April 2008 - U-Boot

[U-Boot-Users] [PATCH] minor cs8900 driver clean up
by Guennadi Liakhovetski 03 Apr '08

03 Apr '08

Remove a redundant register definition, clean up some coding style violations. Signed-off-by: Guennadi Liakhovetski <lg(a)denx.de> --- diff --git a/drivers/net/cs8900.c b/drivers/net/cs8900.c index 55ef346..458b517 100644 --- a/drivers/net/cs8900.c +++ b/drivers/net/cs8900.c @@ -65,14 +65,14 @@ static unsigned short get_reg_init_bus (int regno) c = CS8900_BUS16_0; CS8900_PPTR = regno; - return (unsigned short) CS8900_PDATA; + return CS8900_PDATA; } #endif static unsigned short get_reg (int regno) { CS8900_PPTR = regno; - return (unsigned short) CS8900_PDATA; + return CS8900_PDATA; } @@ -131,7 +131,7 @@ void cs8900_get_enetaddr (uchar * addr) if (get_reg_init_bus (PP_ChipID) != 0x630e) return; eth_reset (); - if ((get_reg (PP_SelfST) & (PP_SelfSTAT_EEPROM | PP_SelfSTAT_EEPROM_OK)) == + if ((get_reg (PP_SelfSTAT) & (PP_SelfSTAT_EEPROM | PP_SelfSTAT_EEPROM_OK)) == (PP_SelfSTAT_EEPROM | PP_SelfSTAT_EEPROM_OK)) { /* Load the MAC from EEPROM */ @@ -168,7 +168,6 @@ void cs8900_get_enetaddr (uchar * addr) debug ("### Set environment from HW MAC addr = \"%s\"\n", ethaddr); setenv ("ethaddr", ethaddr); } - } } @@ -183,7 +182,6 @@ void eth_halt (void) int eth_init (bd_t * bd) { - /* verify chip id */ if (get_reg_init_bus (PP_ChipID) != 0x630e) { printf ("CS8900 Ethernet chip not found?!\n"); @@ -201,7 +199,7 @@ int eth_init (bd_t * bd) } /* Get a data block via Ethernet */ -extern int eth_rx (void) +int eth_rx (void) { int i; unsigned short rxlen; @@ -233,7 +231,7 @@ extern int eth_rx (void) } /* Send a data block via Ethernet. */ -extern int eth_send (volatile void *packet, int length) +int eth_send (volatile void *packet, int length) { volatile unsigned short *addr; int tmo; @@ -281,7 +279,8 @@ retry: static void cs8900_e2prom_ready(void) { - while(get_reg(PP_SelfST) & SI_BUSY); + while (get_reg(PP_SelfSTAT) & SI_BUSY) + ; } /***********************************************************/ diff --git a/drivers/net/cs8900.h b/drivers/net/cs8900.h index f886d10..f9c32dd 100644 --- a/drivers/net/cs8900.h +++ b/drivers/net/cs8900.h @@ -243,7 +243,6 @@ /* EEPROM Kram */ #define SI_BUSY 0x0100 -#define PP_SelfST 0x0136 /* Self State register */ #define PP_EECMD 0x0040 /* NVR Interface Command register */ #define PP_EEData 0x0042 /* NVR Interface Data Register */ #define EEPROM_WRITE_EN 0x00F0

1 0

[U-Boot-Users] [PATCH] MX31ADS network and flash updates
by Guennadi Liakhovetski 03 Apr '08

03 Apr '08

This patch depends on the previous two patches, introducing the CONFIG_FLASH_SPANSION_S29WS_N and CONFIG_ARP_TIMEOUT configuration options. It allows U-Boot to use buffered writes to the Spansion NOR flash installed on this board, and eliminates long delays in network transfers after the board startup. Also modify flash layout to embed main and redundant environment blocks in the U-Boot image. Signed-off-by: Guennadi Liakhovetski <lg(a)denx.de> --- diff --git a/board/mx31ads/mx31ads.c b/board/mx31ads/mx31ads.c index 7c50c02..5a7d8c9 100644 --- a/board/mx31ads/mx31ads.c +++ b/board/mx31ads/mx31ads.c @@ -38,18 +38,18 @@ int dram_init (void) int board_init (void) { int i; -#if 0 + /* CS0: Nor Flash */ /* - * These are values from the RedBoot sources by Freescale. However, - * under U-Boot with this configuration 32-bit accesses don't work, - * lower 16 bits of data are read twice for each 32-bit read. + * CS0L and CS0A values are from the RedBoot sources by Freescale + * and are also equal to those used by Sascha Hauer for the Phytec + * i.MX31 board. CS0U is just a slightly optimized hardware default: + * the only non-zero field "Wait State Control" is set to half the + * default value. */ - __REG(CSCR_U(0)) = 0x23524E80; - __REG(CSCR_L(0)) = 0x10000D03; /* WRAP bit (1) is suspicious here, but - * disabling it doesn't help either */ + __REG(CSCR_U(0)) = 0x00000f00; + __REG(CSCR_L(0)) = 0x10000D03; __REG(CSCR_A(0)) = 0x00720900; -#endif /* setup pins for UART1 */ mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX); diff --git a/board/mx31ads/u-boot.lds b/board/mx31ads/u-boot.lds index 1460adc..49713d4 100644 --- a/board/mx31ads/u-boot.lds +++ b/board/mx31ads/u-boot.lds @@ -34,7 +34,18 @@ SECTIONS . = ALIGN(4); .text : { - cpu/arm1136/start.o (.text) + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/arm1136/start.o (.text) + board/mx31ads/libmx31ads.a (.text) + lib_arm/libarm.a (.text) + net/libnet.a (.text) + drivers/mtd/libmtd.a (.text) + + . = DEFINED(env_offset) ? env_offset : .; + common/environment.o(.text) + *(.text) } diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index 77a9a83..9b72c89 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -72,7 +72,6 @@ #include <config_cmd_default.h> -#define CONFIG_CMD_MII #define CONFIG_CMD_PING #define CONFIG_BOOTDELAY 3 @@ -91,7 +90,19 @@ #define CONFIG_DRIVER_CS8900 1 #define CS8900_BASE 0xb4020300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CS8900_BUS16 1 /* follow the Linux driver */ + +/* + * The MX31ADS board seems to have a hardware "peculiarity" confirmed under + * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A + * controller inverted. The controller is capable of detecting and correcting + * this, but it needs 4 network packets for that. Which means, at startup, you + * will not receive answers to the first 4 packest, unless there have been some + * broadcasts on the network, or your board is on a hub. Reducing the ARP + * timeout from default 5 seconds to 200ms we speed up the initial TFTP + * transfer, should the user wish one, significantly. + */ +#define CONFIG_ARP_TIMEOUT 2UL /* * Miscellaneous configurable options @@ -100,7 +111,7 @@ #define CFG_PROMPT "=> " #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ /* Print Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ @@ -136,25 +147,29 @@ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 262 /* max number of sectors on one chip */ #define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */ -#define CFG_MONITOR_LEN (128 * 1024) /* Reserve 128KiB */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */ #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SECT_SIZE (32 * 1024) #define CFG_ENV_SIZE CFG_ENV_SECT_SIZE + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE + /* S29WS256N NOR flash has 4 32KiB small sectors at the beginning and at the end. * The rest of 32MiB is in 128KiB big sectors. U-Boot occupies the low 4 sectors, * if we put environment next to it, we will have to occupy 128KiB for it. * Putting it at the top of flash we use only 32KiB. */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 32 * 1024 * 1024 - CFG_ENV_SIZE) +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_ENV_SECT_SIZE) /*----------------------------------------------------------------------- * CFI FLASH driver setup */ #define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ #define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ -#if 0 /* Doesn't work yet, work in progress */ +#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ -#endif #define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */ /*

1 0

Re: [U-Boot-Users] help - u-boot header & compression
by Luigi 'Comio' Mantellini 03 Apr '08

03 Apr '08

Hi Avinash, You should check the nand_spl and openand_ipl directories to see examples how to start u-boot from a not bootable memory (like nand). Best regards, luigi On mer, 2008-04-02 at 14:26 -0700, Avinash Vijayvergia wrote: > Hi Luig > > Thank you for your mail. I actually have two questions: > 1. What is the format of u-boot header? Can you refer me to some > documentation? > 2. I want to compress u-boot. I have picked up nrv2b.c from > Koders.com which is in use by many people :). I couldn't > understand how it does encoding and decoding. I wanted to use > this algo and do compression and decompression of my binaries. > You can search google for nrv2b.c and you will get it from > Koder.com. > Thanks for your help > Avinash > > ----- Original Message ---- > From: Luigi 'Comio' Mantellini <luigi.mantellini(a)idf-hit.com> > To: Avinash Vijayvergia <avinashs36(a)yahoo.com> > Cc: u-boot-users(a)lists.sourceforge.net > Sent: Wednesday, April 2, 2008 2:19:36 PM > Subject: Re: [U-Boot-Users] help - u-boot header & compression > > Hi Avinash, > > I'm not undestanding if you want compress the U-Boot code or if you > want compress the uImage image. > Anyway, I don't know the nrv2b algorithm, can you give me any links? > > thanks, > > luigi > > Il giorno mer, 02/04/2008 alle 13.54 -0700, Avinash Vijayvergia ha > scritto: > > Hi All > > > > I am working on AT91SAM9260 ARM9 core. I have very small flash > > memory and hence need to compress the u-boot. I have picked nrv2b > > algo for that. Can someone suggest me how to put the compression > > info in the u-boot header. I want to know the details of u-boot > > header too. > > > > Thanks > > Avinash > > > > > > ____________________________________________________________________ > > > > You rock. That's why Blockbuster's offering you one month of > > Blockbuster Total Access, No Cost. > > ------------------------------------------------------------------------- > > Check out the new SourceForge.net Marketplace. > > It's the best place to buy or sell services for > > just about anything Open Source. > > http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace > > _______________________________________________ U-Boot-Users mailing list U-Boot-Users(a)lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/u-boot-users > > Ing. Luigi Mantellini > Industrie Dial Face S.p.A. > Via Canzo, 4 > 20068 Peschiera Borromeo (MI) > Tel.: +39 02 5167 2813 > Fax: +39 02 5167 2459 > E-mail: > luigi.mantellini(a)idf-hit.com > > > > > > > > ______________________________________________________________________ > You rock. That's why Blockbuster's offering you one month of > Blockbuster Total Access, No Cost. -- ______ Luigi Mantellini .'______'. R&D - Software (.' '.) Industrie Dial Face S.p.A. ( :=----=: ) Via Canzo, 4 ('.______.') 20068 Peschiera Borromeo (MI), Italy '.______.' Tel.: +39 02 5167 2813 Fax: +39 02 5167 2459 Ind. Dial Face Email: luigi.mantellini(a)idf-hit.com www.idf-hit.com GPG fingerprint: 3DD1 7B71 FBDF 6376 1B4A B003 175F E979 907E 1650

1 0

[U-Boot-Users] [PATCH] mpc83xx: Fix the SATA clock setting of 837x targets
by Dave Liu 03 Apr '08

03 Apr '08

Currently the SATA controller clock is configured as CSB clock, usually the CSB clock is 400/333/266MHz. However, The SATA IP block is only guaranteed to operate up to 200 MHz as stated in the HW spec. The bug is reported by Joe D'Abbraccio <ljd015(a)freescale.com> This patch makes the SATA clock as half of CSB clock. Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- include/configs/MPC837XEMDS.h | 2 +- include/configs/MPC837XERDB.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 7c4e76e..7fc0f7e 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -96,7 +96,7 @@ */ #define CFG_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ #define CFG_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ -#define CFG_SCCR_SATACM SCCR_SATACM_1 /* CSB:SATA[0:3] = 1:1 */ +#define CFG_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */ /* * System IO Config diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index eaac525..c698ff8 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -108,7 +108,7 @@ /* System Clock Configuration Register */ #define CFG_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */ #define CFG_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */ -#define CFG_SCCR_SATACM SCCR_SATACM_1 /* SATA1-4 clock mode (0-3) */ +#define CFG_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */ /* * System IO Config -- 1.5.4.rc4

1 0

[U-Boot-Users] Pointer to similar board?
by PatM 03 Apr '08

03 Apr '08

I've been trying to get Das u-boot going on my S3C2410 based board and had no luck so far. Just trying to get something over the serial port for now. I have a Wiggler to JTAG the initial u-boot.bin Part of the problem is the target is brand new and not supported by anybody yet. I'm wondering if there's a similar board already supported by u-boot? Its the CUWin at http://cubloc.com/product/05_01.php NOR Am29LV800 NAND 2 x K9F1208 RAM 64MB SDRAM No extra drivers, just the built in S3C2410 LCD, serial, ethernet et. al. I'd like to put u-boot in NOR to save some NAND space and because I can't make heads nor tails out of this steppingstones stuff. Thanks for your patience and help!

2 1

[U-Boot-Users] FW: u-boot ppc440epx bootstrap configuration without eval board
by Dave Cogley 03 Apr '08

03 Apr '08

Forwarded to u-boot mailing list... -----Original Message----- From: Stefan Roese [mailto:sr@denx.de] Sent: Wednesday, April 02, 2008 12:01 PM To: linuxppc-embedded(a)ozlabs.org Cc: Dave Cogley Subject: Re: u-boot ppc440epx bootstrap configuration without eval board On Wednesday 02 April 2008, Dave Cogley wrote: > Disregard the boot strapping problem. It appears we are hardwired strapped > to use option "C" however my CPU is not being recognized as a 667MHz. > Which option should I be using for the 667MHz processor? First, this is the wrong mailing list for this discussion. Please post to the U-Boot list instead. But here some general comments: The bootstrap controller has multiple configuration options. Some of them result in hardwired frequencies (CPU, PLB, OPB...), and some of them load the PLL setup from an I2C EEPROM. Using this bootstrap EEPROM is the most flexible solution. If you have only option "C", then you hardwired to 533MHz. There is no way to "detect" which frequency this CPU is labeled. But it *is* possible to reconfigure the PLL from within U-Boot an reset the PPC to run with this different PLL setup. I just recently added some code the u-boot-ppc4xx custodian repository. Let's continue this thread on the U-Boot list. Best regards, Stefan ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office(a)denx.de =====================================================================

2 1

Re: [U-Boot-Users] help - u-boot header & compression
by Avinash Vijayvergia 03 Apr '08

03 Apr '08

Hi Luigi Thank you for your mail and comments. I should have explain why I want to compress u-boot. My target processor is Atmel AT91SAM9260. I am having a 64Mb Dataflash which is interfaced on SPI bus. The Atmel ARM9 copies the first 4kB to internal SRAM and then boots from there. So we need a loader of size <4kb which will be copied to SRAM. I have got this loader. This loader will invoke u-boot, and u-boot will invoke kernel. So I can compress loader and it will still work. I'll compare nrv2b and lzma and then will be in a better position to comment. I chose nrv2b because I need a compression algo which can be as small as 600B (I have size restriction of 4kB). Thanks Avinash ----- Original Message ---- From: Luigi 'Comio' Mantellini <luigi.mantellini(a)idf-hit.com> To: Avinash Vijayvergia <avinashs36(a)yahoo.com> Cc: u-boot-users(a)lists.sourceforge.net Sent: Wednesday, April 2, 2008 2:37:20 PM Subject: Re: [U-Boot-Users] help - u-boot header & compression Hi Avinash, see inline. Il giorno mer, 02/04/2008 alle 14.26 -0700, Avinash Vijayvergia ha scritto: Hi LuigI Thank you for your mail. I actually have two questions: What is the format of u-boot header? Can you refer me to some documentation? What do you intend for "u-boot header"? U-boot uses the uImage format for the kernels images. You can check the file include/image.h (row 175) to understand the (old) uImage format. See this link: http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=blob;f=include/image.h… I want to compress u-boot. I have picked up nrv2b.c from Koders.com which is in use by many people :). I couldn't understand how it does encoding and decoding. I wanted to use this algo and do compression and decompression of my binaries. You can search google for nrv2b.c and you will get it from Koder.com. U-boot is the object code, the bootloader... how can you compress it? it is a non-sense for me. Anyway, if you need to compress the kernel image, you need to use the uImage format and the utility mkimage (see tools directory). I recently posted a patch to support the lzma compression algorithm (that works better than bzip2 and gzip): you can search in the mailing list archive to retrieve this patch. Are you sure that nrv2b is better than powerful lzma or bzip2? Do you have benchmarks on this point? If you demonstrate me that nrv2b is a good choice I can consider to make the patch for the community... I have an application that has a very small flash memory... nrv2b should be a choice... Best regards, luigi Thanks for your help Avinash ----- Original Message ---- From: Luigi 'Comio' Mantellini <luigi.mantellini(a)idf-hit.com> To: Avinash Vijayvergia <avinashs36(a)yahoo.com> Cc: u-boot-users(a)lists.sourceforge.net Sent: Wednesday, April 2, 2008 2:19:36 PM Subject: Re: [U-Boot-Users] help - u-boot header & compression Hi Avinash, I'm not undestanding if you want compress the U-Boot code or if you want compress the uImage image. Anyway, I don't know the nrv2b algorithm, can you give me any links? thanks, luigi Il giorno mer, 02/04/2008 alle 13.54 -0700, Avinash Vijayvergia ha scritto: Hi All I am working on AT91SAM9260 ARM9 core. I have very small flash memory and hence need to compress the u-boot. I have picked nrv2b algo for that. Can someone suggest me how to put the compression info in the u-boot header. I want to know the details of u-boot header too. Thanks Avinash You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost. ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ U-Boot-Users mailing list U-Boot-Users(a)lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/u-boot-users Ing. Luigi Mantellini Industrie Dial Face S.p.A. Via Canzo, 4 20068 Peschiera Borromeo (MI) Tel.: +39 02 5167 2813 Fax: +39 02 5167 2459 E-mail: luigi.mantellini(a)idf-hit.com You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost. Ing. Luigi Mantellini Industrie Dial Face S.p.A. Via Canzo, 4 20068 Peschiera Borromeo (MI) Tel.: +39 02 5167 2813 Fax: +39 02 5167 2459 E-mail: luigi.mantellini(a)idf-hit.com ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost. http://tc.deals.yahoo.com/tc/blockbuster/text5.com

2 1

Re: [U-Boot-Users] help - u-boot header & compression
by Luigi 'Comio' Mantellini 02 Apr '08

02 Apr '08

Hi Avinash, see inline. Il giorno mer, 02/04/2008 alle 14.26 -0700, Avinash Vijayvergia ha scritto: > Hi LuigI > > Thank you for your mail. I actually have two questions: > 1. What is the format of u-boot header? Can you refer me to some > documentation? What do you intend for "u-boot header"? U-boot uses the uImage format for the kernels images. You can check the file include/image.h (row 175) to understand the (old) uImage format. See this link: http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=blob;f=include/image.h… > 1. I want to compress u-boot. I have picked up nrv2b.c from > Koders.com which is in use by many people :). I couldn't > understand how it does encoding and decoding. I wanted to use > this algo and do compression and decompression of my binaries. > You can search google for nrv2b.c and you will get it from > Koder.com. U-boot is the object code, the bootloader... how can you compress it? it is a non-sense for me. Anyway, if you need to compress the kernel image, you need to use the uImage format and the utility mkimage (see tools directory). I recently posted a patch to support the lzma compression algorithm (that works better than bzip2 and gzip): you can search in the mailing list archive to retrieve this patch. Are you sure that nrv2b is better than powerful lzma or bzip2? Do you have benchmarks on this point? If you demonstrate me that nrv2b is a good choice I can consider to make the patch for the community... I have an application that has a very small flash memory... nrv2b should be a choice... Best regards, luigi > Thanks for your help > Avinash > > > ----- Original Message ---- > From: Luigi 'Comio' Mantellini <luigi.mantellini(a)idf-hit.com> > To: Avinash Vijayvergia <avinashs36(a)yahoo.com> > Cc: u-boot-users(a)lists.sourceforge.net > Sent: Wednesday, April 2, 2008 2:19:36 PM > Subject: Re: [U-Boot-Users] help - u-boot header & compression > > Hi Avinash, > > I'm not undestanding if you want compress the U-Boot code or if you > want compress the uImage image. > Anyway, I don't know the nrv2b algorithm, can you give me any links? > > thanks, > > luigi > > Il giorno mer, 02/04/2008 alle 13.54 -0700, Avinash Vijayvergia ha > scritto: > > > Hi All > > > > I am working on AT91SAM9260 ARM9 core. I have very small flash > > memory and hence need to compress the u-boot. I have picked nrv2b > > algo for that. Can someone suggest me how to put the compression > > info in the u-boot header. I want to know the details of u-boot > > header too. > > > > Thanks > > Avinash > > > > > > ____________________________________________________________________ > > > > You rock. That's why Blockbuster's offering you one month of > > Blockbuster Total Access, No Cost. > > > > ------------------------------------------------------------------------- > > Check out the new SourceForge.net Marketplace. > > It's the best place to buy or sell services for > > just about anything Open Source. > > http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace > > _______________________________________________ U-Boot-Users mailing list U-Boot-Users(a)lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/u-boot-users > > > Ing. Luigi Mantellini > Industrie Dial Face S.p.A. > Via Canzo, 4 > 20068 Peschiera Borromeo (MI) > Tel.: +39 02 5167 2813 > Fax: +39 02 5167 2459 > E-mail: > luigi.mantellini(a)idf-hit.com > > > > > > > > > > ______________________________________________________________________ > You rock. That's why Blockbuster's offering you one month of > Blockbuster Total Access, No Cost. Ing. Luigi Mantellini Industrie Dial Face S.p.A. Via Canzo, 4 20068 Peschiera Borromeo (MI) Tel.: +39 02 5167 2813 Fax: +39 02 5167 2459 E-mail: luigi.mantellini(a)idf-hit.com

1 0

[U-Boot-Users] help - u-boot header & compression
by Avinash Vijayvergia 02 Apr '08

02 Apr '08

Hi All I am working on AT91SAM9260 ARM9 core. I have very smallflash memory and hence need to compress the u-boot. I have picked nrv2balgo for that. Can someone suggest me how to put the compression infoin the u-boot header. I want to know the details of u-boot header too. Thanks Avinash ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost. http://tc.deals.yahoo.com/tc/blockbuster/text5.com

2 1

[U-Boot-Users] [ERR] U-Boot-Users Digest, Vol 23, Issue 11
by postmaster＠paran.com 02 Apr '08

02 Apr '08

Transmit Report: To: jaagar(a)paran.com, 2008/04/03 04:16:04, 451, Requested action aborted: No failover server

1 0