November 2006 - U-Boot

[U-Boot-Users] configuring L2 cache in MPC8540 as SRAM
by Selvamuthukumar V 29 Nov '06

29 Nov '06

I'm trying to configure L2 cache in MPC8540 as SRAM. I'm using the following code to do this. volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_l2cache_t *l2cache = &immap->im_l2cache; volatile ccsr_dma_t *dma = &immap->im_dma; int i; asm("mbar;isync"); l2cache->l2ctl = 0x68010000; asm("mbar"); l2cache->l2srbar0 = CFG_L2_SRAM_BASE; asm("mbar;isync"); l2cache->l2ctl = 0xa8010000; asm("mbar"); /* Use DMA to fill memory-mapped SRAM */ dma->satr0 = 0x00040000; dma->sar0 = 0; dma->datr0 = 0x00050000; dma->bcr0 = CFG_L2_SRAM_SIZE; dma->mr0 = 0x0f009404; dma->dar0 = CFG_L2_SRAM_BASE; udelay(1000); I've added TLB entries for SRAM address range in init.S file. After this I'm trying to write to SRAM. But while running from BDI2000 I'm able to write to this SRAM. (i.e) when I execute 'go 0xffffffc' in the BDI prompt I'm able to write and read to SRAM. While booting the board without BDI, U-boot hangs while SRAM is being accessed. Any ideas? Here is part of my BDI configuration file. [INIT] ; ; Move the L2SRAM to the initial MMU page WM32 0xFF720000 0x68010000 ;L2CTL (256k) WM32 0xFF720100 0xFFFC0000 ;L2SRBAR0 (256k) WM32 0xFF720000 0xA8010000 ;L2CTL (256k) ; ; Clear L2SRAM with DMA WM32 0xff721110 0x00040000 ;SATR0 SREADTTYPE=Read, don't snoop WM32 0xff721114 0xff700004 ;SAR0 Dummy source register WM32 0xff721118 0x00050000 ;DATR0 DWRITETTTYPE=Write, snoop local processor WM32 0xff721120 0x00040000 ;BCR0 Size WM32 0xff721100 0x0f009404 ;MR0 BWC=f,SAHTS=2(4 bytes),SAHE=1,SWSM=Dest,SRW=1,CTM=1,CS=0 WM32 0xff72111c 0xfffc0000 ;DAR0 which sets CS=1 DELAY 200 ;let DMA complete WM32 0xff721100 0x00000000 ;MR0 reset condition ; ; load and execute boot code (needed if STARTUP HALT) WM32 0xfffffffc 0x48000000 ;loop EXEC 0xfffffffc 1000 ; WSPR 63 0xffff0000 ;IVPR to boot core WSPR 415 0x0000f000 ;IVOR15 : Debug exception ; ; Remove the L2SRAM from the initial MMU page WM32 0xFF720000 0x28010000 ;L2CTL WM32 0xFF720000 0x28000000 ;L2CTL ; EXEC 0xfffff000 [TARGET] CPUTYPE 8540 ;the CPU type JTAGCLOCK 0 ;use 16 MHz JTAG clock ;STARTUP STOP 4000 ;let boot code setup the system ;STARTUP LOOP ;use boot loop in L2SRAM STARTUP HALT ;halt core while HRESET is asserted BREAKMODE HARD ;SOFT or HARD, HARD uses PPC hardware breakpoint STEPMODE JTAG ;JTAG or HWBP, HWPB uses a hardware breakpoint WAKEUP 200 ;give reset time to complete POWERUP 5000 ;start delay after power-up detected in ms MEMACCESS SAP ;use SAP or CORE for JTAG memory accesses SIO 7 115200 -Selva

1 0

[U-Boot-Users] console initialization
by Luke Kim 29 Nov '06

29 Nov '06

Dear U-boot Developers Hello, my name is Luke Kim from Korea. I've been looking at the u-boot code for debugging, and I think I found something in function 'console_init_r' function in file 'common/console.c'. /***********************line 505****************************/ /* Scan devices looking for input and output devices */ for (i = 1; (i <= items) && ((inputdev == NULL) || (outputdev == NULL)); i++ ) { device_t *dev = ListGetPtrToItem (devlist, i); if ((dev->flags & DEV_FLAGS_INPUT) && (inputdev == NULL)) { inputdev = dev; } if ((dev->flags & DEV_FLAGS_OUTPUT) && (outputdev == NULL)) { outputdev = dev; } } /* Initializes output console first */ if (outputdev != NULL) { console_setfile (stdout, outputdev); console_setfile (stderr, outputdev); } /* Initializes input console */ if (inputdev != NULL) { console_setfile (stdin, inputdev); } gd->flags |= GD_FLG_DEVINIT; /* device initialization completed */ At the last line, it sets the 'GD_FLG_DEVINIT' flag. But doesn't it have to check 'inputdev' and 'outputdev' first to check if it's NULL? I think functions such as 'fputc' will malfunction if the 'GD_FLG_DEVINIT' flag is set when 'stdio_devices' are NULL. Best Regards Luke

1 0

[U-Boot-Users] [PATCH][RESEND] make y-modem a separate config option
by Anders Larsen 29 Nov '06

29 Nov '06

Hi, the loady command (which was introduced this april) bloats the size of U-Boot by almost 4K on my at91 board. The patch below introduces a new option CFG_CMD_LOADY, which can be disabled separately from CFG_CMD_LOADB to save precious space (loadb + loady together take up about 2.5 times as much code space as loadb alone). Perhaps CFG_CMD_LOADY should even be added to CFG_CMD_NONSTD for this reason? Cheers Anders CHANGELOG: Optionally disable the y-modem protocol Patch by Anders Larsen, 06 Jul 2006 Signed-off-by: Anders Larsen <al(a)alarsen.net> --- common/cmd_load.c | 28 +++++++++++++++------------- include/cmd_confdefs.h | 1 + 2 files changed, 16 insertions(+), 13 deletions(-) diff --git a/common/cmd_load.c b/common/cmd_load.c index f63b8e8..5f06129 100644 --- a/common/cmd_load.c +++ b/common/cmd_load.c @@ -33,7 +33,7 @@ DECLARE_GLOBAL_DATA_PTR; -#if (CONFIG_COMMANDS & CFG_CMD_LOADB) +#if (CONFIG_COMMANDS & CFG_CMD_LOADY) static ulong load_serial_ymodem (ulong offset); #endif @@ -404,7 +404,7 @@ write_record (char *buf) #endif /* CFG_CMD_LOADS */ -#if (CONFIG_COMMANDS & CFG_CMD_LOADB) /* loadb command (load binary) included */ +#if (CONFIG_COMMANDS & (CFG_CMD_LOADB | CFG_CMD_LOADY)) /* loadb command (load binary) included */ #define XON_CHAR 17 #define XOFF_CHAR 19 @@ -476,16 +476,7 @@ int do_load_serial_bin (cmd_tbl_t *cmdtp } } - if (strcmp(argv[0],"loady")==0) { - printf ("## Ready for binary (ymodem) download " - "to 0x%08lX at %d bps...\n", - offset, - load_baudrate); - - addr = load_serial_ymodem (offset); - - } else { - + if (strcmp(argv[0],"loadb")==0) { printf ("## Ready for binary (kermit) download " "to 0x%08lX at %d bps...\n", offset, @@ -500,6 +491,15 @@ int do_load_serial_bin (cmd_tbl_t *cmdtp printf ("## Start Addr = 0x%08lX\n", addr); load_addr = addr; } +#if (CONFIG_COMMANDS & CFG_CMD_LOADY) + } else { + printf ("## Ready for binary (ymodem) download " + "to 0x%08lX at %d bps...\n", + offset, + load_baudrate); + + addr = load_serial_ymodem (offset); +#endif } if (load_baudrate != current_baudrate) { printf ("## Switch baudrate to %d bps and press ESC ...\n", @@ -1086,7 +1086,7 @@ U_BOOT_CMD( #endif /* CFG_CMD_LOADS */ -#if (CONFIG_COMMANDS & CFG_CMD_LOADB) +#if (CONFIG_COMMANDS & (CFG_CMD_LOADB | CFG_CMD_LOADY)) U_BOOT_CMD( loadb, 3, 0, do_load_serial_bin, "loadb - load binary file over serial line (kermit mode)\n", @@ -1095,6 +1095,7 @@ U_BOOT_CMD( " with offset 'off' and baudrate 'baud'\n" ); +#if (CONFIG_COMMANDS & CFG_CMD_LOADY) U_BOOT_CMD( loady, 3, 0, do_load_serial_bin, "loady - load binary file over serial line (ymodem mode)\n", @@ -1102,6 +1103,7 @@ U_BOOT_CMD( " - load binary file over serial line" " with offset 'off' and baudrate 'baud'\n" ); +#endif /* CFG_CMD_LOADY */ #endif /* CFG_CMD_LOADB */ diff --git a/include/cmd_confdefs.h b/include/cmd_confdefs.h index cf36583..72b6969 100644 --- a/include/cmd_confdefs.h +++ b/include/cmd_confdefs.h @@ -75,6 +75,7 @@ #define CFG_CMD_FPGA 0x0000010000000000ULL /* FPGA configuration Support */ #define CFG_CMD_HWFLOW 0x0000020000000000ULL /* RTS/CTS hw flow control */ #define CFG_CMD_SAVES 0x0000040000000000ULL /* save S record dump */ +#define CFG_CMD_LOADY 0x0000080000000000ULL /* loady (implies loadb) */ #define CFG_CMD_SPI 0x0000100000000000ULL /* SPI utility */ #define CFG_CMD_FDOS 0x0000200000000000ULL /* Floppy DOS support */ #define CFG_CMD_VFD 0x0000400000000000ULL /* VFD support (TRAB) */

2 4

[U-Boot-Users] Can U-boot support CFI and None CFI devices on the same board
by Yotam Admon 28 Nov '06

28 Nov '06

Hi, I use U-Boot (1.1.4) and try to work with AM29LV040B (AMD None CFI Flash) in addition to known CFI flash devices (AMD, Intel, MXIC, SST). Does anyone have a way to integrate the CFI deriver with none CFI devices? Thanks, Yotam

5 5

[U-Boot-Users] McBsp Interface on OMAP - Uboot
by Ram 28 Nov '06

28 Nov '06

Hi, I have been asked to test McBsp interface on OMAP. Im configuring the Aic29 Codec and McBsp and am writing a square wave pattern. Its not working, im not able see anything on the CRO when i probe. Before witing to the McBsp, i ensure that the previous data is read, So i read Serial Port Control Register (SPCR1) and check for RFULL bit(Reciever Full Bit). Whenever, i read im getting 0xFFFF. The reset value for this register is 0x0000. Atleast i should get the reset value when i read, isnt it?. Im directly reading the physical address of the register as given by the datasheet. Do i need to do something - so that whenever i access that particular address, it actually accesses the mcbsp register. Im not sure if it a memory map problem or something else, im unable to figure out what could be wrong. Can you help me on this. Thanks, Regards, sriram

2 1

Re: [U-Boot-Users] [DNX#2006112842000034] hi
by DENX Support System 28 Nov '06

28 Nov '06

Hello list, inside the automatic U-Boot patch tracking system a new ticket [DNX#2006112842000034] was created: <snip> > Hi </snip> Your U-Boot support team

1 0

Re: [U-Boot-Users] [DNX#2006112842000034] hi
by U-Boot patch tracking system 28 Nov '06

28 Nov '06

Dear Mr. U. Boot, thank you for your contribution to the U-Boot project. Your e-mail was registered at our system under the ticket number [DNX#2006112842000034]. Please keep this ticket ID string in the subject line of any e-mail replies!!! Your U-Boot support team Powered by OTRS (http://otrs.org/)

1 0

[U-Boot-Users] [PATCH][RESEND] Fix AT91RM9200 Ethernet initialization
by Anders Larsen 28 Nov '06

28 Nov '06

Hi, the AT91RM9200 on-chip Ethernet interface is explicitly initialized to use promiscuous mode. This is probably due to a bug in line 183 of cpu/arm920t/at91rm9200/ether.c which was supposed to clear the statistics counters but instead erroneously disabled reception of broadcast packets - so the driver later enables promiscuous mode in order to receive such broadcasts, like e.g. DHCP responses. The patch below fixes the original bug and lets the interface run in normal (non-promiscuous) mode, which should improve performance on networks with heavy traffic. Cheers Anders CHANGELOG: Fix the initialization of the AT91RM9200 ethernet interface to use non-promiscuous mode Patch by Lars Munch, 24 Oct 2005 Signed-off-by: Anders Larsen <al(a)alarsen.net> --- cpu/arm920t/at91rm9200/ether.c | 5 ++--- 1 files changed, 2 insertions(+), 3 deletions(-) diff --git a/cpu/arm920t/at91rm9200/ether.c b/cpu/arm920t/at91rm9200/ether.c index 67008d0..46dd36c 100644 --- a/cpu/arm920t/at91rm9200/ether.c +++ b/cpu/arm920t/at91rm9200/ether.c @@ -180,7 +180,7 @@ int eth_init (bd_t * bd) *AT91C_PMC_PCER = 1 << AT91C_ID_EMAC; /* Peripheral Clock Enable Register */ - p_mac->EMAC_CFG |= AT91C_EMAC_CSR; /* Clear statistics */ + p_mac->EMAC_CTL |= AT91C_EMAC_CSR; /* Clear statistics */ /* Init Ehternet buffers */ for (i = 0; i < RBF_FRAMEMAX; i++) { @@ -197,8 +197,7 @@ int eth_init (bd_t * bd) p_mac->EMAC_RBQP = (long) (&rbfdt[0]); p_mac->EMAC_RSR &= ~(AT91C_EMAC_RSR_OVR | AT91C_EMAC_REC | AT91C_EMAC_BNA); - p_mac->EMAC_CFG = (p_mac->EMAC_CFG | AT91C_EMAC_CAF | AT91C_EMAC_NBC) - & ~AT91C_EMAC_CLK; + p_mac->EMAC_CFG &= ~AT91C_EMAC_CLK; #ifdef CONFIG_AT91C_USE_RMII p_mac->EMAC_CFG |= AT91C_EMAC_RMII;

1 0

[U-Boot-Users] [PATCH][RESEND] eliminate assumptions about dataflash layout
by Anders Larsen 28 Nov '06

28 Nov '06

Hi, the dataflash driver contains a hard-coded partition table which might suit one particular board (which I doubt, however) but certainly isn't generally applicable. Furthermore, it write-protects the first two partitions, which violates the U-Boot standard of allowing the user enough rope to shoot himself in the foot. Besides, the dataflash partitions aren't even on sector boundaries (the dataflash chips have rather unusual sector sizes; 528 or 1056 bytes, which makes one wonder what the folks at Atmel are smoking). The patch below places the entire dataflash in one (writable) partition. Cheers Anders CHANGELOG: Don't make assumptions about dataflash layout Patch by Anders Larsen, 13 Oct 2005 Signed-off-by: Anders Larsen <al(a)alarsen.net> --- drivers/dataflash.c | 7 ++----- include/dataflash.h | 4 ++-- 2 files changed, 4 insertions(+), 7 deletions(-) diff --git a/drivers/dataflash.c b/drivers/dataflash.c index 17eb859..62a2029 100644 --- a/drivers/dataflash.c +++ b/drivers/dataflash.c @@ -33,10 +33,7 @@ int cs[][CFG_MAX_DATAFLASH_BANKS] = { /*define the area offsets*/ dataflash_protect_t area_list[NB_DATAFLASH_AREA] = { - {0, 0x7fff, FLAG_PROTECT_SET}, /* ROM code */ - {0x8000, 0x1ffff, FLAG_PROTECT_SET}, /* u-boot code */ - {0x20000, 0x27fff, FLAG_PROTECT_CLEAR}, /* u-boot environment */ - {0x28000, 0x1fffff, FLAG_PROTECT_CLEAR}, /* data area size to tune */ + {0, 0x1fffff, FLAG_PROTECT_CLEAR}, /* filesystem */ }; extern void AT91F_SpiInit (void); @@ -110,7 +107,7 @@ int AT91F_DataflashInit (void) break; } /* set the last area end to the dataflash size*/ - area_list[NB_DATAFLASH_AREA -1].end = + area_list[NB_DATAFLASH_AREA - 1].end = (dataflash_info[i].Device.pages_number * dataflash_info[i].Device.pages_size)-1; diff --git a/include/dataflash.h b/include/dataflash.h index 650454e..825eec6 100644 --- a/include/dataflash.h +++ b/include/dataflash.h @@ -37,8 +37,8 @@ #include <asm/arch/hardware.h> #include "config.h" -/*number of protected area*/ -#define NB_DATAFLASH_AREA 4 +/*number of areas*/ +#define NB_DATAFLASH_AREA 1 /*define the area structure*/ typedef struct {

1 0

[U-Boot-Users] [PATCH] 4xx_enet.c: Correct the setting of zmiifer register.
by Neil Wilson 28 Nov '06

28 Nov '06

Patch below corrects the setting of the zmiifer register, it was overwritting the register rather than ORing the settings. Neil -- Neil Wilson Principal Engineer, Embedded Software Airspan Communications Ltd Cambridge House, Oxford Road Uxbridge, Middlesex, UB8 1UN, UK. +44(0)1895-467265 neilwilson(a)airspan.com -- diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 81d49ff..aefe126 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -264,10 +264,10 @@ int ppc_4xx_eth_setup_bridge(int devnum, bis->bi_phymode[3] = BI_PHYMODE_ZMII; break; case 2: - zmiifer = ZMII_FER_SMII << ZMII_FER_V(0); - zmiifer = ZMII_FER_SMII << ZMII_FER_V(1); - zmiifer = ZMII_FER_SMII << ZMII_FER_V(2); - zmiifer = ZMII_FER_SMII << ZMII_FER_V(3); + zmiifer |= ZMII_FER_SMII << ZMII_FER_V(0); + zmiifer |= ZMII_FER_SMII << ZMII_FER_V(1); + zmiifer |= ZMII_FER_SMII << ZMII_FER_V(2); + zmiifer |= ZMII_FER_SMII << ZMII_FER_V(3); bis->bi_phymode[0] = BI_PHYMODE_ZMII; bis->bi_phymode[1] = BI_PHYMODE_ZMII; bis->bi_phymode[2] = BI_PHYMODE_ZMII;

2 1

[U-Boot-Users] Changes to NAND bootloader so that all boards don't have to use embedded environment variables
by Nick Spence 28 Nov '06

28 Nov '06

Changelog: Make NAND bootloader environment variable location board specific - Nick

2 1

[U-Boot-Users] [PATCH] nand_wait() timeout fixes
by Rui Sousa 28 Nov '06

28 Nov '06

Hi, Two fixes for the nand_wait() function in drivers/nand/nand_base.c: 1. Use correct timeouts. The original timeouts in Linux source are 400ms and 20ms not 40s and 20s 2. Return correct error value in case of timeout. 0 is interpreted as OK. Please apply, Rui

2 1

[U-Boot-Users] arm1176 port related query...
by Hemant Pedanekar 28 Nov '06

28 Nov '06

Hello All, We are planning to port U-Boot on board having arm1176. I see that the current uboot supports arm1136 but not arm1176 yet. My initial assessment is that I shout be able to use cpu/arm1136 code as is (cpu/arm1176) at lest for early init since both are armv6. Could you please let me know if my guess is correct? Also, I even hope that I could use complete arm1136 code as is owing to the difference related to secure mode, TCMs, Smart Cache and a few debug related changes. Is this right? Thanks, Hemant. *"97.25% of statistics are wrong."*

1 0

[U-Boot-Users] viewing files on JFFS2/NAND flash
by Charles Krinke 27 Nov '06

27 Nov '06

I have implemented the macros for JFFS2/NAND flash access and can do an mtd, mtdparts or ls command, like this: I8000E> mtd device nand0 <atx-0>, # parts = 3 #: name size offset mask_flags 0: rootfs1 0x01000000 0x00000000 0 1: rootfs2 0x01000000 0x01000000 0 2: MPUapps 0x06000000 0x02000000 0 active partition: nand0,0 - (rootfs1) 0x01000000 @ 0x00000000 defaults: mtdids : nand0=atx-0 mtdparts: mtdparts=atx-0:-@1m(jffs2) I8000E> ls rescan: First time in use Scanning JFFS2 FS: done. ******The directory Entries****** ******The fragment Entries****** I8000E> However, my problem is that I have written some files from Linux onto these three partitions and then when I reboot, I do not see the files from u-boot. If I then do a complete boot to Linux, I can ls the files from linux and display their contents. There must be something silly I am doing (or not doing) that precludes me from viewing the files on the JFFS2/NAND flash partitions that were written from Linux. I wonder if you would be so kind as to offer a suggestion or two for a way to move forward. Charles

1 0

[U-Boot-Users] Booting ELDK 4.0 kernel on MPC8548CDS
by Thomas Schafer 27 Nov '06

27 Nov '06

Hi, I'm using a MPC8548CDS eval system with u-boot 1.1.6 running on it. When trying to boot an ELDK 4.0 kernel, the board hangs immediately after decompression of the kernel. I've set the disable_of environment variable to avoid usage of the flat device tree. The same kernel boots properly when using u-boot 1.1.3 which is delivered with the eval system. Any hints would be appreciated. Best regards, Thomas Schafer ____________________________________ Kontron Modular Computers GmbH Heinrich-Barth-Str. 1a 66115 Saarbrucken Tel.: + 49 (0)681 / 95916 - 203 Fax: + 49 (0)681 / 95916 - 100 E-mail: thomas.schaefer(a)kontron.com

5 5

[U-Boot-Users] U-boot-1.1.4 on MPC8540
by revathy 27 Nov '06

27 Nov '06

Hi all, I'm booting a newly compiled u-boot-1.1.4 image on my MPC8540, and it doesn't work. It hangs after this.. ************************************** U-Boot 1.1.4 (Nov 23 2006 - 10:34:07) Freescale PowerPC Core: E500, Version: 2.0, (0x80200020) CPU: 8540, Version: 2.0, (0x80300020) Clock Configuration: CPU: 825 MHz, CCB: 330 MHz, DDR: 165 MHz, LBC: 82 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled CPU: 825 MHz CCB: 330 MHz DDR: 165 MHz LBC: 82 MHz L1 D-cache 32KB, L1 I-cache 32KB enabled. I2C: ready DRAM: 256 MB PCIG8400 in PCI Host Mode. PCIG8400 not PCI Arbiter. ******************************************** I've carefully copied every setup from the u-boot-1.1.2 image which I've made. Now, how do I debug this,any help is greatly appreciated. Thanks in advance. Revathy

3 5

[U-Boot-Users] [PATCH] PPC 4xx Start.S: Fix for processor error
by Jeff Mann 27 Nov '06

27 Nov '06

Hello u-boot users: This patch further corrects errata 1.12: 440_33. We came across a problem affecting around 20% of 440EPx processors in which it took multiple resets to start the processor after a cold power up. In resolving the problem, it was discovered that the above mentioned errata correction in the startup code in start.S was never reached. This patch resolves that problem by moving up the errata correction erlier in the code. One of our software engineers hypothesizes that this patch, store gathering & broadcast disable, must happen before doing a jump. [PATCH] Fixed cpu/ppc4xx/start.S for Epx Errata - further corrects PPC440EPx errata 1.12: 440_33 by moving patch up in code Signed-off-by: Jeff Mann <mannj(a)embeddedplanet.com>

2 1

[U-Boot-Users] MC68360 port
by Matvejchikov Ilya 26 Nov '06

26 Nov '06

Hi all, I have ported U-Boot-1.1.6 to MC68360 based board. See the attached file for details. E-mail me if you have any questions :) Best regards, Matvejchikov Ilya, Russia, Moscow.

4 9

[U-Boot-Users] : MPC8360: CFG_INIT_RAM_ADDR
by ananthsl＠libero.it 26 Nov '06

26 Nov '06

Hi, In the uboot code for a MPC8360-based evaluation board, the initial RAM address (CFG_INIT_RAM_ADDR) is set to 0xE6000000. But, this address is not mapped to any device nor to the Internal config. registers in the board memory map. If I need to port uboot , how do I decide what address to use for the CFG_INIT_RAM_ADDR? Thanks and Regards, Ananth. ------------------------------------------------------ Passa a Infostrada. ADSL e Telefono senza limiti e senza canone Telecom http://click.libero.it/infostrada26nov06

3 2

[U-Boot-Users] tuition
by Nunez 26 Nov '06

26 Nov '06

Answer in the comments section California - For a state that prides itself on being the biggest, the best,. Online auction site eBay and the search engine giant announced a deal which will place Google text ads, exclusively, on eBay sites outside the U. Writing now with this peace and enlightenment, I find little to quarrel with about the path our leaders have chosen. Thirty-seven percent of posts. I stand united with most direct response copywriters in supporting long copy over. Here are a few reminders about freezing desserts. Most of the people writing back to you have no. Thirty-seven percent of posts. and so many other basics. Answer in the comments section California - For a state that prides itself on being the biggest, the best,. Even copywriters argue with other copywriters about it. Creativity is death to results-oriented copywriting. I experience a special joy when I pick it up for the first time, open the cover, inhale. Just follow this recipe and add apples plus a few other ingredients to make a great Mincemeat. Innovation is not only the breath of life, but the wellspring of wealth. Just follow this recipe and add apples plus a few other ingredients to make a great Mincemeat. At least until, I regain the ability to go on. Thirty-seven percent of posts. A year later, he appointed her to the Texas Lottery Commission. Creativity is death to results-oriented copywriting. At least until, I regain the ability to go on. The time-tested way to solve this problem is a testimonial quote. It will be well worth your while. So far there is only going to be a limited release, so, if you can go to one of the the theatres here, you should. Innovation is not only the breath of life, but the wellspring of wealth. I'm thankful for God, my family, friends and for you.

1 0

[U-Boot-Users] hay
by Katharine E. Brandon 26 Nov '06

26 Nov '06

Sign up while this offer lasts! Of course, those times witnessed the Korean War, the Cold War, the Whittaker Chambers-Alger Hiss Trial, the Rosenbergs, etc. This professionally written guide is absolutely FREE with no strings attached! Select from THOUSANDS of available items and place your bid! com, Your Local Marketplace. A new contest every weekday! com Steal O' The Day! All the drugs, herbs, vitamins, minerals, supplements, bananas, apples, grapes and whatever else you try are not treating the problem, they are treating the symptoms. A new contest every weekday! Find the right item, place your bid and try to win collectibles, sporting goods, electronics, computers, art, baby goods and more! Join for free by clicking through the link and entering your email address on the form. com Steal O' The Day! Click to learn more about this dog training information. You get groceries on a weekly basis. Now, I can tell the story and make it sound immensely amusing - or potentially tragic - you decide which. msi file by using the Orca database editor. com - FREE Internet Safety Ebook! Find out important security tips, dangers to watch out for, and read reviews of the most popular parental control products. This article describes how to implement the line-based interface. Click to learn more about this dog training information. Just think of what you are going to use that extra money for! The place to buy and sell. com - Steal O' The Day! Until a certain facility or level is reached, it may be that students need a rest and chance to speak their first language. Provides the steps to edit the .

1 0

Re: [U-Boot-Users] [DNX#2006112542000012] [PATCH] fix at91rm9200 configs
by U-Boot patch tracking system 25 Nov '06

25 Nov '06

Dear Mr. U. Boot, thank you for your contribution to the U-Boot project. Your e-mail was registered at our system under the ticket number [DNX#2006112542000012]. Please keep this ticket ID string in the subject line of any e-mail replies!!! Your U-Boot support team Powered by OTRS (http://otrs.org/)

1 0

Re: [U-Boot-Users] [DNX#2006112542000012] [PATCH] fix at91rm9200 configs
by DENX Support System 25 Nov '06

25 Nov '06

Hello list, inside the automatic U-Boot patch tracking system a new ticket [DNX#2006112542000012] was created: <snip> > Somewhere during development of U-Boot-1.1.3 CONFIG_BOOTBINFUNC was > renamed into CONFIG_INIT_CRITICAL which was 04 Apr 2005 replaced > with CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT. > However CONFIG_SKIP_LOWLEVEL_INIT has oposite meaning to > CONFIG_BOOTBINFUNC, so fix configuration to reflect this fact. > Once here, fix whitespaces and remove nowhere used struct bd_info_ext. > > > CHANGELOG > * Fix U-Boot base address depending on CONFIG_SKIP_LOWLEVEL_INIT > > Signed-off-by: Ladislav Michl <ladis(a)linux-mips.org> > > diff --git a/include/configs/at91rm9200dk.h > b/include/configs/at91rm9200dk.h > index 8fad55d..ee0c395 100644 > --- a/include/configs/at91rm9200dk.h > +++ b/include/configs/at91rm9200dk.h > @@ -152,8 +152,8 @@ > > #define CONFIG_HAS_DATAFLASH 1 > #define CFG_SPI_WRITE_TOUT (5*CFG_HZ) > -#define CFG_MAX_DATAFLASH_BANKS 2 > -#define CFG_MAX_DATAFLASH_PAGES 16384 > +#define CFG_MAX_DATAFLASH_BANKS 2 > +#define CFG_MAX_DATAFLASH_PAGES 16384 > #define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* Logical adress for > CS0 */ > #define CFG_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* Logical adress for > CS3 */ > > @@ -174,11 +174,11 @@ > #else > #define CFG_ENV_IS_IN_FLASH 1 > #ifdef CONFIG_SKIP_LOWLEVEL_INIT > -#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x60000) /* after u-boot.bin */ > -#define CFG_ENV_SIZE 0x10000 /* sectors are 64K here */ > -#else > #define CFG_ENV_ADDR (PHYS_FLASH_1 + 0xe000) /* between boot.bin and > u-boot.bin.gz */ > #define CFG_ENV_SIZE 0x2000 /* 0x8000 */ > +#else > +#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x60000) /* after u-boot.bin */ > +#define CFG_ENV_SIZE 0x10000 /* sectors are 64K here */ > #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ > #endif /* CFG_ENV_IS_IN_DATAFLASH */ > > @@ -186,44 +186,25 @@ > #define CFG_LOAD_ADDR 0x21000000 /* default load address */ > > #ifdef CONFIG_SKIP_LOWLEVEL_INIT > -#define CFG_BOOT_SIZE 0x00 /* 0 KBytes */ > -#define CFG_U_BOOT_BASE PHYS_FLASH_1 > -#define CFG_U_BOOT_SIZE 0x60000 /* 384 KBytes */ > -#else > #define CFG_BOOT_SIZE 0x6000 /* 24 KBytes */ > #define CFG_U_BOOT_BASE (PHYS_FLASH_1 + 0x10000) > #define CFG_U_BOOT_SIZE 0x10000 /* 64 KBytes */ > +#else > +#define CFG_BOOT_SIZE 0x00 /* 0 KBytes */ > +#define CFG_U_BOOT_BASE PHYS_FLASH_1 > +#define CFG_U_BOOT_SIZE 0x60000 /* 384 KBytes */ > #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ > > -#define CFG_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } > +#define CFG_BAUDRATE_TABLE { 115200, 19200, 38400, 57600, 9600 } > > #define CFG_PROMPT "U-Boot> " /* Monitor Command Prompt */ > #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ > #define CFG_MAXARGS 16 /* max number of command args */ > #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer > Size */ > > -#ifndef __ASSEMBLY__ > -/*----------------------------------------------------------------------- > - * Board specific extension for bd_info > - * > - * This structure is embedded in the global bd_info (bd_t) structure > - * and can be used by the board specific code (eg board/...) > - */ > - > -struct bd_info_ext { > - /* helper variable for board environment handling > - * > - * env_crc_valid == 0 => uninitialised > - * env_crc_valid > 0 => environment crc in flash is valid > - * env_crc_valid < 0 => environment crc in flash is invalid > - */ > - int env_crc_valid; > -}; > -#endif > - > #define CFG_HZ 1000 > #define CFG_HZ_CLOCK AT91C_MASTER_CLOCK/2 /* AT91C_TC0_CMR is > implicitly set to */ > - /* AT91C_TC_TIMER_DIV1_CLOCK */ > + /* AT91C_TC_TIMER_DIV1_CLOCK */ > > #define CONFIG_STACKSIZE (32*1024) /* regular stack */ > </snip> Your U-Boot support team

1 0

[U-Boot-Users] Everton have decided not to appeal the decision by the way.
by Reyna 25 Nov '06

25 Nov '06

winter steelhead are showing on the Cowlitz, and Bob Ferber at Holiday Market Sports . training, documentation or guidance to people that will

1 0

[U-Boot-Users] Its distinction is that both its content and design are generated by its users.
by Sal 24 Nov '06

24 Nov '06

In each, our tools for encouraging sharing are encouraging a much wider range of creativity. We responded to his unique use of the CC, his composition, use of focus, and the decision to use black and white. Users choose what should or should not be published on the website. That much we expected when we launched CC four years ago. 5555 *** CNHC *** CNHC *** CNHC *** Trade Date: Friday, November 24, 2006 Company: China Health Management Corp. Symbol: CNHC Price: $1.34 Target: $10 CNHC BREAKING NEWS: China Health Management Corp. Announces the Hospital's Setup Proposal Received Additional Approval from Kunming City, Yunnan, China CNHC IS BOUND TO BLOW UP! THIS AMAZING NEWS ALONG WITH HEAVY PR PROMOS ARE DRIVING IT NUTS! WATCH CNHC GO OFF THE CHAIN ON FRIDAY NOV 24! 5555 Join the "Avatar Chess" SL group, and contact Barney to play for the white team or Neit Tackleberry to compete on the red side. Join the "Avatar Chess" SL group, and contact Barney to play for the white team or Neit Tackleberry to compete on the red side. I do not have PowerPoint on my computer. Its distinction is that both its content and design are generated by its users. Look Ma No Photoshop A new Robin Good Mini-Guide is out! John's expertise in this area will be hugely beneficial. For certainly the most exciting work in spreading CC is going on in cultures far from our headquarters in San Francisco. Obviously it is a huge win for search engines and webmasters if all agree to use the same protocol. I answered Jin that this was indeed a difficult question, one that I have run into before and which has had me spend quite a few hours to find an appropriate solution. A basic collection drawn from the archive will be made available on the Internet either under CC licenses, or in some cases, in the public domain. For certainly the most exciting work in spreading CC is going on in cultures far from our headquarters in San Francisco. Brush up on your chess strategy and tactics, or just take snapshots! Many of you wrote that you were surprised by the examples, and were especially excited that the applications reached so broadly internationally. Its distinction is that both its content and design are generated by its users. Although inputting text into individual slides is the spontaneous approach that most users take, due to the above reasons, it is not the most efficient one. Here I try to explain my problem. , and Microsoft many hours of legal haggling over copyright in the protocol. For certainly the most exciting work in spreading CC is going on in cultures far from our headquarters in San Francisco. Theora is a high quality video codec that is not patent encumbered. The issue I am finding is as follows: I am copying this presentation including the files on a CD-ROM however, when I try to run this on the CD-ROM the links do not work. Autant alors savoir vers qui se tourner. It is not a guess that this decision allows anyone, e. A moins que ce ne soit un de ses proches. In each, our tools for encouraging sharing are encouraging a much wider range of creativity. , non-incumbent search engines, to publish and extend the protocol, without asking for permission from the incumbents. This photo in no way shapes the context of this contest - we are open to all entries as long as the work supports both your vision of CC and CC's mission by using CC Swag. My training supports are all in PowerPoint and I also help the speakers to prepare their visuals in PowerPoint for their presentations. I sometimes use a Wacom tablet to be able to write directly to the screen during a training presentation, but such an approach is not very attractive for professional presentations. On the introduction page I made hyperlinks to several slides. Moyennant certaines conditions. Ultimately, the team hopes that the competition will develop new sounds that young start-up musicians can use to advance their own musical careers. John's expertise in this area will be hugely beneficial. Obviously it is a huge win for search engines and webmasters if all agree to use the same protocol. The Netherlands may be a small country, but if it is successful, the "Images for the Future" project may well be the largest archive of free culture available anywhere in the world. But the scale and values of this project are extraordinary. That much we expected when we launched CC four years ago. The winner of that contest will have their remix featured on the b-side to an upcoming Cursive single. , commercial or derivative use. We responded to his unique use of the CC, his composition, use of focus, and the decision to use black and white. " We thank Sun for their continued support as we will be able to continue realizing the mission of helping to enable a participatory culture, a global digital commons, for another year. I have a lot to say about how CC principles can be applied successfully to the for-profit world. The winner of that contest will have their remix featured on the b-side to an upcoming Cursive single. Microsoft Research has a nice article on creating cartoon movies from digital video. TechSmith's Camtasia Producer allows you to create movies from screen captures - and then edit and distribute the videos. , and Microsoft many hours of legal haggling over copyright in the protocol. The issue I am finding is as follows: I am copying this presentation including the files on a CD-ROM however, when I try to run this on the CD-ROM the links do not work. The winner of that contest will have their remix featured on the b-side to an upcoming Cursive single.

1 0