September 2007 - U-Boot

Re: [U-Boot-Users] Atmel AT49BV320C support in Uboot
by raj reddy 12 Sep '07

12 Sep '07

I tried to use the CFI driver by adding the CFI macros in the .h file. But the size of my flash is 2MB, but it shows 4MB. I have one doubt, in the board .h file we specify the sectore size. what size i must give the sector size in board .h file. where we specify different sizes of sector in the flash driver file.. (i.e 8 * 4K, 63 * 32 K.) Regards. --- Wolfgang Denk <wd(a)denx.de> wrote: > First: Please post U-Boot related questions to > the mailing list > *only* - unless you as ENX for commercial > support which we will > happily provide, but that's not for free. > > In message > <183967.9154.qm(a)web7711.mail.in.yahoo.com> you > wrote: > > CFI supports only the same size sector flash, but > > This is not correct. The CFI driver also supports > boot sector type > flash chips. > > > is't the right procedure what i am trying to add > the > > flash support for AT49BV320C > > If the flashis CFI conforming,then you should use > the CFI driver. > > Best regards, > > Wolfgang Denk > > -- > DENX Software Engineering GmbH, MD: Wolfgang > Denk & Detlev Zundel > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 > Groebenzell, Germany > Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 > Email: wd(a)denx.de > Computers are not intelligent. They only think they > are. > 5, 50, 500, 5000 - Store N number of mails in your inbox. Go to http://help.yahoo.com/l/in/yahoo/mail/yahoomail/tools/tools-08.html

4 7

[U-Boot-Users] [RFC] Configuration rework for next merge window
by Grant Likely 12 Sep '07

12 Sep '07

Wolfgang, When the next u-boot merge window opens, I'd like to merge in the build changes needed to support conditional compile. However, this will be an invasive change on the Makefiles so it requires some planning ahead. The most invasive change is splitting the COBJS definitions into one line per file which is sure to cause merge conflicts with other boards which I'd like to avoid. I see three possible approaches: 1. Merge the COBJS split into -testing now, and ask custodians to base there changes onto that before the merge window opens 2. Merge the COBJS split at the start of the merge window before any other patches are merged 3. Merge the COBJS split at the end of the merge window and let me deal with the conflicts. My preference is definitely #1, followed by #2. I think getting it in first will result in higher confidence that the change has not broken anything as each of the custodian trees will be testing against it before they request a pull. Plus, it's less work for me. :-) My other changes are far less invasive, but more risky. I'd like to get them into -testing also for the test factor, but merge conflicts shouldn't be much of an issue. Cheers, g. -- Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. grant.likely(a)secretlab.ca (403) 399-0195

4 6

[U-Boot-Users] Errors while executing 'make' for u-boot-1.1.6 for incaip board
by Verma 12 Sep '07

12 Sep '07

Hi , Errors are generated ,when I am trying to create the u-boot.bin for u-boot-1.1.6 version using the following commands. -make incaip_config -make / make all The errors generated are as follows:make[1]: Entering directory `/opt/u-boot-1.1.6/post/cpu' make[1]: Nothing to be done for `all'. make[1]: Leaving directory `/opt/u-boot-1.1.6/post/cpu' make -C common/ make[1]: Entering directory `/opt/u-boot-1.1.6/common' mips_4KC-gcc -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/opt/u-boot-1.1.6/include -fno-builtin -ffreestanding -nostdinc -isystem /usr/lib/gcc-lib/mips-linux/2.95.4/include -pipe -DCONFIG_MIPS -D__MIPS__ -mcpu=4kc -EB -mabicalls -Wall -Wstrict-prototypes -c -o cmd_bootm.o cmd_bootm.c cmd_bootm.c:477: warning: preprocessing directive not recognized within macro arg cmd_bootm.c:477: warning: preprocessing directive not recognized within macro arg cmd_bootm.c:469: undefined or invalid # directive cmd_bootm.c:475: undefined or invalid # directive make[1]: *** [cmd_bootm.o] Error 1 make[1]: Leaving directory `/opt/u-boot-1.1.6/common' make: *** [common/libcommon.a] Error 2 How can I avoid these errors, should I make any particular modifications to any of the Makefiles.Please let me know. Verma. -- View this message in context: http://www.nabble.com/Errors-while-executing-%27make%27-for-u-boot-1.1.6-fo… Sent from the Uboot - Users mailing list archive at Nabble.com.

2 1

[U-Boot-Users] [PATCH7] microblaze - ROMFS adapt files
by Michal Simek 11 Sep '07

11 Sep '07

DESC: ROMFS support files and sorted names in Makefiles Signed-off-by: Michal Simek <monstr(a)monstr.eu> Note; I think that we can start process with redesigning all FS support diff --git a/Makefile b/Makefile index 0477cd3..6d84dbb 100644 --- a/Makefile +++ b/Makefile @@ -201,8 +201,9 @@ ifeq ($(CPU),ixp) LIBS += cpu/ixp/npe/libnpe.a endif LIBS += lib_$(ARCH)/lib$(ARCH).a -LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a \ - fs/reiserfs/libreiserfs.a fs/ext2/libext2fs.a +LIBS += fs/cramfs/libcramfs.a fs/ext2/libext2fs.a fs/fat/libfat.a \ + fs/fdos/libfdos.a fs/jffs2/libjffs2.a fs/reiserfs/libreiserfs.a \ + fs/romfs/libromfs.a LIBS += net/libnet.a LIBS += disk/libdisk.a LIBS += rtc/librtc.a @@ -325,14 +326,14 @@ depend dep: tags ctags: ctags -w -o $(OBJTREE)/ctags `find $(SUBDIRS) include \ lib_generic board/$(BOARDDIR) cpu/$(CPU) lib_$(ARCH) \ - fs/cramfs fs/fat fs/fdos fs/jffs2 \ + fs/cramfs fs/fat fs/fdos fs/jffs2 fs/romfs\ net disk rtc dtt drivers drivers/sk98lin common \ $ -name CVS -prune $ -o $ -name '*.[ch]' -print $` etags: etags -a -o $(OBJTREE)/etags `find $(SUBDIRS) include \ lib_generic board/$(BOARDDIR) cpu/$(CPU) lib_$(ARCH) \ - fs/cramfs fs/fat fs/fdos fs/jffs2 \ + fs/cramfs fs/fat fs/fdos fs/jffs2 fs/romfs\ net disk rtc dtt drivers drivers/sk98lin common \ $ -name CVS -prune $ -o $ -name '*.[ch]' -print $` diff --git a/common/cmd_jffs2.c b/common/cmd_jffs2.c index 513a226..3e6061a 100644 --- a/common/cmd_jffs2.c +++ b/common/cmd_jffs2.c @@ -85,7 +85,7 @@ */ /* - * JFFS2/CRAMFS support + * JFFS2/CRAMFS/ROMFS support */ #include <common.h> #include <command.h> @@ -175,6 +175,11 @@ extern int cramfs_load (char *loadoffset, struct part_info *info, char *filename extern int cramfs_ls (struct part_info *info, char *filename); extern int cramfs_info (struct part_info *info); +extern int romfs_check (struct part_info *info); +extern int romfs_load (char *loadoffset, struct part_info *info, char *filename); +extern int romfs_ls (struct part_info *info, char *filename); +extern int romfs_info (struct part_info *info); + static struct part_info* jffs2_part_info(struct mtd_device *dev, unsigned int part_num); /* command line only routines */ @@ -1874,14 +1879,22 @@ int do_jffs2_fsload(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if ((part = jffs2_part_info(current_dev, current_partnum))){ - /* check partition type for cramfs */ - fsname = (cramfs_check(part) ? "CRAMFS" : "JFFS2"); + /* check partition type for JFFS2, cramfs, romfs */ + if (cramfs_check(part)) { + fsname = "CRAMFS"; + } else if (romfs_check(part)) { + fsname = "ROMFS"; + } else { + fsname = "JFFS2"; + } printf("### %s loading '%s' to 0x%lx\n", fsname, filename, offset); if (cramfs_check(part)) { size = cramfs_load ((char *) offset, part, filename); + } else if (romfs_check(part)){ + size = romfs_load ((char *) offset, part, filename); } else { - /* if this is not cramfs assume jffs2 */ + /* if this is not cramfs or romfs assume jffs2 */ size = jffs2_1pass_load((char *)offset, part, filename); } @@ -1928,8 +1941,10 @@ int do_jffs2_ls(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) /* check partition type for cramfs */ if (cramfs_check(part)) { ret = cramfs_ls (part, filename); + } else if (romfs_check(part)) { + ret = romfs_ls (part, filename); } else { - /* if this is not cramfs assume jffs2 */ + /* if this is not cramfs or romfs assume jffs2 */ ret = jffs2_1pass_ls(part, filename); } @@ -1951,7 +1966,6 @@ int do_jffs2_ls(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) int do_jffs2_fsinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { struct part_info *part; - char *fsname; int ret; /* make sure we are in sync with env variables */ @@ -1961,13 +1975,17 @@ int do_jffs2_fsinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if ((part = jffs2_part_info(current_dev, current_partnum))){ /* check partition type for cramfs */ - fsname = (cramfs_check(part) ? "CRAMFS" : "JFFS2"); - printf("### filesystem type is %s\n", fsname); + puts("### filesystem type is "); if (cramfs_check(part)) { + puts("CRAMFS\n"); ret = cramfs_info (part); + } else if (romfs_check(part)) { + puts("ROMFS\n"); + ret = romfs_info (part); } else { - /* if this is not cramfs assume jffs2 */ + /* if this is not cramfs or romfs assume jffs2 */ + puts("JFFS2\n"); ret = jffs2_1pass_info(part); } diff --git a/fs/Makefile b/fs/Makefile index 273d90e..2e5cf90 100644 --- a/fs/Makefile +++ b/fs/Makefile @@ -22,7 +22,7 @@ # # -SUBDIRS := jffs2 cramfs fdos fat reiserfs ext2 +SUBDIRS := cramfs ext2 fat fdos jffs2 reiserfs romfs $(obj).depend all: @for dir in $(SUBDIRS) ; do \

3 3

[U-Boot-Users] Merge Window Closed.
by Wolfgang Denk 11 Sep '07

11 Sep '07

Hi everybody. our first merge window has just ended. I think I have processed all pull requests and added all (recent) open patches. Please have a look and check if anything that should go into the next release and has been submitted before the deadline is still missing. Please find attached below the build errors resulting when running the "MAKEALL" script for the "arm", "mips" and "ppc" architectures. I used the ELDk 4.1 tool chain to do this, just in case it matters. * Please help testing by running MAKEALL for the other architectures for which I don't have tools and boards to test... * Board maintainers: please help clean up build errors on warnings on your boards. Please help testing and fixing so we can have a high quality code release at the end of this cycle. BTW: what should the next release be named - 1.2.1 or 1.3.0 ? Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de Faith may be defined briefly as an illogical belief in the occurence of the improbable. - H. L. Mencken

8 12

[U-Boot-Users] Atmel AT49BV320C support in Uboot
by raj reddy 11 Sep '07

11 Sep '07

Hi, Can any one help me, how to add support for the AT49BV320C (command Flash Interface) support for the uboot. Regards. Unlimited freedom, unlimited storage. Get it now, on http://help.yahoo.com/l/in/yahoo/mail/yahoomail/tools/tools-08.html/

2 3

[U-Boot-Users] U-Boot-1.3.0-rc1 released
by Wolfgang Denk 11 Sep '07

11 Sep '07

Hello, the first release candidate for U-Boot-1.3.0 is out. Please test it and help to clean up the remaining issues. PPC is in an acceptable state, but ARM and MIPS and others still need a lot of work... Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de Keep your head and your heart going in the right direction and you will not have to worry about your feet.

5 9

[U-Boot-Users] Microblaze
by Michal Simek 11 Sep '07

11 Sep '07

HI, that's all. The biggest problem was in configuration file for boards. But I made changes and especially configs file contains some parts of it. Best regards Michal Simek

2 3

[U-Boot-Users] Free NFL Game Tracker
by colunson＠fillmorefire.com 11 Sep '07

11 Sep '07

Are you ready for some football? Get all the information you need for every game. Get you data online everyday from our free game tracker: http://24.9.237.96/

1 0

[U-Boot-Users] [PATCH13] microblaze - xupv2p
by Michal Simek 11 Sep '07

11 Sep '07

DESC: clean Makefile, change configuration setting why? because XupV2p use new emac drivers Signed-off-by: Michal Simek <monstr(a)monstr.eu> diff --git a/board/xilinx/xupv2p/Makefile b/board/xilinx/xupv2p/Makefile index 9ab5633..99e7047 100644 --- a/board/xilinx/xupv2p/Makefile +++ b/board/xilinx/xupv2p/Makefile @@ -22,32 +22,17 @@ # include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -$(shell mkdir -p $(obj)../xilinx_enet) -endif - -INCS := -I../common -I../xilinx_enet -CFLAGS += $(INCS) -HOST_CFLAGS += $(INCS) LIB = $(obj)lib$(BOARD).a -COBJS = $(BOARD).o \ - ../xilinx_enet/emac_adapter.o ../xilinx_enet/xemac.o \ - ../xilinx_enet/xemac_options.o ../xilinx_enet/xemac_polled.o \ - ../xilinx_enet/xemac_intr.o ../xilinx_enet/xemac_g.o \ - ../xilinx_enet/xemac_intr_dma.o ../common/xipif_v1_23_b.o \ - ../common/xbasic_types.o ../common/xdma_channel.o \ - ../common/xdma_channel_sg.o ../common/xpacket_fifo_v1_00_b.o \ - ../common/xversion.o \ +COBJS = $(BOARD).o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) SOBJS := $(addprefix $(obj),$(SOBJS)) -$(LIB): $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $^ +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) clean: rm -f $(SOBJS) $(OBJS) diff --git a/board/xilinx/xupv2p/config.mk b/board/xilinx/xupv2p/config.mk index c07b0b3..eedfb24 100644 --- a/board/xilinx/xupv2p/config.mk +++ b/board/xilinx/xupv2p/config.mk @@ -25,8 +25,8 @@ # Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4 # -TEXT_BASE = 0x38000000 +TEXT_BASE = 0x30000000 +PLATFORM_CPPFLAGS += -mxl-pattern-compare PLATFORM_CPPFLAGS += -mno-xl-soft-mul -PLATFORM_CPPFLAGS += -mno-xl-soft-div -PLATFORM_CPPFLAGS += -mxl-barrel-shift +PLATFORM_CPPFLAGS += -mcpu=v5.00.c diff --git a/board/xilinx/xupv2p/xparameters.h b/board/xilinx/xupv2p/xparameters.h index a96c693..0bb7a80 100644 --- a/board/xilinx/xupv2p/xparameters.h +++ b/board/xilinx/xupv2p/xparameters.h @@ -28,17 +28,24 @@ /* System Clock Frequency */ #define XILINX_CLOCK_FREQ 100000000 +/* Microblaze is microblaze_0 */ +#define XILINX_USE_MSR_INSTR 1 +#define XILINX_PVR 0 +#define XILINX_FSL_NUMBER 0 + /* Interrupt controller is opb_intc_0 */ #define XILINX_INTC_BASEADDR 0x41200000 -#define XILINX_INTC_NUM_INTR_INPUTS 11 +#define XILINX_INTC_NUM_INTR_INPUTS 7 /* Timer pheriphery is opb_timer_1 */ #define XILINX_TIMER_BASEADDR 0x41c00000 -#define XILINX_TIMER_IRQ 1 +#define XILINX_TIMER_IRQ 0 /* Uart pheriphery is RS232_Uart_1 */ -#define XILINX_UART_BASEADDR 0x40600000 -#define XILINX_UART_BAUDRATE 115200 +#define XILINX_UARTLITE_BASEADDR 0x40600000 +#define XILINX_UARTLITE_BAUDRATE 115200 + +/* IIC doesn't exist */ /* GPIO is LEDs_4Bit*/ #define XILINX_GPIO_BASEADDR 0x40000000 @@ -51,14 +58,10 @@ /* Sysace Controller is SysACE_CompactFlash */ #define XILINX_SYSACE_BASEADDR 0x41800000 -#define XILINX_SYSACE_HIGHADDR 0x4180ffff #define XILINX_SYSACE_MEM_WIDTH 16 /* Ethernet controller is Ethernet_MAC */ -#define XPAR_XEMAC_NUM_INSTANCES 1 -#define XPAR_OPB_ETHERNET_0_DEVICE_ID 0 -#define XPAR_OPB_ETHERNET_0_BASEADDR 0x40c00000 -#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x40c0ffff -#define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1 -#define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1 -#define XPAR_OPB_ETHERNET_0_MII_EXIST 1 +#define XILINX_EMAC_BASEADDR 0x40c00000 +#define XILINX_EMAC_DMA_PRESENT 3 +#define XILINX_EMAC_HALF_DUPLEX_EXIST 1 +#define XILINX_EMAC_MII_EXIST 1 diff --git a/include/configs/xupv2p.h b/include/configs/xupv2p.h index 35001d7..006a132 100644 --- a/include/configs/xupv2p.h +++ b/include/configs/xupv2p.h @@ -31,13 +31,34 @@ #define CONFIG_XUPV2P 1 /* uart */ -#define CONFIG_SERIAL_BASE XILINX_UART_BASEADDR -#define CONFIG_BAUDRATE XILINX_UART_BAUDRATE +#ifdef XILINX_UARTLITE_BASEADDR +#define XILINX_UARTLITE +#define CONFIG_SERIAL_BASE XILINX_UARTLITE_BASEADDR +#define CONFIG_BAUDRATE XILINX_UARTLITE_BAUDRATE #define CFG_BAUDRATE_TABLE { CONFIG_BAUDRATE } +#else +#ifdef XILINX_UART16550_BASEADDR +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 4 +#define CONFIG_CONS_INDEX 1 +#define CFG_NS16550_COM1 XILINX_UART16550_BASEADDR +#define CFG_NS16550_CLK XILINX_UART16550_CLOCK_HZ + +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600, 115200 } +#endif +#endif /* ethernet */ -#define CONFIG_EMAC 1 -#define XPAR_EMAC_0_DEVICE_ID XPAR_XEMAC_NUM_INSTANCES +#ifdef XILINX_EMAC_BASEADDR +#define XILINX_EMAC 1 +#else +#ifdef XILINX_EMACLITE_BASEADDR +#define XILINX_EMACLITE 1 +#endif +#endif +#undef ET_DEBUG /* * setting reset address @@ -48,11 +69,13 @@ * U-BOOT auto-relocate to TEXT_BASE. After RESET command Microblaze * jump to CFG_RESET_ADDRESS where is the original U-BOOT code. */ -#define CFG_RESET_ADDRESS 0x36000000 +/* #define CFG_RESET_ADDRESS 0x36000000 */ /* gpio */ +#ifdef XILINX_GPIO_BASEADDR #define CFG_GPIO_0 1 #define CFG_GPIO_0_ADDR XILINX_GPIO_BASEADDR +#endif /* interrupt controller */ #define CFG_INTC_0 1 @@ -119,7 +142,6 @@ #define CFG_ENV_SIZE 0x1000 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SIZE) - /* * BOOTP options */ @@ -128,29 +150,24 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ #include <config_cmd_default.h> -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_BDI -#define CONFIG_CMD_NET -#define CONFIG_CMD_IMI -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_RUN -#define CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS + #define CONFIG_CMD_ASKENV -#define CONFIG_CMD_LOADS -#define CONFIG_CMD_LOADB -#define CONFIG_CMD_MISC -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MFSL #define CONFIG_CMD_PING +#ifdef XILINX_SYSACE_BASEADDR +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#endif /* Miscellaneous configurable options */ #define CFG_PROMPT "U-Boot-mONStR> " @@ -162,7 +179,7 @@ #define CONFIG_BOOTDELAY 30 #define CONFIG_BOOTARGS "root=romfs" -#define CONFIG_HOSTNAME "ml401" +#define CONFIG_HOSTNAME "xupv2p" #define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm" #define CONFIG_IPADDR 192.168.0.3 #define CONFIG_SERVERIP 192.168.0.5 @@ -178,11 +195,13 @@ "echo" /* system ace */ +#ifdef XILINX_SYSACE_BASEADDR #define CONFIG_SYSTEMACE /* #define DEBUG_SYSTEMACE */ #define SYSTEMACE_CONFIG_FPGA #define CFG_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR #define CFG_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH #define CONFIG_DOS_PARTITION +#endif #endif /* __CONFIG_H */

2 2