April 2008 - U-Boot

[U-Boot-Users] how to make a standalone linux device
by Avinash Vijayvergia 23 Apr '08

23 Apr '08

Hi I am working on AT91SAM9260EK eval board from atmel. I have been using uboot to load an NFS root file system on a Linux server. I need to load the linux kernel to the dataflash to make it standalone product. Can someone help me with the "how to" for it? Thanks Avinash ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ

1 0

[U-Boot-Users] ppc4xx: gpio setup broken for ppc405ep
by M B 23 Apr '08

23 Apr '08

Hi, I found some bugs for the gpio setup for ppc405ep and was about to fix them. After i fixed them (for 405ep) I realised that it's rather impossible to have a function like gpio_set_chip_configuration to setup the gpios for all ppc4xx, without turning it into ifdef hell. Even worse you can't even have one which only takes care of the ppc440ep. Maybe I misunderstood the datasheet of the ppc440ep, so please correct me if I'm wrong. According to Table 29-6 on page 687 which lists the registers for the alternate1 function the tsrl bits for gpio 12 have to be 01, but for gpio 13 they have to be 00. Both are inputs and both are alt1, so I don't see how to find a rule to decide what value has to be set. It's no big deal to have such a function for the ppc405ep and some others, but it should be obvious to see for what processors this function was tested and should fail with #error else. The Bugs I've found: 1. The addresses of the select registers (input/output/3state), which are defined in gpio.h of the ppc405ep are wrong. The address of the low register is 4 bytes higher than the high register. Furthermore GPIOs 0-16 are managed by the high register. Because the meaning and the address of the registers have changed, gpios 0-16 can be configured, which makes spotting this bug more difficult. 2. config_gpio assumes the address of the high register to be 4 bytes above the low register, which isn't the case for 405ep. 3. gpio_set_chip_configuration also assumes the address of the high register to be 4 bytes above the low register. 3.1 Furthermore the 3state select registers will get set, which should always be 00 for the 405ep. 3.2 The TCR register bits will only get set for gpio_out && gpio_sel, but they must be set for all outputs on 405ep. 4. The taihu board (405ep) uses gpio_set_chip_configuration. This bugs probably could have been avoided if the addresses of the registers would have been defined with #else #error, at least we would have a scapegoat now, who defined the wrong addresses. So why not add this rule to the coding style? Because no 405ep board uses config_gpio and only taihu uses gpio_set_chip_configuration, I think it would be best to undef this error prone functions and registers for 405ep. The registers defined in ppc405.h are correct, so most boards are o.k. anyway. I would have a patch for the registers and config_gpio, so if you don't agree with my solution I can submit it. Regards Markus

3 8

Re: [U-Boot-Users] AMCC PPC440EPx/sequoia stability question...
by Mike Nuss 23 Apr '08

23 Apr '08

Stefan wrote: > > > > At this point all possibilities are on the table and I'm > looking for any > > input from anyone with experience (good, bad, or whatever) with this > > processor and/or designs similar to the Sequoia. > > If you scan the U-Boot mailing list for 440EPx/Denali DDR2 > problems, you will > most likely find some references. I definitely recommend using the latest U-Boot with the SPD-based Denali code, if you're using DIMM modules. A smoking gun for us was the timing of the address clocking. Look at the lines on a scope; you may find that the clock is hitting too soon (before the address is stable). (If so, you'll need to delay the clock on your board.) Hope this helps, Mike

1 0

[U-Boot-Users] [PATCH 1/2] Add the Harris QUAD100HD AMCC 405EP-based board.
by Gary Jennejohn 23 Apr '08

23 Apr '08

Add the Harris QUAD100HD AMCC 405EP-based board. Signed-off-by: Gary Jennejohn <garyj(a)denx.de> --- MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + board/quad100hd/Makefile | 51 ++ board/quad100hd/config.mk | 24 + board/quad100hd/flash.c | 1097 +++++++++++++++++++++++++++++++++++++++++++ board/quad100hd/nand.c | 156 ++++++ board/quad100hd/quad100hd.c | 113 +++++ board/quad100hd/u-boot.lds | 133 ++++++ include/configs/quad100hd.h | 306 ++++++++++++ 10 files changed, 1888 insertions(+), 0 deletions(-) create mode 100644 board/quad100hd/Makefile create mode 100644 board/quad100hd/config.mk create mode 100644 board/quad100hd/flash.c create mode 100644 board/quad100hd/nand.c create mode 100644 board/quad100hd/quad100hd.c create mode 100644 board/quad100hd/u-boot.lds create mode 100644 include/configs/quad100hd.h diff --git a/MAINTAINERS b/MAINTAINERS index d1782b4..3af55a3 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -204,6 +204,10 @@ Klaus Heydeck <heydeck(a)kieback-peter.de> KUP4K MPC855 KUP4X MPC859 +Gary Jennejohn <garyj(a)denx.de> + + quad100hd PPC405EP + Murray Jensen <Murray.Jensen(a)csiro.au> cogent_mpc8xx MPC8xx diff --git a/MAKEALL b/MAKEALL index 8241f45..31e4866 100755 --- a/MAKEALL +++ b/MAKEALL @@ -218,6 +218,7 @@ LIST_4xx=" \ PMC405 \ PMC440 \ PPChameleonEVB \ + quad100hd \ rainier \ sbc405 \ sc3 \ diff --git a/Makefile b/Makefile index ab56831..8b3a7f0 100644 --- a/Makefile +++ b/Makefile @@ -1386,6 +1386,9 @@ PPChameleonEVB_HI_33_config: unconfig } @$(MKCONFIG) -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave +quad100hd_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx quad100hd + sbc405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx sbc405 diff --git a/board/quad100hd/Makefile b/board/quad100hd/Makefile new file mode 100644 index 0000000..1f79eae --- /dev/null +++ b/board/quad100hd/Makefile @@ -0,0 +1,51 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o nand.o flash.o +SOBJS = + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/quad100hd/config.mk b/board/quad100hd/config.mk new file mode 100644 index 0000000..71c0476 --- /dev/null +++ b/board/quad100hd/config.mk @@ -0,0 +1,24 @@ +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TEXT_BASE = 0xFFF80000 diff --git a/board/quad100hd/flash.c b/board/quad100hd/flash.c new file mode 100644 index 0000000..c3a034f --- /dev/null +++ b/board/quad100hd/flash.c @@ -0,0 +1,1097 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Modified 4/5/2001 + * Wait for completion of each sector erase command issued + * 4/5/2001 + * Chris Hallinan - DS4.COM, Inc. - clh(a)net1plus.com + */ + +#include <common.h> +#include <ppc4xx.h> +#include <asm/processor.h> + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +#undef DEBUG +#ifdef DEBUG +#define DEBUGF(x...) printf(x) +#else +#define DEBUGF(x...) +#endif /* DEBUG */ + +#ifdef FLASH_BASE1_PRELIM +#define CFG_FLASH_CHAR_SIZE unsigned char +#define CFG_FLASH_CHAR_ADDR0 (0x0555) +#define CFG_FLASH_CHAR_ADDR1 (0x02aa) +#endif +/*----------------------------------------------------------------------- + * Functions + */ +static ulong flash_get_size(vu_long * addr, flash_info_t * info); +static void flash_get_offsets(ulong base, flash_info_t * info); +static int write_word(flash_info_t * info, ulong dest, ulong data); +#ifdef FLASH_BASE1_PRELIM +static int write_word_1(flash_info_t * info, ulong dest, ulong data); +static int write_word_2(flash_info_t * info, ulong dest, ulong data); +static int flash_erase_1(flash_info_t * info, int s_first, int s_last); +static int flash_erase_2(flash_info_t * info, int s_first, int s_last); +static ulong flash_get_size_1(vu_long * addr, flash_info_t * info); +static ulong flash_get_size_2(vu_long * addr, flash_info_t * info); +#endif + +unsigned long flash_init(void) +{ + unsigned long size_b0, size_b1=0; + int i; + + /* Init: no FLASHes known */ + for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) { + flash_info[i].flash_id = FLASH_UNKNOWN; + } + + /* Static FLASH Bank configuration here - FIXME XXX */ + + size_b0 = + flash_get_size((vu_long *) FLASH_BASE0_PRELIM, &flash_info[0]); + + if (flash_info[0].flash_id == FLASH_UNKNOWN) { + printf("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n", + size_b0, size_b0 << 20); + } + + if (size_b0) { + /* Setup offsets */ + flash_get_offsets(FLASH_BASE0_PRELIM, &flash_info[0]); + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + CFG_MONITOR_BASE, + CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1, + &flash_info[0]); +#ifdef CFG_ENV_IS_IN_FLASH + (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR, + CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1, + &flash_info[0]); + (void)flash_protect(FLAG_PROTECT_SET, CFG_ENV_ADDR_REDUND, + CFG_ENV_ADDR_REDUND + CFG_ENV_SECT_SIZE - 1, + &flash_info[0]); +#endif + /* Also protect sector containing initial power-up instruction */ + /* (flash_protect() checks address range - other call ignored) */ + (void)flash_protect(FLAG_PROTECT_SET, + 0xFFFFFFFC, 0xFFFFFFFF, &flash_info[0]); + + flash_info[0].size = size_b0; + } +#ifdef FLASH_BASE1_PRELIM + size_b1 = + flash_get_size((vu_long *) FLASH_BASE1_PRELIM, &flash_info[1])*2; + + if (flash_info[1].flash_id == FLASH_UNKNOWN) { + printf("## Unknown FLASH on Bank 1 - Size = 0x%08lx = %ld MB\n", + size_b1, size_b1 << 20); + } + + if (size_b1) { + /* Setup offsets */ + flash_get_offsets(FLASH_BASE1_PRELIM, &flash_info[1]); + flash_info[1].size = size_b1; + } +#endif + return (size_b0 + size_b1); +} + +static void flash_get_offsets(ulong base, flash_info_t * info) +{ + int i; + + /* set up sector start address table */ + if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) || + (info->flash_id == FLASH_AM040)) { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00010000); + } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMLV128U) { + for (i = 0; i < info->sector_count; i++) { + info->start[i] = base + (i * 0x00010000*2); + } + } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_S29GL128N ) { + for (i = 0; i < info->sector_count; i++) { + info->start[i] = base + (i * 0x00020000*2); + } + } else { + if (info->flash_id & FLASH_BTYPE) { + /* set sector offsets for bottom boot block type */ + info->start[0] = base + 0x00000000; + info->start[1] = base + 0x00004000; + info->start[2] = base + 0x00006000; + info->start[3] = base + 0x00008000; + for (i = 4; i < info->sector_count; i++) { + info->start[i] = + base + (i * 0x00010000) - 0x00030000; + } + } else { + /* set sector offsets for top boot block type */ + i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00004000; + info->start[i--] = base + info->size - 0x00006000; + info->start[i--] = base + info->size - 0x00008000; + for (; i >= 0; i--) { + info->start[i] = base + i * 0x00010000; + } + } + } +} + + +void flash_print_info(flash_info_t * info) +{ + int i; + int k; + int size; + int erased; + volatile unsigned long *flash; + + if (info->flash_id == FLASH_UNKNOWN) { + printf("missing or unknown FLASH type\n"); + return; + } + + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_AMD: + printf("AMD "); + break; + case FLASH_MAN_STM: + printf("STM "); + break; + case FLASH_MAN_FUJ: + printf("FUJITSU "); + break; + case FLASH_MAN_SST: + printf("SST "); + break; + default: + printf("Unknown Vendor "); + break; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_AM040: + printf("AM29F040 (512 Kbit, uniform sector size)\n"); + break; + case FLASH_AM400B: + printf("AM29LV400B (4 Mbit, bottom boot sect)\n"); + break; + case FLASH_AM400T: + printf("AM29LV400T (4 Mbit, top boot sector)\n"); + break; + case FLASH_AM800B: + printf("AM29LV800B (8 Mbit, bottom boot sect)\n"); + break; + case FLASH_AM800T: + printf("AM29LV800T (8 Mbit, top boot sector)\n"); + break; + case FLASH_AMD016: + printf("AM29F016D (16 Mbit, uniform sector size)\n"); + break; + case FLASH_AM160B: + printf("AM29LV160B (16 Mbit, bottom boot sect)\n"); + break; + case FLASH_AM160T: + printf("AM29LV160T (16 Mbit, top boot sector)\n"); + break; + case FLASH_AM320B: + printf("AM29LV320B (32 Mbit, bottom boot sect)\n"); + break; + case FLASH_AM320T: + printf("AM29LV320T (32 Mbit, top boot sector)\n"); + break; + case FLASH_AM033C: + printf("AM29LV033C (32 Mbit, top boot sector)\n"); + break; + case FLASH_AMLV128U: + printf("AM29LV128U (128 Mbit * 2, top boot sector)\n"); + break; + case FLASH_SST800A: + printf("SST39LF/VF800 (8 Mbit, uniform sector size)\n"); + break; + case FLASH_SST160A: + printf("SST39LF/VF160 (16 Mbit, uniform sector size)\n"); + break; + case FLASH_STMW320DT: + printf ("M29W320DT (32 M, top sector)\n"); + break; + case FLASH_S29GL128N: + printf ("S29GL128N (256 Mbit, uniform sector size)\n"); + break; + default: + printf("Unknown Chip Type\n"); + break; + } + + printf(" Size: %ld KB in %d Sectors\n", + info->size >> 10, info->sector_count); + + printf(" Sector Start Addresses:"); + for (i = 0; i < info->sector_count; ++i) { + /* + * Check if whole sector is erased + */ + if (i != (info->sector_count - 1)) + size = info->start[i + 1] - info->start[i]; + else + size = info->start[0] + info->size - info->start[i]; + erased = 1; + flash = (volatile unsigned long *)info->start[i]; + size = size >> 2; /* divide by 4 for longword access */ + for (k = 0; k < size; k++) { + if (*flash++ != 0xffffffff) { + erased = 0; + break; + } + } + + if ((i % 5) == 0) + printf("\n "); + printf(" %08lX%s%s", + info->start[i], + erased ? " E" : " ", info->protect[i] ? "RO " : " "); + } + printf("\n"); + return; +} + + +/* + * The following code cannot be run from FLASH! + */ +#ifdef FLASH_BASE1_PRELIM +static ulong flash_get_size(vu_long * addr, flash_info_t * info) +{ + if ((ulong)addr == FLASH_BASE1_PRELIM) { + return flash_get_size_2(addr, info); + } else { + return flash_get_size_1(addr, info); + } +} + +static ulong flash_get_size_1(vu_long * addr, flash_info_t * info) +#else +static ulong flash_get_size(vu_long * addr, flash_info_t * info) +#endif +{ + short i; + CFG_FLASH_WORD_SIZE value; + ulong base = (ulong) addr; + volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr; + + DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr); + + /* Write auto select command: read Manufacturer ID */ + addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA; + addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055; + addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00900090; + udelay(1000); + + value = addr2[0]; + DEBUGF("FLASH MANUFACT: %x\n", value); + + switch (value) { + case (CFG_FLASH_WORD_SIZE) AMD_MANUFACT: + info->flash_id = FLASH_MAN_AMD; + break; + case (CFG_FLASH_WORD_SIZE) FUJ_MANUFACT: + info->flash_id = FLASH_MAN_FUJ; + break; + case (CFG_FLASH_WORD_SIZE) SST_MANUFACT: + info->flash_id = FLASH_MAN_SST; + break; + case (CFG_FLASH_WORD_SIZE) STM_MANUFACT: + info->flash_id = FLASH_MAN_STM; + break; + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + return 0; /* no or unknown flash */ + } + + value = addr2[1]; /* device ID */ + DEBUGF("\nFLASH DEVICEID: %x\n", value); + + switch (value) { + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + + case (CFG_FLASH_WORD_SIZE) AMD_ID_F040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + + case (CFG_FLASH_WORD_SIZE) STM_ID_M29W040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + + case (CFG_FLASH_WORD_SIZE) AMD_ID_F016D: + info->flash_id += FLASH_AMD016; + info->sector_count = 32; + info->size = 0x00200000; + break; /* => 2 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV033C: + info->flash_id += FLASH_AMDLV033C; + info->sector_count = 64; + info->size = 0x00400000; + break; /* => 4 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400T: + info->flash_id += FLASH_AM400T; + info->sector_count = 11; + info->size = 0x00080000; + break; /* => 0.5 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV400B: + info->flash_id += FLASH_AM400B; + info->sector_count = 11; + info->size = 0x00080000; + break; /* => 0.5 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800T: + info->flash_id += FLASH_AM800T; + info->sector_count = 19; + info->size = 0x00100000; + break; /* => 1 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV800B: + info->flash_id += FLASH_AM800B; + info->sector_count = 19; + info->size = 0x00100000; + break; /* => 1 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160T: + info->flash_id += FLASH_AM160T; + info->sector_count = 35; + info->size = 0x00200000; + break; /* => 2 MB */ + + case (CFG_FLASH_WORD_SIZE) AMD_ID_LV160B: + info->flash_id += FLASH_AM160B; + info->sector_count = 35; + info->size = 0x00200000; + break; /* => 2 MB */ + case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320T: + info->flash_id += FLASH_AM320T; + info->sector_count = 67; + info->size = 0x00400000; + break; /* => 4 MB */ + + case (CFG_FLASH_WORD_SIZE)AMD_ID_LV320B: + info->flash_id += FLASH_AM320B; + info->sector_count = 67; + info->size = 0x00400000; + break; /* => 4 MB */ + + default: + info->flash_id = FLASH_UNKNOWN; + return 0; /* => no or unknown flash */ + } + + /* set up sector start address table */ + if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00010000); + } + else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMLV128U) { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00010000 * 2); + } else { + if (info->flash_id & FLASH_BTYPE) { + /* set sector offsets for bottom boot block type */ + info->start[0] = base + 0x00000000; + info->start[1] = base + 0x00004000; + info->start[2] = base + 0x00006000; + info->start[3] = base + 0x00008000; + for (i = 4; i < info->sector_count; i++) { + info->start[i] = + base + (i * 0x00010000) - 0x00030000; + } + } else { + /* set sector offsets for top boot block type */ + i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00004000; + info->start[i--] = base + info->size - 0x00006000; + info->start[i--] = base + info->size - 0x00008000; + for (; i >= 0; i--) { + info->start[i] = base + i * 0x00010000; + } + } + } + + /* check for protected sectors */ + for (i = 0; i < info->sector_count; i++) { + /* read sector protection at sector address, (A7 .. A0) = 0x02 */ + /* D0 = 1 if protected */ + addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]); + + /* For AMD29033C flash we need to resend the command of * + * reading flash protection for upper 8 Mb of flash */ + if (i == 32) { + addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090; + } + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) + info->protect[i] = 0; + else + info->protect[i] = addr2[2] & 1; + } + + /* issue bank reset to return to read mode */ + addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0; + + return info->size; +} + +static int wait_for_DQ7_1(flash_info_t * info, int sect) +{ + ulong start, now, last; + volatile CFG_FLASH_WORD_SIZE *addr = + (CFG_FLASH_WORD_SIZE *) (info->start[sect]); + + start = get_timer(0); + last = start; + while ((addr[0] & (CFG_FLASH_WORD_SIZE) 0x00800080) != + (CFG_FLASH_WORD_SIZE) 0x00800080) { + if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) { + printf("Timeout\n"); + return -1; + } + /* show that we're waiting */ + if ((now - last) > 1000) { /* every second */ + putc('.'); + last = now; + } + } + return 0; +} + +#ifdef FLASH_BASE1_PRELIM +int flash_erase(flash_info_t * info, int s_first, int s_last) +{ + if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMLV128U) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_S29GL128N) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT)) { + return flash_erase_2(info, s_first, s_last); + } else { + return flash_erase_1(info, s_first, s_last); + } +} + +static int flash_erase_1(flash_info_t * info, int s_first, int s_last) +#else +int flash_erase(flash_info_t * info, int s_first, int s_last) +#endif +{ + volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]); + volatile CFG_FLASH_WORD_SIZE *addr2; + int flag, prot, sect, l_sect; + int i; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf("- missing\n"); + } else { + printf("- no sectors to erase\n"); + } + return 1; + } + + if (info->flash_id == FLASH_UNKNOWN) { + printf("Can't erase unknown flash type - aborted\n"); + return 1; + } + + prot = 0; + for (sect = s_first; sect <= s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) { + printf("- Warning: %d protected sectors will not be erased!\n", + prot); + } else { + printf("\n"); + } + + l_sect = -1; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect <= s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]); + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) { + addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA; + addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055; + addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080; + addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA; + addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055; + addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00500050; /* block erase */ + for (i = 0; i < 50; i++) + udelay(1000); /* wait 1 ms */ + } else { + addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA; + addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055; + addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00800080; + addr[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA; + addr[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055; + addr2[0] = (CFG_FLASH_WORD_SIZE) 0x00300030; /* sector erase */ + } + l_sect = sect; + /* + * Wait for each sector to complete, it's more + * reliable. According to AMD Spec, you must + * issue all erase commands within a specified + * timeout. This has been seen to fail, especially + * if printf()s are included (for debug)!! + */ + wait_for_DQ7_1(info, sect); + } + } + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* wait at least 80us - let's wait 1 ms */ + udelay(1000); + + /* reset to read mode */ + addr = (CFG_FLASH_WORD_SIZE *) info->start[0]; + addr[0] = (CFG_FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ + + printf(" done\n"); + return 0; +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + ulong cp, wp, data; + int i, l, rc; + + wp = (addr & ~3); /* get lower word aligned address */ + + /* + * handle unaligned start bytes + */ + if ((l = addr - wp) != 0) { + data = 0; + for (i = 0, cp = wp; i < l; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + for (; i < 4 && cnt > 0; ++i) { + data = (data << 8) | *src++; + --cnt; + ++cp; + } + for (; cnt == 0 && i < 4; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + if ((rc = write_word(info, wp, data)) != 0) { + return rc; + } + wp += 4; + } + + /* + * handle word aligned part + */ + while (cnt >= 4) { + data = 0; + for (i = 0; i < 4; ++i) { + data = (data << 8) | *src++; + } + if ((rc = write_word(info, wp, data)) != 0) { + return rc; + } + wp += 4; + cnt -= 4; + } + + if (cnt == 0) { + return 0; + } + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) { + data = (data << 8) | *src++; + --cnt; + } + for (; i < 4; ++i, ++cp) { + data = (data << 8) | (*(uchar *) cp); + } + + return (write_word(info, wp, data)); +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +#ifdef FLASH_BASE1_PRELIM +static int write_word(flash_info_t * info, ulong dest, ulong data) +{ + if (((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320B) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM320T) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMLV128U) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_S29GL128N) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_STMW320DT)) { + return write_word_2(info, dest, data); + } else { + return write_word_1(info, dest, data); + } +} + +static int write_word_1(flash_info_t * info, ulong dest, ulong data) +#else +static int write_word(flash_info_t * info, ulong dest, ulong data) +#endif +{ + volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]); + volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest; + volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data; + ulong start; + int i; + + /* Check if Flash is (sufficiently) erased */ + if ((*((vu_long *)dest) & data) != data) { + return 2; + } + + for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) { + int flag; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00AA00AA; + addr2[CFG_FLASH_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x00550055; + addr2[CFG_FLASH_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x00A000A0; + + dest2[i] = data2[i]; + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* data polling for D7 */ + start = get_timer(0); + while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080) != + (data2[i] & (CFG_FLASH_WORD_SIZE) 0x00800080)) { + + if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { + return 1; + } + } + } + + return 0; +} + +#ifdef FLASH_BASE1_PRELIM + +/* + * The following code cannot be run from FLASH! + */ +static ulong flash_get_size_2(vu_long * addr, flash_info_t * info) +{ + short i; + CFG_FLASH_CHAR_SIZE value; + ulong base = (ulong) addr; + volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) addr; + + DEBUGF("FLASH ADDR: %08x\n", (unsigned)addr); + + /* Write auto select command: read Manufacturer ID */ + addr2[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr2[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr2[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090; + udelay(1000); + + value = (CFG_FLASH_CHAR_SIZE)addr2[0]; + DEBUGF("FLASH MANUFACT: %x\n", value); + + switch (value) { + case (CFG_FLASH_CHAR_SIZE) AMD_MANUFACT: + info->flash_id = FLASH_MAN_AMD; + break; + case (CFG_FLASH_CHAR_SIZE) FUJ_MANUFACT: + info->flash_id = FLASH_MAN_FUJ; + break; + case (CFG_FLASH_CHAR_SIZE) SST_MANUFACT: + info->flash_id = FLASH_MAN_SST; + break; + case (CFG_FLASH_CHAR_SIZE) STM_MANUFACT: + info->flash_id = FLASH_MAN_STM; + break; + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + return 0; /* no or unknown flash */ + } + + value = (CFG_FLASH_CHAR_SIZE)addr2[2]; /* device ID */ + DEBUGF("\nFLASH DEVICEID: %x\n", value); + + switch (value) { + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_F040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + + case (CFG_FLASH_CHAR_SIZE) STM_ID_M29W040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 512 ko */ + break; + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_F016D: + info->flash_id += FLASH_AMD016; + info->sector_count = 32; + info->size = 0x00200000; + break; /* => 2 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV033C: + info->flash_id += FLASH_AMDLV033C; + info->sector_count = 64; + info->size = 0x00400000; + break; /* => 4 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV400T: + info->flash_id += FLASH_AM400T; + info->sector_count = 11; + info->size = 0x00080000; + break; /* => 0.5 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV400B: + info->flash_id += FLASH_AM400B; + info->sector_count = 11; + info->size = 0x00080000; + break; /* => 0.5 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV800T: + info->flash_id += FLASH_AM800T; + info->sector_count = 19; + info->size = 0x00100000; + break; /* => 1 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV800B: + info->flash_id += FLASH_AM800B; + info->sector_count = 19; + info->size = 0x00100000; + break; /* => 1 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV160T: + info->flash_id += FLASH_AM160T; + info->sector_count = 35; + info->size = 0x00200000; + break; /* => 2 MB */ + + case (CFG_FLASH_CHAR_SIZE) AMD_ID_LV160B: + info->flash_id += FLASH_AM160B; + info->sector_count = 35; + info->size = 0x00200000; + break; /* => 2 MB */ + case (CFG_FLASH_CHAR_SIZE) AMD_ID_MIRROR: + if ((CFG_FLASH_CHAR_SIZE)addr2[0x1c] == (CFG_FLASH_CHAR_SIZE)AMD_ID_LV128U_2 + && (CFG_FLASH_CHAR_SIZE)addr2[0x1e] == (CFG_FLASH_CHAR_SIZE)AMD_ID_LV128U_3) { + info->flash_id += FLASH_AMLV128U; + info->sector_count = 256; + info->size = 0x01000000; + } else if ((CFG_FLASH_CHAR_SIZE)addr2[0x1c] == (CFG_FLASH_CHAR_SIZE)AMD_ID_GL128N_2 + && (CFG_FLASH_CHAR_SIZE)addr2[0x1e] == (CFG_FLASH_CHAR_SIZE)AMD_ID_GL128N_3 ) { + info->flash_id += FLASH_S29GL128N; + info->sector_count = 128; + info->size = 0x01000000; + } + else + info->flash_id = FLASH_UNKNOWN; + break; /* => 2 MB */ + + default: + info->flash_id = FLASH_UNKNOWN; + return 0; /* => no or unknown flash */ + } + + /* set up sector start address table */ + if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) || + ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMD016)) { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00 010000); + } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AMLV128U) { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00010000); + } else if ((info->flash_id & FLASH_TYPEMASK) == FLASH_S29GL128N ) { + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * 0x00020000); + } else { + if (info->flash_id & FLASH_BTYPE) { + /* set sector offsets for bottom boot block type */ + info->start[0] = base + 0x00000000; + info->start[1] = base + 0x00004000; + info->start[2] = base + 0x00006000; + info->start[3] = base + 0x00008000; + for (i = 4; i < info->sector_count; i++) { + info->start[i] = + base + (i * 0x00010000) - 0x00030000; + } + } else { + /* set sector offsets for top boot block type */ + i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00004000; + info->start[i--] = base + info->size - 0x00006000; + info->start[i--] = base + info->size - 0x00008000; + for (; i >= 0; i--) { + info->start[i] = base + i * 0x00010000; + } + } + } + + /* check for protected sectors */ + for (i = 0; i < info->sector_count; i++) { + /* read sector protection at sector address, (A7 .. A0) = 0x02 */ + /* D0 = 1 if protected */ + addr2 = (volatile CFG_FLASH_WORD_SIZE *)(info->start[i]); + + /* For AMD29033C flash we need to resend the command of * + * reading flash protection for upper 8 Mb of flash */ + if (i == 32) { + addr2[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr2[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr2[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x90909090; + } + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) + info->protect[i] = 0; + else + info->protect[i] = (CFG_FLASH_CHAR_SIZE)addr2[4] & 1; + } + + /* issue bank reset to return to read mode */ + addr2[0] = (CFG_FLASH_WORD_SIZE) 0xF0F0F0F0; + return info->size; +} + +static int wait_for_DQ7_2(flash_info_t * info, int sect) +{ + ulong start, now, last; + volatile CFG_FLASH_WORD_SIZE *addr = + (CFG_FLASH_WORD_SIZE *) (info->start[sect]); + + start = get_timer(0); + last = start; + while (((CFG_FLASH_WORD_SIZE)addr[0] & (CFG_FLASH_WORD_SIZE) 0x80808080) != + (CFG_FLASH_WORD_SIZE) 0x80808080) { + if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) { + printf("Timeout\n"); + return -1; + } + /* show that we're waiting */ + if ((now - last) > 1000) { /* every second */ + putc('.'); + last = now; + } + } + return 0; +} + +static int flash_erase_2(flash_info_t * info, int s_first, int s_last) +{ + volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]); + volatile CFG_FLASH_WORD_SIZE *addr2; + int flag, prot, sect, l_sect; + int i; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf("- missing\n"); + } else { + printf("- no sectors to erase\n"); + } + return 1; + } + + if (info->flash_id == FLASH_UNKNOWN) { + printf("Can't erase unknown flash type - aborted\n"); + return 1; + } + + prot = 0; + for (sect = s_first; sect <= s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) { + printf("- Warning: %d protected sectors will not be erased!\n", + prot); + } else { + printf("\n"); + } + + l_sect = -1; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect <= s_last; sect++) { + if (info->protect[sect] == 0) { /* not protected */ + addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]); + + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) { + addr[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x80808080; + addr[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr2[0] = (CFG_FLASH_WORD_SIZE) 0x50505050; /* block erase */ + for (i = 0; i < 50; i++) + udelay(1000); /* wait 1 ms */ + } else { + addr[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0x80808080; + addr[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr2[0] = (CFG_FLASH_WORD_SIZE) 0x30303030; /* sector erase */ + } + l_sect = sect; + /* + * Wait for each sector to complete, it's more + * reliable. According to AMD Spec, you must + * issue all erase commands within a specified + * timeout. This has been seen to fail, especially + * if printf()s are included (for debug)!! + */ + wait_for_DQ7_2(info, sect); + } + } + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* wait at least 80us - let's wait 1 ms */ + udelay(1000); + + /* reset to read mode */ + addr = (CFG_FLASH_WORD_SIZE *) info->start[0]; + addr[0] = (CFG_FLASH_WORD_SIZE) 0xF0F0F0F0; /* reset bank */ + + printf(" done\n"); + return 0; +} + +static int write_word_2(flash_info_t * info, ulong dest, ulong data) +{ + volatile CFG_FLASH_WORD_SIZE *addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[0]); + volatile CFG_FLASH_WORD_SIZE *dest2 = (CFG_FLASH_WORD_SIZE *) dest; + volatile CFG_FLASH_WORD_SIZE *data2 = (CFG_FLASH_WORD_SIZE *) & data; + ulong start; + int i; + + /* Check if Flash is (sufficiently) erased */ + if ((*((vu_long *)dest) & data) != data) { + return 2; + } + + for (i = 0; i < 4 / sizeof(CFG_FLASH_WORD_SIZE); i++) { + int flag; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + addr2[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xAAAAAAAA; + addr2[CFG_FLASH_CHAR_ADDR1] = (CFG_FLASH_WORD_SIZE) 0x55555555; + addr2[CFG_FLASH_CHAR_ADDR0] = (CFG_FLASH_WORD_SIZE) 0xA0A0A0A0; + + dest2[i] = data2[i]; + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* data polling for D7 */ + start = get_timer(0); + while ((dest2[i] & (CFG_FLASH_WORD_SIZE) 0x80808080) != + (data2[i] & (CFG_FLASH_WORD_SIZE) 0x80808080)) { + + if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { + return 1; + } + } + } + + return 0; +} + +#endif /* FLASH_BASE1_PRELIM */ --- Gary Jennejohn ********************************************************************* DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office(a)denx.de *********************************************************************

1 0

[U-Boot-Users] intended behavior of bootm
by Matthias Fuchs 23 Apr '08

23 Apr '08

Hi, I am wondering if bootm behaves correctly on CRC errors in kernel and/or ramdisk images. This is what I observed: 1) I loaded a Linux kernel into RAM at 0x200000 on a 405 system. I loaded an initial ramdisk images into RAM at address 0x300000. Now 'bootm 200000 300000' boots my system correctly. 2) Same loading as above. But I made the kernel image CRC check fail (mw 220000 12345678). I get: ... Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! => That's ok. 3) Same loading as above. But I make the ramdisk CRC check fail (mw 320000 12345678). I get: ## Booting kernel from Legacy Image at 00200000 ... ... ## Loading init Ramdisk from Legacy Image at 00300000 ... ... Verifying Checksum ... Bad Data CRC <system reset> U-Boot 1.3.2-00450-g77dd47f (Apr 21 2008 - 14:43:23) Hmm, I expected the same behavior as for a corrupted kernel image. So what should be the correct behavior? I would like to get back to the prompt on any CRC error. So is this a bug? Matthias

3 8

Re: [U-Boot-Users] [PATCH] ppc: Revert patch 70431e8a that used _start instead of CFG_MONITOR_BASE
by Kim Phillips 23 Apr '08

23 Apr '08

On Tue, 22 Apr 2008 07:49:57 +0200 "Joakim Tjernlund" <Joakim.Tjernlund(a)transmode.se> wrote: > > Currently WD's top of tree renders 83xx kaput. When I revert this > > revert plus Joakim's original 70431e8 commit, things are back to > > normal. I'm not going to pretend I know to fix it up correctly, so > > does anyone have a problem with me sending two revert patches until > > relocation is properly and comprehensively fixed? > > Strange, I got a 8321 and it worked for me. Maybe a toolchain issue? Perhaps > I got something extra in my board port, dunno what though. > I just reconfirmed it using WD's TOT w/gcc version 4.1.2 20070925 (Red Hat 4.1.2-27). Kim

2 1

[U-Boot-Users] Report to Recipient(s)
by ukmail01/srv/moog 23 Apr '08

23 Apr '08

Incident Information:- Originator: u-boot-users-bounces(a)lists.sourceforge.net Recipients: <trimarchi(a)gandalf.sssup.it>, u-boot-users(a)lists.sourceforge.net Subject: Re: [U-Boot-Users] USB SUPPORT Generic Alert: Exception was 'Unscannable File' scanning attachment 'u-boot-usb-bug.img.bz2'

1 0

[U-Boot-Users] mpc8313 nand setup
by Daniel 22 Apr '08

22 Apr '08

Hi All, I am working on a MPC8313ERDB REVA4 board and need to work with a nand device using u-boot. I am using u-boot version 1.3.2 and under the driver/mtd/nand directory there is a file called nand.c. In this file it makes a call to a function called board_nand_init(). From what I can tell this function is suppose to be located another nand.c file located in board/freescale/mpc8313erdb but it seems to be missing. I found this missing file on the website www.bitshrine.org/gpp/u-boot-1.1.6-mpc8313erdb-board.patch. But I haven't been able to get the source code (nand.c) to compile it (unless I comment out all errors of course). Any help would be greatly appreciated. Thanks

2 1

[U-Boot-Users] [PATCH] ppc4xx: Fix Canyonlands and Glacier default environment for fdt usage
by Stefan Roese 22 Apr '08

22 Apr '08

This patch fixes the Canyonlands and Glacier default environment to better fit to the arch/powerpc device-tree kernels. The variables dealing with arch/ppc booting are removed, since these boards are supported only in arch/powerpc. Glacier uses the same config file as Canyonlands. Also, the Glacier now uses non-FPU rootpath, since 460GT has no FPU. Signed-off-by: Stefan Roese <sr(a)denx.de> --- include/configs/canyonlands.h | 23 +++++++++++++---------- 1 files changed, 13 insertions(+), 10 deletions(-) diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index e7896aa..3dd577a 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -319,15 +319,18 @@ #define CONFIG_HOSTNAME canyonlands #define CFG_BOOTFILE "bootfile=canyonlands/uImage\0" #define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0" +#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" #else #define CONFIG_HOSTNAME glacier #define CFG_BOOTFILE "bootfile=glacier/uImage\0" #define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0" +#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" #endif #define CONFIG_EXTRA_ENV_SETTINGS \ CFG_BOOTFILE \ CFG_DTBFILE \ + CFG_ROOTPATH \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ @@ -336,18 +339,18 @@ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "net_nfs=tftp 400000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 400000 - ${fdt_addr}\0" \ - "net_nfs_fdt=net_nfs\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xxFP\0" \ - "fdt_addr=800000\0" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addtty;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=800000\0" \ "kernel_addr=fc000000\0" \ + "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ "initrd_high=30000000\0" \ "load=tftp 200000 ${hostname}/u-boot.bin\0" \ -- 1.5.5.1

1 0

Re: [U-Boot-Users] Programming ethernet PHY by SPI on MPC8360E-RDK
by David Saada 22 Apr '08

22 Apr '08

> I have been scouring the code (u-boot) to see evidence of using SPI to > configure the ethernet PHY. I do not find anything that is obvious. The > board uses BMC54XX ethernet transciever. I will appreciate any insight from > you . > I was able to locate and use QE configuration of IO pins. Many thanks. > Sampath Sorry, can't help you here. Maybe somoene from the u-boot list has better knowledge of this?

1 0