September 2007 - U-Boot

[U-Boot-Users] 1.3.0-rc1 rootpath not set
by Marc Leeman 19 Sep '07

19 Sep '07

Below you'll see the verbatim output of the serial line; but the setup basically is this: The config file of the board defines a bad default value for rootpath and bootfile; these values should be retrieved from the dhcp reply. In the 1.2.0 bootloader, this is done correctly, in the 1.3.0-rc1; the bootfile is set correctly, but the rootpath fails. This is the output of 1.2.0 U-Boot 1.2.0 (Sep 18 2007 - 13:57:03) MPC83XX Clock configuration: Coherent System Bus: 266 MHz Core: 399 MHz Local Bus Controller: 266 MHz Local Bus: 33 MHz DDR: 266 MHz SEC: 88 MHz I2C1: 88 MHz I2C2: 266 MHz TSEC1: 88 MHz TSEC2: 88 MHz USB MPH: 88 MHz USB DR: 88 MHz CPU: MPC8347E, Rev: 11 at 399.999 MHz Board: Barco BARCO8347NGS103 Platform I2C: ready DRAM: Initializing SDRAM on Local Bus is NOT available! DDR RAM: 64 MB FLASH: 16 MB PCI1: 32-bit on PMC1 PCI2: 32-bit on PMC2, PMC3 PCI: Bus Dev VenId DevId Class Int 00 13 1172 0005 ff00 00 In: serial Out: serial Err: serial Net: TSEC0, TSEC1 Type run net_nfs to get kernel via tftpboot and mount root filesystem over NFS use dhcp_nfs to get an IP and boot over NFS Hit any key to stop autoboot: 0 => printenv bootfile bootfile=_bad_non_dhcp_default_value_bootfile_ => printenv rootpath rootpath=_bad_non_dhcp_default_value_rootpath_ => dhcp Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 10.2.4.41 Using TSEC0 device TFTP from server 10.0.0.6; our IP address is 10.2.4.41 Filename '/home/services/tftpboot/kernels/mleeman/targets/ngs103/nightly/kernel.ngs103.2.6.continuous.img'. Load address: 0x200000 Loading: ################################################################# ################################################################# ################################################################# # done Bytes transferred = 1002956 (f4dcc hex) => printenv bootfile bootfile=/home/services/tftpboot/kernels/mleeman/targets/ngs103/nightly/kernel.ngs103.2.6.continuous.img => printenv rootpath rootpath=/home/firmware/mleeman/targets/ngs103/nightly This is the output for the 1.3.0-rc1 (the version tag is still wrong). U-Boot 1.2.0 (Sep 18 2007 - 13:21:35) MPC83XX Reset Status: Software Hard, External/Internal Soft, External/Internal Hard CPU: e300c1, MPC8347E, Rev: 11 at 399.999 MHz, CSB: 266 MHz Board: Barco BARCO8347NGS103 Platform I2C: ready DRAM: 64 MB FLASH: 16 MB PCI1: 32-bit on PMC1 PCI2: 32-bit on PMC2, PMC3 PCI: Bus Dev VenId DevId Class Int 00 13 1172 0005 ff00 00 In: serial Out: serial Err: serial Net: TSEC0, TSEC1 Type run net_nfs to get kernel via tftpboot and mount root filesystem over NFS use dhcp_nfs to get an IP and boot over NFS Hit any key to stop autoboot: 0 => print bootfile bootfile=_bad_non_dhcp_default_value_bootfile_ => print rootpath rootpath=_bad_non_dhcp_default_value_rootpath_ => dhcp Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 10.2.4.41 Using TSEC0 device TFTP from server 10.0.0.6; our IP address is 10.2.4.41 Filename '/home/services/tftpboot/kernels/mleeman/targets/ngs103/nightly/kernel.ngs103.2.6.continuous.img'. Load address: 0x200000 Loading: ################################################################# #### done Bytes transferred = 1002956 (f4dcc hex) => print bootfile bootfile=/home/services/tftpboot/kernels/mleeman/targets/ngs103/nightly/kernel.ngs103.2.6.continuous.img => print rootpath rootpath=_bad_non_dhcp_default_value_rootpath_ -- greetz, marc Cross my heart, smack me dead...stick a lobster on my head. Crichton - Thanks for Sharing chiana 2.6.18-4-ixp4xx #1 Sun Apr 22 08:34:11 UTC 2007 GNU/Linux

1 1

[U-Boot-Users] Setting entry point in u-boot standalone apps
by David Hearn 19 Sep '07

19 Sep '07

I have a U-boot standalone app which runs on the Gumstix boards. It's based on the /u-boot-1.2.0/examples/ folder. The problem I have is that my entry function - lets call it app_entry() - isn't at the load address, it's somewhere in the middle. I'm using the output from objdump -d <elf file> > <elf file>.dis to determine where in the address range the functions are located. When I originally built the hello_world.c examples, the hello_world() function was located at the load address and everything worked fine. I would do issue the following commands to run it: loadb a0000000 <send the .bin file> go a0000000 However I discovered that as I made changes to this file the hello_world() function was moved around within the address range (ie. it was no longer at the start of the range) - this was discovered when the app no longer worked. After investigating I found that I needed to disassemble the file, locate where the entry function is now located, and do the following commands: loadb a0000000 <send the .bin file> go a0000948 (or whatever the address of my entry function was) This then worked every time. My problem is that I wish to avoid this as every time I change any of the functions located before my entry function, this address changes. It would be far nicer, and easier, to just have my entry function always located at the start of the range and I can then always execute my app by doing 'go a0000000' irrespective of any changes I make to the code.. I'm using a slightly modified version of the Makefile in the examples folder, the particular interesting part (I think) which I've not changed is: $(ELF): $(obj)%: $(obj)%.o $(LIB) $(LD) -g $(EX_LDFLAGS) -Ttext $(LOAD_ADDR) \ -o $@ -e $(notdir $(<:.o=)) $< $(LIB) \ -L$(gcclibdir) -lgcc The -e part should be specifying the entry point of the ELF file, however outputting the result of the $(notdir) part shows it's empty. When I've replaced it with just the entry function's name, it makes no difference either. As I understand it (taken from: <http://sourceware.org/binutils/docs-2.17/ld/Entry-Point.html>): "There are several ways to set the entry point. The linker will set the entry point by trying each of the following methods in order, and stopping when one of them succeeds: * the `-e' entry command-line option; * the |ENTRY(|symbol|)| command in a linker script; * the value of the symbol |start|, if defined; * the address of the first byte of the `.text' section, if present; * The address |0|." Unfortunately, the examples don't use linker scripts, and I don't want to start messing with these as it interacts with u-boot to some extent (certainly built within u-boot's makefile), and it's all working as it is. From what I understand though, the -e option should be sufficient. Has anyone else experienced this problem, and can give any advice as to how to solve it? Thanks David

3 4

[U-Boot-Users] [PATCH] OneNAND Initial Program Loader (IPL) support
by Kyungmin Park 19 Sep '07

19 Sep '07

Hi, This patch enables the OneNAND boot within U-Boot. Before this work, we used another OneNAND IPL called X-Loader based on open source. With this work, we can build the oneboot.bin image without other program. The build sequence is simple. First, it compiles the u-boot.bin Second, it compiles OneNAND IPL Finally, it becomes the oneboot.bin from OneNAND IPL and u-boot.bin The mechanism is similar with NAND boot except it boots from itself. Another thing is that you can only use the OneNAND IPL only to work other bootloader such as RedBoot and so on. Any comments are welcome. Thank you, Kyungmin Park Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> --- diff --git a/Makefile b/Makefile index d680ad0..de8c0ea 100644 --- a/Makefile +++ b/Makefile @@ -251,13 +251,18 @@ NAND_SPL = nand_spl U_BOOT_NAND = $(obj)u-boot-nand.bin endif +ifeq ($(CONFIG_ONENAND_U_BOOT),y) +ONENAND_IPL = onenand_ipl +U_BOOT_ONENAND = $(obj)u-boot-onenand.bin +endif + __OBJS := $(subst $(obj),,$(OBJS)) __LIBS := $(subst $(obj),,$(LIBS)) ######################################################################### ######################################################################### -ALL += $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map $(U_BOOT_NAND) +ALL += $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map $(U_BOOT_NAND) $(U_BOOT_ONENAND) all: $(ALL) @@ -304,6 +309,12 @@ $(NAND_SPL): version $(U_BOOT_NAND): $(NAND_SPL) $(obj)u-boot.bin cat $(obj)nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin +$(ONENAND_IPL): version + $(MAKE) -C onenand_ipl/board/$(BOARDDIR) all + +$(U_BOOT_ONENAND): $(ONENAND_IPL) $(obj)u-boot.bin + cat $(obj)onenand_ipl/onenand-ipl-2k.bin $(obj)u-boot.bin > $(obj)oneboot.bin + version: @echo -n "#define U_BOOT_VERSION \"U-Boot " > $(VERSION_FILE); \ echo -n "$(U_BOOT_VERSION)" >> $(VERSION_FILE); \ @@ -2361,6 +2372,7 @@ omap2420h4_config : unconfig apollon_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 apollon + @echo "CONFIG_ONENAND_U_BOOT = y" >> $(obj)include/config.mk #======================================================================== # i386 @@ -2621,6 +2633,7 @@ clean: rm -f $(obj)board/bf537-stamp/u-boot.lds $(obj)board/bf561-ezkit/u-boot.lds rm -f $(obj)include/bmp_logo.h rm -f $(obj)nand_spl/u-boot-spl $(obj)nand_spl/u-boot-spl.map + rm -f $(obj)onenand_ipl/onenand-ipl $(obj)onenand_ipl/onenand-ipl.map clobber: clean find $(OBJTREE) -type f \( -name .depend \ @@ -2634,6 +2647,7 @@ clobber: clean rm -f $(obj)tools/inca-swap-bytes $(obj)cpu/mpc824x/bedbug_603e.c rm -f $(obj)include/asm/proc $(obj)include/asm/arch $(obj)include/asm [ ! -d $(OBJTREE)/nand_spl ] || find $(obj)nand_spl -lname "*" -print | xargs rm -f + [ ! -d $(OBJTREE)/onenand_ipl ] || find $(obj)onenand_ipl -lname "*" -print | xargs rm -f ifeq ($(OBJTREE),$(SRCTREE)) mrproper \ diff --git a/board/apollon/apollon.c b/board/apollon/apollon.c index 064d143..383b064 100644 --- a/board/apollon/apollon.c +++ b/board/apollon/apollon.c @@ -440,7 +440,8 @@ void muxSetupTouchScreen(void) void muxSetupGPMC(void) { /* gpmc_io_dir, MCR */ - writel(0x4800008C, 0x19000000); + volatile unsigned int *MCR = (unsigned int *) 0x4800008C; + *MCR = 0x19000000; /* NOR FLASH CS0 */ /* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode 0; Byte-3 */ diff --git a/cpu/arm1136/start.S b/cpu/arm1136/start.S index 17c7a83..b272d2f 100644 --- a/cpu/arm1136/start.S +++ b/cpu/arm1136/start.S @@ -35,6 +35,25 @@ #endif .globl _start _start: b reset +#ifdef CONFIG_ONENAND_IPL + ldr pc, _hang + ldr pc, _hang + ldr pc, _hang + ldr pc, _hang + ldr pc, _hang + ldr pc, _hang + ldr pc, _hang + +_hang: + .word do_hang + .word 0x12345678 + .word 0x12345678 + .word 0x12345678 + .word 0x12345678 + .word 0x12345678 + .word 0x12345678 + .word 0x12345678 /* now 16*4=64 */ +#else ldr pc, _undefined_instruction ldr pc, _software_interrupt ldr pc, _prefetch_abort @@ -51,6 +70,7 @@ _not_used: .word not_used _irq: .word irq _fiq: .word fiq _pad: .word 0x12345678 /* now 16*4=64 */ +#endif /* CONFIG_ONENAND_IPL */ .global _end_vect _end_vect: @@ -139,7 +159,10 @@ relocate: /* relocate U-Boot to RAM */ adr r0, _start /* r0 <- current position of code */ ldr r1, _TEXT_BASE /* test if we run from flash or RAM */ cmp r0, r1 /* don't reloc during debug */ +#ifndef CONFIG_ONENAND_IPL beq stack_setup +#endif /* CONFIG_ONENAND_IPL */ + ldr r2, _armboot_start ldr r3, _bss_start @@ -156,26 +179,36 @@ copy_loop: /* Set up the stack */ stack_setup: ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */ +#ifdef CONFIG_ONENAND_IPL + sub sp, r0, #128 /* leave 32 words for abort-stack */ +#else sub r0, r0, #CFG_MALLOC_LEN /* malloc area */ sub r0, r0, #CFG_GBL_DATA_SIZE /* bdinfo */ #ifdef CONFIG_USE_IRQ sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ) #endif sub sp, r0, #12 /* leave 3 words for abort-stack */ +#endif /* CONFIG_ONENAND_IPL */ clear_bss: ldr r0, _bss_start /* find start of bss segment */ ldr r1, _bss_end /* stop here */ mov r2, #0x00000000 /* clear */ +#ifndef CONFIG_ONENAND_IPL clbss_l:str r2, [r0] /* clear loop... */ add r0, r0, #4 cmp r0, r1 bne clbss_l +#endif ldr pc, _start_armboot +#ifdef CONFIG_ONENAND_IPL +_start_armboot: .word start_oneboot +#else _start_armboot: .word start_armboot +#endif /* @@ -214,6 +247,8 @@ cpu_init_crit: bl lowlevel_init /* go setup pll,mux,memory */ mov lr, ip /* restore link */ mov pc, lr /* back to my caller */ + +#ifndef CONFIG_ONENAND_IPL /* ************************************************************************* * @@ -326,10 +361,17 @@ cpu_init_crit: .macro get_fiq_stack @ setup FIQ stack ldr sp, FIQ_STACK_START .endm +#endif /* CONFIG_ONENAND_IPL */ /* * exception handlers */ +#ifdef CONFIG_ONENAND_IPL + .align 5 +do_hang: + ldr sp, _TEXT_BASE /* use 32 words about stack */ + bl hang /* hang and never return */ +#else .align 5 undefined_instruction: get_bad_stack @@ -415,3 +457,4 @@ rstctl: .word PM_RSTCTRL_WKUP #endif +#endif /* CONFIG_ONENAND_IPL */ diff --git a/include/configs/apollon.h b/include/configs/apollon.h index 49fd234..d6ecc72 100644 --- a/include/configs/apollon.h +++ b/include/configs/apollon.h @@ -35,6 +35,7 @@ #define CONFIG_OMAP2420 1 /* which is in a 2420 */ #define CONFIG_OMAP2420_APOLLON 1 #define CONFIG_APOLLON 1 + #define CONFIG_APOLLON_PLUS 1 /* If you have apollon plus 1.x */ /* Clock config to target*/ diff --git a/onenand_ipl/board/apollon/Makefile b/onenand_ipl/board/apollon/Makefile new file mode 100644 index 0000000..f6cdae1 --- /dev/null +++ b/onenand_ipl/board/apollon/Makefile @@ -0,0 +1,67 @@ + +include $(TOPDIR)/config.mk +include $(TOPDIR)/include/config.mk +include $(TOPDIR)/onenand_ipl/board/$(BOARDDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/onenand_ipl/board/$(BOARDDIR)/u-boot.onenand.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_ONENAND_IPL +CFLAGS += -DCONFIG_ONENAND_IPL +OBJCLFAGS += --gap-fill=0x00 + +SOBJS = start.o low_levelinit.o _memcpy32.o +COBJS = apollon.o onenand_read.o onenand_boot.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/onenand_ipl/board/$(BOARDDIR) + +onenandobj := $(OBJTREE)/onenand_ipl/ + +ALL = $(onenandobj)onenand-ipl $(onenandobj)onenand-ipl.bin $(onenandobj)onenand-ipl-2k.bin + +all: $(obj).depend $(ALL) + +$(onenandobj)onenand-ipl-2k.bin: $(onenandobj)onenand-ipl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=0x800 -O binary $< $@ + ls -al $(onenandobj) + +$(onenandobj)onenand-ipl.bin: $(onenandobj)onenand-ipl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(onenandobj)onenand-ipl: $(OBJS) + echo abc + cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \ + -Map $(onenandobj)onenand-ipl.map \ + -o $(onenandobj)onenand-ipl + +# create symbolic links from common files + +# from cpu directory +$(obj)start.S: + rm -f $(obj)start.S + ln -s $(SRCTREE)/cpu/$(CPU)/start.S $(obj)start.S + +# from onenand_ipl directory +$(obj)onenand_ipl.h: + rm -f $(obj)onenand_ipl.h + ln -s $(SRCTREE)/onenand_ipl/onenand_ipl.h $(obj)onenand_ipl.h + +$(obj)onenand_boot.c: $(obj)onenand_ipl.h + rm -f $(obj)onenand_boot.c + ln -s $(SRCTREE)/onenand_ipl/onenand_boot.c $(obj)onenand_boot.c + +$(obj)onenand_read.c: $(obj)onenand_ipl.h + rm -f $(obj)onenand_read.c + ln -s $(SRCTREE)/onenand_ipl/onenand_read.c $(obj)onenand_read.c + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)$.c + $(CC) $(CFLAGS) -c -o $@ $< + +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend diff --git a/onenand_ipl/board/apollon/apollon.c b/onenand_ipl/board/apollon/apollon.c new file mode 100644 index 0000000..61a8428 --- /dev/null +++ b/onenand_ipl/board/apollon/apollon.c @@ -0,0 +1,71 @@ +/* + * (C) Copyright 2005 + * Samsung Electronics + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <asm/arch/mux.h> + +#define write_config_reg(reg, value) \ +do { \ + writeb(value, reg); \ +} while (0) + +/***************************************** + * Routine: board_init + * Description: Early hardware init. + *****************************************/ +int board_init(void) +{ + return 0; +} + +#ifdef CFG_PRINTF +/* Pin Muxing registers used for UART1 */ +/**************************************** + * Routine: muxSetupUART1 (ostboot) + * Description: Set up uart1 muxing + *****************************************/ +static void muxSetupUART1(void) +{ + /* UART1_CTS pin configuration, PIN = D21 */ + write_config_reg(CONTROL_PADCONF_UART1_CTS, 0); + /* UART1_RTS pin configuration, PIN = H21 */ + write_config_reg(CONTROL_PADCONF_UART1_RTS, 0); + /* UART1_TX pin configuration, PIN = L20 */ + write_config_reg(CONTROL_PADCONF_UART1_TX, 0); + /* UART1_RX pin configuration, PIN = T21 */ + write_config_reg(CONTROL_PADCONF_UART1_RX, 0); +} +#endif + +/********************************************************** + * Routine: s_init + * Description: Does early system init of muxing and clocks. + * - Called at time when only stack is available. + **********************************************************/ +int s_init(int skip) +{ +#ifdef CFG_PRINTF + muxSetupUART1(); +#endif + return 0; +} diff --git a/onenand_ipl/board/apollon/config.mk b/onenand_ipl/board/apollon/config.mk new file mode 100644 index 0000000..12873a0 --- /dev/null +++ b/onenand_ipl/board/apollon/config.mk @@ -0,0 +1,14 @@ +# +# (C) Copyright 2005-2007 Samsung Elcronics +# Kyungmin Park <kyungmin.park(a)samsung.com> +# +# Samsung Apollon board with OMAP2420 (ARM1136) cpu +# +# Apollon has 1 bank of 128MB mDDR-SDRAM on CS0 +# Physical Address: +# 8000'0000 (bank0) +# 8800'0000 (bank1) +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) + +TEXT_BASE = 0x00000000 diff --git a/onenand_ipl/board/apollon/low_levelinit.S b/onenand_ipl/board/apollon/low_levelinit.S new file mode 100644 index 0000000..0ffa36f --- /dev/null +++ b/onenand_ipl/board/apollon/low_levelinit.S @@ -0,0 +1,205 @@ +/* + * Board specific setup info + * + * (C) Copyright 2005-2007 Samsung Electronics + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Derived from board/omap2420h4/platform.S + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <asm/arch/omap2420.h> +#include <asm/arch/mem.h> +#include <asm/arch/clocks.h> + +#define APOLLON_CS0_BASE 0x00000000 + +#ifdef PRCM_CONFIG_I +#define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 +#define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 +#define SDRC_RFR_CTRL_0_VAL 0x00044C01 + +/* GPMC */ +#define APOLLON_GPMC_CONFIG1_0 0xe30d1201 +#define APOLLON_GPMC_CONFIG2_0 0x000c1000 +#define APOLLON_GPMC_CONFIG3_0 0x00030400 +#define APOLLON_GPMC_CONFIG4_0 0x0B841006 +#define APOLLON_GPMC_CONFIG5_0 0x020F0C11 +#define APOLLON_GPMC_CONFIG6_0 0x00000000 +#define APOLLON_GPMC_CONFIG7_0 (0x00000e40 | (APOLLON_CS0_BASE >> 24)) + +#elif defined(PRCM_CONFIG_II) +#define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 +#define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C +#define SDRC_RFR_CTRL_0_VAL 0x00030001 + +/* GPMC */ +#define APOLLON_GPMC_CONFIG1_0 0xe30d1201 +#define APOLLON_GPMC_CONFIG2_0 0x00080E81 +#define APOLLON_GPMC_CONFIG3_0 0x00030400 +#define APOLLON_GPMC_CONFIG4_0 0x08041586 +#define APOLLON_GPMC_CONFIG5_0 0x020C090E +#define APOLLON_GPMC_CONFIG6_0 0x00000000 +#define APOLLON_GPMC_CONFIG7_0 (0x00000e40 | (APOLLON_CS0_BASE >> 24)) + +#else +#error "Please configure PRCM schecm" +#endif + +_TEXT_BASE: + .word TEXT_BASE /* sdram load addr from config.mk */ + +.globl lowlevel_init +lowlevel_init: + mov r3, r0 /* save skip information */ + + /* Disable watchdog */ + ldr r0, =WD2_BASE + ldr r1, =WD_UNLOCK1 + str r1, [r0, #WSPR] + + ldr r1, =WD_UNLOCK2 + str r1, [r0, #WSPR] + +#ifdef DEBUG_LED + /* LED0 OFF */ + ldr r0, =0x480000E5 /* ball AA10, mode 3 */ + mov r1, #0x0b + strb r1, [r0] +#endif + + /* Pin muxing for SDRC */ + mov r1, #0x00 + ldr r0, =0x480000A1 /* ball C12, mode 0 */ + strb r1, [r0] + + ldr r0, =0x48000032 /* ball D11, mode 0 */ + strb r1, [r0] + + ldr r0, =0x480000A3 /* ball B13, mode 0 */ + strb r1, [r0] + + /* SDRC setting */ + ldr r0, =OMAP2420_SDRC_BASE + ldr r1, =0x00000010 + str r1, [r0, #0x10] + + ldr r1, =0x00000100 + str r1, [r0, #0x44] + + /* SDRC CS0 configuration */ +#ifdef CONFIG_APOLLON_PLUS + ldr r1, =0x01702011 +#else + ldr r1, =0x00d04011 +#endif + str r1, [r0, #0x80] + + ldr r1, =SDRC_ACTIM_CTRLA_0_VAL + str r1, [r0, #0x9C] + + ldr r1, =SDRC_ACTIM_CTRLB_0_VAL + str r1, [r0, #0xA0] + + ldr r1, =SDRC_RFR_CTRL_0_VAL + str r1, [r0, #0xA4] + + ldr r1, =0x00000041 + str r1, [r0, #0x70] + + /* Manual command sequence */ + ldr r1, =0x00000007 + str r1, [r0, #0xA8] + + ldr r1, =0x00000000 + str r1, [r0, #0xA8] + + ldr r1, =0x00000001 + str r1, [r0, #0xA8] + + ldr r1, =0x00000002 + str r1, [r0, #0xA8] + str r1, [r0, #0xA8] + + /* + * CS0 SDRC Mode register + * Burst length = 4 - DDR memory + * Serial mode + * CAS latency = 3 + */ + ldr r1, =0x00000032 + str r1, [r0, #0x84] + + /* Note: You MUST set EMR values */ + /* EMR1 & EMR2 */ + ldr r1, =0x00000000 + str r1, [r0, #0x88] + str r1, [r0, #0x8C] + +#ifdef OLD_SDRC_DLLA_CTRL + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00007306 + str r1, [r0, #0x60] + + ldr r1, =0x00007303 + str r1, [r0, #0x60] +#else + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x60] + + ldr r1, =0x00000503 + str r1, [r0, #0x60] +#endif + +#ifdef __BROKEN_FEATURE__ + /* SDRC_DLLB_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x68] + + ldr r1, =0x00000503 + str r1, [r0, #0x68] +#endif + + /* little delay after init */ + mov r2, #0x1800 +1: + subs r2, r2, #0x1 + bne 1b + + ldr sp, SRAM_STACK + str ip, [sp] /* stash old link register */ + mov ip, lr /* save link reg across call */ + mov r0, r3 /* pass skip info to s_init */ + + bl s_init /* go setup pll,mux,memory */ + + ldr ip, [sp] /* restore save ip */ + mov lr, ip /* restore link reg */ + + /* back to arch calling code */ + mov pc, lr + + /* the literal pools origin */ + .ltorg + +SRAM_STACK: + .word LOW_LEVEL_SRAM_STACK diff --git a/onenand_ipl/board/apollon/u-boot.onenand.lds b/onenand_ipl/board/apollon/u-boot.onenand.lds new file mode 100644 index 0000000..3d18fad --- /dev/null +++ b/onenand_ipl/board/apollon/u-boot.onenand.lds @@ -0,0 +1,53 @@ +/* + * (C) Copyright 2005-2007 Samsung Electronics + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Derived from X-loader + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/onenand_ipl/onenand_boot.c b/onenand_ipl/onenand_boot.c new file mode 100644 index 0000000..c0005f7 --- /dev/null +++ b/onenand_ipl/onenand_boot.c @@ -0,0 +1,81 @@ +/* + * (C) Copyright 2007 Samsung Electronics + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Derived from x-loader + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <version.h> + +#include "onenand_ipl.h" + +#ifdef CFG_PRINTF +int print_info(void) +{ + printf(XLOADER_VERSION); + + return 0; +} +#endif + +typedef int (init_fnc_t)(void); + +init_fnc_t *init_sequence[] = { + board_init, /* basic board dependent setup */ +#ifdef CFG_PRINTF + serial_init, /* serial communications setup */ + print_info, +#endif + NULL, +}; + +void start_oneboot(void) +{ + init_fnc_t **init_fnc_ptr; + uchar *buf; + + for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) { + if ((*init_fnc_ptr)() != 0) + hang(); + } + + buf = (uchar *) CFG_LOAD_ADDR; + + if (!onenand_read_block(buf, ONENAND_START_BLOCK)) + buf += ONENAND_BLOCK_SIZE; + + if (buf == (uchar *)CFG_LOAD_ADDR) + hang(); + + /* go run U-Boot and never return */ + printf("Starting OS Bootloader...\n"); + ((init_fnc_t *)CFG_LOAD_ADDR)(); + + /* should never come here */ +} + +void hang(void) +{ + /* if board_hang() returns, hange here */ + printf("X-Loader hangs\n"); + for (;;); +} diff --git a/onenand_ipl/onenand_ipl.h b/onenand_ipl/onenand_ipl.h new file mode 100644 index 0000000..ec8ca3a --- /dev/null +++ b/onenand_ipl/onenand_ipl.h @@ -0,0 +1,44 @@ +/* + * (C) Copyright 2007 Samsung Electronics + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _ONENAND_IPL_H +#define _ONENAND_IPL_H + +#include <linux/mtd/onenand_regs.h> + +#define ONENAND_START_BLOCK 0 +#define ONENAND_BLOCK_SIZE 2048 + +#ifndef CFG_PRINTF +#define printf(format, args...) +#endif + +#define onenand_readw(a) readw(a) +#define onenand_writew(v, a) writew(v, a) + +#define THIS_ONENAND(a) (CFG_ONENAND_BASE + (a)) + +#define READ_INTERRUPT() \ + onenand_readw(THIS_ONENAND(ONENAND_REG_INTERRUPT)) + +#define ONENAND_PAGE_SIZE 2048 + +extern int onenand_read_block(unsigned char *buf, ulong block); +#endif diff --git a/onenand_ipl/onenand_read.c b/onenand_ipl/onenand_read.c new file mode 100644 index 0000000..f81f4df --- /dev/null +++ b/onenand_ipl/onenand_read.c @@ -0,0 +1,105 @@ +/* + * (C) Copyright 2005 Samsung Electronis + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +#include <asm/io.h> +#include <asm/string.h> + +#include "onenand_ipl.h" + +#define onenand_block_address(block) (block) +#define onenand_sector_address(page) (page << 2) +#define onenand_buffer_address() ((1 << 3) << 8) +#define onenand_bufferram_address(block) (0) + +/* read a page with ECC */ +static inline int onenand_read_page(ulong block, ulong page, u_char *buf) +{ + unsigned long *base; + +#ifndef __HAVE_ARCH_MEMCPY32 + unsigned int offset, value; + unsigned long *p; +#endif + + onenand_writew(onenand_block_address(block), + THIS_ONENAND(ONENAND_REG_START_ADDRESS1)); + + onenand_writew(onenand_sector_address(page), + THIS_ONENAND(ONENAND_REG_START_ADDRESS8)); + + onenand_writew(onenand_buffer_address(), + THIS_ONENAND(ONENAND_REG_START_BUFFER)); + + onenand_writew(onenand_bufferram_address(block), + THIS_ONENAND(ONENAND_REG_START_ADDRESS2)); + + onenand_writew(ONENAND_INT_CLEAR, THIS_ONENAND(ONENAND_REG_INTERRUPT)); + + onenand_writew(ONENAND_CMD_READ, THIS_ONENAND(ONENAND_REG_COMMAND)); + +#ifndef __HAVE_ARCH_MEMCPY32 + p = (unsigned long *) buf; +#endif + base = (unsigned long *) (CFG_ONENAND_BASE + ONENAND_DATARAM); + + while (!(READ_INTERRUPT() & ONENAND_INT_READ)) + continue; + +#ifdef __HAVE_ARCH_MEMCPY32 + /* 32 bytes boundary memory copy */ + memcpy32(buf, base, ONENAND_PAGE_SIZE); +#else + for (offset = 0; offset < (ONENAND_PAGE_SIZE >> 2); offset++) { + value = *(base + offset); + *p++ = value; + } +#endif + + return 0; +} + +#define ONENAND_START_PAGE 1 +#define ONENAND_PAGES_PER_BLOCK 64 + +/** + * onenand_read_block - Read a block data to buf + * @return 0 on success + */ +int onenand_read_block(unsigned char *buf, ulong block) +{ + int page, offset = 0; + + /* NOTE: you must read page from page 1 of block 0 */ + /* read the block page by page*/ + for (page = ONENAND_START_PAGE; + page < ONENAND_PAGES_PER_BLOCK; page++) { + + onenand_read_page(block, page, buf + offset); + + offset += ONENAND_PAGE_SIZE; + } + + return 0; +}

1 0

[U-Boot-Users] NAND and bad blocks
by MatthewLCreech＠eaton.com 19 Sep '07

19 Sep '07

Hi, I'm trying to figure out what my options are for booting a system completely from NAND flash. Googling around hasn't yielded much info, but browsing "drivers/nand/" I've gathered that U-Boot handles bad blocks (factory or worn-out) & bit-flips to some degree. It's not entirely clear how things work by glancing at the code, though, so I have a few questions: 1. How does U-Boot handle a bad block in the area where the environment is stored? I can create a second environment via CFG_ENV_OFFSET_REDUND, but that's not very flexible (what if the primary and the backup are both bad blocks?) I also need to write to the environment from within Linux via the "fw_setenv" utility, but it doesn't seem to have any NAND awareness. 2. It's not obvious to me how U-Boot reacts when it encounters a bad block. If I'm copying a kernel image out of NAND, and a bad block is encountered, does it skip to the next block? If so, do I need to compensate by padding each partition with unused blocks, or how else does addressing work? Similarly for writes - if I do "nand write <memaddr> <location> 100000", and the first block is bad, will U-Boot write all 0x100000 bytes _after_ that block? 3. Can Linux handle bad blocks in the same manner? Specifically, I need to use 'nandwrite' to copy a kernel image to an MTD partition from within Linux, and have U-Boot read the image correctly on bootup, both in the presence of bad blocks and bit-flips. The only references I found were at the openmoko site, but I'm not sure how much of what they discuss is native in U-Boot & Linux, vs. being added on for openmoko. Thanks in advance for the help! -- Matthew L. Creech

3 3

[U-Boot-Users] Uboot Splash Screen
by Roger Williamson 18 Sep '07

18 Sep '07

Fellow U-booters, I've run into an issue with my uboot, I want to display a bitmap image when the system boots; however, all the screen does at startup is fade from white to black and back until the OS boots up. I'm currently using an LCD screen with a resolution of 640x480 (landscape) in 8 bit mode, and I have a bitmap with the same dimentions 640*480*8 loaded into the memory at the microcontroller's recommended memory address, and I have the bitmap image converted into a header file and used as the bmp_logo.h file. Unfortunately, the modifications I've made don't seems to change the fact that the screen just fades from white to black and back, or really how fast the screen does so--the image I'm using is mostly white with some red text. Thank you, Roger Williamson Orbital TMS -- Colombia CE Software Engineer (443) 259-7320 ----------------------------------------- Notice: This e-mail is intended solely for use of the individual or entity to which it is addressed and may contain information that is proprietary, privileged and exempt from disclosure under applicable law. If the reader is not the intended recipient or agent responsible for delivering the message to the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. This communication may also contain data subject to U.S. export laws. If so, that data subject to the International Traffic in Arms Regulation cannot be disseminated, distributed or copied to foreign nationals, residing in the U.S. or abroad, absent the express prior approval of the U.S. Department of State. If you have received this communication in error, please notify the sender by reply e-mail and destroy the e-mail message and any physical copies made of the communication. Thank you.

2 1

[U-Boot-Users] Configuring Spansion flash
by Yasothabalan Ramaswamy-TLS,Chennai 18 Sep '07

18 Sep '07

Hi all, I am using Lite5200B board with SPANSION type flash. UBoot code doesn't detect this flash. Can anyone please help me what are all the changes to be made to configure SPANSION type flash. SPANSION 64MB flash. Regards, Yasotha Balan R DISCLAIMER: ----------------------------------------------------------------------------------------------------------------------- The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only. It shall not attach any liability on the originator or HCL or its affiliates. Any views or opinions presented in this email are solely those of the author and may not necessarily reflect the opinions of HCL or its affiliates. Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have received this email in error please delete it and notify the sender immediately. Before opening any mail and attachments please check them for viruses and defect. -----------------------------------------------------------------------------------------------------------------------

4 11

Re: [U-Boot-Users] Ethernet port
by Ramasamy C 18 Sep '07

18 Sep '07

> Here in my board I have two Ethernet ports; > So now I have to set two different IP addresses for these ports. > > As when the U-Boot prompt comes up we can set the IP address as, > > => set ipaddr 10.128.19.1 > => set ethaddr aa:bb:cc:ee:ff:gg > > So above setting is valid only for single Ethernet port. > Yes. > My doubt how to set IP address for another Ethernet port or what is the > method to do that? > Presently U-Boot supports only one active Ethernet configuration at a time. In case if you wish to use multiple ethernet ports with same or different IP/MAC addresses, it is _not_ possible. In case if you wish to test other ethernet ports, this can be done by changing the 'ethact' value. Though this cannot be done simultaneously. Ramasamy C -- "Thought Ought not be Caught or Bought to be Faught till Nought." - Philosophical Nights

2 1

[U-Boot-Users] [PATCH] Bugfix: remove embedded null (\0) from CFG_BOOTFILE macro in TQM8540_config
by Grant Likely 18 Sep '07

18 Sep '07

From: Grant Likely <grant.likely(a)secretlab.ca> /bin/bash and /bin/dash (which /bin/sh is linked to on ubuntu) handle embedded nulls in a string differently. For example, the following statement: echo "this is a string\0" > afile Will produce the following with /bin/bash: "this is a string\0" But with /bin/dash, will produce: "this is a string Bug fixed by moving the embedded null out of the makefile and into the config header. Also renamed the macro to avoid usage colision with the same macro used by other board ports. Signed-off-by: Grant Likely <grant.likely(a)secretlab.ca> --- Jon/Wolfgang, this one should probably go in for 1.3.0 Makefile | 2 +- include/configs/TQM85xx.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/Makefile b/Makefile index 85885b1..a87311c 100644 --- a/Makefile +++ b/Makefile @@ -1961,7 +1961,7 @@ TQM8560_config: unconfig echo "#define CONFIG_TQM$${CTYPE}">>$(obj)include/config.h; \ echo "#define CONFIG_HOSTNAME tqm$${CTYPE}">>$(obj)include/config.h; \ echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>$(obj)include/config.h; \ - echo "#define CFG_BOOTFILE \"bootfile=/tftpboot/tqm$${CTYPE}/uImage\0\"">>$(obj)include/config.h + echo "#define CFG_BOOTFILE_PATH \"/tftpboot/tqm$${CTYPE}/uImage\"">>$(obj)include/config.h @$(MKCONFIG) -a TQM85xx ppc mpc85xx tqm85xx ######################################################################### diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index 2f23c50..6dbd392 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -449,7 +449,7 @@ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ + "bootfile="CFG_BOOTFILE_PATH"\0" \ "netdev=eth0\0" \ "consdev=ttyS0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \

1 0

[U-Boot-Users] [PATCH]: Reset issue fix on mpc85xx
by urwithsughosh＠gmail.com 18 Sep '07

18 Sep '07

Hello, I tried the v1.3.0-rc1 on the ADS board, and problem of the board reset through the 'reset' command pertains. I'm still not sure about the reason of the MSR getting cleared, but am using a brute force approach. Signed-off-by: Sughosh Ganu <urwithsughosh(a)gmail.com> diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 08e0468..bbc5444 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -163,7 +163,12 @@ int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[]) * Initiate hard reset in debug control register DBCR0 * Make sure MSR[DE] = 1 */ - unsigned long val; + unsigned long val, msr; + + msr = mfmsr (); + msr |= MSR_DE; + mtmsr (msr); + val = mfspr(DBCR0); val |= 0x70000000; mtspr(DBCR0,val); -- sughosh

2 2

[U-Boot-Users] [PATCH] fsl_pci_init Fix command register initialization issue.
by Jason Jin 18 Sep '07

18 Sep '07

Use generic setup_device to initialize standard pci regs for the host will lost the initilization for the command register. This patch initilize those regs including command register directly. Signed-off-by: Jason Jin <Jason.jin(a)freescale.com> --- drivers/fsl_pci_init.c | 15 ++++++++------- 1 files changed, 8 insertions(+), 7 deletions(-) diff --git a/drivers/fsl_pci_init.c b/drivers/fsl_pci_init.c index 3a13eea..5335fdb 100644 --- a/drivers/fsl_pci_init.c +++ b/drivers/fsl_pci_init.c @@ -130,13 +130,14 @@ fsl_pci_init(struct pci_controller *hose) } - /* Use generic setup_device to initialize standard pci regs, - * but do not allocate any windows since any BAR found (such - * as PCSRBAR) is not in this cpu's memory space. - */ - - pciauto_setup_device(hose, dev, 0, hose->pci_mem, - hose->pci_prefetch, hose->pci_io); + /* Initialize standard pci regs directly, do not allocate any windows + * since any BAR found (such as PCSRBAR) is not in this cpu's memory space. + */ + pci_hose_read_config_dword(hose, dev, PCI_COMMAND, &temp32); + temp32 |= (PCI_COMMAND_IO | PCI_COMMAND_MEMORY); + pci_hose_write_config_dword(hose, dev, PCI_COMMAND, temp32); + pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08); + pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80); #ifndef CONFIG_PCI_NOSCAN printf (" Scanning PCI bus %02x\n", hose->current_busno); -- 1.5.2

1 0

[U-Boot-Users] U-boot
by Binay Kumar 18 Sep '07

18 Sep '07

Hi All, I want boot my PC i.e pentium 4 with U-Boot.Is it possible if yes how?Can u pls. explanin me in detail. Regards Binay

2 1

[U-Boot-Users] [PATCH 6/6] mpc83xx: update the CREDITS and MAINTAINERS
by Dave Liu 18 Sep '07

18 Sep '07

update the CREDITS and MAINTAINERS. Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- CREDITS | 5 +++++ MAINTAINERS | 1 + 2 files changed, 6 insertions(+), 0 deletions(-) diff --git a/CREDITS b/CREDITS index 0953e7b..b21d60a 100644 --- a/CREDITS +++ b/CREDITS @@ -303,6 +303,11 @@ D: Support for Nios Stratix Development Kit (DK-1S10) D: Support for SSV ADNP/ESC1 (Nios Cyclone) W: http://www.li-pro.net +N: Dave Liu +E: daveliu(a)freescale.com +D: Support for MPC832x, MPC8360, MPC837x +W: www.freescale.com + N: Raymond Lo E: lo(a)routefree.com D: Support for DOS partitions diff --git a/MAINTAINERS b/MAINTAINERS index 850438d..a920e80 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -223,6 +223,7 @@ The LEOX team <team(a)leox.org> Dave Liu <daveliu(a)freescale.com> + MPC832XEMDS MPC832x MPC8360EMDS MPC8360 MPC837XEMDS MPC837x -- 1.5.1

1 0

[U-Boot-Users] [PATCH 5/6] mpc83xx: add MAINTAINER and MAKEALL entries for the mpc837xemds
by Dave Liu 18 Sep '07

18 Sep '07

Add the MAINTAINER and MAKEALL entries for mpc837xemds Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- MAINTAINERS | 1 + MAKEALL | 1 + 2 files changed, 2 insertions(+), 0 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index b8c1fdc..850438d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -224,6 +224,7 @@ The LEOX team <team(a)leox.org> Dave Liu <daveliu(a)freescale.com> MPC8360EMDS MPC8360 + MPC837XEMDS MPC837x Nye Liu <nyet(a)zumanetworks.com> diff --git a/MAKEALL b/MAKEALL index 2597d1f..d2a2ad7 100755 --- a/MAKEALL +++ b/MAKEALL @@ -305,6 +305,7 @@ LIST_83xx=" \ MPC8349ITX \ MPC8349ITXGP \ MPC8360EMDS \ + MPC837XEMDS \ sbc8349 \ TQM834x \ " -- 1.5.1

1 0

[U-Boot-Users] [PATCH 4/6] mpc83xx: Add the MPC837xEMDS board readme
by Dave Liu 18 Sep '07

18 Sep '07

Add the README.mpc837xemds to /doc Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- doc/README.mpc837xemds | 104 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 104 insertions(+), 0 deletions(-) create mode 100644 doc/README.mpc837xemds diff --git a/doc/README.mpc837xemds b/doc/README.mpc837xemds new file mode 100644 index 0000000..3f0cdf7 --- /dev/null +++ b/doc/README.mpc837xemds @@ -0,0 +1,104 @@ +Freescale MPC837xEMDS Board +----------------------------------------- +1. Board Switches and Jumpers +1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC837xEMDS board + For some reason, the HW designers describe the switch settings + in terms of 0 and 1, and then map that to physical switches where + the label "On" refers to logic 0 and "Off" is logic 1. + + Switch bits are numbered 1 through, like, 4 6 8 or 10, but the + bits may contribute to signals that are numbered based at 0, + and some of those signals may be high-bit-number-0 too. Heed + well the names and labels and do not get confused. + + "Off" == 1 + "On" == 0 + + SW4[8] is the bit labled 8 on Switch 4. + SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2. + SW2[1:8]= 0000_0001 refers to bits labeled 1 through 7 is set as "On" + and bits labeled 8 is set as "Off". + +1.1 For the MPC837xEMDS Processor Board + + First, make sure the board default setting is consistent with the + document shipped with your board. Then apply the following setting: + SW3[1-8]= 0011_0000 (BOOTSEQ, ROMLOC setting) + SW4[1-8]= 0000_0110 (core PLL setting) + SW5[1-8]= 1001_1000 (system PLL, boot up from low end of flash) + SW6[1-8]= 0000_1000 (HRCW is read from NOR FLASH) + SW7[1-8]= 0110_1101 (TSEC1/2 interface setting - RGMII) + J3 2-3, TSEC1 LVDD1 with 2.5V + J6 2-3, TSEC2 LVDD2 with 2.5V + J9 2-3, CLKIN from osc on board + J10 removed, CS0 connect to NOR flash; when mounted, CS0 connect to NAND + J11 removed, Hardware Reset Configuration Word load from FLASH(NOR or NAND) + mounted, HRCW load from BCSR. + + on board Oscillator: 66M + +2. Memory Map + +2.1. The memory map should look pretty much like this: + + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M + 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M + 0xc000_0000 0xdfff_ffff Empty 512M + 0xe000_0000 0xe00f_ffff Int Mem Reg Space 1M + 0xe010_0000 0xe02f_ffff Empty 2M + 0xe030_0000 0xe03f_ffff PCI IO 1M + 0xe040_0000 0xe05f_ffff Empty 2M + 0xe060_0000 0xe060_8000 NAND Flash 32K + 0xf400_0000 0xf7ff_ffff Empty 64M + 0xf800_0000 0xf800_7fff BCSR on CS1 32K + 0xfe00_0000 0xffff_ffff NOR Flash on CS0 32M + +3. Definitions + +3.1 Explanation of NEW definitions in: + + include/configs/MPC837XEMDS.h + + CONFIG_MPC83XX MPC83xx family for both MPC837x and MPC8360 + CONFIG_MPC837X MPC837x specific + CONFIG_MPC837XEMDS MPC837XEMDS board specific + +4. Compilation + + Assuming you're using BASH shell: + + export CROSS_COMPILE=your-cross-compile-prefix + cd u-boot + make distclean + make MPC837XEMDS_config + make + +5. Downloading and Flashing Images + +5.0 Download over serial line using Kermit: + + loadb + [Drop to kermit: + ^\c + send <u-boot-bin-image> + c + ] + + + Or via tftp: + + tftp 40000 u-boot.bin + +5.1 Reflash U-boot Image using U-boot + + tftp 40000 u-boot.bin + protect off fe000000 fe1fffff + erase fe000000 fe1fffff + + cp.b 40000 fe000000 xxxx + +You have to supply the correct byte count with 'xxxx' from the TFTP result log. + +6. Notes + 1) The console baudrate for MPC837XEMDS is 115200bps. -- 1.5.1

1 0

[U-Boot-Users] [PATCH 3/6] mpc83xx: Add the support of MPC837xEMDS board
by Dave Liu 18 Sep '07

18 Sep '07

The MPC837xEMDS board support: * DDR2 400MHz hardcoded and SPD init * Local bus NOR Flash * I2C, UART, MII and RTC * eTSEC RGMII * PCI host Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- Makefile | 10 + board/freescale/mpc837xemds/Makefile | 50 +++ board/freescale/mpc837xemds/config.mk | 28 ++ board/freescale/mpc837xemds/mpc837xemds.c | 144 +++++++ board/freescale/mpc837xemds/pci.c | 65 +++ cpu/mpc83xx/cpu_init.c | 6 +- cpu/mpc83xx/spd_sdram.c | 7 +- drivers/tsec.c | 10 + include/configs/MPC837XEMDS.h | 605 +++++++++++++++++++++++++++++ 9 files changed, 922 insertions(+), 3 deletions(-) create mode 100644 board/freescale/mpc837xemds/Makefile create mode 100644 board/freescale/mpc837xemds/config.mk create mode 100644 board/freescale/mpc837xemds/mpc837xemds.c create mode 100644 board/freescale/mpc837xemds/pci.c create mode 100644 include/configs/MPC837XEMDS.h diff --git a/Makefile b/Makefile index 85885b1..f33302f 100644 --- a/Makefile +++ b/Makefile @@ -1829,6 +1829,16 @@ MPC8360EMDS_SLAVE_config: unconfig fi ; @$(MKCONFIG) -a MPC8360EMDS ppc mpc83xx mpc8360emds freescale +MPC837XEMDS_config \ +MPC837XEMDS_HOST_config: unconfig + @mkdir -p $(obj)include + @echo "" >$(obj)include/config.h ; \ + if [ "$(findstring _HOST_,$@)" ] ; then \ + echo -n "... PCI HOST " ; \ + echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \ + fi ; + @$(MKCONFIG) -a MPC837XEMDS ppc mpc83xx mpc837xemds freescale + sbc8349_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349 diff --git a/board/freescale/mpc837xemds/Makefile b/board/freescale/mpc837xemds/Makefile new file mode 100644 index 0000000..5ec7a87 --- /dev/null +++ b/board/freescale/mpc837xemds/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o pci.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc837xemds/config.mk b/board/freescale/mpc837xemds/config.mk new file mode 100644 index 0000000..63c5fc3 --- /dev/null +++ b/board/freescale/mpc837xemds/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# MPC837xEMDS +# + +TEXT_BASE = 0xFE000000 diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c new file mode 100644 index 0000000..0e4ec02 --- /dev/null +++ b/board/freescale/mpc837xemds/mpc837xemds.c @@ -0,0 +1,144 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * Dave Liu <daveliu(a)freescale.com> + * + * CREDITS: Kim Phillips contribute to LIBFDT code + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <common.h> +#include <i2c.h> +#include <spd.h> +#if defined(CONFIG_SPD_EEPROM) +#include <spd_sdram.h> +#endif +#if defined(CONFIG_OF_FLAT_TREE) +#include <ft_build.h> +#elif defined(CONFIG_OF_LIBFDT) +#include <libfdt.h> +#endif +#if defined(CONFIG_PQ_MDS_PIB) +#include "../common/pq-mds-pib.h" +#endif + +int board_early_init_f(void) +{ + u8 *bcsr = (u8 *)CFG_BCSR; + + /* Enable flash write */ + bcsr[0x9] &= ~0x04; + /* Clear all of the interrupt of BCSR */ + bcsr[0xe] = 0xff; + + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_PQ_MDS_PIB + pib_init(); +#endif + return 0; +} + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif +int fixed_sdram(void); + +long int initdram(int board_type) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) + return -1; + +#if defined(CONFIG_SPD_EEPROM) + msize = spd_sdram(); +#else + msize = fixed_sdram(); +#endif + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) + /* Initialize DDR ECC byte */ + ddr_enable_ecc(msize * 1024 * 1024); +#endif + + /* return total bus DDR size(bytes) */ + return (msize * 1024 * 1024); +} + +#if !defined(CONFIG_SPD_EEPROM) +/************************************************************************* + * fixed sdram init -- doesn't use serial presence detect. + ************************************************************************/ +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + u32 msize = CFG_DDR_SIZE * 1024 * 1024; + u32 msize_log2 = __ilog2(msize); + + im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12; + im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1); + +#if (CFG_DDR_SIZE != 512) +#warning Currenly any ddr size other than 512 is not supported +#endif + im->sysconf.ddrcdr = CFG_DDRCDR_VALUE; + udelay(50000); + + im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL; + udelay(1000); + + im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS; + im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG; + udelay(1000); + + im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0; + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3; + im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG; + im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CFG_DDR_MODE; + im->ddr.sdram_mode2 = CFG_DDR_MODE2; + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + __asm__ __volatile__("sync"); + udelay(1000); + + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + udelay(2000); + return CFG_DDR_SIZE; +} +#endif /*!CFG_SPD_EEPROM */ + +int checkboard(void) +{ + puts("Board: Freescale MPC837xEMDS\n"); + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#if defined(CONFIG_OF_FLAT_TREE) + u32 *p; + int len; + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +#endif + ft_cpu_setup(blob, bd); +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif +} +#endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/freescale/mpc837xemds/pci.c b/board/freescale/mpc837xemds/pci.c new file mode 100644 index 0000000..ab90979 --- /dev/null +++ b/board/freescale/mpc837xemds/pci.c @@ -0,0 +1,65 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <asm/mmu.h> +#include <asm/io.h> +#include <common.h> +#include <mpc83xx.h> +#include <pci.h> +#include <i2c.h> +#include <asm/fsl_i2c.h> + +#if defined(CONFIG_PCI) +static struct pci_region pci_regions[] = { + { + bus_start: CFG_PCI_MEM_BASE, + phys_start: CFG_PCI_MEM_PHYS, + size: CFG_PCI_MEM_SIZE, + flags: PCI_REGION_MEM | PCI_REGION_PREFETCH + }, + { + bus_start: CFG_PCI_MMIO_BASE, + phys_start: CFG_PCI_MMIO_PHYS, + size: CFG_PCI_MMIO_SIZE, + flags: PCI_REGION_MEM + }, + { + bus_start: CFG_PCI_IO_BASE, + phys_start: CFG_PCI_IO_PHYS, + size: CFG_PCI_IO_SIZE, + flags: PCI_REGION_IO + } +}; + +void pci_init_board(void) +{ + volatile immap_t *immr = (volatile immap_t *)CFG_IMMR; + volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; + volatile law83xx_t *pci_law = immr->sysconf.pcilaw; + struct pci_region *reg[] = { pci_regions }; + + /* Enable all 5 PCI_CLK_OUTPUTS */ + clk->occr |= 0xf8000000; + udelay(2000); + + /* Configure PCI Local Access Windows */ + pci_law[0].bar = CFG_PCI_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB; + + pci_law[1].bar = CFG_PCI_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB; + + udelay(2000); + + mpc83xx_pci_init(1, reg, 0); +} +#endif /* CONFIG_PCI */ diff --git a/cpu/mpc83xx/cpu_init.c b/cpu/mpc83xx/cpu_init.c index 7224979..2b92be0 100644 --- a/cpu/mpc83xx/cpu_init.c +++ b/cpu/mpc83xx/cpu_init.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -155,6 +155,10 @@ void cpu_init_f (volatile immap_t * im) #ifdef CFG_DDRCDR im->sysconf.ddrcdr = CFG_DDRCDR; #endif + /* Output buffer impedance register */ +#ifdef CFG_OBIR + im->sysconf.obir = CFG_OBIR; +#endif #ifdef CONFIG_QE /* Config QE ioports */ diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c index ee2d038..29dd470 100644 --- a/cpu/mpc83xx/spd_sdram.c +++ b/cpu/mpc83xx/spd_sdram.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2006 Freescale Semiconductor, Inc. + * (C) Copyright 2006-2007 Freescale Semiconductor, Inc. * * (C) Copyright 2006 * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. @@ -198,6 +198,7 @@ long int spd_sdram() if(spd.mem_type == SPD_MEMTYPE_DDR2) { immap->sysconf.ddrcdr = CFG_DDRCDR_VALUE; } + udelay(50000); #endif /* @@ -576,7 +577,7 @@ long int spd_sdram() if (effective_data_rate == 266 || effective_data_rate == 333) { cpo = 0x7; /* READ_LAT + 5/4 */ } else if (effective_data_rate == 400) { - cpo = 0x9; /* READ_LAT + 7/4 */ + cpo = 0x7; /* READ_LAT + 5/4 */ } else { /* Automatic calibration */ cpo = 0x1f; @@ -705,9 +706,11 @@ long int spd_sdram() * SDRAM Cfg 2 */ odt_cfg = 0; +#ifndef CONFIG_NEVER_ASSERT_ODT_TO_CPU if (odt_rd_cfg | odt_wr_cfg) { odt_cfg = 0x2; /* ODT to IOs during reads */ } +#endif if (spd.mem_type == SPD_MEMTYPE_DDR2) { ddr->sdram_cfg2 = (0 | (0 << 26) /* True DQS */ diff --git a/drivers/tsec.c b/drivers/tsec.c index 4ff3339..8426857 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -671,6 +671,15 @@ uint mii_cis8204_setmode(uint mii_reg, struct tsec_private * priv) return MIIM_CIS8204_EPHYCON_INIT; } +uint mii_m88e1111s_setmode(uint mii_reg, struct tsec_private *priv) +{ + uint mii_data = read_phy_reg(priv, mii_reg); + + if (priv->flags & TSEC_REDUCED) + mii_data = (mii_data & 0xfff0) | 0x000b; + return mii_data; +} + /* Initialized required registers to appropriate values, zeroing * those we don't care about (unless zero is bad, in which case, * choose a more appropriate value) @@ -1030,6 +1039,7 @@ struct phy_info phy_info_M88E1111S = { (struct phy_cmd[]){ /* config */ /* Reset and configure the PHY */ {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {0x1b, 0x848f, &mii_m88e1111s_setmode}, {0x14, 0x0cd2, NULL}, /* Delay RGMII TX and RX */ {MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL}, {MIIM_ANAR, MIIM_ANAR_INIT, NULL}, diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h new file mode 100644 index 0000000..7e34492 --- /dev/null +++ b/include/configs/MPC837XEMDS.h @@ -0,0 +1,605 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * Dave Liu <daveliu(a)freescale.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83XX 1 /* MPC83XX family */ +#define CONFIG_MPC837X 1 /* MPC837X CPU specific */ +#define CONFIG_MPC837XEMDS 1 /* MPC837XEMDS board specific */ + +/* + * System Clock Setup + */ +#ifdef CONFIG_PCISLAVE +#define CONFIG_83XX_PCICLK 66000000 /* in HZ */ +#else +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ +#endif + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 66000000 +#endif + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66MHz, then + * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz + */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_6X1 |\ + HRCWL_CORE_TO_CSB_1_5X1) + +#ifdef CONFIG_PCISLAVE +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_AGENT |\ + HRCWH_PCI1_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LDP_CLEAR) +#else +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LDP_CLEAR) +#endif + +/* + * eTSEC Clock Config + */ +#define CFG_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ +#define CFG_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ + +/* + * System IO Config + */ +#define CFG_SICRH 0x00000000 +#define CFG_SICRL 0x00000000 + +/* + * Output Buffer Impedance + */ +#define CFG_OBIR 0x31100000 + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * IMMR new address + */ +#define CFG_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CFG_83XX_DDR_USES_CS0 +#define CFG_DDRCDR_VALUE 0x80080001 /* ODT 150ohm on SoC */ + +#undef CONFIG_DDR_ECC /* support DDR ECC function */ +#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ + +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ + +#if defined(CONFIG_SPD_EEPROM) +#define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */ +#else +/* + * Manually set up DDR parameters + * WHITE ELECTRONIC DESGGNS - W3HG64M72EEU403PD4 SO-DIMM + * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 + */ +#define CFG_DDR_SIZE 512 /* MB */ +#define CFG_DDR_CS0_BNDS 0x0000001f +#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ + | 0x00010000 /* ODT_WR to CSn */ \ + | CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10 ) + /* 0x80010202 */ +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ + | ( 6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ + | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) + /* 0x00620802 */ +#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ + | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ + | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ + | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ + | (13 << TIMING_CFG1_REFREC_SHIFT ) \ + | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) + /* 0x3935d322 */ +#define CFG_DDR_TIMING_2 ( ( 2 << TIMING_CFG2_ADD_LAT_SHIFT ) \ + | ( 6 << TIMING_CFG2_CPO_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ + | ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ + | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ + | ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) ) + /* 0x231088c8 */ +#define CFG_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ + | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) + /* 0x03E00100 */ +#define CFG_DDR_SDRAM_CFG 0x43000000 +#define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ +#define CFG_DDR_MODE ( ( 0x0450 << SDRAM_MODE_ESD_SHIFT ) \ + | ( 0x1432 << SDRAM_MODE_SD_SHIFT ) ) + /* ODT 150ohm CL=3, AL=2 on SDRAM */ +#define CFG_DDR_MODE2 0x00000000 +#endif + +/* + * Memory test + */ +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00040000 /* memtest region */ +#define CFG_MEMTEST_END 0x00140000 + +/* + * The reserved memory + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) +#define CFG_LBC_LBCR 0x00000000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */ + +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) /* valid */ +#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ + OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ + OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * BCSR on the Local Bus + */ +#define CFG_BCSR 0xF8000000 +#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ +#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ + +#define CFG_BR1_PRELIM (CFG_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */ +#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ + +/* + * NAND Flash on the Local Bus + */ +#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CFG_BR3_PRELIM ( CFG_NAND_BASE \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V ) /* valid */ +#define CFG_OR3_PRELIM ( 0xFFFF8000 /* length 32K */ \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR ) + /* 0xFFFF8396 */ + +#define CFG_LBLAWBAR3_PRELIM CFG_NAND_BASE +#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_HAS_BD_T 1 +#define CONFIG_OF_HAS_UBOOT_ENV 1 + +#define OF_CPU "PowerPC,837x@0" +#define OF_SOC "soc837x@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc837x@e0000000/serial@4500" + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI_MEM_BASE 0x80000000 +#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE +#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_MMIO_BASE 0x90000000 +#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE +#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_IO_BASE 0xE0300000 +#define CFG_PCI_IO_PHYS 0xE0300000 +#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE +#define CFG_PCI_SLV_MEM_BUS 0x00000000 +#define CFG_PCI_SLV_MEM_SIZE 0x80000000 + +#ifdef CONFIG_PCI +#define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ +#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#endif /* CONFIG_PCI */ + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 3 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC1" + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_DATE + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CFG_RAMBOOT) + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS +#endif + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CFG_HID2 HID2_HBE + +/* + * Cache Config + */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ +#endif + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CFG_SDRAM_LOWER CFG_SDRAM_BASE +#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) + +#define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +#define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ +#define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +/* BCSR: cache-inhibit and guarded */ +#define CFG_IBAT3L (CFG_BCSR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT3U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT4U CFG_IBAT4U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) +#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#else +#define CFG_IBAT6L (0) +#define CFG_IBAT6U (0) +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 00:E0:0C:00:83:79 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:00:83:78 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=ramfs.83xx\0" \ + "fdtaddr=400000\0" \ + "fdtfile=mpc837xemds.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ -- 1.5.1

1 0

[U-Boot-Users] [PATCH 2/6] mpc83xx: Add the support of MPC8315E SoC
by Dave Liu 18 Sep '07

18 Sep '07

The MPC8315E SoC including e300c3 core and new IP blocks, such as TDM, PCI Express and SATA controller. Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- cpu/mpc83xx/cpu.c | 12 +++++ cpu/mpc83xx/speed.c | 40 ++++++++++++++++- include/asm-ppc/global_data.h | 5 ++ include/asm-ppc/immap_83xx.h | 61 ++++++++++++++++++++++++++- include/mpc83xx.h | 93 ++++++++++++++++++++++++++++++++++++++--- 5 files changed, 201 insertions(+), 10 deletions(-) diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index 5adb4d4..3c19e8d 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -152,6 +152,18 @@ int checkcpu(void) case SPR_8313E_REV10: puts("MPC8313E, "); break; + case SPR_8315E_REV10: + puts("MPC8315E, "); + break; + case SPR_8315_REV10: + puts("MPC8315, "); + break; + case SPR_8314E_REV10: + puts("MPC8314E, "); + break; + case SPR_8314_REV10: + puts("MPC8314, "); + break; case SPR_8379E_REV10: puts("MPC8379E, "); break; diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c index 23dfb30..4f5a866 100644 --- a/cpu/mpc83xx/speed.c +++ b/cpu/mpc83xx/speed.c @@ -113,6 +113,9 @@ int get_clocks(void) #if !defined(CONFIG_MPC832X) u32 i2c2_clk; #endif +#if defined(CONFIG_MPC8315) + u32 tdm_clk; +#endif #if defined(CONFIG_MPC837X) u32 sdhc_clk; #endif @@ -132,6 +135,8 @@ int get_clocks(void) #if defined(CONFIG_MPC837X) u32 pciexp1_clk; u32 pciexp2_clk; +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) u32 sata_clk; #endif @@ -197,7 +202,7 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC837X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) { case 0: tsec2_clk = 0; @@ -215,7 +220,7 @@ int get_clocks(void) /* unkown SCCR_TSEC2CM value */ return -4; } -#elif defined(CONFIG_MPC831X) +#elif defined(CONFIG_MPC8313) tsec2_clk = tsec1_clk; if (!(sccr & SCCR_TSEC1ON)) @@ -288,6 +293,25 @@ int get_clocks(void) return -8; } #endif +#if defined(CONFIG_MPC8315) + switch ((sccr & SCCR_TDMCM) >> SCCR_TDMCM_SHIFT) { + case 0: + tdm_clk = 0; + break; + case 1: + tdm_clk = csb_clk; + break; + case 2: + tdm_clk = csb_clk / 2; + break; + case 3: + tdm_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_TDMCM value */ + return -8; + } +#endif #if defined(CONFIG_MPC834X) i2c1_clk = tsec2_clk; @@ -342,7 +366,7 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC837X) +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) switch ((sccr & SCCR_SATA1CM) >> SCCR_SATA1CM_SHIFT) { case 0: sata_clk = 0; @@ -428,6 +452,9 @@ int get_clocks(void) #if defined(CONFIG_MPC834X) gd->usbmph_clk = usbmph_clk; #endif +#if defined(CONFIG_MPC8315) + gd->tdm_clk = tdm_clk; +#endif #if defined(CONFIG_MPC837X) gd->sdhc_clk = sdhc_clk; #endif @@ -450,6 +477,8 @@ int get_clocks(void) #if defined(CONFIG_MPC837X) gd->pciexp1_clk = pciexp1_clk; gd->pciexp2_clk = pciexp2_clk; +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) gd->sata_clk = sata_clk; #endif gd->pci_clk = pci_sync_in; @@ -488,6 +517,9 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if !defined(CONFIG_MPC832X) printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000); #endif +#if defined(CONFIG_MPC8315) + printf(" TDM: %4d MHz\n", gd->tdm_clk / 1000000); +#endif #if defined(CONFIG_MPC837X) printf(" SDHC: %4d MHz\n", gd->sdhc_clk / 1000000); #endif @@ -502,6 +534,8 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if defined(CONFIG_MPC837X) printf(" PCIEXP1: %4d MHz\n", gd->pciexp1_clk / 1000000); printf(" PCIEXP2: %4d MHz\n", gd->pciexp2_clk / 1000000); +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) printf(" SATA: %4d MHz\n", gd->sata_clk / 1000000); #endif return 0; diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index fab1117..6e8193c 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -63,6 +63,9 @@ typedef struct global_data { #if defined (CONFIG_MPC834X) u32 usbmph_clk; #endif /* CONFIG_MPC834X */ +#if defined(CONFIG_MPC815) + u32 tdm_clk; +#endif #if defined(CONFIG_MPC837X) u32 sdhc_clk; #endif @@ -77,6 +80,8 @@ typedef struct global_data { #if defined(CONFIG_MPC837X) u32 pciexp1_clk; u32 pciexp2_clk; +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) u32 sata_clk; #endif #if defined(CONFIG_MPC8360) diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 7517111..34ea295 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -589,6 +589,20 @@ typedef struct rom83xx { u8 mem[0x10000]; } rom83xx_t; +/* + * TDM + */ +typedef struct tdm83xx { + u8 fixme[0x200]; +} tdm83xx_t; + +/* + * TDM DMAC + */ +typedef struct tdmdmac83xx { + u8 fixme[0x2000]; +} tdmdmac83xx_t; + #if defined(CONFIG_MPC834X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ @@ -626,7 +640,7 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; -#elif defined(CONFIG_MPC831X) +#elif defined(CONFIG_MPC8313) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -661,6 +675,51 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; +#elif defined(CONFIG_MPC8315) +typedef struct immap { + sysconf83xx_t sysconf; /* System configuration */ + wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ + rtclk83xx_t rtc; /* Real Time Clock Module Registers */ + rtclk83xx_t pit; /* Periodic Interval Timer */ + gtm83xx_t gtm[2]; /* Global Timers Module */ + ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */ + arbiter83xx_t arbiter; /* System Arbiter Registers */ + reset83xx_t reset; /* Reset Module */ + clk83xx_t clk; /* System Clock Module */ + pmc83xx_t pmc; /* Power Management Control Module */ + gpio83xx_t gpio[1]; /* General purpose I/O module */ + u8 res0[0x1300]; + ddr83xx_t ddr; /* DDR Memory Controller Memory */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ + u8 res1[0x1300]; + duart83xx_t duart[2]; /* DUART */ + u8 res2[0x900]; + lbus83xx_t lbus; /* Local Bus Controller Registers */ + u8 res3[0x1000]; + spi83xx_t spi; /* Serial Peripheral Interface */ + dma83xx_t dma; /* DMA */ + pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */ + u8 res4[0x80]; + ios83xx_t ios; /* Sequencer */ + pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */ + u8 res5[0xa00]; + pex83xx_t pciexp[2]; /* PCI Express Controller */ + u8 res6[0xb000]; + tdm83xx_t tdm; /* TDM Controller */ + u8 res7[0x1e00]; + sata83xx_t sata[2]; /* SATA Controller */ + u8 res8[0x9000]; + usb83xx_t usb[1]; /* USB DR Controller */ + tsec83xx_t tsec[2]; + u8 res9[0x6000]; + tdmdmac83xx_t tdmdmac; /* TDM DMAC */ + u8 res10[0x2000]; + security83xx_t security; + u8 res11[0xA3000]; + serdes83xx_t serdes[1]; /* SerDes Registers */ + u8 res12[0x1CF00]; +} immap_t; + #elif defined(CONFIG_MPC837X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 4c23094..dba1aea 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -102,6 +102,10 @@ #define SPR_8313_REV10 0x80B10010 #define SPR_8311E_REV10 0x80B20010 #define SPR_8311_REV10 0x80B30010 +#define SPR_8315E_REV10 0x80B40010 +#define SPR_8315_REV10 0x80B50010 +#define SPR_8314E_REV10 0x80B60010 +#define SPR_8314_REV10 0x80B70010 #define SPR_8379E_REV10 0x80C20010 #define SPR_8379_REV10 0x80C30010 @@ -220,8 +224,8 @@ #define SICRL_URT_CTPR 0x06000000 #define SICRL_IRQ_CTPR 0x00C00000 -#elif defined(CONFIG_MPC831X) -/* SICRL bits - MPC831x specific */ +#elif defined(CONFIG_MPC8313) +/* SICRL bits - MPC8313 specific */ #define SICRL_LBC 0x30000000 #define SICRL_UART 0x0C000000 #define SICRL_SPI_A 0x03000000 @@ -232,7 +236,7 @@ #define SICRL_ETSEC1_A 0x0000000C #define SICRL_ETSEC2_A 0x00000003 -/* SICRH bits - MPC831x specific */ +/* SICRH bits - MPC8313 specific */ #define SICRH_INTR_A 0x02000000 #define SICRH_INTR_B 0x00C00000 #define SICRH_IIC 0x00300000 @@ -249,6 +253,41 @@ #define SICRH_TSOBI1 0x00000002 #define SICRH_TSOBI2 0x00000001 +#elif defined(CONFIG_MPC8315) +/* SICRL bits - MPC8315 specific */ +#define SICRL_DMA_CH0 0xc0000000 +#define SICRL_DMA_SPI 0x30000000 +#define SICRL_UART 0x0c000000 +#define SICRL_IRQ4 0x02000000 +#define SICRL_IRQ5 0x01800000 +#define SICRL_IRQ6_7 0x00400000 +#define SICRL_IIC1 0x00300000 +#define SICRL_TDM 0x000c0000 +#define SICRL_TDM_SHARED 0x00030000 +#define SICRL_PCI_A 0x0000c000 +#define SICRL_ELBC_A 0x00003000 +#define SICRL_ETSEC1_A 0x000000c0 +#define SICRL_ETSEC1_B 0x00000030 +#define SICRL_ETSEC1_C 0x0000000c +#define SICRL_TSEXPOBI 0x00000001 + +/* SICRH bits - MPC8315 specific */ +#define SICRH_GPIO_0 0xc0000000 +#define SICRH_GPIO_1 0x30000000 +#define SICRH_GPIO_2 0x0c000000 +#define SICRH_GPIO_3 0x03000000 +#define SICRH_GPIO_4 0x00c00000 +#define SICRH_GPIO_5 0x00300000 +#define SICRH_GPIO_6 0x000c0000 +#define SICRH_GPIO_7 0x00030000 +#define SICRH_GPIO_8 0x0000c000 +#define SICRH_GPIO_9 0x00003000 +#define SICRH_GPIO_10 0x00000c00 +#define SICRH_GPIO_11 0x00000300 +#define SICRH_ETSEC2_A 0x000000c0 +#define SICRH_TSOBI1 0x00000002 +#define SICRH_TSOBI2 0x00000001 + #elif defined(CONFIG_MPC837X) /* SICRL bits - MPC837x specific */ #define SICRL_USB_A 0xC0000000 @@ -447,7 +486,7 @@ #define HRCWL_CE_TO_PLL_1X30 0x0000001E #define HRCWL_CE_TO_PLL_1X31 0x0000001F -#elif defined(CONFIG_MPC837X) +#elif defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) #define HRCWL_SVCOD 0x30000000 #define HRCWL_SVCOD_SHIFT 28 #define HRCWL_SVCOD_DIV_4 0x00000000 @@ -556,7 +595,7 @@ /* RSR - Reset Status Register */ -#if defined(CONFIG_MPC837X) +#if defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) #define RSR_RSTSRC 0xF0000000 /* Reset source */ #define RSR_RSTSRC_SHIFT 28 #else @@ -677,7 +716,7 @@ #define SCCR_USBCM_2 0x00A00000 #define SCCR_USBCM_3 0x00F00000 -#elif defined(CONFIG_MPC831X) +#elif defined(CONFIG_MPC8313) /* TSEC1 bits are for TSEC2 as well */ #define SCCR_TSEC1CM 0xc0000000 #define SCCR_TSEC1CM_SHIFT 30 @@ -697,6 +736,48 @@ #define SCCR_USBDRCM_2 0x00200000 #define SCCR_USBDRCM_3 0x00300000 +#elif defined(CONFIG_MPC8315) +/* SCCR bits - MPC8315 specific */ +#define SCCR_TSEC1CM 0xc0000000 +#define SCCR_TSEC1CM_SHIFT 30 +#define SCCR_TSEC1CM_0 0x00000000 +#define SCCR_TSEC1CM_1 0x40000000 +#define SCCR_TSEC1CM_2 0x80000000 +#define SCCR_TSEC1CM_3 0xC0000000 + +#define SCCR_TSEC2CM 0x30000000 +#define SCCR_TSEC2CM_SHIFT 28 +#define SCCR_TSEC2CM_0 0x00000000 +#define SCCR_TSEC2CM_1 0x10000000 +#define SCCR_TSEC2CM_2 0x20000000 +#define SCCR_TSEC2CM_3 0x30000000 + +#define SCCR_USBDRCM 0x00300000 +#define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBDRCM_0 0x00000000 +#define SCCR_USBDRCM_1 0x00100000 +#define SCCR_USBDRCM_2 0x00200000 +#define SCCR_USBDRCM_3 0x00300000 + +#define SCCR_PCIEXP1CM 0x00080000 +#define SCCR_PCIEXP2CM 0x00040000 + +#define SCCR_SATA1CM 0x0000c000 +#define SCCR_SATA1CM_SHIFT 14 +#define SCCR_SATACM 0x0000f000 +#define SCCR_SATACM_SHIFT 8 +#define SCCR_SATACM_0 0x00000000 +#define SCCR_SATACM_1 0x00005000 +#define SCCR_SATACM_2 0x0000a000 +#define SCCR_SATACM_3 0x0000f000 + +#define SCCR_TDMCM 0x000000c0 +#define SCCR_TDMCM_SHIFT 6 +#define SCCR_TDMCM_0 0x00000000 +#define SCCR_TDMCM_1 0x00000040 +#define SCCR_TDMCM_2 0x00000080 +#define SCCR_TDMCM_3 0x000000c0 + #elif defined(CONFIG_MPC837X) /* SCCR bits - MPC837x specific */ #define SCCR_TSEC1CM 0xc0000000 -- 1.5.1

1 0

[U-Boot-Users] [PATCH 1/6] mpc83xx: Add the support of MPC837x SoC
by Dave Liu 18 Sep '07

18 Sep '07

The MPC837x SoC including e300c4 core and new IP blocks, such as SDHC, PCI Express and SATA controller. Signed-off-by: Dave Liu <daveliu(a)freescale.com> --- cpu/mpc83xx/cpu.c | 24 ++++++- cpu/mpc83xx/speed.c | 167 ++++++++++++++++++++++++++++++++------- include/asm-ppc/global_data.h | 10 ++- include/asm-ppc/immap_83xx.h | 84 +++++++++++++++++++- include/mpc83xx.h | 174 ++++++++++++++++++++++++++++++++++++----- 5 files changed, 406 insertions(+), 53 deletions(-) diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index e634f0a..5adb4d4 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -64,6 +64,10 @@ int checkcpu(void) printf("e300c3, "); break; + case PVR_E300C4: + printf("e300c4, "); + break; + default: printf("Unknown core, "); } @@ -148,6 +152,24 @@ int checkcpu(void) case SPR_8313E_REV10: puts("MPC8313E, "); break; + case SPR_8379E_REV10: + puts("MPC8379E, "); + break; + case SPR_8379_REV10: + puts("MPC8379, "); + break; + case SPR_8378E_REV10: + puts("MPC8378E, "); + break; + case SPR_8378_REV10: + puts("MPC8378, "); + break; + case SPR_8377E_REV10: + puts("MPC8377E, "); + break; + case SPR_8377_REV10: + puts("MPC8377, "); + break; default: printf("Rev: Unknown revision number:%08x\n" "Warning: Unsupported cpu revision!\n",spridr); diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c index cba57fa..23dfb30 100644 --- a/cpu/mpc83xx/speed.c +++ b/cpu/mpc83xx/speed.c @@ -2,7 +2,7 @@ * (C) Copyright 2000-2002 * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. * - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -100,7 +100,7 @@ int get_clocks(void) u32 lcrr; u32 csb_clk; -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) u32 tsec1_clk; u32 tsec2_clk; u32 usbdr_clk; @@ -113,6 +113,9 @@ int get_clocks(void) #if !defined(CONFIG_MPC832X) u32 i2c2_clk; #endif +#if defined(CONFIG_MPC837X) + u32 sdhc_clk; +#endif u32 enc_clk; u32 lbiu_clk; u32 lclk_clk; @@ -126,6 +129,11 @@ int get_clocks(void) u32 qe_clk; u32 brg_clk; #endif +#if defined(CONFIG_MPC837X) + u32 pciexp1_clk; + u32 pciexp2_clk; + u32 sata_clk; +#endif if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) return -1; @@ -151,7 +159,7 @@ int get_clocks(void) sccr = im->clk.sccr; -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) switch ((sccr & SCCR_TSEC1CM) >> SCCR_TSEC1CM_SHIFT) { case 0: tsec1_clk = 0; @@ -167,7 +175,7 @@ int get_clocks(void) break; default: /* unkown SCCR_TSEC1CM value */ - return -4; + return -2; } switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) { @@ -185,11 +193,11 @@ int get_clocks(void) break; default: /* unkown SCCR_USBDRCM value */ - return -8; + return -3; } #endif -#if defined(CONFIG_MPC834X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC837X) switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) { case 0: tsec2_clk = 0; @@ -205,11 +213,18 @@ int get_clocks(void) break; default: /* unkown SCCR_TSEC2CM value */ - return -5; + return -4; } +#elif defined(CONFIG_MPC831X) + tsec2_clk = tsec1_clk; - i2c1_clk = tsec2_clk; + if (!(sccr & SCCR_TSEC1ON)) + tsec1_clk = 0; + if (!(sccr & SCCR_TSEC2ON)) + tsec2_clk = 0; +#endif +#if defined(CONFIG_MPC834X) switch ((sccr & SCCR_USBMPHCM) >> SCCR_USBMPHCM_SHIFT) { case 0: usbmph_clk = 0; @@ -225,7 +240,7 @@ int get_clocks(void) break; default: /* unkown SCCR_USBMPHCM value */ - return -7; + return -5; } if (usbmph_clk != 0 && usbdr_clk != 0 && usbmph_clk != usbdr_clk) { @@ -233,42 +248,120 @@ int get_clocks(void) * USB DR clock is not disabled then * USB MPH & USB DR must have the same rate */ - return -9; + return -6; + } +#endif + switch ((sccr & SCCR_ENCCM) >> SCCR_ENCCM_SHIFT) { + case 0: + enc_clk = 0; + break; + case 1: + enc_clk = csb_clk; + break; + case 2: + enc_clk = csb_clk / 2; + break; + case 3: + enc_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_ENCCM value */ + return -7; } -#elif defined(CONFIG_MPC831X) - tsec2_clk = tsec1_clk; - if (!(sccr & SCCR_TSEC1ON)) - tsec1_clk = 0; - if (!(sccr & SCCR_TSEC2ON)) - tsec2_clk = 0; +#if defined(CONFIG_MPC837X) + switch ((sccr & SCCR_SDHCCM) >> SCCR_SDHCCM_SHIFT) { + case 0: + sdhc_clk = 0; + break; + case 1: + sdhc_clk = csb_clk; + break; + case 2: + sdhc_clk = csb_clk / 2; + break; + case 3: + sdhc_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_SDHCCM value */ + return -8; + } #endif -#if !defined(CONFIG_MPC834X) +#if defined(CONFIG_MPC834X) + i2c1_clk = tsec2_clk; +#elif defined(CONFIG_MPC8360) i2c1_clk = csb_clk; +#elif defined(CONFIG_MPC832X) + i2c1_clk = enc_clk; +#elif defined(CONFIG_MPC831X) + i2c1_clk = enc_clk; +#elif defined(CONFIG_MPC837X) + i2c1_clk = sdhc_clk; #endif #if !defined(CONFIG_MPC832X) - i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */ + i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */ #endif - switch ((sccr & SCCR_ENCCM) >> SCCR_ENCCM_SHIFT) { +#if defined(CONFIG_MPC837X) + switch ((sccr & SCCR_PCIEXP1CM) >> SCCR_PCIEXP1CM_SHIFT) { case 0: - enc_clk = 0; + pciexp1_clk = 0; break; case 1: - enc_clk = csb_clk; + pciexp1_clk = csb_clk; break; case 2: - enc_clk = csb_clk / 2; + pciexp1_clk = csb_clk / 2; break; case 3: - enc_clk = csb_clk / 3; + pciexp1_clk = csb_clk / 3; break; default: - /* unkown SCCR_ENCCM value */ - return -6; + /* unkown SCCR_PCIEXP1CM value */ + return -9; } + switch ((sccr & SCCR_PCIEXP2CM) >> SCCR_PCIEXP2CM_SHIFT) { + case 0: + pciexp2_clk = 0; + break; + case 1: + pciexp2_clk = csb_clk; + break; + case 2: + pciexp2_clk = csb_clk / 2; + break; + case 3: + pciexp2_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_PCIEXP2CM value */ + return -10; + } +#endif + +#if defined(CONFIG_MPC837X) + switch ((sccr & SCCR_SATA1CM) >> SCCR_SATA1CM_SHIFT) { + case 0: + sata_clk = 0; + break; + case 1: + sata_clk = csb_clk; + break; + case 2: + sata_clk = csb_clk / 2; + break; + case 3: + sata_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_SATA1CM value */ + return -11; + } +#endif + lbiu_clk = csb_clk * (1 + ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT)); lcrr = (im->lbus.lcrr & LCRR_CLKDIV) >> LCRR_CLKDIV_SHIFT; @@ -280,7 +373,7 @@ int get_clocks(void) break; default: /* unknown lcrr */ - return -10; + return -12; } ddr_clk = csb_clk * @@ -316,7 +409,7 @@ int get_clocks(void) break; default: /* unkown core to csb ratio */ - return -12; + return -13; } #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) @@ -327,7 +420,7 @@ int get_clocks(void) #endif gd->csb_clk = csb_clk; -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) gd->tsec1_clk = tsec1_clk; gd->tsec2_clk = tsec2_clk; gd->usbdr_clk = usbdr_clk; @@ -335,6 +428,9 @@ int get_clocks(void) #if defined(CONFIG_MPC834X) gd->usbmph_clk = usbmph_clk; #endif +#if defined(CONFIG_MPC837X) + gd->sdhc_clk = sdhc_clk; +#endif gd->core_clk = core_clk; gd->i2c1_clk = i2c1_clk; #if !defined(CONFIG_MPC832X) @@ -351,6 +447,11 @@ int get_clocks(void) gd->qe_clk = qe_clk; gd->brg_clk = brg_clk; #endif +#if defined(CONFIG_MPC837X) + gd->pciexp1_clk = pciexp1_clk; + gd->pciexp2_clk = pciexp2_clk; + gd->sata_clk = sata_clk; +#endif gd->pci_clk = pci_sync_in; gd->cpu_clk = gd->core_clk; gd->bus_clk = gd->csb_clk; @@ -387,7 +488,10 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if !defined(CONFIG_MPC832X) printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000); #endif -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC837X) + printf(" SDHC: %4d MHz\n", gd->sdhc_clk / 1000000); +#endif +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) printf(" TSEC1: %4d MHz\n", gd->tsec1_clk / 1000000); printf(" TSEC2: %4d MHz\n", gd->tsec2_clk / 1000000); printf(" USB DR: %4d MHz\n", gd->usbdr_clk / 1000000); @@ -395,6 +499,11 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if defined(CONFIG_MPC834X) printf(" USB MPH: %4d MHz\n", gd->usbmph_clk / 1000000); #endif +#if defined(CONFIG_MPC837X) + printf(" PCIEXP1: %4d MHz\n", gd->pciexp1_clk / 1000000); + printf(" PCIEXP2: %4d MHz\n", gd->pciexp2_clk / 1000000); + printf(" SATA: %4d MHz\n", gd->sata_clk / 1000000); +#endif return 0; } diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index 4676e2c..fab1117 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -55,7 +55,7 @@ typedef struct global_data { #if defined(CONFIG_MPC83XX) /* There are other clocks in the MPC83XX */ u32 csb_clk; -#if defined (CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) u32 tsec1_clk; u32 tsec2_clk; u32 usbdr_clk; @@ -63,6 +63,9 @@ typedef struct global_data { #if defined (CONFIG_MPC834X) u32 usbmph_clk; #endif /* CONFIG_MPC834X */ +#if defined(CONFIG_MPC837X) + u32 sdhc_clk; +#endif u32 core_clk; u32 i2c1_clk; u32 i2c2_clk; @@ -71,6 +74,11 @@ typedef struct global_data { u32 lclk_clk; u32 ddr_clk; u32 pci_clk; +#if defined(CONFIG_MPC837X) + u32 pciexp1_clk; + u32 pciexp2_clk; + u32 sata_clk; +#endif #if defined(CONFIG_MPC8360) u32 ddr_sec_clk; #endif /* CONFIG_MPC8360 */ diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 0de9338..7517111 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2004-2006 Freescale Semiconductor, Inc. + * (C) Copyright 2004-2007 Freescale Semiconductor, Inc. * * MPC83xx Internal Memory Map * @@ -63,7 +63,8 @@ typedef struct sysconf83xx { u8 res6[0x0C]; u32 ddrcdr; /* DDR Control Driver Register */ u32 ddrdsr; /* DDR Debug Status Register */ - u8 res7[0xD0]; + u32 obir; /* Output Buffer Impedance Register */ + u8 res7[0xCC]; } sysconf83xx_t; /* @@ -553,6 +554,41 @@ typedef struct security83xx { u8 fixme[0x10000]; } security83xx_t; +/* + * PCI Express + */ +typedef struct pex83xx { + u8 fixme[0x1000]; +} pex83xx_t; + +/* + * SATA + */ +typedef struct sata83xx { + u8 fixme[0x1000]; +} sata83xx_t; + +/* + * eSDHC + */ +typedef struct sdhc83xx { + u8 fixme[0x1000]; +} sdhc83xx_t; + +/* + * SerDes + */ +typedef struct serdes83xx { + u8 fixme[0x100]; +} serdes83xx_t; + +/* + * On Chip ROM + */ +typedef struct rom83xx { + u8 mem[0x10000]; +} rom83xx_t; + #if defined(CONFIG_MPC834X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ @@ -625,6 +661,50 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; +#elif defined(CONFIG_MPC837X) +typedef struct immap { + sysconf83xx_t sysconf; /* System configuration */ + wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ + rtclk83xx_t rtc; /* Real Time Clock Module Registers */ + rtclk83xx_t pit; /* Periodic Interval Timer */ + gtm83xx_t gtm[2]; /* Global Timers Module */ + ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */ + arbiter83xx_t arbiter; /* System Arbiter Registers */ + reset83xx_t reset; /* Reset Module */ + clk83xx_t clk; /* System Clock Module */ + pmc83xx_t pmc; /* Power Management Control Module */ + gpio83xx_t gpio[2]; /* General purpose I/O module */ + u8 res0[0x1200]; + ddr83xx_t ddr; /* DDR Memory Controller Memory */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ + u8 res1[0x1300]; + duart83xx_t duart[2]; /* DUART */ + u8 res2[0x900]; + lbus83xx_t lbus; /* Local Bus Controller Registers */ + u8 res3[0x1000]; + spi83xx_t spi; /* Serial Peripheral Interface */ + dma83xx_t dma; /* DMA */ + pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */ + u8 res4[0x80]; + ios83xx_t ios; /* Sequencer */ + pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */ + u8 res5[0xa00]; + pex83xx_t pciexp[2]; /* PCI Express Controller */ + u8 res6[0xd000]; + sata83xx_t sata[4]; /* SATA Controller */ + u8 res7[0x7000]; + usb83xx_t usb[1]; /* USB DR Controller */ + tsec83xx_t tsec[2]; + u8 res8[0x8000]; + sdhc83xx_t sdhc; /* SDHC Controller */ + u8 res9[0x1000]; + security83xx_t security; + u8 res10[0xA3000]; + serdes83xx_t serdes[2]; /* SerDes Registers */ + u8 res11[0xCE00]; + rom83xx_t rom; /* On Chip ROM */ +} immap_t; + #elif defined(CONFIG_MPC8360) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 4d32c6a..4c23094 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -98,10 +98,17 @@ #define SPR_8321E_REV11 0x80660011 #define SPR_8321_REV11 0x80670011 -#define SPR_8311_REV10 0x80B30010 -#define SPR_8311E_REV10 0x80B20010 -#define SPR_8313_REV10 0x80B10010 #define SPR_8313E_REV10 0x80B00010 +#define SPR_8313_REV10 0x80B10010 +#define SPR_8311E_REV10 0x80B20010 +#define SPR_8311_REV10 0x80B30010 + +#define SPR_8379E_REV10 0x80C20010 +#define SPR_8379_REV10 0x80C30010 +#define SPR_8378E_REV10 0x80C40010 +#define SPR_8378_REV10 0x80C50010 +#define SPR_8377E_REV10 0x80C60010 +#define SPR_8377_REV10 0x80C70010 /* SPCR - System Priority Configuration Register */ @@ -130,8 +137,8 @@ #define SPCR_TSEC2EP 0x00000003 /* TSEC2 emergency priority */ #define SPCR_TSEC2EP_SHIFT (31-31) -#elif defined(CONFIG_MPC831X) -/* SPCR bits - MPC831x specific */ +#elif defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) +/* SPCR bits - MPC831x and MPC837x specific */ #define SPCR_TSECDP 0x00003000 /* TSEC data priority */ #define SPCR_TSECDP_SHIFT (31-19) #define SPCR_TSECEP 0x00000C00 /* TSEC emergency priority */ @@ -242,6 +249,55 @@ #define SICRH_TSOBI1 0x00000002 #define SICRH_TSOBI2 0x00000001 +#elif defined(CONFIG_MPC837X) +/* SICRL bits - MPC837x specific */ +#define SICRL_USB_A 0xC0000000 +#define SICRL_USB_B 0x30000000 +#define SICRL_UART 0x0C000000 +#define SICRL_GPIO_A 0x02000000 +#define SICRL_GPIO_B 0x01000000 +#define SICRL_GPIO_C 0x00800000 +#define SICRL_GPIO_D 0x00400000 +#define SICRL_GPIO_E 0x00200000 +#define SICRL_GPIO_F 0x00180000 +#define SICRL_GPIO_G 0x00040000 +#define SICRL_GPIO_H 0x00020000 +#define SICRL_GPIO_I 0x00010000 +#define SICRL_GPIO_J 0x00008000 +#define SICRL_GPIO_K 0x00004000 +#define SICRL_GPIO_L 0x00003000 +#define SICRL_DMA_A 0x00000800 +#define SICRL_DMA_B 0x00000400 +#define SICRL_DMA_C 0x00000200 +#define SICRL_DMA_D 0x00000100 +#define SICRL_DMA_E 0x00000080 +#define SICRL_DMA_F 0x00000040 +#define SICRL_DMA_G 0x00000020 +#define SICRL_DMA_H 0x00000010 +#define SICRL_DMA_I 0x00000008 +#define SICRL_DMA_J 0x00000004 +#define SICRL_LDP_A 0x00000002 +#define SICRL_LDP_B 0x00000001 + +/* SICRH bits - MPC837x specific */ +#define SICRH_DDR 0x80000000 +#define SICRH_TSEC1_A 0x10000000 +#define SICRH_TSEC1_B 0x08000000 +#define SICRH_TSEC2_A 0x00400000 +#define SICRH_TSEC2_B 0x00200000 +#define SICRH_TSEC2_C 0x00100000 +#define SICRH_TSEC2_D 0x00080000 +#define SICRH_TSEC2_E 0x00040000 +#define SICRH_TMR 0x00010000 +#define SICRH_GPIO2_A 0x00008000 +#define SICRH_GPIO2_B 0x00004000 +#define SICRH_GPIO2_C 0x00002000 +#define SICRH_GPIO2_D 0x00001000 +#define SICRH_GPIO2_E 0x00000C00 +#define SICRH_GPIO2_F 0x00000300 +#define SICRH_GPIO2_G 0x000000C0 +#define SICRH_GPIO2_H 0x00000030 +#define SICRH_SPI 0x00000003 #endif /* SWCRR - System Watchdog Control Register @@ -390,6 +446,14 @@ #define HRCWL_CE_TO_PLL_1X29 0x0000001D #define HRCWL_CE_TO_PLL_1X30 0x0000001E #define HRCWL_CE_TO_PLL_1X31 0x0000001F + +#elif defined(CONFIG_MPC837X) +#define HRCWL_SVCOD 0x30000000 +#define HRCWL_SVCOD_SHIFT 28 +#define HRCWL_SVCOD_DIV_4 0x00000000 +#define HRCWL_SVCOD_DIV_8 0x10000000 +#define HRCWL_SVCOD_DIV_2 0x20000000 +#define HRCWL_SVCOD_DIV_1 0x30000000 #endif /* HRCWH - Hardware Reset Configuration Word High @@ -436,11 +500,14 @@ #if defined(CONFIG_MPC834X) #define HRCWH_ROM_LOC_PCI2 0x00200000 #endif +#if defined(CONIFG_MPC837X) +#define HRCWH_ROM_LOC_ON_CHIP_ROM 0x00300000 +#endif #define HRCWH_ROM_LOC_LOCAL_8BIT 0x00500000 #define HRCWH_ROM_LOC_LOCAL_16BIT 0x00600000 #define HRCWH_ROM_LOC_LOCAL_32BIT 0x00700000 -#if defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) #define HRCWH_ROM_LOC_NAND_SP_8BIT 0x00100000 #define HRCWH_ROM_LOC_NAND_SP_16BIT 0x00200000 #define HRCWH_ROM_LOC_NAND_LP_8BIT 0x00500000 @@ -489,8 +556,13 @@ /* RSR - Reset Status Register */ +#if defined(CONFIG_MPC837X) +#define RSR_RSTSRC 0xF0000000 /* Reset source */ +#define RSR_RSTSRC_SHIFT 28 +#else #define RSR_RSTSRC 0xE0000000 /* Reset source */ #define RSR_RSTSRC_SHIFT 29 +#endif #define RSR_BSF 0x00010000 /* Boot seq. fail */ #define RSR_BSF_SHIFT 16 #define RSR_SWSR 0x00002000 /* software soft reset */ @@ -577,8 +649,8 @@ #define SCCR_PCICM 0x00010000 #define SCCR_PCICM_SHIFT 16 -/* SCCR bits - MPC8349 specific */ -#ifdef CONFIG_MPC834X +#if defined(CONFIG_MPC834X) +/* SCCR bits - MPC834x specific */ #define SCCR_TSEC1CM 0xc0000000 #define SCCR_TSEC1CM_SHIFT 30 #define SCCR_TSEC1CM_0 0x00000000 @@ -593,6 +665,18 @@ #define SCCR_TSEC2CM_2 0x20000000 #define SCCR_TSEC2CM_3 0x30000000 +/* The MPH must have the same clock ratio as DR, unless its clock disabled */ +#define SCCR_USBMPHCM 0x00c00000 +#define SCCR_USBMPHCM_SHIFT 22 +#define SCCR_USBDRCM 0x00300000 +#define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBCM 0x00f00000 +#define SCCR_USBCM_SHIFT 20 +#define SCCR_USBCM_0 0x00000000 +#define SCCR_USBCM_1 0x00500000 +#define SCCR_USBCM_2 0x00A00000 +#define SCCR_USBCM_3 0x00F00000 + #elif defined(CONFIG_MPC831X) /* TSEC1 bits are for TSEC2 as well */ #define SCCR_TSEC1CM 0xc0000000 @@ -606,17 +690,67 @@ #define SCCR_TSEC2ON 0x10000000 #define SCCR_TSEC2ON_SHIFT 28 -#endif - -#define SCCR_USBMPHCM 0x00c00000 -#define SCCR_USBMPHCM_SHIFT 22 #define SCCR_USBDRCM 0x00300000 #define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBDRCM_0 0x00000000 +#define SCCR_USBDRCM_1 0x00100000 +#define SCCR_USBDRCM_2 0x00200000 +#define SCCR_USBDRCM_3 0x00300000 -#define SCCR_USBCM_0 0x00000000 -#define SCCR_USBCM_1 0x00500000 -#define SCCR_USBCM_2 0x00A00000 -#define SCCR_USBCM_3 0x00F00000 +#elif defined(CONFIG_MPC837X) +/* SCCR bits - MPC837x specific */ +#define SCCR_TSEC1CM 0xc0000000 +#define SCCR_TSEC1CM_SHIFT 30 +#define SCCR_TSEC1CM_0 0x00000000 +#define SCCR_TSEC1CM_1 0x40000000 +#define SCCR_TSEC1CM_2 0x80000000 +#define SCCR_TSEC1CM_3 0xC0000000 + +#define SCCR_TSEC2CM 0x30000000 +#define SCCR_TSEC2CM_SHIFT 28 +#define SCCR_TSEC2CM_0 0x00000000 +#define SCCR_TSEC2CM_1 0x10000000 +#define SCCR_TSEC2CM_2 0x20000000 +#define SCCR_TSEC2CM_3 0x30000000 + +#define SCCR_SDHCCM 0x0c000000 +#define SCCR_SDHCCM_SHIFT 26 +#define SCCR_SDHCCM_0 0x00000000 +#define SCCR_SDHCCM_1 0x04000000 +#define SCCR_SDHCCM_2 0x08000000 +#define SCCR_SDHCCM_3 0x0c000000 + +#define SCCR_USBDRCM 0x00c00000 +#define SCCR_USBDRCM_SHIFT 22 +#define SCCR_USBDRCM_0 0x00000000 +#define SCCR_USBDRCM_1 0x00400000 +#define SCCR_USBDRCM_2 0x00800000 +#define SCCR_USBDRCM_3 0x00c00000 + +#define SCCR_PCIEXP1CM 0x00300000 +#define SCCR_PCIEXP1CM_SHIFT 20 +#define SCCR_PCIEXP1CM_0 0x00000000 +#define SCCR_PCIEXP1CM_1 0x00100000 +#define SCCR_PCIEXP1CM_2 0x00200000 +#define SCCR_PCIEXP1CM_3 0x00300000 + +#define SCCR_PCIEXP2CM 0x000c0000 +#define SCCR_PCIEXP2CM_SHIFT 18 +#define SCCR_PCIEXP2CM_0 0x00000000 +#define SCCR_PCIEXP2CM_1 0x00040000 +#define SCCR_PCIEXP2CM_2 0x00080000 +#define SCCR_PCIEXP2CM_3 0x000c0000 + +/* All of the four SATA controllers must have the same clock ratio */ +#define SCCR_SATA1CM 0x000000c0 +#define SCCR_SATA1CM_SHIFT 6 +#define SCCR_SATACM 0x000000ff +#define SCCR_SATACM_SHIFT 0 +#define SCCR_SATACM_0 0x00000000 +#define SCCR_SATACM_1 0x00000055 +#define SCCR_SATACM_2 0x000000aa +#define SCCR_SATACM_3 0x000000ff +#endif /* CSn_BDNS - Chip Select memory Bounds Register */ @@ -860,7 +994,7 @@ #define BR_MS_UPMA 0x00000080 /* UPMA */ #define BR_MS_UPMB 0x000000A0 /* UPMB */ #define BR_MS_UPMC 0x000000C0 /* UPMC */ -#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) +#if !defined(CONFIG_MPC834X) #define BR_ATOM 0x0000000C #define BR_ATOM_SHIFT 2 #endif @@ -869,7 +1003,7 @@ #if defined(CONFIG_MPC834X) #define BR_RES ~(BR_BA | BR_PS | BR_DECC | BR_WP | BR_MSEL | BR_V) -#elif defined(CONFIG_MPC8360) +#else #define BR_RES ~(BR_BA | BR_PS | BR_DECC | BR_WP | BR_MSEL | BR_ATOM | BR_V) #endif @@ -1255,7 +1389,7 @@ #define LTESR_CS 0x00080000 #define LTESR_CC 0x00000001 -/* DDR Control Driver Register +/* DDRCDR - DDR Control Driver Register */ #define DDRCDR_EN 0x40000000 #define DDRCDR_PZ 0x3C000000 -- 1.5.1

1 0

[U-Boot-Users] Reset issue on mpc85xx
by urwithsughosh＠gmail.com 18 Sep '07

18 Sep '07

Hello, I am working on a custom board having mpc8560 and mpc8540. On porting the v1.3.0-rc1 u-boot, i get a peculiar issue. The board does not reset on giving the 'reset' command. This is observed only on the release candidate version of u-boot. I've also ported the 1.2.0 release and there it works fine. I tried debugging the issue by putting some debug statements, in the board.c file after the init_sequence, and what i observe is that the msr register is getting cleared. But the 1.2.0 version shows the correct value, i.e 0x1200 which is programmed in the start.S. After setting the MSR[DE] bit in the do_reset function along with the DBCR0 register settings, the board resets correctly. Am i missing something. Please throw some light on it. -- sughosh

1 1

[U-Boot-Users] question for u-boot 1.1.4
by 井逍遥 17 Sep '07

17 Sep '07

Hi: We use uboot-1.1.4 on embeded linux 2.6. But we found it not support nand flash with 16bit ,2048 bytes/page(we use sansung k9f1g16u0m). The system cannot boot.If there are some parameters needed to modify,pleaese tell us.Thank you. _________________________________________________________________ Windows Live Spaces 中最年轻的成员！ http://miaomiaogarden2007.spaces.live.com/

2 1

[U-Boot-Users] TQM8xx/FPS8xx: adjust flash partitions for 2.6 ARCH=powerpc kernels
by Wolfgang Denk 17 Sep '07

17 Sep '07

Signed-off-by: Wolfgang Denk <wd(a)denx.de> --- include/configs/FPS850L.h | 60 +++++++++++++++++++++++++++++++------------- include/configs/FPS860L.h | 46 +++++++++++++++++++++++++++------- include/configs/TQM823L.h | 5 ++- include/configs/TQM823M.h | 5 ++- include/configs/TQM850L.h | 5 ++- include/configs/TQM850M.h | 5 ++- include/configs/TQM855L.h | 5 ++- include/configs/TQM855M.h | 5 ++- include/configs/TQM860L.h | 5 ++- include/configs/TQM860M.h | 5 ++- include/configs/TQM862L.h | 5 ++- include/configs/TQM862M.h | 5 ++- include/configs/TQM866M.h | 5 ++- 13 files changed, 111 insertions(+), 50 deletions(-) diff --git a/include/configs/FPS850L.h b/include/configs/FPS850L.h index 322158c..3b0ddb4 100644 --- a/include/configs/FPS850L.h +++ b/include/configs/FPS850L.h @@ -39,28 +39,44 @@ #undef CONFIG_8xx_CONS_SMC1 #define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ #undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 19200 -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_BOOTCOMMAND "bootm 40020000" /* autoboot command */ +#define CONFIG_BAUDRATE 115200 -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ +#define CONFIG_BOOTCOUNT_LIMIT + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #define CONFIG_BOARD_TYPES 1 /* support board types */ -#define CONFIG_BOOTARGS "root=/dev/nfs rw " \ - "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ - "nfsaddrs=10.0.0.99:10.0.0.2" +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "bootfile=/tftpboot/fps850L/uImage\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ - /* * BOOTP options */ @@ -80,24 +96,32 @@ #define CONFIG_BOOTP_NTPSERVER #define CONFIG_BOOTP_TIMEOFFSET +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ /* * Command line configuration. */ #include <config_cmd_default.h> -#undef CONFIG_CMD_CONSOLE -#undef CONFIG_CMD_BDI -#undef CONFIG_CMD_LOADS -#undef CONFIG_CMD_LOADB -#undef CONFIG_CMD_CACHE +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS +#define CONFIG_CMD_SNTP /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + #if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else diff --git a/include/configs/FPS860L.h b/include/configs/FPS860L.h index f8698b5..6fec075 100644 --- a/include/configs/FPS860L.h +++ b/include/configs/FPS860L.h @@ -40,18 +40,37 @@ #define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ #undef CONFIG_8xx_CONS_NONE #define CONFIG_BAUDRATE 115200 -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else + +#define CONFIG_BOOTCOUNT_LIMIT + #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_BOOTCOMMAND "bootm 40040000" /* autoboot command */ #define CONFIG_BOARD_TYPES 1 /* support board types */ -#define CONFIG_BOOTARGS "root=/dev/nfs rw " \ - "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ - "nfsaddrs=10.0.0.99:10.0.0.2" +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "bootfile=/tftpboot/fps850L/uImage\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ @@ -79,11 +98,11 @@ #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - /* * Command line configuration. */ #include <config_cmd_default.h> + #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP @@ -95,7 +114,14 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + #if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h index 2bdcf2c..384789b 100644 --- a/include/configs/TQM823L.h +++ b/include/configs/TQM823L.h @@ -70,8 +70,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM823L/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM823M.h b/include/configs/TQM823M.h index 58bc5d3..47f416b 100644 --- a/include/configs/TQM823M.h +++ b/include/configs/TQM823M.h @@ -70,8 +70,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM823M/uImage\0" \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40180000\0" \ + "fdt_addr=40080000\0" \ + "kernel_addr=400A0000\0" \ + "ramdisk_addr=40280000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM850L.h b/include/configs/TQM850L.h index 74b16c7..e4b0bd2 100644 --- a/include/configs/TQM850L.h +++ b/include/configs/TQM850L.h @@ -66,8 +66,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM850L/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM850M.h b/include/configs/TQM850M.h index e3936c3..f26c46e 100644 --- a/include/configs/TQM850M.h +++ b/include/configs/TQM850M.h @@ -64,8 +64,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM850M/uImage\0" \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40180000\0" \ + "fdt_addr=40080000\0" \ + "kernel_addr=400A0000\0" \ + "ramdisk_addr=40280000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM855L.h b/include/configs/TQM855L.h index ae22b77..330c931 100644 --- a/include/configs/TQM855L.h +++ b/include/configs/TQM855L.h @@ -69,8 +69,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM855L/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h index 5d54f87..77c2f11 100644 --- a/include/configs/TQM855M.h +++ b/include/configs/TQM855M.h @@ -69,8 +69,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM855M/uImage\0" \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40180000\0" \ + "fdt_addr=40080000\0" \ + "kernel_addr=400A0000\0" \ + "ramdisk_addr=40280000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM860L.h b/include/configs/TQM860L.h index 40c0940..a903c2b 100644 --- a/include/configs/TQM860L.h +++ b/include/configs/TQM860L.h @@ -69,8 +69,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM860L/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h index 481e3d0..b905a0a 100644 --- a/include/configs/TQM860M.h +++ b/include/configs/TQM860M.h @@ -69,8 +69,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM860M/uImage\0" \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40180000\0" \ + "fdt_addr=40080000\0" \ + "kernel_addr=400A0000\0" \ + "ramdisk_addr=40280000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM862L.h b/include/configs/TQM862L.h index bb3b1cc..d8ddf37 100644 --- a/include/configs/TQM862L.h +++ b/include/configs/TQM862L.h @@ -72,8 +72,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM862L/uImage\0" \ - "kernel_addr=40040000\0" \ - "ramdisk_addr=40100000\0" \ + "fdt_addr=40040000\0" \ + "kernel_addr=40060000\0" \ + "ramdisk_addr=40200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM862M.h b/include/configs/TQM862M.h index d687d08..50607f0 100644 --- a/include/configs/TQM862M.h +++ b/include/configs/TQM862M.h @@ -72,8 +72,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM862M/uImage\0" \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40180000\0" \ + "fdt_addr=40080000\0" \ + "kernel_addr=400A0000\0" \ + "ramdisk_addr=40280000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h index ff00c13..ea310c4 100644 --- a/include/configs/TQM866M.h +++ b/include/configs/TQM866M.h @@ -81,8 +81,9 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_8xx\0" \ "bootfile=/tftpboot/TQM866M/uImage\0" \ - "kernel_addr=40080000\0" \ - "ramdisk_addr=40180000\0" \ + "fdt_addr=40080000\0" \ + "kernel_addr=400A0000\0" \ + "ramdisk_addr=40280000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" -- 1.5.2.4

2 2

[U-Boot-Users] [PATCH 3/3] Apollon BSP support (take #2)
by Kyungmin Park 17 Sep '07

17 Sep '07

Apollon BSP support (take #2) The Apollon based on OMAP2420 is designed for OneNAND development. It's similar with OMAP2420 H4 except some peripherals. Now this board is maintained at mainline kernel. Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> --- diff --git a/board/apollon/mem.c b/board/apollon/mem.c new file mode 100644 index 0000000..c0edca5 --- /dev/null +++ b/board/apollon/mem.c @@ -0,0 +1,235 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Derived from omap2420 + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/omap2420.h> +#include <asm/io.h> +#include <asm/arch/bits.h> +#include <asm/arch/mux.h> +#include <asm/arch/mem.h> +#include <asm/arch/clocks.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/sys_info.h> + +#include "mem.h" + +/************************************************************ + * sdelay() - simple spin loop. Will be constant time as + * its generally used in 12MHz bypass conditions only. This + * is necessary until timers are accessible. + * + * not inline to increase chances its in cache when called + *************************************************************/ +void sdelay(unsigned long loops) +{ + __asm__("1:\n" "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0"(loops)); +} + +/******************************************************************** + * prcm_init() - inits clocks for PRCM as defined in clocks.h + * (config II default). + * -- called from SRAM, or Flash (using temp SRAM stack). + ********************************************************************/ +void prcm_init(void) { } + +/************************************************************************** + * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow + * command line mem=xyz use all memory with out discontigious support + * compiled in. Could do it at the ATAG, but there really is two banks... + * Called as part of 2nd phase DDR init. + **************************************************************************/ +void make_cs1_contiguous(void) +{ + u32 size, a_add_low, a_add_high; + + size = get_sdr_cs_size(SDRC_CS0_OSET); + size /= SZ_32M; /* find size to offset CS1 */ + a_add_high = (size & 3) << 8; /* set up low field */ + a_add_low = (size & 0x3C) >> 2; /* set up high field */ + __raw_writel((a_add_high | a_add_low), SDRC_CS_CFG); + +} + +/******************************************************** + * mem_ok() - test used to see if timings are correct + * for a part. Helps in gussing which part + * we are currently using. + *******************************************************/ +u32 mem_ok(void) +{ + u32 val1, val2; + u32 pattern = 0x12345678; + + /* clear pos A */ + __raw_writel(0x0, OMAP2420_SDRC_CS0 + 0x400); + /* pattern to pos B */ + __raw_writel(pattern, OMAP2420_SDRC_CS0); + /* remove pattern off the bus */ + __raw_writel(0x0, OMAP2420_SDRC_CS0 + 4); + /* get pos A value */ + val1 = __raw_readl(OMAP2420_SDRC_CS0 + 0x400); + val2 = __raw_readl(OMAP2420_SDRC_CS0); /* get val2 */ + + /* see if pos A value changed */ + if ((val1 != 0) || (val2 != pattern)) + return (0); + else + return (1); +} + +/******************************************************** + * sdrc_init() - init the sdrc chip selects CS0 and CS1 + * - early init routines, called from flash or + * SRAM. + *******************************************************/ +void sdrc_init(void) +{ +#define EARLY_INIT 1 + /* only init up first bank here */ + do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT); +} + +/************************************************************************* + * do_sdrc_init(): initialize the SDRAM for use. + * -called from low level code with stack only. + * -code sets up SDRAM timing and muxing for 2422 or 2420. + * -optimal settings can be placed here, or redone after i2c + * inspection of board info + * + * This is a bit ugly, but should handle all memory moduels + * used with the APOLLON. The first time though this code from s_init() + * we configure the first chip select. Later on we come back and + * will configure the 2nd chip select if it exists. + * + **************************************************************************/ +void do_sdrc_init(u32 offset, u32 early) +{ +} + +/***************************************************** + * gpmc_init(): init gpmc bus + * Init GPMC for x16, MuxMode (SDRAM in x32). + * This code can only be executed from SRAM or SDRAM. + *****************************************************/ +void gpmc_init(void) +{ + u32 mux = 0, mtype, mwidth, rev, tval; + + rev = get_cpu_rev(); + if (rev == CPU_2420_2422_ES1) + tval = 1; + else + tval = 0; /* disable bit switched meaning */ + + /* global settings */ + __raw_writel(0x10, GPMC_SYSCONFIG); /* smart idle */ + __raw_writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */ + __raw_writel(tval, GPMC_TIMEOUT_CONTROL); /* timeout disable */ +#ifdef CFG_NAND_BOOT + /* set nWP, disable limited addr */ + __raw_writel(0x001, GPMC_CONFIG); +#else + /* set nWP, disable limited addr */ + __raw_writel(0x111, GPMC_CONFIG); +#endif + + /* discover bus connection from sysboot */ + if (is_gpmc_muxed() == GPMC_MUXED) + mux = BIT9; + mtype = get_gpmc0_type(); + mwidth = get_gpmc0_width(); + + /* setup cs0 */ + __raw_writel(0x0, GPMC_CONFIG7_0); /* disable current map */ + sdelay(1000); + +#ifdef CFG_NOR_BOOT + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_3, GPMC_CONFIG1_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_3, GPMC_CONFIG2_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_3, GPMC_CONFIG3_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_3, GPMC_CONFIG4_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_3, GPMC_CONFIG5_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_3, GPMC_CONFIG6_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_3, GPMC_CONFIG7_0); +#else + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_0 | mux | mtype | mwidth, + GPMC_CONFIG1_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0); +#endif + sdelay(2000); + + /* setup cs1 */ + __raw_writel(0, GPMC_CONFIG7_1); /* disable any mapping */ + sdelay(1000); + + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_1, GPMC_CONFIG1_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_1, GPMC_CONFIG2_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_1, GPMC_CONFIG3_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_1, GPMC_CONFIG4_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_1, GPMC_CONFIG5_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_1, GPMC_CONFIG6_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); + sdelay(2000); + + /* setup cs2 */ + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_0 | mux | mtype | mwidth, + GPMC_CONFIG1_2); + /* It's same as cs 0 */ + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_2); +#ifdef CFG_NOR_BOOT + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_2); +#else + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_2, GPMC_CONFIG7_2); +#endif + +#ifndef CFG_NOR_BOOT + /* setup cs3 */ + __raw_writel(0, GPMC_CONFIG7_3); /* disable any mapping */ + sdelay(1000); + + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_3, GPMC_CONFIG1_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_3, GPMC_CONFIG2_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_3, GPMC_CONFIG3_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_3, GPMC_CONFIG4_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_3, GPMC_CONFIG5_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_3, GPMC_CONFIG6_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_3, GPMC_CONFIG7_3); +#endif + +#ifndef ASYNC_NOR + __raw_writew(0xaa, (APOLLON_CS3_BASE + 0xaaa)); + __raw_writew(0x55, (APOLLON_CS3_BASE + 0x554)); + __raw_writew(0xc0, (APOLLON_CS3_BASE | SYNC_NOR_VALUE)); +#endif + sdelay(2000); +} diff --git a/board/apollon/mem.h b/board/apollon/mem.h new file mode 100644 index 0000000..5bc96fa --- /dev/null +++ b/board/apollon/mem.h @@ -0,0 +1,170 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _APOLLON_OMAP24XX_MEM_H_ +#define _APOLLON_OMAP24XX_MEM_H_ + +/* Slower full frequency range default timings for x32 operation*/ +#define APOLLON_2420_SDRC_SHARING 0x00000100 +#define APOLLON_2420_SDRC_MDCFG_0_DDR 0x00d04011 +#define APOLLON_2420_SDRC_MR_0_DDR 0x00000032 + +/* optimized timings good for current shipping parts */ +#define APOLLON_242X_SDRC_ACTIM_CTRLA_0_100MHz 0x4A59B485 +#define APOLLON_242X_SDRC_ACTIM_CTRLB_0_100MHz 0x0000000C + +#define APOLLON_242X_SDRC_ACTIM_CTRLA_0_166MHz 0x7BA35907 +#define APOLLON_242X_SDRC_ACTIM_CTRLB_0_166MHz 0x00000013 + +#define APOLLON_242X_SDRC_RFR_CTRL_100MHz 0x00030001 +#define APOLLON_242X_SDRC_RFR_CTRL_166MHz 0x00044C01 + +#define APOLLON_242x_SDRC_DLLAB_CTRL_100MHz 0x00007306 +#define APOLLON_242x_SDRC_DLLAB_CTRL_166MHz 0x00000506 + +#ifdef PRCM_CONFIG_I +#define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_166MHz +#define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_166MHz +#define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_166MHz +#define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_166MHz +#elif PRCM_CONFIG_II +#define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_100MHz +#define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_100MHz +#define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_100MHz +#define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_100MHz +#endif + +/* GPMC settings */ +#ifdef PRCM_CONFIG_I /* L3 at 165MHz */ +/* CS0: OneNAND */ +# define APOLLON_24XX_GPMC_CONFIG1_0 0x00000001 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x000c1000 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00030400 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x0b841006 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x020f0c11 +# define APOLLON_24XX_GPMC_CONFIG6_0 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_0 (0x00000e40|(APOLLON_CS0_BASE >> 24)) + +/* CS1: Ethernet */ +# define APOLLON_24XX_GPMC_CONFIG1_1 0x00011200 +# define APOLLON_24XX_GPMC_CONFIG2_1 0x001F1F01 +# define APOLLON_24XX_GPMC_CONFIG3_1 0x00080803 +# define APOLLON_24XX_GPMC_CONFIG4_1 0x1C0b1C0a +# define APOLLON_24XX_GPMC_CONFIG5_1 0x041F1F1F +# define APOLLON_24XX_GPMC_CONFIG6_1 0x000004C4 +# define APOLLON_24XX_GPMC_CONFIG7_1 (0x00000F40|(APOLLON_CS1_BASE >> 24)) + +/* CS2: OneNAND */ +/* It's same as CS0 */ +# define APOLLON_24XX_GPMC_CONFIG7_2 (0x00000e40|(APOLLON_CS2_BASE >> 24)) + +/* CS3: NOR */ +#ifdef ASYNC_NOR +# define APOLLON_24XX_GPMC_CONFIG1_3 0x00021201 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00121601 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00040401 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x12061605 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x01151317 +#else +# define SYNC_NOR_VALUE 0x24aaa +# define APOLLON_24XX_GPMC_CONFIG1_3 0xe5011211 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00090b01 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00020201 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x09030b03 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x010a0a0c +#endif /* ASYNC_NOR */ +# define APOLLON_24XX_GPMC_CONFIG6_3 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_3 (0x00000e40|(APOLLON_CS3_BASE >> 24)) +#endif /* endif PRCM_CONFIG_I */ + +#ifdef PRCM_CONFIG_II /* L3 at 100MHz */ +/* CS0: OneNAND */ +# define APOLLON_24XX_GPMC_CONFIG1_0 0x00000001 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x00081080 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00030300 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x08041004 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x020b0910 +# define APOLLON_24XX_GPMC_CONFIG6_0 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_0 (0x00000C40|(APOLLON_CS0_BASE >> 24)) + +/* CS1: ethernet */ +# define APOLLON_24XX_GPMC_CONFIG1_1 0x00401203 +# define APOLLON_24XX_GPMC_CONFIG2_1 0x001F1F01 +# define APOLLON_24XX_GPMC_CONFIG3_1 0x00080803 +# define APOLLON_24XX_GPMC_CONFIG4_1 0x1C091C09 +# define APOLLON_24XX_GPMC_CONFIG5_1 0x041F1F1F +# define APOLLON_24XX_GPMC_CONFIG6_1 0x000004C4 +# define APOLLON_24XX_GPMC_CONFIG7_1 (0x00000F40|(APOLLON_CS1_BASE >> 24)) + +/* CS2: OneNAND */ +/* It's same as CS0 */ +# define APOLLON_24XX_GPMC_CONFIG7_2 (0x00000e40|(APOLLON_CS2_BASE >> 24)) + +/* CS3: NOR */ +#define ASYNC_NOR +#ifdef ASYNC_NOR +# define APOLLON_24XX_GPMC_CONFIG1_3 0x00021201 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00121601 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00040401 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x12061605 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x01151317 +#else +# define SYNC_NOR_VALUE 0x24aaa +# define APOLLON_24XX_GPMC_CONFIG1_3 0xe1001202 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00151501 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00050501 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x0e070e07 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x01131F1F +#endif /* ASYNC_NOR */ +# define APOLLON_24XX_GPMC_CONFIG6_3 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_3 (0x00000C40|(APOLLON_CS3_BASE >> 24)) +#endif /* endif PRCM_CONFIG_II */ + +#ifdef PRCM_CONFIG_III /* L3 at 133MHz */ +# ifdef CFG_NAND_BOOT +# define APOLLON_24XX_GPMC_CONFIG1_0 0x0 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x00141400 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00141400 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x0F010F01 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x010C1414 +# define APOLLON_24XX_GPMC_CONFIG6_0 0x00000A80 +# else /* NOR boot */ +# define APOLLON_24XX_GPMC_CONFIG1_0 0x3 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x00151501 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00060602 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x10081008 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x01131F1F +# define APOLLON_24XX_GPMC_CONFIG6_0 0x000004c4 +# endif /* endif CFG_NAND_BOOT */ +# define APOLLON_24XX_GPMC_CONFIG7_0 (0x00000C40|(APOLLON_CS0_BASE >> 24)) +# define APOLLON_24XX_GPMC_CONFIG1_1 0x00011000 +# define APOLLON_24XX_GPMC_CONFIG2_1 0x001f1f01 +# define APOLLON_24XX_GPMC_CONFIG3_1 0x00080803 +# define APOLLON_24XX_GPMC_CONFIG4_1 0x1C091C09 +# define APOLLON_24XX_GPMC_CONFIG5_1 0x041f1F1F +# define APOLLON_24XX_GPMC_CONFIG6_1 0x000004C4 +# define APOLLON_24XX_GPMC_CONFIG7_1 (0x00000F40|(APOLLON_CS1_BASE >> 24)) +#endif /* endif CFG_PRCM_III */ + +#endif /* endif _APOLLON_OMAP24XX_MEM_H_ */ diff --git a/include/asm-arm/arch-arm1136/mux.h b/include/asm-arm/arch-arm1136/mux.h index 67c8419..4fdb9c6 100644 --- a/include/asm-arm/arch-arm1136/mux.h +++ b/include/asm-arm/arch-arm1136/mux.h @@ -28,6 +28,7 @@ typedef unsigned int uint32; void muxSetupSDRC(void); void muxSetupGPMC(void); void muxSetupUsb0(void); +void muxSetupUsbHost(void); void muxSetupUart3(void); void muxSetupI2C1(void); void muxSetupUART1(void); @@ -53,6 +54,10 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_GPMC_NCS0_BYTE1 ((volatile unsigned char *)0x4800008D) #define CONTROL_PADCONF_GPMC_NCS0_BYTE2 ((volatile unsigned char *)0x4800008E) #define CONTROL_PADCONF_GPMC_NCS0_BYTE3 ((volatile unsigned char *)0x4800008F) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE4 (0x48000090) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE5 (0x48000091) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE6 (0x48000092) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE7 (0x48000093) /* Pin Muxing registers used for SDRC */ #define CONTROL_PADCONF_SDRC_NCS0_BYTE0 ((volatile unsigned char *)0x480000A0) @@ -70,6 +75,7 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_SPI1_SIMO ((volatile unsigned char *)0x48000100) #define CONTROL_PADCONF_SPI1_SOMI ((volatile unsigned char *)0x48000101) #define CONTROL_PADCONF_SPI1_NCS0 ((volatile unsigned char *)0x48000102) +#define CONTROL_PADCONF_SPI1_NCS1 (0x48000103) #define CONTROL_PADCONF_MCBSP1_FSR ((volatile unsigned char *)0x4800010B) @@ -151,8 +157,20 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_USB0_SE0 ((volatile uint8 *)0x48000122) #define CONTROL_PADCONF_USB0_DAT ((volatile uint8 *)0x48000123) +/* Pin Muxing registres used for USB1. */ +#define CONTROL_PADCONF_USB1_RCV (0x480000EB) +#define CONTROL_PADCONF_USB1_TXEN (0x480000EC) + /* Pin Muxing registers used for UART3/IRDA */ #define CONTROL_PADCONF_UART3_TX_IRTX ((volatile uint8 *)0x48000118) #define CONTROL_PADCONF_UART3_RX_IRRX ((volatile uint8 *)0x48000119) +/* Pin Muxing registers used for GPIO */ +#define CONTROL_PADCONF_GPIO69 (0x480000ED) +#define CONTROL_PADCONF_GPIO70 (0x480000EE) +#define CONTROL_PADCONF_GPIO102 (0x48000116) +#define CONTROL_PADCONF_GPIO103 (0x48000117) +#define CONTROL_PADCONF_GPIO104 (0x48000118) +#define CONTROL_PADCONF_GPIO105 (0x48000119) + #endif diff --git a/include/asm-arm/arch-arm1136/omap2420.h b/include/asm-arm/arch-arm1136/omap2420.h index d833035..0c11bec 100644 --- a/include/asm-arm/arch-arm1136/omap2420.h +++ b/include/asm-arm/arch-arm1136/omap2420.h @@ -77,6 +77,20 @@ #define GPMC_CONFIG5_1 (OMAP2420_GPMC_BASE+0xA0) #define GPMC_CONFIG6_1 (OMAP2420_GPMC_BASE+0xA4) #define GPMC_CONFIG7_1 (OMAP2420_GPMC_BASE+0xA8) +#define GPMC_CONFIG1_2 (OMAP2420_GPMC_BASE+0xC0) +#define GPMC_CONFIG2_2 (OMAP2420_GPMC_BASE+0xC4) +#define GPMC_CONFIG3_2 (OMAP2420_GPMC_BASE+0xC8) +#define GPMC_CONFIG4_2 (OMAP2420_GPMC_BASE+0xCC) +#define GPMC_CONFIG5_2 (OMAP2420_GPMC_BASE+0xD0) +#define GPMC_CONFIG6_2 (OMAP2420_GPMC_BASE+0xD4) +#define GPMC_CONFIG7_2 (OMAP2420_GPMC_BASE+0xD8) +#define GPMC_CONFIG1_3 (OMAP2420_GPMC_BASE+0xF0) +#define GPMC_CONFIG2_3 (OMAP2420_GPMC_BASE+0xF4) +#define GPMC_CONFIG3_3 (OMAP2420_GPMC_BASE+0xF8) +#define GPMC_CONFIG4_3 (OMAP2420_GPMC_BASE+0xFC) +#define GPMC_CONFIG5_3 (OMAP2420_GPMC_BASE+0x100) +#define GPMC_CONFIG6_3 (OMAP2420_GPMC_BASE+0x104) +#define GPMC_CONFIG7_3 (OMAP2420_GPMC_BASE+0x108) /* SMS */ #define OMAP2420_SMS_BASE 0x68008000 @@ -209,13 +223,24 @@ #define SRAM_OFFSET2 0x0000F800 #define SRAM_VECT_CODE (SRAM_OFFSET0|SRAM_OFFSET1|SRAM_OFFSET2) -#define LOW_LEVEL_SRAM_STACK 0x4020FFFC - -#define PERIFERAL_PORT_BASE 0x480FE003 - /* FPGA on Debug board.*/ #define ETH_CONTROL_REG (H4_CS1_BASE+0x30b) #define LAN_RESET_REGISTER (H4_CS1_BASE+0x1c) #endif /* endif CONFIG_2420H4 */ +#if defined(CONFIG_APOLLON) +#define APOLLON_CS0_BASE 0x00000000 /* OneNAND */ +#define APOLLON_CS1_BASE 0x08000000 /* ethernet */ +#define APOLLON_CS2_BASE 0x10000000 /* OneNAND */ +#define APOLLON_CS3_BASE 0x18000000 /* NOR */ + +#define ETH_CONTROL_REG (APOLLON_CS1_BASE + 0x30b) +#define LAN_RESET_REGISTER (APOLLON_CS1_BASE + 0x1c) +#endif /* endif CONFIG_APOLLON */ + +/* Common */ +#define LOW_LEVEL_SRAM_STACK 0x4020FFFC + +#define PERIFERAL_PORT_BASE 0x480FE003 + #endif diff --git a/include/asm-arm/mach-types.h b/include/asm-arm/mach-types.h index f6a5b4f..ab19047 100644 --- a/include/asm-arm/mach-types.h +++ b/include/asm-arm/mach-types.h @@ -737,6 +737,7 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_CB3RUFC 726 #define MACH_TYPE_MP2USB 727 #define MACH_TYPE_AT91SAM9261EK 848 +#define MACH_TYPE_OMAP_APOLLON 919 #define MACH_TYPE_PDNB3 1002 #define MACH_TYPE_AT91SAM9260EK 1099 #define MACH_TYPE_AT91RM9200DF 1119 @@ -6826,6 +6827,18 @@ extern unsigned int __machine_arch_type; # define machine_is_omap_h4() (0) #endif +#ifdef CONFIG_MACH_OMAP_APOLLON +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_OMAP_APOLLON +# endif +# define machine_is_omap_apollon() (machine_arch_type == MACH_TYPE_OMAP_APOLLON) +#else +# define machine_is_omap_apollon() (0) +#endif + #ifdef CONFIG_MACH_N10 # ifdef machine_arch_type # undef machine_arch_type diff --git a/include/configs/apollon.h b/include/configs/apollon.h new file mode 100644 index 0000000..49fd234 --- /dev/null +++ b/include/configs/apollon.h @@ -0,0 +1,250 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Configuration settings for the 2420 Samsung Apollon board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP2420 1 /* which is in a 2420 */ +#define CONFIG_OMAP2420_APOLLON 1 +#define CONFIG_APOLLON 1 +#define CONFIG_APOLLON_PLUS 1 /* If you have apollon plus 1.x */ + +/* Clock config to target*/ +#define PRCM_CONFIG_I 1 +/* #define PRCM_CONFIG_II 1 */ + +/* Boot method */ +/* uncomment if you use NOR boot */ +/* #define CFG_NOR_BOOT 1 */ + +/* uncommnet if you use NOR on CS3 */ +/* #define CFG_USE_NOR 1 */ + +#ifdef CFG_NOR_BOOT +#undef CFG_USE_NOR +#define CFG_USE_NOR 1 +#endif + +#include <asm/arch/omap2420.h> /* get chip and board defs */ + +#define V_SCLK 12000000 + +/* input clock of PLL */ +/* the OMAP2420 H4 has 12MHz, 13MHz, or 19.2Mhz crystal input */ +#define CONFIG_SYS_CLK_FREQ V_SCLK + +#undef CONFIG_USE_IRQ /* no support for IRQs */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 +#define CONFIG_REVISION_TAG 1 + +/* + * Size of malloc() pool + */ +/* Total Size of Environment Sector */ +#define CFG_ENV_SIZE SZ_128K +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + SZ_128K) +/* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_SIZE 128 + +/* + * Hardware drivers + */ + +/* + * SMC91c96 Etherent + */ +#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_LAN91C96_BASE (APOLLON_CS1_BASE+0x300) +#define CONFIG_LAN91C96_EXT_PHY + +/* + * NS16550 Configuration + */ +#define V_NS16550_CLK (48000000) /* 48MHz (APLL96/2) */ + +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE (-4) +#define CFG_NS16550_CLK V_NS16550_CLK /* 3MHz (1.5MHz*2) */ +#define CFG_NS16550_COM1 OMAP2420_UART1 + +/* + * select serial console configuration + */ +#define CONFIG_SERIAL1 1 /* UART1 on H4 */ + + /* + * I2C configuration + */ +#define CONFIG_HARD_I2C +#define CFG_I2C_SPEED 100000 +#define CFG_I2C_SLAVE 1 +#define CONFIG_DRIVER_OMAP24XX_I2C + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_ONENAND + +#undef CONFIG_CMD_AUTOSCRIPT + +#ifndef CFG_USE_NOR +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#endif + +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT + +#define CONFIG_BOOTDELAY 1 + +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 192.168.116.25 +#define CONFIG_SERVERIP 192.168.116.1 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_ETHADDR 00:0E:99:00:24:20 +#ifdef CONFIG_APOLLON_PLUS +#define CONFIG_MEMSIZE "64M" +#else +#define CONFIG_MEMSIZE "128M" +#endif + +#define CONFIG_BOOTARGS "root=/dev/nfs rw" \ + " mem=" CONFIG_MEMSIZE " console=ttyS0,115200n8" \ + " ip=192.168.116.25:192.168.116.1::255.255.255.0:" \ + "apollon:eth0:off nfsroot=/tftpboot/nfsroot" \ + " profile=2" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "Image=tftp 0x80008000 Image; go 0x80008000\0" \ + "zImage=tftp 0x80180000 zImage; go 0x80180000\0" \ + "uImage=tftp 0x80180000 uImage; bootm 0x80180000\0" \ + "uboot=tftp 0x80008000 u-boot.bin; go 0x80008000\0" \ + "xloader=tftp 0x80180000 x-load.bin;" \ + "cp.w 0x80180000 0x00000400 0x1000; go 0x00000400\0" \ + "syncmode50=mw.w 0x1e442 0xc0c4; mw 0x6800a060 0xe30d1201\0" \ + "syncmode=mw.w 0x1e442 0xe0f4; mw 0x6800a060 0xe30d1201\0" \ + "norboot=cp32 0x18040000 0x80008000 0x200000; " \ + "go 0x80008000\0" \ + "oneboot=onenand read 0x80008000 0x40000 0x200000; " \ + "go 0x80008000\0" \ + "onesyncboot=run syncmode oneboot\0" \ + "rootpath=/tftpboot/nfsroot\0" \ + "bootcmd=run uboot\0" + +/* + * Miscellaneous configurable options + */ +#define V_PROMPT "Apollon # " + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT V_PROMPT +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START (OMAP2420_SDRC_CS0) /* memtest works on */ +#define CFG_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M) + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */ + +/* The 2420 has 12 GP timers, + * they can be driven by the SysClk (12/13/19.2) or by + * 32KHz clk, or from external sig. This rate is divided by a local divisor. + */ +#define V_PVT 7 /* use with 12MHz/128 */ + +#define CFG_TIMERBASE OMAP2420_GPT2 +#define CFG_PVT V_PVT /* 2^(pvt+1) */ +#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT)) + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE SZ_128K /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */ +#endif + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +/* CS1 may or may not be populated */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 OMAP2420_SDRC_CS0 +#define PHYS_SDRAM_1_SIZE SZ_128M +#define PHYS_SDRAM_2 OMAP2420_SDRC_CS1 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#ifdef CFG_USE_NOR +/* OneNAND boot, NOR has CS3, But NOR has CS0 when NOR boot */ +#define CFG_FLASH_BASE 0x18000000 +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_MAX_FLASH_SECT 1024 +/*----------------------------------------------------------------------- + + * CFI FLASH driver setup + */ +#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ +#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */ + +#else /* !CFG_USE_NOR */ + +#define CFG_NO_FLASH 1 +#endif /* CFG_USE_NOR */ + +/* OneNAND boot, OneNAND has CS0, NOR boot ONeNAND has CS2 */ +#define CFG_ONENAND_BASE 0x00000000 +#define CFG_ENV_IS_IN_ONENAND 1 +#define CFG_ENV_ADDR 0x00020000 + +#endif /* __CONFIG_H */

1 0

[U-Boot-Users] [PATCH 2/3] Apollon BSP support (take #2)
by Kyungmin Park 17 Sep '07

17 Sep '07

Apollon BSP support (take #2) The Apollon based on OMAP2420 is designed for OneNAND development. It's similar with OMAP2420 H4 except some peripherals. Now this board is maintained at mainline kernel. Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> --- diff --git a/board/apollon/lowlevel_init.S b/board/apollon/lowlevel_init.S new file mode 100644 index 0000000..fbc6df2 --- /dev/null +++ b/board/apollon/lowlevel_init.S @@ -0,0 +1,340 @@ +/* + * Board specific setup info + * + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <version.h> +#include <asm/arch/omap2420.h> +#include <asm/arch/mem.h> +#include <asm/arch/clocks.h> +#include "mem.h" + +#define APOLLON_CS0_BASE 0x00000000 + +#ifdef PRCM_CONFIG_I +#define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 +#define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 +#define SDRC_RFR_CTRL_0_VAL 0x00044C01 +#elif defined(PRCM_CONFIG_II) +#define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 +#define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C +#define SDRC_RFR_CTRL_0_VAL 0x00030001 +#endif + +#define SDRAM_BASE_ADDRESS 0x80008000 + +_TEXT_BASE: + .word TEXT_BASE /* sdram load addr from config.mk */ + +.globl lowlevel_init +lowlevel_init: + +#ifdef CFG_NOR_BOOT + /* Check running in SDRAM */ + mov r0, pc, lsr #28 + cmp r0, #8 + beq prcm_setup + +flash_setup: + /* In Flash */ + ldr r0, =WD2_BASE + ldr r1, =WD_UNLOCK1 + str r1, [r0, #WSPR] + + ldr r1, =WD_UNLOCK2 + str r1, [r0, #WSPR] + + /* Pin muxing for SDRC */ + mov r1, #0x00 + ldr r0, =0x480000A1 /* ball C12, mode 0 */ + strb r1, [r0] + + ldr r0, =0x48000032 /* ball D11, mode 0 */ + strb r1, [r0] + + ldr r0, =0x480000A3 /* ball B13, mode 0 */ + strb r1, [r0] + + /* SDRC setting */ + ldr r0, =OMAP2420_SDRC_BASE + ldr r1, =0x00000010 + str r1, [r0, #0x10] + + ldr r1, =0x00000100 + str r1, [r0, #0x44] + + /* SDRC CS0 configuration */ + ldr r1, =0x00d04011 + str r1, [r0, #0x80] + + ldr r1, =SDRC_ACTIM_CTRLA_0_VAL + str r1, [r0, #0x9C] + + ldr r1, =SDRC_ACTIM_CTRLB_0_VAL + str r1, [r0, #0xA0] + + ldr r1, =SDRC_RFR_CTRL_0_VAL + str r1, [r0, #0xA4] + + ldr r1, =0x00000041 + str r1, [r0, #0x70] + + /* Manual command sequence */ + ldr r1, =0x00000007 + str r1, [r0, #0xA8] + + ldr r1, =0x00000000 + str r1, [r0, #0xA8] + + ldr r1, =0x00000001 + str r1, [r0, #0xA8] + + ldr r1, =0x00000002 + str r1, [r0, #0xA8] + str r1, [r0, #0xA8] + + /* + * CS0 SDRC Mode register + * Burst length = 4 - DDR memory + * Serial mode + * CAS latency = 3 + */ + ldr r1, =0x00000032 + str r1, [r0, #0x84] + + /* Note: You MUST set EMR values */ + /* EMR1 & EMR2 */ + ldr r1, =0x00000000 + str r1, [r0, #0x88] + str r1, [r0, #0x8C] + +#ifdef OLD_SDRC_DLLA_CTRL + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00007306 + str r1, [r0, #0x60] + + ldr r1, =0x00007303 + str r1, [r0, #0x60] +#else + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x60] + + ldr r1, =0x00000503 + str r1, [r0, #0x60] +#endif + +#ifdef __BROKEN_FEATURE__ + /* SDRC_DLLB_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x68] + + ldr r1, =0x00000503 + str r1, [r0, #0x68] +#endif + + /* little delay after init */ + mov r2, #0x1800 +1: + subs r2, r2, #0x1 + bne 1b + + /* Setup base address */ + ldr r0, =0x00000000 /* NOR address */ + ldr r1, =SDRAM_BASE_ADDRESS /* SDRAM address */ + ldr r2, =0x20000 /* Size: 128KB */ + +copy_loop: + ldmia r0!, {r3-r10} + stmia r1!, {r3-r10} + cmp r0, r2 + ble copy_loop + + ldr r1, =SDRAM_BASE_ADDRESS + mov lr, pc + mov pc, r1 +#endif + +prcm_setup: + ldr r0, =OMAP2420_CM_BASE + ldr r1, [r0, #0x544] /* CLKSEL2_PLL */ + bic r1, r1, #0x03 + orr r1, r1, #0x02 + str r1, [r0, #0x544] + + ldr r1, [r0, #0x500] + bic r1, r1, #0x03 + orr r1, r1, #0x01 + str r1, [r0, #0x500] + + ldr r1, [r0, #0x140] + bic r1, r1, #0x1f + orr r1, r1, #0x02 + str r1, [r0, #0x140] + +#ifdef PRCM_CONFIG_I + ldr r1, =0x000003C3 +#else + ldr r1, =0x00000343 +#endif + str r1, [r0, #0x840] + + ldr r1, =0x00000002 + str r1, [r0, #0x340] + + ldr r1, =CM_CLKSEL1_CORE +#ifdef PRCM_CONFIG_I + ldr r2, =0x08300C44 +#else + ldr r2, =0x04600C26 +#endif + str r2, [r1] + + ldr r0, =OMAP2420_CM_BASE + ldr r1, [r0, #0x084] + and r1, r1, #0x01 + cmp r1, #0x01 + bne clkvalid + + b . + +clkvalid: + mov r1, #0x01 + str r1, [r0, #0x080] + +waitvalid: + ldr r1, [r0, #0x084] + and r1, r1, #0x01 + cmp r1, #0x00 + bne waitvalid + + ldr r0, =CM_CLKSEL1_PLL +#ifdef PRCM_CONFIG_I + ldr r1, =0x01837100 +#else + ldr r1, =0x01832100 +#endif + str r1, [r0] + + ldr r0, =PRCM_CLKCFG_CTRL + mov r1, #0x01 + str r1, [r0] + mov r6, #0x50 +loop1: + subs r6, r6, #0x01 + cmp r6, #0x01 + bne loop1 + + ldr r0, =CM_CLKEN_PLL + mov r1, #0x0f + str r1, [r0] + + mov r6, #0x100 +loop2: + subs r6, r6, #0x01 + cmp r6, #0x01 + bne loop2 + + ldr r0, =0x48008200 + ldr r1, =0xbfffffff + str r1, [r0] + + ldr r0, =0x48008210 + ldr r1, =0xfffffff9 + str r1, [r0] + +#if 1 + ldr r0, =0x4806a004 + ldr r1, =0x00 + strb r1, [r0] + + ldr r0, =0x4806a020 + ldr r1, =0x07 + strb r1, [r0] + + ldr r0, =0x4806a00c + ldr r1, =0x83 + strb r1, [r0] + + ldr r0, =0x4806a000 + ldr r1, =0x1a + strb r1, [r0] + + ldr r0, =0x4806a004 + ldr r1, =0x00 + strb r1, [r0] + + ldr r0, =0x4806a00c + ldr r1, =0x03 + strb r1, [r0] + + ldr r0, =0x4806a010 + ldr r1, =0x03 + strb r1, [r0] + + ldr r0, =0x4806a008 + ldr r1, =0x04 + strb r1, [r0] + + ldr r0, =0x4806a020 + ldr r1, =0x00 + strb r1, [r0] + +#if 0 + ldr r0, =0x4806a000 + mov r1, #'u' + strb r1, [r0] +#endif + +#if 0 + /* LED0 OFF */ + ldr r3, =0x480000E5 + mov r4, #0x0b + strb r4, [r3] +#endif + +#endif + + ldr sp, SRAM_STACK + str ip, [sp] /* stash old link register */ + mov ip, lr /* save link reg across call */ + bl s_init /* go setup pll,mux,memory */ + ldr ip, [sp] /* restore save ip */ + mov lr, ip /* restore link reg */ + + /* map interrupt controller */ + ldr r0, VAL_INTH_SETUP + mcr p15, 0, r0, c15, c2, 4 + + /* back to arch calling code */ + mov pc, lr + + /* the literal pools origin */ + .ltorg + +VAL_INTH_SETUP: + .word PERIFERAL_PORT_BASE +SRAM_STACK: + .word LOW_LEVEL_SRAM_STACK diff --git a/board/apollon/sys_info.c b/board/apollon/sys_info.c new file mode 100644 index 0000000..26ac9a2 --- /dev/null +++ b/board/apollon/sys_info.c @@ -0,0 +1,403 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Derived from omap2420 + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/omap2420.h> +#include <asm/io.h> +#include <asm/arch/bits.h> +#include <asm/arch/mem.h> /* get mem tables */ +#include <asm/arch/sys_proto.h> +#include <asm/arch/sys_info.h> +#include <i2c.h> + +/************************************************************************** + * get_prod_id() - get id info from chips + ***************************************************************************/ +static u32 get_prod_id(void) +{ + u32 p; + p = __raw_readl(PRODUCTION_ID); /* get production ID */ + return ((p & CPU_242X_PID_MASK) >> 16); +} + +/************************************************************************** + * get_cpu_type() - low level get cpu type + * - no C globals yet. + * - just looking to say if this is a 2422 or 2420 or ... + * - to start with we will look at switch settings.. + * - 2422 id's same as 2420 for ES1 will rely on H4 board characteristics + * (mux for 2420, non-mux for 2422). + ***************************************************************************/ +u32 get_cpu_type(void) +{ + u32 v; + + switch (get_prod_id()) { + case 1:; /* 2420 */ + case 2: + return (CPU_2420); + break; /* 2420 pop */ + case 4: + return (CPU_2422); + break; + case 8: + return (CPU_2423); + break; + default: + break; /* early 2420/2422's unmarked */ + } + + v = __raw_readl(TAP_IDCODE_REG); + v &= CPU_24XX_ID_MASK; + /* currently 2420 and 2422 have same id */ + if (v == CPU_2420_CHIPID) { + if (is_gpmc_muxed() == GPMC_MUXED) /* if mux'ed */ + return (CPU_2420); + else + return (CPU_2422); + } else + return (CPU_2420); /* don't know, say 2420 */ +} + +/****************************************** + * get_cpu_rev(void) - extract version info + ******************************************/ +u32 get_cpu_rev(void) +{ + u32 v; + v = __raw_readl(TAP_IDCODE_REG); + v = v >> 28; + return (v + 1); /* currently 2422 and 2420 match up */ +} + +/**************************************************** + * is_mem_sdr() - return 1 if mem type in use is SDR + ****************************************************/ +u32 is_mem_sdr(void) +{ + volatile u32 *burst = (volatile u32 *)(SDRC_MR_0 + SDRC_CS0_OSET); + if (*burst == H4_2420_SDRC_MR_0_SDR) + return (1); + return (0); +} + +/*********************************************************** + * get_mem_type() - identify type of mDDR part used. + * 2422 uses stacked DDR, 2 parts CS0/CS1. + * 2420 may have 1 or 2, no good way to know...only init 1... + * when eeprom data is up we can select 1 more. + *************************************************************/ +u32 get_mem_type(void) +{ + u32 cpu, sdr = is_mem_sdr(); + + cpu = get_cpu_type(); + if (cpu == CPU_2422 || cpu == CPU_2423) + return (DDR_STACKED); + + if (get_prod_id() == 0x2) + return (XDR_POP); + + if (get_board_type() == BOARD_H4_MENELAUS) + if (sdr) + return (SDR_DISCRETE); + else + return (DDR_COMBO); + else if (sdr) /* SDP + SDR kit */ + return (SDR_DISCRETE); + else + return (DDR_DISCRETE); /* origional SDP */ +} + +/*********************************************************************** + * get_cs0_size() - get size of chip select 0/1 + ************************************************************************/ +u32 get_sdr_cs_size(u32 offset) +{ + u32 size; + size = __raw_readl(SDRC_MCFG_0 + offset) >> 8; /* get ram size field */ + size &= 0x2FF; /* remove unwanted bits */ + size *= SZ_2M; /* find size in MB */ + return (size); +} + +/*********************************************************************** + * get_board_type() - get board type based on current production stats. + * --- NOTE: 2 I2C EEPROMs will someday be populated with proper info. + * when they are available we can get info from there. This should + * be correct of all known boards up until today. + ************************************************************************/ +u32 get_board_type(void) +{ + return (BOARD_H4_SDP); +} + +/****************************************************************** + * get_sysboot_value() - get init word settings (dip switch on h4) + ******************************************************************/ +inline u32 get_sysboot_value(void) +{ + return (0x00000FFF & __raw_readl(CONTROL_STATUS)); +} + +/*************************************************************************** + * get_gpmc0_base() - Return current address hardware will be + * fetching from. The below effectively gives what is correct, its a bit + * mis-leading compared to the TRM. For the most general case the mask + * needs to be also taken into account this does work in practice. + * - for u-boot we currently map: + * -- 0 to nothing, + * -- 4 to flash + * -- 8 to enent + * -- c to wifi + ****************************************************************************/ +u32 get_gpmc0_base(void) +{ + u32 b; + + b = __raw_readl(GPMC_CONFIG7_0); + b &= 0x1F; /* keep base [5:0] */ + b = b << 24; /* ret 0x0b000000 */ + return (b); +} + +/***************************************************************** + * is_gpmc_muxed() - tells if address/data lines are multiplexed + *****************************************************************/ +u32 is_gpmc_muxed(void) +{ + u32 mux; + mux = get_sysboot_value(); + if ((mux & (BIT0 | BIT1 | BIT2 | BIT3)) == (BIT0 | BIT2 | BIT3)) + return (GPMC_MUXED); /* NAND Boot mode */ + if (mux & BIT1) /* if mux'ed */ + return (GPMC_MUXED); + else + return (GPMC_NONMUXED); +} + +/************************************************************************ + * get_gpmc0_type() - read sysboot lines to see type of memory attached + ************************************************************************/ +u32 get_gpmc0_type(void) +{ + u32 type; + type = get_sysboot_value(); + if ((type & (BIT3 | BIT2)) == (BIT3 | BIT2)) + return (TYPE_NAND); + else + return (TYPE_NOR); +} + +/******************************************************************* + * get_gpmc0_width() - See if bus is in x8 or x16 (mainly for nand) + *******************************************************************/ +u32 get_gpmc0_width(void) +{ + u32 width; + width = get_sysboot_value(); + if ((width & 0xF) == (BIT3 | BIT2)) + return (WIDTH_8BIT); + else + return (WIDTH_16BIT); +} + +/********************************************************************* + * wait_on_value() - common routine to allow waiting for changes in + * volatile regs. + *********************************************************************/ +u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound) +{ + u32 i = 0, val; + do { + ++i; + val = __raw_readl(read_addr) & read_bit_mask; + if (val == match_value) + return (1); + if (i == bound) + return (0); + } while (1); +} + +/********************************************************************* + * display_board_info() - print banner with board info. + *********************************************************************/ +void display_board_info(u32 btype) +{ + char cpu_2420[] = "2420"; /* cpu type */ + char cpu_2422[] = "2422"; + char cpu_2423[] = "2423"; + char db_men[] = "Menelaus"; /* board type */ + char db_ip[] = "IP"; + char mem_sdr[] = "mSDR"; /* memory type */ + char mem_ddr[] = "mDDR"; + char t_tst[] = "TST"; /* security level */ + char t_emu[] = "EMU"; + char t_hs[] = "HS"; + char t_gp[] = "GP"; + char unk[] = "?"; + + char *cpu_s, *db_s, *mem_s, *sec_s; + u32 cpu, rev, sec; + + rev = get_cpu_rev(); + cpu = get_cpu_type(); + sec = get_device_type(); + + if (is_mem_sdr()) + mem_s = mem_sdr; + else + mem_s = mem_ddr; + + if (cpu == CPU_2423) + cpu_s = cpu_2423; + else if (cpu == CPU_2422) + cpu_s = cpu_2422; + else + cpu_s = cpu_2420; + + if (btype == BOARD_H4_MENELAUS) + db_s = db_men; + else + db_s = db_ip; + + switch (sec) { + case TST_DEVICE: + sec_s = t_tst; + break; + case EMU_DEVICE: + sec_s = t_emu; + break; + case HS_DEVICE: + sec_s = t_hs; + break; + case GP_DEVICE: + sec_s = t_gp; + break; + default: + sec_s = unk; + } + + printf("OMAP%s-%s revision %d\n", cpu_s, sec_s, rev - 1); + printf("Samsung Apollon SDP Base Board + %s \n", mem_s); +} + +/************************************************************************* + * get_board_rev() - setup to pass kernel board revision information + * 0 = 242x IP platform (first 2xx boards) + * 1 = 242x Menelaus platfrom. + *************************************************************************/ +u32 get_board_rev(void) +{ + u32 rev = 0; + u32 btype = get_board_type(); + + if (btype == BOARD_H4_MENELAUS) + rev = 1; + return (rev); +} + +/******************************************************** + * get_base(); get upper addr of current execution + *******************************************************/ +u32 get_base(void) +{ + u32 val; + __asm__ __volatile__("mov %0, pc \n":"=r"(val)::"memory"); + val &= 0xF0000000; + val >>= 28; + return (val); +} + +/******************************************************** + * get_base2(); get 2upper addr of current execution + *******************************************************/ +u32 get_base2(void) +{ + u32 val; + __asm__ __volatile__("mov %0, pc \n":"=r"(val)::"memory"); + val &= 0xFF000000; + val >>= 24; + return (val); +} + +/******************************************************** + * running_in_flash() - tell if currently running in + * flash. + *******************************************************/ +u32 running_in_flash(void) +{ + if (get_base() < 4) + return (1); /* in flash */ + return (0); /* running in SRAM or SDRAM */ +} + +/******************************************************** + * running_in_sram() - tell if currently running in + * sram. + *******************************************************/ +u32 running_in_sram(void) +{ + if (get_base() == 4) + return (1); /* in SRAM */ + return (0); /* running in FLASH or SDRAM */ +} + +/******************************************************** + * running_in_sdram() - tell if currently running in + * flash. + *******************************************************/ +u32 running_in_sdram(void) +{ + if (get_base() > 4) + return (1); /* in sdram */ + return (0); /* running in SRAM or FLASH */ +} + +/************************************************************* + * running_from_internal_boot() - am I a signed NOR image. + *************************************************************/ +u32 running_from_internal_boot(void) +{ + u32 v, base; + + v = get_sysboot_value() & BIT3; + base = get_base2(); + /* if running at mask rom flash address and + * sysboot3 says this was an internal boot + */ + if ((base == 0x08) && v) + return (1); + else + return (0); +} + +/************************************************************* + * get_device_type(): tell if GP/HS/EMU/TST + *************************************************************/ +u32 get_device_type(void) +{ + int mode; + mode = __raw_readl(CONTROL_STATUS) & (BIT10 | BIT9 | BIT8); + return (mode >>= 8); +} diff --git a/board/apollon/u-boot.lds b/board/apollon/u-boot.lds new file mode 100644 index 0000000..5f2b5cd --- /dev/null +++ b/board/apollon/u-boot.lds @@ -0,0 +1,63 @@ +/* + * + * Copyright (C) 2005-2007 Samsung Elecronics + * Kyungin Park <kyugnmin.park(a)samsung.com> + * + * January 2004 - Changed to support H4 device + * Copyright (c) 2004 Texas Instruments + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, <gj(a)denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/arm1136/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +}

1 0

[U-Boot-Users] [PATCH 1/3] Apollon BSP support (take #2)
by Kyungmin Park 17 Sep '07

17 Sep '07

Apollon BSP support (take #2) The Apollon based on OMAP2420 is designed for OneNAND development. It's similar with OMAP2420 H4 except some peripherals. Now this board is maintained at mainline kernel. Signed-off-by: Kyungmin Park <kyungmin.park(a)samsung.com> --- diff --git a/Makefile b/Makefile index c35f022..d680ad0 100644 --- a/Makefile +++ b/Makefile @@ -2356,9 +2356,12 @@ zylonite_config : ######################################################################### ## ARM1136 Systems ######################################################################### -omap2420h4_config : unconfig +omap2420h4_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 +apollon_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm1136 apollon + #======================================================================== # i386 #======================================================================== diff --git a/board/apollon/Makefile b/board/apollon/Makefile new file mode 100644 index 0000000..91605ca --- /dev/null +++ b/board/apollon/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := apollon.o mem.o sys_info.o +SOBJS := lowlevel_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/apollon/apollon.c b/board/apollon/apollon.c new file mode 100644 index 0000000..064d143 --- /dev/null +++ b/board/apollon/apollon.c @@ -0,0 +1,472 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics. + * Kyungmin Park <kyungmin.park(a)samsung.com> + * + * Derived from omap2420 + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <asm/arch/omap2420.h> +#include <asm/io.h> +#include <asm/arch/bits.h> +#include <asm/arch/mux.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/sys_info.h> +#include <asm/arch/mem.h> +#include <asm/mach-types.h> + +void wait_for_command_complete(unsigned int wd_base); + +DECLARE_GLOBAL_DATA_PTR; + +#define write_config_reg(reg, value) \ +do { \ + writeb(value, reg); \ +} while (0) + +#define mask_config_reg(reg, mask) \ +do { \ + char value = readb(reg) & ~(mask); \ + writeb(value, reg); \ +} while (0) + +/******************************************************* + * Routine: delay + * Description: spinning delay to use before udelay works + ******************************************************/ +static inline void delay(unsigned long loops) +{ + __asm__("1:\n" "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0"(loops)); +} + +/***************************************** + * Routine: board_init + * Description: Early hardware init. + *****************************************/ +int board_init(void) +{ + gpmc_init(); /* in SRAM or SDRM, finish GPMC */ + + gd->bd->bi_arch_number = 919; + /* adress of boot parameters */ + gd->bd->bi_boot_params = (OMAP2420_SDRC_CS0 + 0x100); + + return 0; +} + +/********************************************************** + * Routine: s_init + * Description: Does early system init of muxing and clocks. + * - Called path is with sram stack. + **********************************************************/ +void s_init(void) +{ + watchdog_init(); + set_muxconf_regs(); + delay(100); + + peripheral_enable(); + icache_enable(); +} + +/******************************************************* + * Routine: misc_init_r + * Description: Init ethernet (done here so udelay works) + ********************************************************/ +int misc_init_r(void) +{ + ether_init(); /* better done here so timers are init'ed */ + return (0); +} + +/**************************************** + * Routine: watchdog_init + * Description: Shut down watch dogs + *****************************************/ +void watchdog_init(void) +{ + /* There are 4 watch dogs. 1 secure, and 3 general purpose. + * The ROM takes care of the secure one. Of the 3 GP ones, + * 1 can reset us directly, the other 2 only generate MPU interrupts. + */ + __raw_writel(WD_UNLOCK1, WD2_BASE + WSPR); + wait_for_command_complete(WD2_BASE); + __raw_writel(WD_UNLOCK2, WD2_BASE + WSPR); + +#define MPU_WD_CLOCKED 1 +#if MPU_WD_CLOCKED + /* value 0x10 stick on aptix, BIT4 polarity seems oppsite */ + __raw_writel(WD_UNLOCK1, WD3_BASE + WSPR); + wait_for_command_complete(WD3_BASE); + __raw_writel(WD_UNLOCK2, WD3_BASE + WSPR); + + __raw_writel(WD_UNLOCK1, WD4_BASE + WSPR); + wait_for_command_complete(WD4_BASE); + __raw_writel(WD_UNLOCK2, WD4_BASE + WSPR); +#endif +} + +/****************************************************** + * Routine: wait_for_command_complete + * Description: Wait for posting to finish on watchdog + ******************************************************/ +void wait_for_command_complete(unsigned int wd_base) +{ + int pending = 1; + do { + pending = __raw_readl(wd_base + WWPS); + } while (pending); +} + +/******************************************************************* + * Routine:ether_init + * Description: take the Ethernet controller out of reset and wait + * for the EEPROM load to complete. + ******************************************************************/ +void ether_init(void) +{ +#ifdef CONFIG_DRIVER_LAN91C96 + int cnt = 20; + + __raw_writeb(0x03, OMAP2420_CTRL_BASE + 0x0f2); /*protect->gpio74 */ + + __raw_writew(0x0, LAN_RESET_REGISTER); + do { + __raw_writew(0x1, LAN_RESET_REGISTER); + udelay(100); + if (cnt == 0) { + printf("1. eth reset err\n"); + goto eth_reset_err_out; + } + --cnt; + } while (__raw_readw(LAN_RESET_REGISTER) != 0x1); + + cnt = 20; + + do { + __raw_writew(0x0, LAN_RESET_REGISTER); + udelay(100); + if (cnt == 0) { + printf("2. eth reset err\n"); + goto eth_reset_err_out; + } + --cnt; + } while (__raw_readw(LAN_RESET_REGISTER) != 0x0000); + udelay(1000); + + mask_config_reg(ETH_CONTROL_REG, 0x01); + udelay(1000); + +eth_reset_err_out: + return; +#endif +} + +/********************************************** + * Routine: dram_init + * Description: sets uboots idea of sdram size + **********************************************/ +int dram_init(void) +{ + unsigned int size0 = 0, size1 = 0; + u32 mtype, btype, rev = 0, cpu = 0; +#define NOT_EARLY 0 + + btype = get_board_type(); + mtype = get_mem_type(); + rev = get_cpu_rev(); + cpu = get_cpu_type(); + + display_board_info(btype); + + if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) { + /* init other chip select */ + do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); + } + + size0 = get_sdr_cs_size(SDRC_CS0_OSET); + size1 = get_sdr_cs_size(SDRC_CS1_OSET); + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = size0; +#if CONFIG_NR_DRAM_BANKS > 1 + gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + size0; + gd->bd->bi_dram[1].size = size1; +#endif + + return 0; +} + +/********************************************************** + * Routine: set_muxconf_regs + * Description: Setting up the configuration Mux registers + * specific to the hardware + *********************************************************/ +void set_muxconf_regs(void) +{ + muxSetupSDRC(); + muxSetupGPMC(); + muxSetupUsb0(); /* USB Device */ + muxSetupUsbHost(); /* USB Host */ + muxSetupUART1(); + muxSetupLCD(); + muxSetupMMCSD(); + muxSetupTouchScreen(); +} + +/***************************************************************** + * Routine: peripheral_enable + * Description: Enable the clks & power for perifs (GPT2, UART1,...) + ******************************************************************/ +void peripheral_enable(void) +{ + unsigned int v, if_clks = 0, func_clks = 0; + + /* Enable GP2 timer. */ + if_clks |= BIT4 | BIT3; + func_clks |= BIT4 | BIT3; + /* Sys_clk input OMAP2420_GPT2 */ + v = __raw_readl(CM_CLKSEL2_CORE) | 0x4 | 0x2; + __raw_writel(v, CM_CLKSEL2_CORE); + __raw_writel(0x1, CM_CLKSEL_WKUP); + +#ifdef CFG_NS16550 + /* Enable UART1 clock */ + func_clks |= BIT21; + if_clks |= BIT21; +#endif + /* Interface clocks on */ + v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; + __raw_writel(v, CM_ICLKEN1_CORE); + /* Functional Clocks on */ + v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; + __raw_writel(v, CM_FCLKEN1_CORE); + delay(1000); + +#ifndef KERNEL_UPDATED + { +#define V1 0xffffffff +#define V2 0x00000007 + + __raw_writel(V1, CM_FCLKEN1_CORE); + __raw_writel(V2, CM_FCLKEN2_CORE); + __raw_writel(V1, CM_ICLKEN1_CORE); + __raw_writel(V1, CM_ICLKEN2_CORE); + } +#endif +} + +/**************************************** + * Routine: muxSetupUsb0 (ostboot) + * Description: Setup usb muxing + *****************************************/ +void muxSetupUsb0(void) +{ + mask_config_reg(CONTROL_PADCONF_USB0_PUEN, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_VP, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_VM, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_RCV, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_TXEN, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_SE0, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_DAT, 0x1f); +} + +/**************************************** + * Routine: muxSetupUSBHost (ostboot) + * Description: Setup USB Host muxing + *****************************************/ +void muxSetupUsbHost(void) +{ + /* V19 */ + write_config_reg(CONTROL_PADCONF_USB1_RCV, 1); + /* W20 */ + write_config_reg(CONTROL_PADCONF_USB1_TXEN, 1); + /* N14 */ + write_config_reg(CONTROL_PADCONF_GPIO69, 3); + /* P15 */ + write_config_reg(CONTROL_PADCONF_GPIO70, 3); + /* L18 */ + write_config_reg(CONTROL_PADCONF_GPIO102, 3); + /* L19 */ + write_config_reg(CONTROL_PADCONF_GPIO103, 3); + /* K15 */ + write_config_reg(CONTROL_PADCONF_GPIO104, 3); + /* K14 */ + write_config_reg(CONTROL_PADCONF_GPIO105, 3); +} + +/**************************************** + * Routine: muxSetupUART1 (ostboot) + * Description: Set up uart1 muxing + *****************************************/ +void muxSetupUART1(void) +{ + /* UART1_CTS pin configuration, PIN = D21, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_CTS, 0); + /* UART1_RTS pin configuration, PIN = H21, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_RTS, 0); + /* UART1_TX pin configuration, PIN = L20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_TX, 0); + /* UART1_RX pin configuration, PIN = T21, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_RX, 0); +} + +/**************************************** + * Routine: muxSetupLCD (ostboot) + * Description: Setup lcd muxing + *****************************************/ +void muxSetupLCD(void) +{ + /* LCD_D0 pin configuration, PIN = Y7, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D0, 0); + /* LCD_D1 pin configuration, PIN = P10 , Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D1, 0); + /* LCD_D2 pin configuration, PIN = V8, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D2, 0); + /* LCD_D3 pin configuration, PIN = Y8, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D3, 0); + /* LCD_D4 pin configuration, PIN = W8, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D4, 0); + /* LCD_D5 pin configuration, PIN = R10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D5, 0); + /* LCD_D6 pin configuration, PIN = Y9, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D6, 0); + /* LCD_D7 pin configuration, PIN = V9, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D7, 0); + /* LCD_D8 pin configuration, PIN = W9, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D8, 0); + /* LCD_D9 pin configuration, PIN = P11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D9, 0); + /* LCD_D10 pin configuration, PIN = V10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D10, 0); + /* LCD_D11 pin configuration, PIN = Y10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D11, 0); + /* LCD_D12 pin configuration, PIN = W10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D12, 0); + /* LCD_D13 pin configuration, PIN = R11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D13, 0); + /* LCD_D14 pin configuration, PIN = V11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D14, 0); + /* LCD_D15 pin configuration, PIN = W11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D15, 0); + /* LCD_D16 pin configuration, PIN = P12, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D16, 0); + /* LCD_D17 pin configuration, PIN = R12, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D17, 0); + /* LCD_PCLK pin configuration, PIN = W6, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_PCLK, 0); + /* LCD_VSYNC pin configuration, PIN = V7, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_VSYNC, 0); + /* LCD_HSYNC pin configuration, PIN = Y6, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_HSYNC, 0); + /* LCD_ACBIAS pin configuration, PIN = W7, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_ACBIAS, 0); +} + +/**************************************** + * Routine: muxSetupMMCSD (ostboot) + * Description: set up MMC muxing + *****************************************/ +void muxSetupMMCSD(void) +{ + /* SDMMC_CLKI pin configuration, PIN = H15, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CLKI, 0); + /* SDMMC_CLKO pin configuration, PIN = G19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CLKO, 0); + /* SDMMC_CMD pin configuration, PIN = H18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CMD, 0); + /* SDMMC_DAT0 pin configuration, PIN = F20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT0, 0); + /* SDMMC_DAT1 pin configuration, PIN = H14, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT1, 0); + /* SDMMC_DAT2 pin configuration, PIN = E19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT2, 0); + /* SDMMC_DAT3 pin configuration, PIN = D19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT3, 0); + /* SDMMC_DDIR0 pin configuration, PIN = F19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR0, 0); + /* SDMMC_DDIR1 pin configuration, PIN = E20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR1, 0); + /* SDMMC_DDIR2 pin configuration, PIN = F18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR2, 0); + /* SDMMC_DDIR3 pin configuration, PIN = E18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR3, 0); + /* SDMMC_CDIR pin configuration, PIN = G18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CMD_DIR, 0); +} + +/****************************************** + * Routine: muxSetupTouchScreen (ostboot) + * Description: Set up touch screen muxing + *******************************************/ +void muxSetupTouchScreen(void) +{ + /* SPI1_CLK pin configuration, PIN = U18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_CLK, 0); + /* SPI1_MOSI pin configuration, PIN = V20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_SIMO, 0); + /* SPI1_MISO pin configuration, PIN = T18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_SOMI, 0); + /* SPI1_nCS0 pin configuration, PIN = U19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_NCS0, 0); +#define CONTROL_PADCONF_GPIO85 CONTROL_PADCONF_SPI1_NCS1 + /* PEN_IRQ pin configuration, PIN = N15, Mode = 3, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_GPIO85, 3); +} + +/*************************************************************** + * Routine: muxSetupGPMC (ostboot) + * Description: Configures balls which cam up in protected mode + ***************************************************************/ +void muxSetupGPMC(void) +{ + /* gpmc_io_dir, MCR */ + writel(0x4800008C, 0x19000000); + + /* NOR FLASH CS0 */ + /* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode 0; Byte-3 */ + write_config_reg(CONTROL_PADCONF_GPMC_D2_BYTE3, 0); + /* MPDB(Multi Port Debug Port) CS1 */ + /* signal - gpmc_ncs1; pin - N8; offset - 0x008D; mode 0; Byte-1 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE1, 0); + /* signal - Gpmc_ncs2; pin - E2; offset - 0x008E; mode 0; Byte-2 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE2, 0); + /* signal - Gpmc_ncs3; pin - N2; offset - 0x008F; mode 0; Byte-3 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE3, 0); + /* signal - Gpmc_ncs4; pin - ??; offset - 0x0090; mode 0; Byte-4 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE4, 0); + /* signal - Gpmc_ncs5; pin - ??; offset - 0x0091; mode 0; Byte-5 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE5, 0); + /* signal - Gpmc_ncs6; pin - ??; offset - 0x0092; mode 0; Byte-6 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE6, 0); + /* signal - Gpmc_ncs7; pin - ??; offset - 0x0093; mode 0; Byte-7 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE7, 0); +} + +/**************************************************************** + * Routine: muxSetupSDRC (ostboot) + * Description: Configures balls which come up in protected mode + ****************************************************************/ +void muxSetupSDRC(void) +{ + /* It's set by IPL */ +} diff --git a/board/apollon/config.mk b/board/apollon/config.mk new file mode 100644 index 0000000..45529c8 --- /dev/null +++ b/board/apollon/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2005-2007 +# Samsung Electronics +# +# Samsung December board with OMAP2420 (ARM1136) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# December has 1 bank of 128MB mDDR-SDRAM on CS0 +# December has 1 bank of 00MB mDDR-SDRAM on CS1 +# Physical Address: +# 8000'0000 (bank0) +# A000/0000 (bank1) ES2 will be configurable +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) + +# For use with external or internal boots. +TEXT_BASE = 0x80e80000 + +# Used with full SRAM boot. +# This is either with a GP system or a signed boot image. +# easiest, and safest way to go if you can. +#TEXT_BASE = 0x40270000 + + +# Handy to get symbols to debug ROM version. +#TEXT_BASE = 0x0 +#TEXT_BASE = 0x08000000 +#TEXT_BASE = 0x04000000

1 0

[U-Boot-Users] [PATCH] Typo fix in tsec.c
by urwithsughosh＠gmail.com 15 Sep '07

15 Sep '07

Hello, Fixup for the break statement in wrong place. -- sughosh diff --git a/drivers/tsec.c b/drivers/tsec.c index 6bca4dc..4ff3339 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -1262,10 +1262,10 @@ uint mii_parse_lxt971_sr2(uint mii_reg, struct tsec_private *priv) case MIIM_LXT971_SR2_100HDX: priv->speed = 100; priv->duplexity = 0; + break; default: priv->speed = 100; priv->duplexity = 1; - break; } } else { priv->speed = 0;

3 2

[U-Boot-Users] [PATCH][NAND] Fix do_div() usage in nand process output
by Matthias Fuchs 15 Sep '07

15 Sep '07

Fix usage of do_div() in nand erase|read|write process output. The last patch to nand_util.c introduced do_div() instead of libgcc's implementation. But do_div() returns the quotient in its first macro parameter and not as result. Signed-off-by: Matthias Fuchs <matthias.fuchs(a)esd-electronics.com> --- commit 72ce73aff517363e9fc9fe3ce8c1b21e47ab8fe0 tree 4b241a66240bf37f48cf72c0dc0b19ec3d0d4803 parent 1d9e31e04911a6bb7cc66dd91132c699101c32e2 author Matthias Fuchs <matthias.fuchs(a)esd-electronics.com> Tue, 11 Sep 2007 16:52:29 +0200 committer Matthias Fuchs <matthias.fuchs(a)esd-electronics.com> Tue, 11 Sep 2007 16:52:29 +0200 common/cmd_nand.c | 2 +- drivers/nand/nand_util.c | 21 ++++++++++++++++----- 2 files changed, 17 insertions(+), 6 deletions(-) diff --git a/common/cmd_nand.c b/common/cmd_nand.c index 254a775..34b522b 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -452,7 +452,7 @@ U_BOOT_CMD(nand, 5, 1, do_nand, "info - show available NAND devices\n" "nand device [dev] - show or set current device\n" "nand read[.jffs2] - addr off|partition size\n" - "nand write[.jffs2] - addr off|partiton size - read/write `size' bytes starting\n" + "nand write[.jffs2] - addr off|partition size - read/write `size' bytes starting\n" " at offset `off' to/from memory address `addr'\n" "nand erase [clean] [off size] - erase `size' bytes from\n" " offset `off' (entire device if not specified)\n" diff --git a/drivers/nand/nand_util.c b/drivers/nand/nand_util.c index cf05043..4fd4e16 100644 --- a/drivers/nand/nand_util.c +++ b/drivers/nand/nand_util.c @@ -210,9 +210,12 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) if (!opts->quiet) { unsigned long long n =(unsigned long long) - (erase.addr+meminfo->erasesize-opts->offset) - * 100; - int percent = (int)do_div(n, erase_length); + (erase.addr + meminfo->erasesize - opts->offset) + * 100; + int percent; + + do_div(n, erase_length); + percent = (int)n; /* output progress message only at whole percent * steps to reduce the number of messages printed @@ -478,7 +481,11 @@ int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) if (!opts->quiet) { unsigned long long n = (unsigned long long) (opts->length-imglen) * 100; - int percent = (int)do_div(n, opts->length); + int percent; + + do_div(n, opts->length); + percent = (int)n; + /* output progress message only at whole percent * steps to reduce the number of messages printed * on (slow) serial consoles @@ -653,7 +660,11 @@ int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts) if (!opts->quiet) { unsigned long long n = (unsigned long long) (opts->length-imglen) * 100; - int percent = (int)do_div(n ,opts->length); + int percent; + + do_div(n, opts->length); + percent = (int)n; + /* output progress message only at whole percent * steps to reduce the number of messages printed * on (slow) serial consoles

2 1