_RAM_START, - GDC_RAM_END - GDC_RAM_START); + 0x02000000); + + debug("GDC RAM size (ist): %d bytes\n", old_value); + debug("GDC RAM size (soll): %d bytes\n", GDC_RAM_SIZE); post_log("GDC RAM size: %d bytes\n", old_value); + /* Test SDRAM datalines */ + if (gdc_post_dataline((ulong *)GDC_RAM_START)) { + ret = 1; + goto out; + } + WATCHDOG_RESET(); + + /* Test SDRAM adresslines */ + if (gdc_post_addrline((ulong *)GDC_RAM_START, + (ulong *)GDC_RAM_START, GDC_RAM_SIZE)) { + ret = 1; + goto out; + } + WATCHDOG_RESET(); + if (gdc_post_addrline((ulong *)GDC_RAM_END - sizeof(long), + (ulong *)GDC_RAM_START, GDC_RAM_SIZE)) { + ret = 1; + goto out; + } + WATCHDOG_RESET(); + + /* memory pattern test */ + debug("GDC Memory test (flags %8x:%8x)\n", flags, + POST_SLOWTEST | POST_MANUAL); + + if (flags & POST_MANUAL) { + debug("Full memory test\n"); + if (gdc_mem_test((ulong *)GDC_RAM_START, GDC_RAM_SIZE)) { + ret = 1; + goto out; + } + /* load splashscreen again */ + } else { + debug("smart memory test\n"); + for (i = 0; i < (GDC_RAM_SIZE >> 20) && ret == 0; i++) { + if (ret == 0) + ret = gdc_mem_test((ulong *)(GDC_RAM_START + + (i << 20)), + 0x800); + if (ret == 0) + ret = gdc_mem_test((ulong *)(GDC_RAM_START + + (i << 20) + 0xff800), + 0x800); + } + } + WATCHDOG_RESET(); + +out: return ret; } #endif /* CONFIG_POST & CONFIG_SYS_POST_BSPEC4 */ diff --git a/post/board/lwmon5/sysmon.c b/post/board/lwmon5/sysmon.c index 9c49d0e..4a78240 100644 --- a/post/board/lwmon5/sysmon.c +++ b/post/board/lwmon5/sysmon.c @@ -56,7 +56,7 @@ DECLARE_GLOBAL_DATA_PTR; /* from dspic.c */ -extern int dspic_read(ushort reg); +extern int dspic_read(ushort reg, ushort *data); #define REG_TEMPERATURE 0x12BC #define REG_VOLTAGE_5V 0x12CA @@ -76,31 +76,38 @@ extern int dspic_read(ushort reg); typedef struct sysmon_s sysmon_t; typedef struct sysmon_table_s sysmon_table_t; -static void sysmon_dspic_init (sysmon_t * this); -static int sysmon_dspic_read (sysmon_t * this, uint addr); -static void sysmon_backlight_disable (sysmon_table_t * this); +static void sysmon_dspic_init(sysmon_t *this); +static int sysmon_dspic_read(sysmon_t *this, uint addr, int *val); +static int sysmon_dspic_read_sgn(sysmon_t *this, uint addr, int *val); +static void sysmon_backlight_disable(sysmon_table_t *this); -struct sysmon_s -{ +struct sysmon_s { uchar chip; void (*init)(sysmon_t *); - int (*read)(sysmon_t *, uint); + int (*read)(sysmon_t *, uint, int *); }; -static sysmon_t sysmon_dspic = - {CONFIG_SYS_I2C_DSPIC_IO_ADDR, sysmon_dspic_init, sysmon_dspic_read}; +static sysmon_t sysmon_dspic = { + CONFIG_SYS_I2C_DSPIC_IO_ADDR, + sysmon_dspic_init, + sysmon_dspic_read +}; -static sysmon_t * sysmon_list[] = -{ +static sysmon_t sysmon_dspic_sgn = { + CONFIG_SYS_I2C_DSPIC_IO_ADDR, + sysmon_dspic_init, + sysmon_dspic_read_sgn +}; + +static sysmon_t *sysmon_list[] = { &sysmon_dspic, NULL }; -struct sysmon_table_s -{ - char * name; - char * unit_name; - sysmon_t * sysmon; +struct sysmon_table_s { + char *name; + char *unit_name; + sysmon_t *sysmon; void (*exec_before)(sysmon_table_t *); void (*exec_after)(sysmon_table_t *); @@ -118,37 +125,43 @@ struct sysmon_table_s uint addr; }; -static sysmon_table_t sysmon_table[] = -{ +static sysmon_table_t sysmon_table[] = { { - "Temperature", " C", &sysmon_dspic, NULL, sysmon_backlight_disable, - 1, 1, -32768, 32767, 0xFFFF, - 0x8000 + TEMPERATURE_MIN, 0x8000 + TEMPERATURE_MAX, 0, - 0x8000 + TEMPERATURE_DISPLAY_MIN, 0x8000 + TEMPERATURE_DISPLAY_MAX, 0, - REG_TEMPERATURE, + "Temperature", " C", &sysmon_dspic, NULL, sysmon_backlight_disable, + 1, 1, -32768, 32767, 0xFFFF, + 0x8000 + TEMPERATURE_MIN, 0x8000 + TEMPERATURE_MAX, 0, + 0x8000 + TEMPERATURE_DISPLAY_MIN, 0x8000 + TEMPERATURE_DISPLAY_MAX, 0, + REG_TEMPERATURE, }, { - "+ 5 V", "V", &sysmon_dspic, NULL, NULL, - 100, 1000, -0x8000, 0x7FFF, 0xFFFF, - 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0, - 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0, - REG_VOLTAGE_5V, + "+ 5 V", "V", &sysmon_dspic, NULL, NULL, + 100, 1000, -0x8000, 0x7FFF, 0xFFFF, + 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0, + 0x8000 + VOLTAGE_5V_MIN, 0x8000 + VOLTAGE_5V_MAX, 0, + REG_VOLTAGE_5V, }, { - "+ 5 V standby", "V", &sysmon_dspic, NULL, NULL, - 100, 1000, -0x8000, 0x7FFF, 0xFFFF, - 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0, - 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0, - REG_VOLTAGE_5V_STANDBY, + "+ 5 V standby", "V", &sysmon_dspic, NULL, NULL, + 100, 1000, -0x8000, 0x7FFF, 0xFFFF, + 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0, + 0x8000 + VOLTAGE_5V_STANDBY_MIN, 0x8000 + VOLTAGE_5V_STANDBY_MAX, 0, + REG_VOLTAGE_5V_STANDBY, + }, + + { + "Temperature", "°C", &sysmon_dspic_sgn, NULL, sysmon_backlight_disable, + 1, 1, -32768, 32767, 0xFFFF, + 0x8000 + TEMPERATURE_MIN, 0x8000 + TEMPERATURE_MAX, 0, + 0x8000 + TEMPERATURE_DISPLAY_MIN, 0x8000 + TEMPERATURE_DISPLAY_MAX, 0, + REG_TEMPERATURE, }, }; -static int sysmon_table_size = sizeof(sysmon_table) / sizeof(sysmon_table[0]); -int sysmon_init_f (void) +int sysmon_init_f(void) { - sysmon_t ** l; + sysmon_t **l; for (l = sysmon_list; *l; l++) (*l)->init(*l); @@ -156,12 +169,12 @@ int sysmon_init_f (void) return 0; } -void sysmon_reloc (void) +void sysmon_reloc(void) { /* Do nothing for now, sysmon_reloc() is required by the sysmon post */ } -static char *sysmon_unit_value (sysmon_table_t *s, uint val) +static char *sysmon_unit_value(sysmon_table_t *s, uint val) { static char buf[32]; char *p, sign; @@ -176,14 +189,13 @@ static char *sysmon_unit_value (sysmon_table_t *s, uint val) if (unit_val < 0) { sign = '-'; unit_val = -unit_val; - } else + } else { sign = '+'; + } p = buf + sprintf(buf, "%c%2d", sign, unit_val / s->unit_div); - frac = unit_val % s->unit_div; - frac /= (s->unit_div / s->unit_precision); decimal = s->unit_precision; @@ -197,58 +209,84 @@ static char *sysmon_unit_value (sysmon_table_t *s, uint val) return buf; } -static void sysmon_dspic_init (sysmon_t * this) +static void sysmon_dspic_init(sysmon_t *this) { } -static int sysmon_dspic_read (sysmon_t * this, uint addr) +static int sysmon_dspic_read(sysmon_t *this, uint addr, int *val) { - int res = dspic_read(addr); + ushort data; + + if (dspic_read(addr, &data) == 0){ + /* To fit into the table range we should add 0x8000 */ + *val = data + 0x8000; + return 0; + } - /* To fit into the table range we should add 0x8000 */ - return (res == -1) ? -1 : (res + 0x8000); + return -1; } -static void sysmon_backlight_disable (sysmon_table_t * this) +static int sysmon_dspic_read_sgn(sysmon_t *this, uint addr, int *val) +{ + ushort data; + + if (dspic_read(addr, &data) == 0){ + /* To fit into the table range we should add 0x8000 */ + *val = (signed short)data + 0x8000; + return 0; + } + + return -1; +} + +static void sysmon_backlight_disable(sysmon_table_t *this) { #if defined(CONFIG_VIDEO) board_backlight_switch(this->val_valid_alt); #endif } -int sysmon_post_test (int flags) +int sysmon_post_test(int flags) { int res = 0; sysmon_table_t * t; int val; - for (t = sysmon_table; t < sysmon_table + sysmon_table_size; t ++) { + for (t = sysmon_table; t < sysmon_table + ARRAY_SIZE(sysmon_table); t++) { + t->val_valid = 1; if (t->exec_before) t->exec_before(t); - val = t->sysmon->read(t->sysmon, t->addr); - if (val != -1) { - t->val_valid = val >= t->val_min && val <= t->val_max; - t->val_valid_alt = val >= t->val_min_alt && val <= t->val_max_alt; - } else { + if (t->sysmon->read(t->sysmon, t->addr, &val) != 0) { t->val_valid = 0; t->val_valid_alt = 0; + post_log(": read failed\n"); + res = 1; + break; + } + + if (t->val_valid != 0) { + t->val_valid = val >= t->val_min && val <= t->val_max; + t->val_valid_alt = val >= t->val_min_alt && val <= t->val_max_alt; } if (t->exec_after) t->exec_after(t); - if ((!t->val_valid) || (flags & POST_MANUAL)) { - printf("%-17s = %-10s ", t->name, sysmon_unit_value(t, val)); - printf("allowed range"); - printf(" %-8s ..", sysmon_unit_value(t, t->val_min)); - printf(" %-8s", sysmon_unit_value(t, t->val_max)); - printf(" %s\n", t->val_valid ? "OK" : "FAIL"); + if ((!t->val_valid) || (flags)) { + post_log("\n\t%-17s = %-10s ", t->name, sysmon_unit_value(t, val)); + post_log("allowed range"); + post_log(" %-8s ..", sysmon_unit_value(t, t->val_min)); + post_log(" %-8s", sysmon_unit_value(t, t->val_max)); + post_log(" %s", t->val_valid ? "OK" : "FAIL"); } - if (!t->val_valid) + if (!t->val_valid) { res = 1; + break; + } } + post_log("\n"); return res; } diff --git a/post/board/lwmon5/watchdog.c b/post/board/lwmon5/watchdog.c index f181506..4e5ed0d 100644 --- a/post/board/lwmon5/watchdog.c +++ b/post/board/lwmon5/watchdog.c @@ -57,8 +57,11 @@ int sysmon1_post_test(int flags) * 3.1. GPIO62 is low * Assuming system voltage failure. */ - post_log("Abnormal voltage detected (GPIO62)\n"); + post_log("sysmon1 Abnormal voltage detected (GPIO62)\n"); + post_log("POST sysmon1 FAILED\n"); return 1; + } else { + post_log("sysmon1 PASSED\n"); } return 0; @@ -117,10 +120,16 @@ int lwmon5_watchdog_post_test(int flags) ulong time; /* 3.3.1. So, the test succeed, save measured time to syslog. */ time = in_be32((void *)CONFIG_SYS_WATCHDOG_TIME_ADDR); - post_log("hw watchdog time : %u ms, passed ", time); - /* 3.3.2. Set scratch register 1 to 0x0000xxxx */ - watchdog_magic_write(0); - return 0; + if (time > 90 ) { /* ms*/ + post_log("hw watchdog time : %u ms, passed ", time); + /* 3.3.2. Set scratch register 1 to 0x0000xxxx */ + watchdog_magic_write(0); + return 0; + } else { + /*test minimum watchdogtime */ + post_log("hw watchdog time : %u ms, failed ", time); + return 2; + } } return -1; } -- 1.7.3

1 1

[U-Boot] [PATCH v7 1/2] APM821xx: Add CPU support
by tmarri＠apm.com 04 Oct '10

04 Oct '10

From: Tirumala Marri <tmarri(a)apm.com> APM821XX is a new line of SoCs which are derivatives of PPC44X family of processors. This patch adds support of CPU, cache, tlb, 32k ocm, bootstraps, PLB and AHB bus. Signed-off-by: Tirumala R Marri <tmarri(a)apm.com> --- V6: * Correcting indentation. V7: * Ordering defined(APM821XX) in cpu_init.c . --- arch/powerpc/cpu/ppc4xx/cpu.c | 19 ++++++++ arch/powerpc/cpu/ppc4xx/cpu_init.c | 5 +- arch/powerpc/cpu/ppc4xx/speed.c | 75 ++++++++++++++++++++++++++++++- arch/powerpc/cpu/ppc4xx/start.S | 11 +++-- arch/powerpc/include/asm/apm821xx.h | 72 +++++++++++++++++++++++++++++ arch/powerpc/include/asm/ppc4xx-ebc.h | 3 +- arch/powerpc/include/asm/ppc4xx-isram.h | 14 +++++- arch/powerpc/include/asm/ppc4xx-sdram.h | 12 +++--- arch/powerpc/include/asm/ppc4xx-uic.h | 5 +- arch/powerpc/include/asm/ppc4xx.h | 4 ++ arch/powerpc/include/asm/processor.h | 1 + 11 files changed, 202 insertions(+), 19 deletions(-) diff --git a/arch/powerpc/cpu/ppc4xx/cpu.c b/arch/powerpc/cpu/ppc4xx/cpu.c index 6009b0c..67f1fff 100644 --- a/arch/powerpc/cpu/ppc4xx/cpu.c +++ b/arch/powerpc/cpu/ppc4xx/cpu.c @@ -250,6 +250,20 @@ static char *bootstrap_str[] = { }; static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'G', 'F', 'H' }; #endif +#if defined(CONFIG_APM821XX) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "RESERVED", + "RESERVED", + "RESERVED", + "NAND (8 bits)", + "NOR (8 bits)", + "NOR (8 bits) w/PLL Bypassed", + "I2C (Addr 0x54)", + "I2C (Addr 0x52)", +}; +static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'F', 'G', 'H' }; +#endif #if defined(SDR0_PINSTP_SHIFT) static int bootstrap_option(void) @@ -590,6 +604,11 @@ int checkcpu (void) strcpy(addstr, "No Security support"); break; + case PVR_APM821XX_RA: + puts("APM821XX Rev. A"); + strcpy(addstr, "Security support"); + break; + case PVR_VIRTEX5: puts("440x5 VIRTEX5"); break; diff --git a/arch/powerpc/cpu/ppc4xx/cpu_init.c b/arch/powerpc/cpu/ppc4xx/cpu_init.c index d54b30e..2a727b1 100644 --- a/arch/powerpc/cpu/ppc4xx/cpu_init.c +++ b/arch/powerpc/cpu/ppc4xx/cpu_init.c @@ -237,7 +237,8 @@ cpu_init_f (void) reconfigure_pll(CONFIG_SYS_PLL_RECONFIG); -#if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && !defined(CONFIG_SYS_4xx_GPIO_TABLE) +#if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && \ + !defined(CONFIG_APM821XX) &&!defined(CONFIG_SYS_4xx_GPIO_TABLE) /* * GPIO0 setup (select GPIO or alternate function) */ @@ -393,7 +394,7 @@ cpu_init_f (void) #if defined(CONFIG_405EX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ - defined(CONFIG_460SX) + defined(CONFIG_460SX) || defined(CONFIG_APM821XX) /* * Set PLB4 arbiter (Segment 0 and 1) to 4 deep pipeline read */ diff --git a/arch/powerpc/cpu/ppc4xx/speed.c b/arch/powerpc/cpu/ppc4xx/speed.c index abd4e91..09d6671 100644 --- a/arch/powerpc/cpu/ppc4xx/speed.c +++ b/arch/powerpc/cpu/ppc4xx/speed.c @@ -189,7 +189,7 @@ ulong get_PCI_freq (void) #elif defined(CONFIG_440) #if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ - defined(CONFIG_460SX) + defined(CONFIG_460SX) || defined(CONFIG_APM821XX) static u8 pll_fwdv_multi_bits[] = { /* values for: 1 - 16 */ 0x00, 0x01, 0x0f, 0x04, 0x09, 0x0a, 0x0d, 0x0e, 0x03, 0x0c, @@ -250,6 +250,78 @@ u32 get_cpr0_fbdv(unsigned long cpr_reg_fbdv) return 0; } +#if defined(CONFIG_APM821XX) + +void get_sys_info(sys_info_t *sysInfo) +{ + unsigned long plld; + unsigned long temp; + unsigned long mul; + unsigned long cpudv; + unsigned long plb2dv; + unsigned long ddr2dv; + + /* Calculate Forward divisor A and Feeback divisor */ + mfcpr(CPR0_PLLD, plld); + + temp = CPR0_PLLD_FWDVA(plld); + sysInfo->pllFwdDivA = get_cpr0_fwdv(temp); + + temp = CPR0_PLLD_FDV(plld); + sysInfo->pllFbkDiv = get_cpr0_fbdv(temp); + + /* Calculate OPB clock divisor */ + mfcpr(CPR0_OPBD, temp); + temp = CPR0_OPBD_OPBDV(temp); + sysInfo->pllOpbDiv = temp ? temp : 4; + + /* Calculate Peripheral clock divisor */ + mfcpr(CPR0_PERD, temp); + temp = CPR0_PERD_PERDV(temp); + sysInfo->pllExtBusDiv = temp ? temp : 4; + + /* Calculate CPU clock divisor */ + mfcpr(CPR0_CPUD, temp); + temp = CPR0_CPUD_CPUDV(temp); + cpudv = temp ? temp : 8; + + /* Calculate PLB2 clock divisor */ + mfcpr(CPR0_PLB2D, temp); + temp = CPR0_PLB2D_PLB2DV(temp); + plb2dv = temp ? temp : 4; + + /* Calculate DDR2 clock divisor */ + mfcpr(CPR0_DDR2D, temp); + temp = CPR0_DDR2D_DDR2DV(temp); + ddr2dv = temp ? temp : 4; + + /* Calculate 'M' based on feedback source */ + mfcpr(CPR0_PLLC, temp); + temp = CPR0_PLLC_SEL(temp); + if (temp == 0) { + /* PLL internal feedback */ + mul = sysInfo->pllFbkDiv; + } else { + /* PLL PerClk feedback */ + mul = sysInfo->pllFwdDivA * sysInfo->pllFbkDiv * cpudv + * plb2dv * 2 * sysInfo->pllOpbDiv * + sysInfo->pllExtBusDiv; + } + + /* Now calculate the individual clocks */ + sysInfo->freqVCOMhz = (mul * CONFIG_SYS_CLK_FREQ) + (mul >> 1); + sysInfo->freqProcessor = sysInfo->freqVCOMhz / + sysInfo->pllFwdDivA / cpudv; + sysInfo->freqPLB = sysInfo->freqVCOMhz / + sysInfo->pllFwdDivA / cpudv / plb2dv / 2; + sysInfo->freqOPB = sysInfo->freqPLB / sysInfo->pllOpbDiv; + sysInfo->freqEBC = sysInfo->freqOPB / sysInfo->pllExtBusDiv; + sysInfo->freqDDR = sysInfo->freqVCOMhz / + sysInfo->pllFwdDivA / cpudv / ddr2dv / 2; + sysInfo->freqUART = sysInfo->freqPLB; +} + +#else /* * AMCC_TODO: verify this routine against latest EAS, cause stuff changed * with latest EAS @@ -307,6 +379,7 @@ void get_sys_info (sys_info_t * sysInfo) return; } +#endif #elif defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) diff --git a/arch/powerpc/cpu/ppc4xx/start.S b/arch/powerpc/cpu/ppc4xx/start.S index 7a65d9f..c2d52bf 100644 --- a/arch/powerpc/cpu/ppc4xx/start.S +++ b/arch/powerpc/cpu/ppc4xx/start.S @@ -703,7 +703,8 @@ _start: defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ defined(CONFIG_460SX) mtdcr L2_CACHE_CFG,r0 /* Ensure L2 Cache is off */ -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) +#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_APM821XX) lis r1, 0x0000 ori r1,r1,0x0008 /* Set L2_CACHE_CFG[RDBW]=1 */ mtdcr L2_CACHE_CFG,r1 @@ -731,7 +732,8 @@ _start: lis r1, 0x8003 ori r1,r1, 0x0980 /* fourth 64k */ mtdcr ISRAM0_SB3CR,r1 -#elif defined(CONFIG_440SPE) || defined(CONFIG_460EX) || defined(CONFIG_460GT) +#elif defined(CONFIG_440SPE) || defined(CONFIG_460EX) || \ + defined(CONFIG_460GT) || defined(CONFIG_APM821XX) lis r1,0x0000 /* BAS = X_0000_0000 */ ori r1,r1,0x0984 /* first 64k */ mtdcr ISRAM0_SB0CR,r1 @@ -744,7 +746,8 @@ _start: lis r1, 0x0003 ori r1,r1, 0x0984 /* fourth 64k */ mtdcr ISRAM0_SB3CR,r1 -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_APM821XX) lis r2,0x7fff ori r2,r2,0xffff mfdcr r1,ISRAM1_DPC @@ -755,7 +758,7 @@ _start: mtdcr ISRAM1_PMEG,r1 lis r1,0x0004 /* BAS = 4_0004_0000 */ - ori r1,r1,0x0984 /* 64k */ + ori r1,r1,ISRAM1_SIZE /* ocm size */ mtdcr ISRAM1_SB0CR,r1 #endif #elif defined(CONFIG_460SX) diff --git a/arch/powerpc/include/asm/apm821xx.h b/arch/powerpc/include/asm/apm821xx.h new file mode 100644 index 0000000..8841bc9 --- /dev/null +++ b/arch/powerpc/include/asm/apm821xx.h @@ -0,0 +1,72 @@ +/* + * Copyright (c) 2010, Applied Micro Circuits Corporation + * Author: Tirumala R Marri <tmarri(a)apm.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _APM821XX_H_ +#define _APM821XX_H_ + +#define CONFIG_SDRAM_PPC4xx_IBM_DDR2 /* IBM DDR(2) controller */ + +/* Memory mapped registers */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_PERIPHERAL_BASE + 0x0200) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_PERIPHERAL_BASE + 0x0300) + +#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x0700) + +#define SDR0_SRST0_DMC 0x00200000 +#define SDR0_SRST1_AHB 0x00000040 /* PLB4XAHB bridge */ + +/* AHB config. */ +#define AHB_TOP 0xA4 +#define AHB_BOT 0xA5 + +/* clk divisors */ +#define PLLSYS0_FWD_DIV_A_MASK 0x000000f0 /* Fwd Div A */ +#define PLLSYS0_FWD_DIV_B_MASK 0x0000000f /* Fwd Div B */ +#define PLLSYS0_FB_DIV_MASK 0x0000ff00 /* Feedback divisor */ +#define PLLSYS0_OPB_DIV_MASK 0x0c000000 /* OPB Divisor */ +#define PLLSYS0_EPB_DIV_MASK 0x00000300 /* EPB divisor */ +#define PLLSYS0_EXTSL_MASK 0x00000080 /* PerClk feedback path */ +#define PLLSYS0_PLBEDV0_DIV_MASK 0xe0000000/* PLB Early Clk Div*/ +#define PLLSYS0_PERCLK_DIV_MASK 0x03000000 /* Peripheral Clk Divisor */ +#define PLLSYS0_SEL_MASK 0x18000000 /* 0 = PLL, 1 = PerClk */ + +/* + + * Clocking Controller + + */ +#define CPR0_CLKUPD 0x0020 +#define CPR0_PLLC 0x0040 +#define CPR0_PLLC_SEL(pllc) (((pllc) & 0x01000000) >> 24) +#define CPR0_PLLD 0x0060 +#define CPR0_PLLD_FDV(plld) (((plld) & 0xff000000) >> 24) +#define CPR0_PLLD_FWDVA(plld) (((plld) & 0x000f0000) >> 16) +#define CPR0_CPUD 0x0080 +#define CPR0_CPUD_CPUDV(cpud) (((cpud) & 0x07000000) >> 24) +#define CPR0_PLB2D 0x00a0 +#define CPR0_PLB2D_PLB2DV(plb2d) (((plb2d) & 0x06000000) >> 25) +#define CPR0_OPBD 0x00c0 +#define CPR0_OPBD_OPBDV(opbd) (((opbd) & 0x03000000) >> 24) +#define CPR0_PERD 0x00e0 +#define CPR0_PERD_PERDV(perd) (((perd) & 0x03000000) >> 24) +#define CPR0_DDR2D 0x0100 +#define CPR0_DDR2D_DDR2DV(ddr2d) (((ddr2d) & 0x06000000) >> 25) +#define CLK_ICFG 0x0140 + +#endif /* _APM821XX_H_ */ diff --git a/arch/powerpc/include/asm/ppc4xx-ebc.h b/arch/powerpc/include/asm/ppc4xx-ebc.h index 9c17e46..75af130 100644 --- a/arch/powerpc/include/asm/ppc4xx-ebc.h +++ b/arch/powerpc/include/asm/ppc4xx-ebc.h @@ -69,7 +69,8 @@ #define EBC_NUM_BANKS 6 #endif -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_APM821XX) #define EBC_NUM_BANKS 3 #endif diff --git a/arch/powerpc/include/asm/ppc4xx-isram.h b/arch/powerpc/include/asm/ppc4xx-isram.h index d6d17ac..32e1297 100644 --- a/arch/powerpc/include/asm/ppc4xx-isram.h +++ b/arch/powerpc/include/asm/ppc4xx-isram.h @@ -25,7 +25,8 @@ /* * Internal SRAM */ -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_APM821XX) #define ISRAM0_DCR_BASE 0x380 #else #define ISRAM0_DCR_BASE 0x020 @@ -42,7 +43,8 @@ #define ISRAM0_REVID (ISRAM0_DCR_BASE+0x09) /* SRAM bus revision id reg */ #define ISRAM0_DPC (ISRAM0_DCR_BASE+0x0a) /* SRAM data parity check reg */ -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_APM821XX) #define ISRAM1_DCR_BASE 0x0B0 #define ISRAM1_SB0CR (ISRAM1_DCR_BASE+0x00) /* SRAM1 bank config 0*/ #define ISRAM1_BEAR (ISRAM1_DCR_BASE+0x04) /* SRAM1 bus error addr reg */ @@ -54,13 +56,19 @@ #define ISRAM1_DPC (ISRAM1_DCR_BASE+0x0a) /* SRAM1 data parity check reg */ #endif /* CONFIG_460EX || CONFIG_460GT */ +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#define ISRAM1_SIZE 0x0984 /* OCM size 64k */ +#elif defined(CONFIG_APM821XX) +#define ISRAM1_SIZE 0x0784 /* OCM size 32k */ +#endif + /* * L2 Cache */ #if defined (CONFIG_440GX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ - defined(CONFIG_460SX) + defined(CONFIG_460SX) || defined(CONFIG_APM821XX) #define L2_CACHE_BASE 0x030 #define L2_CACHE_CFG (L2_CACHE_BASE+0x00) /* L2 Cache Config */ #define L2_CACHE_CMD (L2_CACHE_BASE+0x01) /* L2 Cache Command */ diff --git a/arch/powerpc/include/asm/ppc4xx-sdram.h b/arch/powerpc/include/asm/ppc4xx-sdram.h index ac150c2..d570d79 100644 --- a/arch/powerpc/include/asm/ppc4xx-sdram.h +++ b/arch/powerpc/include/asm/ppc4xx-sdram.h @@ -292,7 +292,7 @@ */ #if defined(CONFIG_440SPE) || \ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ - defined(CONFIG_460SX) + defined(CONFIG_460SX) || defined(CONFIG_APM821XX) #define SDRAM_RXBAS_SDBA_MASK 0xFFE00000 /* Base address */ #define SDRAM_RXBAS_SDBA_ENCODE(n) ((u32)(((phys_size_t)(n) >> 2) & 0xFFE00000)) #define SDRAM_RXBAS_SDBA_DECODE(n) ((((phys_size_t)(n)) & 0xFFE00000) << 2) @@ -365,7 +365,7 @@ /* * Memory controller registers */ -#ifdef CONFIG_405EX +#if defined(CONFIG_405EX) || defined(CONFIG_APM821XX) #define SDRAM_BESR 0x00 /* PLB bus error status (read/clear) */ #define SDRAM_BESRT 0x01 /* PLB bus error status (test/set) */ #define SDRAM_BEARL 0x02 /* PLB bus error address low */ @@ -375,9 +375,9 @@ #define SDRAM_PLBOPT 0x08 /* PLB slave options */ #define SDRAM_PUABA 0x09 /* PLB upper address base */ #define SDRAM_MCSTAT 0x1F /* memory controller status */ -#else /* CONFIG_405EX */ +#else /* CONFIG_405EX || CONFIG_APM821XX */ #define SDRAM_MCSTAT 0x14 /* memory controller status */ -#endif /* CONFIG_405EX */ +#endif /* CONFIG_405EX || CONFIG_APM821XX */ #define SDRAM_MCOPT1 0x20 /* memory controller options 1 */ #define SDRAM_MCOPT2 0x21 /* memory controller options 2 */ #define SDRAM_MODT0 0x22 /* on die termination for bank 0 */ @@ -423,12 +423,12 @@ #define SDRAM_MEMODE 0x89 /* memory extended mode */ #define SDRAM_ECCES 0x98 /* ECC error status */ #define SDRAM_CID 0xA4 /* core ID */ -#ifndef CONFIG_405EX +#if !defined(CONFIG_405EX) && !defined(CONFIG_APM821XX) #define SDRAM_RID 0xA8 /* revision ID */ #endif #define SDRAM_FCSR 0xB0 /* feedback calibration status */ #define SDRAM_RTSR 0xB1 /* run time status tracking */ -#ifdef CONFIG_405EX +#if defined(CONFIG_405EX) || defined(CONFIG_APM821XX) #define SDRAM_RID 0xF8 /* revision ID */ #endif diff --git a/arch/powerpc/include/asm/ppc4xx-uic.h b/arch/powerpc/include/asm/ppc4xx-uic.h index 782d045..3714a0a 100644 --- a/arch/powerpc/include/asm/ppc4xx-uic.h +++ b/arch/powerpc/include/asm/ppc4xx-uic.h @@ -31,7 +31,7 @@ */ #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ - defined(CONFIG_460SX) + defined(CONFIG_460SX) || defined(CONFIG_APM821XX) #define UIC_MAX 4 #elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ defined(CONFIG_405EX) @@ -252,7 +252,8 @@ #define VECNUM_ETH0 (32 + 28) #endif /* CONFIG_440SPE */ -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_APM821XX) /* UIC 0 */ #define VECNUM_UIC2NCI 10 #define VECNUM_UIC2CI 11 diff --git a/arch/powerpc/include/asm/ppc4xx.h b/arch/powerpc/include/asm/ppc4xx.h index 87a16ec..1b98f8b 100644 --- a/arch/powerpc/include/asm/ppc4xx.h +++ b/arch/powerpc/include/asm/ppc4xx.h @@ -79,6 +79,10 @@ #include <asm/ppc460sx.h> #endif +#if defined(CONFIG_APM821XX) +#include <asm/apm821xx.h> +#endif + /* * Configure which SDRAM/DDR/DDR2 controller is equipped */ diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h index 84a1e2e..9cafe85 100644 --- a/arch/powerpc/include/asm/processor.h +++ b/arch/powerpc/include/asm/processor.h @@ -916,6 +916,7 @@ #define PVR_460SX_RA_V1 0x13541801 /* 460SX rev A Variant 1 Security disabled */ #define PVR_460GX_RA 0x13541802 /* 460GX rev A */ #define PVR_460GX_RA_V1 0x13541803 /* 460GX rev A Variant 1 Security disabled */ +#define PVR_APM821XX_RA 0x12C41C80 /* APM821XX rev A */ #define PVR_601 0x00010000 #define PVR_602 0x00050000 #define PVR_603 0x00030000 -- 1.6.1.rc3

3 2