December 2005 - U-Boot

[U-Boot-Users] Banned file: document.pif in mail from you
by MAILER DAEMON 19 Dec '05

19 Dec '05

BANNED FILENAME ALERT Your message to: jean-philippe.moreno(a)rfo.atmel.com was blocked by our Spam Firewall. The email you sent with the following subject has NOT BEEN DELIVERED: Subject: Error An attachment in that mail was of a file type that the Spam Firewall is set to block.

1 0

[U-Boot-Users] Help with PCI using NPe405H
by Sugeno, Otavio Isamu 16 Dec '05

16 Dec '05

Hi everybody. I am having some problems to configure PCI interfcace in the NPe405H processor. Have anyone already ported u-boot to it? Basically, the problem happens when u-boot tries to scan the bus. Function pci_hose_scan_bus tries to read a byte (Header Type) and a word (Vendor ID) but it does not return anymore from this function. Can anyone help me. Regards Otavio I. Sugeno

2 1

[U-Boot-Users] Freezing & Unfreezing the au11000
by Rodolfo Giometti 16 Dec '05

16 Dec '05

I'm just trying to support the save_and_sleep() support into u-boot for an au1100 based board. Into u-boot I added the following code: Index: cpu/mips/start.S =================================================================== RCS file: /home/develop/cvs_private/uboot-mips-exadron/cpu/mips/start.S,v retrieving revision 1.2 diff -u -r1.2 start.S --- cpu/mips/start.S 12 Oct 2005 12:55:54 -0000 1.2 +++ cpu/mips/start.S 16 Dec 2005 15:29:22 -0000 @@ -26,6 +26,7 @@ #include <config.h> #include <version.h> #include <asm/regdef.h> +#include <asm/au1x00.h> #include <asm/mipsregs.h> @@ -273,6 +274,33 @@ li t0, CONF_CM_CACHABLE_NONCOHERENT mtc0 t0, CP0_CONFIG + /* Now check the wakeup cause + */ + li t0, SYS_WAKESRC + lw t1, 0(t0) + andi t1, t1, 0x00000002 /* check the SW bit */ + beq zero, t1, 1f + nop + + li t0, SYS_SCRATCH0 + lw t1, 0(t0) + move sp, t1 + li t0, SYS_SCRATCH1 + lw t1, 0(t0) + j t1 /* this cause a jump into already + nop frozen Linux (brr! :) */ + + /* If we reach this point we come from a normal system power up, + so just clear the wakeup cause registers + */ + +1: li t0, SYS_WAKEMSK + li t1, 0x00000000 + sw t1, 0(t0) + + li t0, SYS_WAKESRC + li t1, 0x00000000 + sw t1, 0(t0) /* Set up temporary stack. */ in order to restore the scratch registers contents as descibed into file "linux/arch/mips/au1000/common/sleeper.S": /* Now set up the scratch registers so the boot rom will * return to this point upon wakeup. */ la k0, 1f lui k1, 0xb190 ori k1, 0x18 sw sp, 0(k1) ori k1, 0x1c sw k0, 0(k1) However it seems something is wrong since the system at the end of save_and_sleep() does not correctly continue its execution... Unlikely my JTAG do not allow me to follow the code after the save_and_sleep()'s return (I definitely have to buy a better one), however I noticed that when the system tryes to resume the register 29 (the sp) doing: lw $29, PT_R29(sp) something goes wrong! Suggestions? :) Thanks in advance, Rodolfo -- GNU/Linux Solutions e-mail: giometti(a)enneenne.com Linux Device Driver giometti(a)gnudd.com Embedded Systems giometti(a)linux.it UNIX programming phone: +39 349 2432127

1 0

Re: [U-Boot-Users] About a make error: "too many `l's in integer constant"
by James Chen (ꐏ┩�) 16 Dec '05

16 Dec '05

I tried the ELDK toolchain (version arm-2005-03-06.iso), but this error still occurs. Best Regards. On 12/14/05, Wolfgang Denk <wd(a)denx.de> wrote: > In message <eca8910f0512140716l197e80f6o388a987ab9d9ecf(a)mail.gmail.com> you wrote: > > > > 1. Is there any website providing workable toolchain for u-boot? > > You can use the ELDK; see http://www.denx.de/wiki/view/DULG/ELDKAvailability > > > 2. The following patch solves my problem, but I am not sure why this works? > > Neither am I. But your toolchain must be badly misconfigured or > otherwise broken, so who knows. > > Best regards, > > Wolfgang Denk > > -- > Software Engineering: Embedded and Realtime Systems, Embedded Linux > Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd(a)denx.de > It may be that your whole purpose in life is simply to serve as a > warning to others. >

3 3

[U-Boot-Users] About a make error: "too many `l's in integer constant"
by James Chen (ꐏ┩�) 16 Dec '05

16 Dec '05

Dear all, I want to build a image for SMDK2410, so I do the following: $ make smdk2410_config $ make all But I got this error message: make -C tools all make[1]: Entering directory `/home/cyt/svnwork/u-boot/u-boot-1.1.3/trunk/tools' gcc -Wall -pedantic -idirafter ../include -DTEXT_BASE=0x33F80000 -DUSE_HOSTCC -O -c -o img2srec.o img2srec.c gcc -Wall -pedantic -idirafter ../include -DTEXT_BASE=0x33F80000 -DUSE_HOSTCC -O -o img2srec img2srec.o strip img2srec gcc -g -Wall -pedantic -idirafter ../include -DTEXT_BASE=0x33F80000 -DUSE_HOSTCC -O -c mkimage.c gcc -g -Wall -pedantic -idirafter ../include -DTEXT_BASE=0x33F80000 -DUSE_HOSTCC -O -c crc32.c gcc -Wall -pedantic -idirafter ../include -DTEXT_BASE=0x33F80000 -DUSE_HOSTCC -O -o mkimage mkimage.o crc32.o strip mkimage gcc -g -Wall -pedantic -idirafter ../include -DTEXT_BASE=0x33F80000 -DUSE_HOSTCC -O -c envcrc.c In file included from ../include/config.h:2, from envcrc.c:32: ../include/configs/smdk2410.h:101: too many `l's in integer constant make[1]: *** [envcrc.o] Error 1 make[1]: Leaving directory `/home/cyt/svnwork/u-boot/u-boot-1.1.3/trunk/tools' make: *** [tools] Error 2 My arm-linux-gcc is 3.2. I cannot figure out what this message means? Any suggestions? Thanks.

2 3

[U-Boot-Users] Help required to bring up kernel from U-Boot
by batsayan.das＠tcs.com 16 Dec '05

16 Dec '05

Hello, I am using MPC8260ADS based customs board. I have configured the memory map in U-Boot as follows SDRAM : 0x00000000 (size=128 MB) FLASH : 0x30000000 (size= 1MB) SRAM : 0xFFF00000 (size 4MB) There are also other components in the board, like FRAMER , DSP, etc. I have not initialized the memory map of those components in U-Boot. I am able to get the U-Boot prompt when run by TRACE23. I have build a default MPC8260ADS kernel, the only changes I have made is in the variable IMAP_ADDR , BCSR_ADDR in arch/ppc/platforms/ads8260.h. I have put those values from the already running U-Boot code. Our TEXT_BASE=0xFFF00000 HRCW value= "0E A2 82 05" I copied uImage to location 0x04000000 and the Load Address=0x00000000 and Entry point=0x00000000. The bootm 0x04000000 gives the o/p "Transferring Control to Linux" and then nothing comes. Where is the wrong? My question is 1. What are the minimum information Linux needs from U-Boot to come up properly? In the Linux source tree we have put some printk statement and found that base address of SDRAM, size, etc are passed correctly to Linux by U-Boot. 2. Is the info passed from U-Boot is sufficient enough to make the kernel up? 3. If not, where should I concentrate in Linux tree? Pls help. Thanks, Batsayan Das Tata Consultancy Services Limited Mailto: batsayan.das(a)tcs.com Website: http://www.tcs.com Notice: The information contained in this e-mail message and/or attachments to it may contain confidential or privileged information. If you are not the intended recipient, any dissemination, use, review, distribution, printing or copying of the information contained in this e-mail message and/or attachments to it are strictly prohibited. If you have received this communication in error, please notify us by reply e-mail or telephone and immediately and permanently delete the message and any attachments. Thank you

2 1

[U-Boot-Users] [PATCH] STXXTC Nand support.
by Pantelis Antoniou 15 Dec '05

15 Dec '05

Hi Wolfgang. The following patch supports the NAND present on the Silicon Turnkey's XTc board. The patch is against the testing-NAND branch of u-boot. ----------8< CHANGELOG 8<------------------ * Support NAND on STXXTC ----------8< patch 8<---------------------- --- a/board/stxxtc/Makefile +++ b/board/stxxtc/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB = lib$(BOARD).a -OBJS = $(BOARD).o oftree.o +OBJS = $(BOARD).o oftree.o nand.o $(LIB): .depend $(OBJS) $(AR) crv $@ $(OBJS) --- /dev/null +++ b/board/stxxtc/nand.c @@ -0,0 +1,78 @@ +/* + * (C) Copyright 2000-2004 + * Pantelis Antoniou, pantelis.antoniou(a)gmail.com + * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. + * (C) Copyright 2005 + * Dan Malek, Embedded Edge, LLC, dan(a)embeddededge.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + +#include <nand.h> + +static void stxxtc_nand_hwcontrol(struct mtd_info *mtd, int cmd) +{ + struct nand_chip *this = mtd->priv; + ulong IO_ADDR_W = (ulong) this->IO_ADDR_W; + volatile immap_t *imap = (volatile immap_t *)CFG_IMMR; + + switch (cmd) { + case NAND_CTL_SETNCE: + imap->im_ioport.iop_padat &= ~(1 << (15 - 7)); + break; + case NAND_CTL_CLRNCE: + imap->im_ioport.iop_padat |= (1 << (15 - 7)); + break; + case NAND_CTL_SETALE: + imap->im_ioport.iop_pcdat |= (1 << (15 - 15)); + break; + case NAND_CTL_CLRALE: + imap->im_ioport.iop_pcdat &= ~(1 << (15 - 15)); + break; + case NAND_CTL_SETCLE: + imap->im_cpm.cp_pbdat |= (1 << (31 - 23)); + break; + case NAND_CTL_CLRCLE: + imap->im_cpm.cp_pbdat &= ~(1 << (31 - 23)); + break; + } +} + +/* + * chip R/B detection + */ +static int stxxtc_nand_ready(struct mtd_info *mtd) +{ + volatile immap_t *imap = (volatile immap_t *)CFG_IMMR; + return !!(imap->im_ioport.iop_padat & (1 << (15 - 6))); +} + +void board_nand_init(struct nand_chip *nand) +{ + nand->options = NAND_SAMSUNG_LP_OPTIONS; + nand->eccmode = NAND_ECC_SOFT; + nand->hwcontrol = stxxtc_nand_hwcontrol; + nand->dev_ready = stxxtc_nand_ready; + nand->chip_delay = 18; +} +#endif --- a/board/stxxtc/stxxtc.c +++ b/board/stxxtc/stxxtc.c @@ -1,6 +1,6 @@ /* * (C) Copyright 2000-2004 - * Pantelis Antoniou, Intracom S.A., panto(a)intracom.gr + * Pantelis Antoniou, Intracom S.A., pantelis.antoniou(a)gmail.com * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. * (C) Copyright 2005 * Dan Malek, Embedded Edge, LLC, dan(a)embeddededge.com @@ -574,22 +574,6 @@ int board_early_init_f(void) return 0; } -#if (CONFIG_COMMANDS & CFG_CMD_NAND) - -#include <linux/mtd/nand.h> - -extern ulong nand_probe(ulong physadr); -extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; - -void nand_init(void) -{ - unsigned long totlen; - - totlen = nand_probe(CFG_NAND_BASE); - printf ("%4lu MB\n", totlen >> 20); -} -#endif - #ifdef CONFIG_HW_WATCHDOG void hw_watchdog_reset(void) --- a/include/configs/stxxtc.h +++ b/include/configs/stxxtc.h @@ -435,88 +435,11 @@ /****************************************************************/ -/* NAND */ -#define CFG_NAND_BASE NAND_BASE -#define CONFIG_MTD_NAND_ECC_JFFS2 -#define CONFIG_MTD_NAND_VERIFY_WRITE -#define CONFIG_MTD_NAND_UNSAFE - -#define CFG_MAX_NAND_DEVICE 1 -#undef NAND_NO_RB - -#define SECTORSIZE 512 -#define ADDR_COLUMN 1 -#define ADDR_PAGE 2 -#define ADDR_COLUMN_PAGE 3 -#define NAND_ChipID_UNKNOWN 0x00 -#define NAND_MAX_FLOORS 1 -#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 +#define CFG_NAND_BASE NAND_BASE +#define CONFIG_NEW_NAND_CODE -/* ALE = PC15, CLE = PB23, CE = PA7, F_RY_BY = PA6 */ -#define NAND_DISABLE_CE(nand) \ - do { \ - (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_padat) |= (1 << (15 - 7)); \ - } while(0) - -#define NAND_ENABLE_CE(nand) \ - do { \ - (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_padat) &= ~(1 << (15 - 7)); \ - } while(0) - -#define NAND_CTL_CLRALE(nandptr) \ - do { \ - (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat) &= ~(1 << (15 - 15)); \ - } while(0) - -#define NAND_CTL_SETALE(nandptr) \ - do { \ - (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat) |= (1 << (15 - 15)); \ - } while(0) - -#define NAND_CTL_CLRCLE(nandptr) \ - do { \ - (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pbdat) &= ~(1 << (31 - 23)); \ - } while(0) - -#define NAND_CTL_SETCLE(nandptr) \ - do { \ - (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pbdat) |= (1 << (31 - 23)); \ - } while(0) - -#ifndef NAND_NO_RB -#define NAND_WAIT_READY(nand) \ - do { \ - int _tries = 0; \ - while ((((volatile immap_t *)CFG_IMMR)->im_ioport.iop_padat & (1 << (15 - 6))) == 0) \ - if (++_tries > 100000) \ - break; \ - } while (0) -#else -#define NAND_WAIT_READY(nand) udelay(12) -#endif - -#define WRITE_NAND_COMMAND(d, adr) \ - do { \ - *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ - } while(0) - -#define WRITE_NAND_ADDRESS(d, adr) \ - do { \ - *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ - } while(0) - -#define WRITE_NAND(d, adr) \ - do { \ - *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ - } while(0) - -#define READ_NAND(adr) \ - ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr))) - -/*****************************************************************************/ - -#define CFG_DIRECT_FLASH_TFTP -#define CFG_DIRECT_NAND_TFTP +#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ /*****************************************************************************/

1 0

[U-Boot-Users] How to bulid a GDB-STUB for AT91RM9200?
by peike 15 Dec '05

15 Dec '05

Hi,Members Merry Christmas! Now,I'm do some thing at Atmel AT92RM9200 target with u-boot-0.4.8,and I want to add a gdb-stub for target into the kernel or u-boot.0.4.8.My u-boot and target OS information is: boot 1.0 (Jun 4 2004 - 17:42:12) U-Boot 0.4.8 (Oct 13 2005 - 16:29:32) U-Boot code: 21F00000 -> 21F13C20 BSS: -> 21F1F9A0 DRAM Configuration: Bank #0: 20000000 64 MB Atmel: AT49BV1614 (16Mbit) Flash: 16 MB In: serial Out: serial Err: serial start linux now(y/n): loading kernel to ram... done loading ramdisk to ram... done start linux... ## Starting application at 0x23000000 ... Uncompressing Linux.............................................................Linux version 2.4.19-rmk7 (root(a)localhost.localdomain) (gcc version 2.95.3 20015CPU: Arm920Tid(wb) revision 0 Machine: ATMEL AT91RM9200 ......................................... BusyBox v1.00-pre10 (2004.06.15-14:16+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. ~ # How can i do? Would you like to give me some supports! Thank you! yours sincerely peike

2 1

[U-Boot-Users] How can I add a gdb-stub into U-boot-0.4.8 for AT91RM9200-DK ?
by peike 15 Dec '05

15 Dec '05

Hello,Wolfgang I'm using u-boot-0.4.8 at Atmel's AT91RM9200-DK machine.Following is information: U-Boot 0.4.8 (Oct 13 2005 - 16:29:32) U-Boot code: 21F00000 -> 21F13C20 BSS: -> 21F1F9A0 DRAM Configuration: Bank #0: 20000000 64 MB Atmel: AT49BV1614 (16Mbit) Flash: 16 MB In: serial Out: serial Err: serial start linux now(y/n): Uboot>tftp 23000000 zImage Uboot> tftp 20800000 ramdisk.image.gz Uboot> go 23000000 *****I download a image by tftp into board's SDRAM and then start it,just like an old friend say"Now, I wonder if it is possible to start the image under control of gdb. As I understand it, there can run a small 'gdb-stub' on the target which talks by serial line or by ethernet with the gdb on the development host. In common/kgdb.c there seems to be something like this small 'gdb-stub'? Does it work for ARM? How can it be used?" *********My question is:If I want to add a debugging stub(at91rm9200dk-stub.c or gdbserver)into u-boot-0.4.8,how to do it? Isn't it a difficult task? ************ The following is my U-boot starting linux process infomormation: start linux... ## Starting application at 0x23000000 ... Uncompressing Linux.............................................................Linux version 2.4.19-rmk7 (root(a)localhost.localdomain) (gcc version 2.95.3 20015CPU: Arm920Tid(wb) revision 0 Machine: ATMEL AT91RM9200 On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: initrd=0x20800000,32M root=/dev/ram init=/linuxrc console0Console: colour dummy device 80x30 Calibrating delay loop... 89.90 BogoMIPS Memory: 64MB = 64MB total Memory: 29796KB available (1804K code, 346K data, 76K init) Dentry cache hash table entries: 8192 (order: 4, 65536 bytes) Inode cache hash table entries: 4096 (order: 3, 32768 bytes) Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded devfs: v1.12a (20020514) Richard Gooch (rgooch(a)atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. S1D13XXX: Phys address:C480F000 Phys Reg address:C480D000 Console: switching to colour frame buffer device 30x20 fb0: s1d13xxx frame buffer device Display 240 x 320 16Bpp pty: 256 Unix98 ptys configured Keyboard(PS/2): initiate successfully! *********************keybd_init************** Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx ioremap:c4a10000 ide0: CPCI405 IDE interface IDE: waiting for drives to settle... IDE: waiting for drives to settle... IDE: waiting for drives to settle... hdb: probing with STATUS(0x28) instead of ALTSTATUS(0x0e) SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). CSLIP: code copyright 1989 Regents of the University of California. RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize PPP generic driver version 2.4.2 SCSI subsystem driver Revision: 1.00 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 AT91ARM9200 flash device: 1000000 at 10000000 Search for id:(89 18) interleave(1) type(2) Search for id:(89 18) interleave(1) type(2) Search for id:(89 18) interleave(1) type(2) Search for id:(89 18) interleave(2) type(1) Search for id:(89 18) interleave(2) type(1) Search for id:(89 18) interleave(2) type(1) Search for id:(89 00) interleave(2) type(2) Search for id:(89 00) interleave(2) type(2) Search for id:(89 00) interleave(2) type(2) JEDEC: Found no AT91ARM9200 flash device device at location zero Using buffer write method Creating 4 MTD partitions on "AT91ARM9200 flash device": 0x00000000-0x00040000 : "reserved for bootloader" mtd: Giving out device 0 to reserved for bootloader 0x00040000-0x00140000 : "reserved for kernel" mtd: Giving out device 1 to reserved for kernel 0x00140000-0x00540000 : "reserved for ramdisk" mtd: Giving out device 2 to reserved for ramdisk 0x00540000-0x00d40000 : "jffs2(8M)" mtd: Giving out device 3 to jffs2(8M) physmap flash device: 800000 at 10540000 Using buffer write method mtd: Giving out device 4 to Physically mapped flash usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb.c: registered new driver usb_mouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver usb.c: registered new driver keyboard usbkbd.c: :USB HID Boot Protocol keyboard driver Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice ttyS%d0 at MEM 0xfefff200 (irq = 1) is a AT91_SERIAL ttyS%d1 at MEM 0xfefc0000 (irq = 6) is a AT91_SERIAL ttyS%d2 at MEM 0xfefc4000 (irq = 7) is a AT91_SERIAL ttyS%d3 at MEM 0xfefc8000 (irq = 8) is a AT91_SERIAL ttyS%d4 at MEM 0xfefcc000 (irq = 9) is a AT91_SERIAL eth0: Link now 100-FullDuplex eth0: AT91 ethernet at 0xfefbc000 int=24 100-FullDuplex (00:01:02:03:04:05) usb-ohci.c: USB OHCI at membase 0xc6219000, IRQ 23 usb.c: new USB bus registered, assigned bus number 1 Product: USB OHCI Root Hub SerialNumber: c6219000 hub.c: USB hub found hub.c: 2 ports detected NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com RAMDISK: Compressed image found at block 0 Freeing initrd memory: 32768K EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Mounted devfs on /dev Freeing init memory: 76K mount /etc as ramfs re-create the /etc/mtab entries eth0: Link now 100-FullDuplex mtdblock_open ok jffs2_read_inode(): No data nodes found for ino #85 jffs2_read_inode(): But it has children so we fake some modes for it exec: 5: /jffs2/etc/ipset: Permission denied Please press Enter to activate this console. BusyBox v1.00-pre10 (2004.06.15-14:16+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. ~ # ls application dev jffs2 linuxrc qt usr bin etc lib mnt sbin var bitmap font linuette proc tmp Please! Thank you very much! yours peike

2 1

[U-Boot-Users] Make can't make a-files
by Zhukov 15 Dec '05

15 Dec '05

Hello, community of u-boot-users! After "make at91rm9200dk_config" I try "make -n". Maker shows a lot, but at the end it complaints "no rule for making *.a" - like this. What is "a" extension about and how to tune the maker? Best regards, Andrew Zhukov mailto:zhukov@tst.spb.su

1 0